Synthesis,characterization, and electroluminescence of PPV copolymers containing electron and hole‐transporting units

Three series of poly(phenylene vinylene) (PPV) derivatives containing hole‐transporting triphenylamine derivatives [N‐(4‐octoxylphenyl)diphenylamine, N,N′‐di(4‐octyloxylphenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine, and N,N′‐di(4‐octoxylphenyl)‐N,N′‐diphenylbenzidine] (donor) and electron‐transporting oxadiazole unit (2,5‐diphenyl‐1,3,4‐oxadiazole) (acceptor) in the main chain were synthesized by improved Wittig copolymerization. The resulting donor–acceptor (D‐A) polymers are readily soluble in common organic solvents, such as chloroform, dichloroethane, THF, and toluene. The polymers containing oxadiazole group exhibit good thermal stability with 5% weight loss above 400 °C. The intramolecular charge‐transfer was observed in these D‐A polymers. In comparison with corresponding polymers without oxadiazole unit, the single‐layer devices based on the D‐A polymers showed much improved electroluminescent properties, because of the balanced charge injection and transport. © 2008 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 1566–1576, 2008     

Blue‐emitting poly[(m‐phenylene vinylene)‐alt‐(o‐phenylene vinylene)]s: The effect of regioregularity on the optical properties

Poly[(m‐phenylene vinylene)‐alt‐(o‐phenylene vinylene)]s with different contents of cis‐/trans‐CH?CH ( 3 and 6 ) have been synthesized through Wittig condensation. The polymers exhibit good solubility in common organic solvents such as toluene and tetrahydrofuran. A comparison of the optical properties has been made between 3 and its phenyl regioisomers containing either p‐phenylene or m‐phenylene units. The results show that the regiochemistry of the phenyl ring can be a useful tool for tuning the emission color of π‐conjugated polymers because the extension of π conjugation can only partially be achieved through an o‐phenylene bridge. Although both polymers 3 and 6 exhibit comparable low fluorescence quantum efficiencies (≈0.18) in solution, their films are highly luminescent, showing a broad emission band near 456 nm (blue color). Electroluminescence results show that the device of polymer 3 , which has a higher content of trans‐CH?CH linkages, is about 20 times more efficient than that of 6 . © 2003 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 2650–2658, 2003     

Synthesis,characterization, and electroluminescence of new conjugated PPV derivatives bearing triphenylamine side‐chain through a vinylene bridge

Three new conjugated poly(p‐phenylene vinylene) (PPV) derivatives bearing triphenylamine side‐chain through a vinylene bridge, poly(2‐(4′‐(diphenylamino)phenylenevinyl)‐1,4‐phenylene‐vinylene) (DP‐PPV), poly(2‐(3′‐(3″,7″‐dimethyloctyloxy)phenyl)‐1,4‐phenylenevinylene‐alt‐2‐(4′‐ (diphenylamino)phenylenevinyl)‐1,4‐phenylenevinylene) (DODP‐PPV), and poly(2‐(4′‐(diphenylamino)phenylenevinyl)‐1,4‐phenylenevinylene‐co‐2‐(3′,5′‐bis(3″,7″‐dimethyloctyloxy)‐1,4‐phenylenevinylene) (DP‐co‐BD‐PPV), were synthesized according to the Gilch or Wittig method. Among the three polymers, the copolymer DP‐co‐BD‐PPV is soluble in common solvents with good thermal stability with 5% weight loss at temperatures higher than 386°C. The weight‐average molecular weight (M_w) and polydispersity index (PDI) of DP‐co‐BD‐PPV were 1.83 × 10⁵ and 2.33, respectively. The single‐layer polymer light‐emitting diodes (PLEDs) with the configuration of Indium tin oxide (ITO)/poly (3,4‐ethylenedioxythiophene): poly(4‐styrene sulfonate)(PEDOT:PSS)/DP‐co‐BD‐PPV/Ca/Al were fabricated. The PLED emitted yellow‐green light with the turn‐on voltage of ca. 4.9 V, the maximum luminance of ca. 990 cd/m² at 15.8 V, and the maximum electroluminescence (EL) efficiency of 0.22 cd/A. Copyright © 2007 John Wiley & Sons, Ltd.     

