聚苯胺对新型杂化透明导电薄膜制备和性能的影响

以聚苯胺和掺锑的氧化锡作为主要原料, 采用溶胶-凝胶法制备了新型有机-无机杂化透明导电薄膜. 薄膜的可见光透过率为85%以上, 电导率达到10⁰～10¹ S•cm^－1. 研究了聚苯胺含量的变化对浸涂液粘度、薄膜结构、光透过率、电导率的影响. 随着聚苯胺引入量的增加, 薄膜的电导率、可见光透过率均有所增大. 浸涂液的粘度可在长达25天的时间内保持稳定, 很适于浸涂工艺. 扫描电镜照片显示, 薄膜比较致密、均匀, 厚度为250 nm左右.     

二氧化硅-聚苯胺(SiO2-PANI)杂化透明导电薄膜的制备和表征

本文采用溶胶-凝胶法,以3-巯丙基三甲氧基硅烷(MPTMS)和聚苯胺为主要原料,制备得到有机-无机杂化透明导电薄膜。着重研究制备过程中醋酸、间甲酚和聚苯胺含量对薄膜结构、导电性和可见光透过率的影响。通过红外光谱可知,采用溶胶-凝胶法可制得结构稳定的杂化导电材料。醋酸作为水解缩聚反应的反应剂和催化剂,当其与3-巯丙基三甲氧基硅烷的物质的量比为0.4时,MPTMS的水解缩聚速率和聚苯胺掺杂入无机前驱体的掺杂速率达到平衡。此外,透明杂化导电薄膜的方块电阻随间甲酚和聚苯胺含量的增加而降低,当间甲酚和3-巯丙基三甲氧基硅烷的物质的量比为5,聚苯胺和二氧化硅的质量比为3/7时,薄膜的方块电阻为3.23 kΩ/□,可见光透过率为80%。     

A High-Performance Asymmetric Supercapacitor Based on Tungsten Oxide Nanoplates and Highly Reduced Graphene Oxide Electrodes

Tungsten oxide/graphene hybrid materials are attractive semiconductors for energy-related applications. Herein, we report an asymmetric supercapacitor (ASC, HRG//m-WO₃ ASC), fabricated from monoclinic tungsten oxide (m-WO₃) nanoplates as a negative electrode and highly reduced graphene oxide (HRG) as a positive electrode material. The supercapacitor performance of the prepared electrodes was evaluated in an aqueous electrolyte (1 m H₂SO₄) using three- and two-electrode systems. The HRG//m-WO₃ ASC exhibits a maximum specific capacitance of 389 F g⁻¹ at a current density of 0.5 A g⁻¹, with an associated high energy density of 93 Wh kg⁻¹ at a power density of 500 W kg⁻¹ in a wide 1.6 V operating potential window. In addition, the HRG//m-WO₃ ASC displays long-term cycling stability, maintaining 92 % of the original specific capacitance after 5000 galvanostatic charge–discharge cycles. The m-WO₃ nanoplates were prepared hydrothermally while HRG was synthesized by a modified Hummers method.     

氧化石墨烯水热还原前后的发光光谱

分别采用改进Hummers方法和水热还原法制备了氧化石墨烯(GO)和还原氧化石墨烯(RGO)。 GO和RGO经透射电子显微镜(TEM)、紫外-可见吸收光谱(UV-Vis)、红外光谱(IR)、荧光发射和激发光谱(PL、PLE)等技术手段进行了表征。 荧光发射光谱显示,氧化石墨烯(GO)在可见光的激发下可以得到波长在600~800 nm范围内的宽谱近红外荧光。 通过比较氧化石墨烯水热还原前后的光谱变化,发现氧化石墨烯近红外荧光起源于氧化石墨烯的表面含氧基团,如C=O、COOH。 近红外荧光穿透性好、对生物组织损坏小,非常适合于生物成像,预示着氧化石墨烯在生物成像方面的应用潜力。     

Functionalization of Graphene Derivatives with Conducting Polymers and Their Applications in Uric Acid Detection

In this article, we review recent progress concerning the development of sensorial platforms based on graphene derivatives and conducting polymers (CPs), alternatively deposited or co-deposited on the working electrode (usually a glassy carbon electrode; GCE) using a simple potentiostatic method (often cyclic voltammetry; CV), possibly followed by the deposition of metallic nanoparticles (NPs) on the electrode surface (ES). These materials have been successfully used to detect an extended range of biomolecules of clinical interest, such as uric acid (UA), dopamine (DA), ascorbic acid (AA), adenine, guanine, and others. The most common method is electrochemical synthesis. In the composites, which are often combined with metallic NPs, the interaction between the graphene derivatives—including graphene oxide (GO), reduced graphene oxide (RGO), or graphene quantum dots (GQDs)—and the CPs is usually governed by non-covalent functionalization through π–π interactions, hydrogen bonds, and van der Waals (VW) forces. The functionalization of GO, RGO, or GQDs with CPs has been shown to speed up electron transfer during the oxidation process, thus improving the electrochemical response of the resulting sensor. The oxidation mechanism behind the electrochemical response of the sensor seems to involve a partial charge transfer (CT) from the analytes to graphene derivatives, due to the overlapping of π orbitals.     