NMR signal assignment of cis/trans‐conformational segments in MEH‐CN‐PPV

Poly[2‐(2′‐ethylhexyloxy)‐5‐methoxy‐1,4‐phenylene‐(1‐cyanovinylene)] MEH‐CN‐PPV and its all‐trans model compound 1,4‐bis(α‐cyanostyryl)‐2‐(2‐ethylhexyloxy)‐5‐methyloxybenzene were synthesized via Knoevenagel condensation. All‐cis isomer and cis–trans isomer of 1,4‐bis(α‐cyanostyryl)‐2‐(2‐ethylhexyloxy)‐5‐methyloxybenzene were prepared by the photoisomerization reaction. Comparison of the ¹H NMR spectra between MEH‐CN‐PPV and three model compounds proved the occurrence of cis‐vinylene in the backbone of MEH‐CN‐PPV. According to the ratio between the cis‐vinylene signal and trans‐vinylene signal, the content of the cis‐vinylene could be estimated to be 15% in MEH‐CN‐PPV. This large cis‐vinylene content came from the rapid photochemical isomerization of cyanovinylene and was likely relative to the poor electroluminescence property of MEH‐CN‐PPV. © 2008 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 46: 1105–1113, 2008     

Palladium‐catalyzed three‐component coupling polycondensation of aromatic diiodide,aromatic bis(boronic acid propanediol ester), and norbornadiene: A new route for poly(p‐phenylene vinylene)

A novel synthetic method for soluble precursor polymers of poly(p‐phenylene vinylene) (PPV) derivatives by the palladium‐catalyzed three‐component coupling polycondensation of aromatic diiodides, aromatic bis(boronic acid) derivatives, and norbornadiene is described. For example, the polymerization of 1,4‐diiodo‐2,5‐dioctyloxybenzene, benzene‐1,4‐bis(boronic acid propanediol ester), and norbornadiene at 100 °C for 3 days provided a polymer consisting of the three monomer units in a 97% yield (number‐average molecular weight = 3100, weight‐average molecular weight/number‐average molecular weight = 1.37). A derivative of PPV was produced smoothly by the retro Diels–Alder reaction of the polymer both in a dodecyloxybenzene solution and in a film at 200 °C in vacuo. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 3403–3410, 2005     

Novel route to poly(p‐phenylene vinylene) polymers

Poly(p‐phenylene vinylene) (PPV), poly(2,5‐dioctyl‐p‐phenylene vinylene) (PDOPPV), and poly[2‐methoxy‐5‐(2′‐ethylhexyloxy)‐p‐phenylene vinylene] (MEHPPV) were synthesized by a liquid–solid two‐phase reaction. The liquid phase was tetrahydrofuran containing 1,4‐bis(bromomethyl)benzene, 1,4‐bis(chloromethyl)‐2,5‐dioctylbenzene, or 1,4‐bis(chloromethyl)‐2‐methoxyl‐5‐(2′‐ethylhexyloxy)benzene as the monomer and a certain amount of tetrabutylammonium bromide as a phase‐transfer catalyst. The solid phase consisted of potassium hydroxide particles with diameters smaller than 2 mm. The experimental results demonstrated that the reaction conversions of PPV and PDOPPV were fairly high (～65%), but the conversion of MEHPPV was only 45%. Moreover, gelation was found in the polymerization processes. As a result, PPV was insoluble and PDOPPV and MEHPPV were partially soluble in the usual organic solvents, such as tetrahydrofuran and chloroform. Soluble PDOPPV and MEHPPV were obtained with chloromethylbenzene or bromomethylbenzene as a retardant regent. The molar mass of soluble PDOPPV was measured to be 2 × 10⁴ g mol^?1, and that of MEHPPV was 6 × 10⁴ g mol^?1. A thin, compact film of MEHPPV was formed via spin coating, and it emitted a yellow light. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 41: 449–455, 2003     

Dicarboxylic imide‐substituted poly(p‐phenylene vinylenes) with high electron affinity