Enhancing Hematite Photoanode Activity for Water Oxidation by Incorporation of Reduced Graphene Oxide

Two effective methods to prepare reduced graphene oxide (rGO)/hematite nanostructured photoanodes and their photoelectrochemical characterization towards water splitting reactions are presented. First, graphene oxide (GO) is reduced to rGO using hydrazine in a basic solution containing tetrabutylammonium hydroxide (TBAOH), and then deposited over the nanostructured hematite photoanodes previously treated at 750 °C for 30 min. The second method follows the deposition of a paste containing a mixture of hematite nanoparticles and rGO sheets by the doctor‐blade method, varying the rGO concentration. Since hematite suffers from low electron mobility, a low absorption coefficient, high recombination rates and slow reaction kinetics, the incorporation of rGO in the hematite can overcome such limitations due to graphene's exceptional properties. Using the first method, the rGO incorporation results in a photocurrent density increase from 0.56 to 0.82 mA cm^?2 at 1.23 V_RHE. Our results indicate that the rGO incorporation in the hematite photoanodes shows a positive effect in the reduction of the electron–hole recombination rate.     

石墨烯的制备、表征及其在透明导电膜中的应用

近年来,石墨烯因其优异的电学和光学等特性,越来越受到人们的广泛关注。研究人员应用多种方法来合成石墨烯并且探讨其潜在的应用价值。本文首先简要介绍了石墨烯的结构及其基本的物理性质,并简单回顾了石墨烯的合成方法和表征手段。在此基础上,讨论了石墨烯/银复合薄膜在透明导电膜中的应用,并详细介绍了我们在该领域的研究成果。用化学气相沉积法（CVD）和多羟基法分别制备了双层石墨烯及银纳米线,成功合成了石墨烯/银复合薄膜,结果表明复合薄膜的方块电阻可降低至26 Ω·□-1,展示了其在光电器件上广泛的应用前景。     

Ultralight,Ultraflexible, Anisotropic,Highly Thermally Conductive Graphene Aerogel Films

Graphene aerogels have attracted much attention as a promising material for various applications. The unusually high intrinsic thermal conductivity of individual graphene sheets makes an obvious contrast with the thermal insulating performance of assembled 3D graphene materials. We report the preparation of anisotropy 3D graphene aerogel films (GAFs) made from tightly packed graphene films using a thermal expansion method. GAFs with different thicknesses and an ultimate low density of 4.19 mg cm⁻³ were obtained. GAFs show high anisotropy on average cross-plane thermal conductivity (K_⊥) and average in-plane thermal conductivity (K_||). Additionally, uniaxially compressed GAFs performed a large elongation of 11.76% due to the Z-shape folding of graphene layers. Our results reveal the ultralight, ultraflexible, highly thermally conductive, anisotropy GAFs, as well as the fundamental evolution of macroscopic assembled graphene materials at elevated temperature.     

The Influence of Lateral Size and Oxidation of Graphene Oxide on Its Chemical Reduction and Electrical Conductivity of Reduced Graphene Oxide

The chemical reduction efficiencies of graphene oxide (GO) are critically important in achieving graphene-like properties in reduced graphene oxide (rGO). In this study, we assessed GO lateral size and its degree of oxidation effect on its chemical reduction efficiency in both suspension and film and the electrical conductivity of the corresponding rGO films. We show that while GO-reduction efficiency increases with the GO size of lower oxidation in suspension, the trend is opposite for film. FESEM, XRD, and Raman analyses reveal that the GO reduction efficiency in film is affected not only by GO size and degree of oxidation but also by its interlayer spacing (restacking) and the efficiency is tunable based on the use of mixed GO. Moreover, we show that the electrical conductivity of rGO films depends linearly on the C/O and Raman I_D/I_G ratio of rGO and not the lateral size of GO. In this study, an optimal chemical reduction was achieved using premixed large and small GO (L/SGO) at a ratio of 3:1 (w/w). Consequently, the highest electrical conductivity of 85,283 S/m was achieved out of all rGO films reported so far. We hope that our findings may help to pave the way for a simple and scalable method to fabricate tunable, electrically conductive rGO films for electronic applications.     