Synthesis of n‐type organic semiconductors with high electron mobilities, good environmental stability, and good processability is an urgent task in current organic electronics. This is because most of π‐conjugated materials are p‐type and prefer to transport positive hole carriers. In this article, a series of new dicarboxylic imide‐substituted poly(p‐phenylene vinylenes) (DI‐PPVs) were first synthesized. They exhibited a high electron affinity of 3.60 eV and thus are able to transport electrons. The polymers showed tunable solubility in common organic solvents and high chemical and thermal stability. They remain rigidity of the PPV backbone, and strong interchain π‐stacking was observed in thin films by X‐ray diffraction measurement. All these suggested that these polymers could serve as good candidates as n‐type semiconductors in organic electronic devices such as n‐channel field‐effect transistors and all polymer‐based solar cells. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 48: 186–194, 2010     

Donor–acceptor copolymers for red‐ and near‐infrared‐emitting polymer light‐emitting diodes

We report a comparative study of two organic soluble, vinylene‐based, alternating donor–acceptor copolymers with 1,4‐(2,5‐dihexadecyloxyphenylene) as the donor; the acceptor is either a 2,5‐linked pyridine or a 5,8‐linked 2,3‐diphenylpyrido[3,4‐b]pyrazine. The polymers are synthesized via a Heck coupling methodology from a dihalo monomer and a divinyl monomer to yield number‐average molecular weights of 16,000 g/mol for the pyridine polymer (PPyrPV) and 6500 g/mol for the pyridopyrazine polymer (PPyrPyrPV), with high solubility in common chlorinated solvents and lower solubility in less polar solvents (e.g., tetrahydrofuran). Thin‐film measurements show band gaps of 2.2 and 1.8 eV for PPyrPV and PPyrPyrPV, respectively. Both polymers exhibit photoluminescence in solution and in the solid state and exhibit electroluminescence when incorporated into light‐emitting diodes. In this case, a broad red emission centered at 690 nm for PPyrPV and a near‐infrared emission centered at 800 nm for PPyrPyrPV have been observed. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 43: 1417–1431, 2005     

Synthesis and characterization of novel germanium‐containing poly(p‐phenylenevinylene) derivatives

Novel blue‐emitting germanium‐containing poly(p‐phenylenevinylene) (PPV) derivatives with well‐defined conjugation lengths were synthesized via Wittig‐condensation polymerizations. The polymers can be color‐tuned by the introduction of various chromophores into the PPV‐based polymer backbones. The photoluminescence (PL) spectra of the polymers, GePVK (containing carbazole moieties), GeMEH (containing dialkoxybenzene moieties), and GePTH (containing phenothiazine moieties), were found to exhibit blue, greenish blue, and green emissions, respectively. GePTH produces more red‐shifted emission than GeMEH and GEPVK, resulting in green emission, and the solution and solid state PL spectra of GePVK consist of almost blue emission. The electroluminescence spectra of GeMEH and GePTH contain yellowy green and yellow colors, respectively. Interestingly, GePVK exhibits white emission with CIE coordinates of (0.33, 0.37) due to electroplex emission in the light‐emitting diodes. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 46: 979–988, 2008     

Synthesis,photoluminescence, and electrochromism of polyamides containing (3,6‐di‐tert‐butylcarbazol‐9‐yl)triphenylamine units

A new carbazole‐derived, triphenylamine (TPA)‐containing aromatic dicarboxylic acid monomer, 4,4′‐dicarboxy‐4″‐(3,6‐di‐tert‐butylcarbazol‐9‐yl)TPA, was synthesized, and it led to a series of electroactive aromatic polyamides with main‐chain TPA and pendent 3,6‐bis(tert‐butyl)carbazole units by reacting it with various aromatic diamines via the phosphorylation polyamidation technique. The polyamides were amorphous with good solubility in many organic solvents and could be solution‐cast into flexible and strong films. They showed high glass‐transition temperatures (282–335 °C) and high thermal stability (10% weight loss temperatures >480 °C). The electroactive polymer films had well‐defined and reversible redox couples with good cycle stability in acetonitrile solutions. The polymer films also exhibited fluorescent and multielectrochromic behaviors. The anodically electrochromic polyamide films had moderate coloration efficiency (～100 cm²/C) and high optical contrast ratio of transmittance change (Δ%T) up to 47% at 813 nm and 48% at 414 nm for the green coloring. After hundreds of cyclic switches, the polymer films still retained good redox and electrochromic activity. © 2010 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem, 2010     

Synthesis and characterization of highly hindered and thermally stable poly(1,4‐spirobifluorenylenevinylene) derivative

A new poly(1,4‐spirobifluorenylenevinylene) having advantage PPV and spirobifluorene as new emissive family was synthesized. Compared with PPV derivatives that usually have a tolane bisbenzyl defect, the polymer has the defect free structure because of the steric hindrance of the asymmetric bulky spirobifluorenyl group. Compared with spirobifluorene derivatives that usually have a low solubility, the polymer has the good solubility in common organic solvents. The polymer was amorphous and showed high PL quantum efficiency and high thermal stability with high T_g. The PL emission peaks were shown at 480–490 nm in solution and film, respectively, which may represent the bluest emission peak reported for fully conjugated PPV derivatives. The study of thermal annealing of PL spectrum showed excimer formation inhibited. The thermal and optoelectronic properties of the polymer imply that it is a promising material for the PLED application. © 2007 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 45: 900–907, 2007.     

Synthesis and characterization of novel soluble triphenylamine‐containing aromatic polyamides based on N,N′‐bis(4‐aminophenyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new triphenylamine‐containing aromatic diamine, N, N′‐bis(4‐aminophenyl)‐N, N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 4‐fluoronitrobenzene, followed by catalytic reduction. A series of novel aromatic polyamides with triphenylamine units were prepared from the diamine and various aromatic dicarboxylic acids or their diacid chlorides via the direct phosphorylation polycondensation or low‐temperature solution polycondensation. All the polyamides were amorphous and readily soluble in many organic solvents such as N, N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with good mechanical properties. They had useful levels of thermal stability associated with relatively high glass‐transition temperatures (257–287 °C), 10% weight‐loss temperatures in excess of 550 °C, and char yields at 800 °C in nitrogen higher than 72%. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2810–2818, 2002     

Near‐infrared electrochromic poly(aryl ether)s based on isolated electroactive tetraphenyl‐p‐phenylenediamine moieties

A series of near‐infrared (NIR) electrochromic aromatic poly(aryl ether)s containing N,N,N′,N′‐tetraphenyl‐p‐phenylenediamine (TPPA) moieties in the backbone were prepared from the high‐temperature polycondensation reactions of a biphenol monomer, 2,5‐bis(diphenylamino)hydroquinone, with difluoro compounds. The obtained polymers were readily soluble in many organic solvents and showed useful levels of thermal stability associated with high glass‐transition temperatures (182–205 °C) and high char yields (higher than 40% at 800 °C in nitrogen). The polymer films showed reversible electrochemical oxidation with high contrast ratio both in the visible range and NIR region, and also exhibited high coloration efficiency (CE), low switching time, and stability for electrochromic operation. The polyether TPPA‐a thin film revealed good CE in visible (CE = 217 cm²/C) and NIR (CE = 192 cm²/C) region with reversible electroactive stability (over 500 times within 5% loss relative to its initial injected charge). © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 5378–5385, 2009     

Control of molecular aggregation in symmetrically substituted π‐conjugated bulky poly(p‐phenylenevinylene)s and their copolymers

A new series of symmetrically substituted bulky PPV‐copolymers based on poly(bis‐2,5‐(2‐ethylhexyloxy)‐1,4‐phenylenevinylene) ( BEH‐PPV ) bearing tricyclodecane (TCD) pendants were synthesized to study the effect of chain aggregation in the π‐conjugated polymer backbone. The composition of the copolymers was varied up to 100 mol % and the structures of the copolymer were confirmed by NMR and FTIR. The molecular weights of the copolymers were obtained as M_w = 11,500–1,78,800 depending on the TCD‐incorporation in BEH‐PPV. The origin of the π‐aggregation was investigated using mixture of solvents (polar or nonpolar) or temperature as external stimuli. Absorption, photoluminescence, and time‐resolved fluorescence decay techniques were employed as tools to trace molecular aggregation in solution and solid state. The TCD‐substituted bulky copolymers showed almost twice the enhancement in photoluminescence compared with that of BEH‐PPV . Solvent‐induced aggregation studies of copolymers revealed the existence of strong molecular aggregation in BEH‐PPV compared with that of bulky copolymers. Variable temperature studies further evidence for the reversibility of molecular aggregation on heating/cooling cycles and showed isosbetic points with respect to free and aggregated polymer chains. Time‐resolved fluorescent studies confirmed the existence of free and aggregated π‐conjugated species with a life time of 0.1 to 1.0 ns. © 2009 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 47: 2631–2646, 2009     

Photoluminescent properties of poly(p‐phenylene vinylene thiophene‐co‐siloxane)

A new p‐phenylene–vinylene–thiophene‐based siloxane block copolymer has been synthesized. The copolymer consists of alternating rigid and flexible blocks. The rigid blocks are composed of phenylene–vinylene–thiophene‐based units, and the flexible blocks are derived from 1,3‐dialkyldisiloxane units. The former component acts as the chromophore, and allows fine tuning of band gap for blue‐light emission, while the latter imparts good solubility of the copolymer in organic solvents, and thus, should enhance processibility of the resulting copolymer. The thermal properties of the copolymer have been characterized by thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). The photoluminescence (PL) of the copolymer in solution and in cast film has been studied. The effects of concentration on the PL intensity of the new copolymer in polymer blends with poly(methyl methacrylate) (PMMA) and poly(vinyl carbazole) (PVK) have also been described. Efficient energy transfer from PVK to the new block copolymer in the blended film was observed. © 2000 John Wiley & Sons, Inc. J Polym Sci A: Polym Chem 38: 1450–1456, 2000     

Poly‐p‐phenylenevinylene‐g‐poly(2‐(methacryloyloxy)Ethyl)trimethylammonium chloride (PPV‐g‐PMETAC): A fluorescent,water‐soluble,selective anion sensor

The photophysical and ion‐sensing properties of densely grafted conjugated polymer poly‐p‐phenylenevinylene‐g‐poly(2‐(methacryloyloxy)ethyl)trimethylammonium chloride (PPV‐g‐PMETAC) are presented herein. The grafted polymer exhibits excellent iodide‐sensing which is easily observed using fluorescence spectroscopy. The iodide detection limit for PPV‐g‐PMETAC was found to be 10 nM and was independent of temperature and pH <12. The change in fluorescence of PPV‐g‐PMETAC, upon exposure to iodide, was attributed to polymer aggregation due to changes in the morphology of the grafted PMETAC side chains, which was observed using atomic force microscopic and dynamic light scattering studies. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 1997–2003     

Synthesis and characterization of luminescent polyethers with 2,5‐distyrylthiophene and aromatic oxadiazole chromophores

Two new luminescent copolyethers ( P1 and P2 ) with isolated 2,5‐distyrylthiophene‐emitting segments and electron‐transporting 2,5‐diphenyl‐1,3,4‐oxadiazole chromophores were successfully synthesized by the Horner–Wadworth–Emmons reaction. The solubility, optical, and electrochemical properties of the polymers were investigated and correlated with nonlinear thiophene and 1,3,4‐oxadiazole groups. P2 with pendant 1,3,4‐oxadiazole was soluble in common organic solvents such as chloroform, tetrahydrofuran, and C₂H₂Cl₄. Thermogravimetric analysis and differential scanning calorimetry showed that the copolyethers were thermally stable below 345 °C, with glass‐transition temperatures higher than 110 °C. They were yellow‐greenish emitting materials with a band gap of 2.57–2.58 eV estimated from the onset absorption. Incorporating the thiophene moiety narrowed the band gaps of the copolyethers. The photophysical and electronic properties of the polymer and the preliminary electroluminescent device made from the polymer demonstrate that the polymer may be a potential candidate material for the fabrication of polymeric light‐emitting devices. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2927–2936, 2002     

Synthesis and characterization of spirobifluorene‐based polyimides

The synthesis and properties of organosoluble aromatic polyimides, containing spiro‐skeletal units in the polymer backbone on the basis of the spiro‐diamine monomer, 2,2′‐diamino‐9,9′‐spirobifluorene, are described. In the case of the spiro segment, the two fluorene rings are orthogonally arranged and connected through a tetrahedral bonding carbon atom, the spiro center. As a consequence, the polymer chain is periodically zigzagged with a 90° angle at each spiro center. This structural feature minimizes interchain interactions and restricts the close packing of the polymer chains, resulting in amorphous polyimides that have good solubility in organic solvents. Compared with their fluorene‐based cardo analogues, the spirobifluorene‐based polyimides have an improved solubility. Furthermore, the main‐chain rigidity of the polyimide appears to be preserved because of the presence of the spiro structure, which restricts the free segmental mobility. As a result, these polyimides exhibit a high glass‐transition temperature (T_g's) and good thermal stability. The T_g's of these polyimides were in the range of 287–374 °C, and the decomposition temperatures in nitrogen for a 10% weight loss occurred at temperatures above 570 °C. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 3615–3621, 2002     

Transparent and soluble polyimide films containing 4,4′‐isopropylidenedicyclohexanol (Cis‐HBPA) units: Preparation,characterization, thermal,mechanical, and dielectric properties

To develop colorless and soluble polyimide films, cis‐hydrogenated bisphenol A (cis‐HBPA) was successfully separated from HBPA isomers, and two novel monomers containing cis‐HBPA unit, 4,4 ′ ‐(4,4 ′ ‐isopropenylbicyclohexyloxy) diphthalic anhydride (HBPADA) and 4,4 ′ ‐(4,4 ′ ‐isopropenylbicyclohexyloxy) dianiline (f) were designed and synthesized. PI–(1 – 5) were achieved from HBPADA and five kinds of aromatic diamines and PI – 6 from HBPADA and semiaromatic diamine f via a two‐step thermal imidization. All the polyimides could afford flexible, tough, and transparent films with transparency as high as 86% at 450 nm. Surprisingly, the polyimides containing cis‐HBPA unit exhibited excellent solubility not only in polar solvents such as N, N‐dimethylacetamide, but also in low boiling solvents such as chloroform and dichloromethane. Additionally, analogues aromatic PI – 7 derived from 4,4 ′ ‐(hexafluoroisopropylidene)‐diphthalic anhydride (6FDA) and 2,2‐bis(4‐aminophenyl)hexafluoropropane (e) was obtained for comparison with PI–(1 – 6) on aspects of thermal, mechanical, soluble, optical, electrical, and morphological properties. The structure‐property relationships of PI–(1 – 7) were investigated in detail. © 2018 Wiley Periodicals, Inc. J. Polym. Sci., Part A: Polym. Chem. 2018 , 56, 2115–2128     

Synthesis and properties of new soluble aromatic polyamides and polyimides on the basis of N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine

A new N‐phenylated amide (N‐phenylamide) unit containing aromatic diamine, N,N′‐bis(3‐aminobenzoyl)‐N,N′‐diphenyl‐1,4‐phenylenediamine, was prepared by the condensation of N,N′‐diphenyl‐1,4‐phenylenediamine with 3‐nitrobenzoyl chloride, followed by catalytic reduction. Two series of organosoluble aromatic poly(N‐phenylamide‐imide)s and poly(N‐phenylamide‐amide)s with inherent viscosities of 0.58–0.82 and 0.56–1.21 dL/g were prepared by a conventional two‐stage method and the direct phosphorylation polycondensation, respectively, from the diamine with various aromatic dianhydrides and aromatic dicarboxylic acids. All polyimides and polyamides are amorphous and readily soluble in many organic solvents such as N,N‐dimethylacetamide and N‐methyl‐2‐pyrrolidone. These polymers could be solution cast into transparent, tough, and flexible films with high tensile strengths. These polyimides and polyamides had glass‐transition temperatures in the ranges of 230–258 and 196–229 °C, respectively. Decomposition temperatures of the polyimides for 10% weight loss all occurred above 500 °C in both nitrogen and air atmospheres. © 2002 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 40: 2564–2574, 2002