Highly Conductive Graphene and Polyelectrolyte Multilayer Thin Films Produced From Aqueous Suspension

Rapid, large‐scale exfoliation of graphene in water has expanded its potential for use outside niche applications. This work focuses on utilizing aqueous graphene dispersions to form thin films using layer‐by‐layer processing, which is an effective method to produce large‐area coatings from water‐based solutions of polyelectrolytes. When layered with polyethyleneimine, graphene flakes stabilized with cholate are shown to be capable of producing films thinner than 100 nm. High surface coverage of graphene flakes results in electrical conductivity up to 5500 S m⁻¹. With the relative ease of processing, the safe, cost effective nature of the ingredients, and the scalability of the deposition method, this system should be industrially attractive for producing thin conductive films for a variety of electronic and antistatic applications.

     

Multifunctionality of Reduced Graphene Oxide in Bioderived Polylactide/Poly(Dodecylene Furanoate) Nanocomposite Films

This work reports on the first attempt to prepare bioderived polymer films by blending polylactic acid (PLA) and poly(dodecylene furanoate) (PDoF). This blend, containing 10 wt% PDoF, was filled with reduced graphene oxide (rGO) in variable weight fractions (from 0.25 to 2 phr), and the resulting nanocomposites were characterized to assess their microstructural, thermal, mechanical, optical, electrical, and gas barrier properties. The PLA/PDoF blend resulted as immiscible, and the addition of rGO, which preferentially segregated in the PDoF phase, resulted in smaller (from 2.6 to 1.6 µm) and more irregularly shaped PDoF domains and in a higher PLA/PDoF interfacial interaction, which suggests the role of rGO as a blend compatibilizer. rGO also increased PLA crystallinity, and this phenomenon was more pronounced when PDoF was also present, thus evidencing a synergism between PDoF and rGO in accelerating the crystallization kinetics of PLA. Dynamic mechanical thermal analysis (DMTA) showed that the glass transition of PDoF, observed at approx. 5 °C, shifted to a higher temperature upon rGO addition. The addition of 10 wt% PDoF in PLA increased the strain at break from 5.3% to 13.0% (+145%), and the addition of 0.25 phr of rGO increased the tensile strength from 35.6 MPa to 40.2 MPa (+13%), without significantly modifying the strain at break. Moreover, rGO decreased the electrical resistivity of the films, and the relatively high percolation threshold (between 1 and 2 phr) was probably linked to the low aspect ratio of rGO nanosheets and their preferential distribution inside PDoF domains. PDoF and rGO also modified the optical transparency of PLA, resulting in a continuous decrease in transmittance in the visible/NIR range. Finally, rGO strongly modified the gas barrier properties, with a remarkable decrease in diffusivity and permeability to gases such as O₂, N_2, and CO₂. Overall, the presented results highlighted the positive and sometimes synergistic role of PDoF and rGO in tuning the thermomechanical and functional properties of PLA, with simultaneous enhancement of ductility, crystallization kinetics, and gas barrier performance, and these novel polymer nanocomposites could thus be promising for packaging applications.     

Gold Nano Particle and Reduced Graphene Oxide Composite Modified Carbon Paste Electrode for the Ultra Trace Detection of Arsenic (III)

Gold nanoparticles (AuNPs) and reduced graphene oxide (RGO) composite modified carbon paste electrode (CPE) was prepared by electrodepositing AuNPs over the reduced graphene oxide (RGO) modified carbon paste electrode. The composite material was characterised using scanning electron microscopy (SEM) and transmission electron microscopy (TEM) and atomic force microscopy (AFM) techniques. The nano composite modified electrode was applied for the determination of total As and for the inorganic speciation of As(III) and As(V) in environmental samples. The linear dynamic range was obtained for the determination of As(III) in the present method from 1μgL⁻¹ to 20 μgL⁻¹ and the limit of detection(LOD) in the standard solution was found to be 0.13 μgL⁻¹ for the 300 sec deposition time in 10 mL supporting electrolyte solution. This method was applied for the determination of As (III) in water and soil samples. The results were agreed well with the result obtained from the hydride generation atomic absorption spectrometry.     

Three‐Dimensional Nitrogen‐Doped Reduced Graphene Oxide–Carbon Nanotubes Architecture Supporting Ultrafine Palladium Nanoparticles for Highly Efficient Methanol Electrooxidation

A three‐dimensional (3D) nitrogen‐doped reduced graphene oxide (rGO)–carbon nanotubes (CNTs) architecture supporting ultrafine Pd nanoparticles is prepared and used as a highly efficient electrocatalyst. Graphene oxide (GO) is first used as a surfactant to disperse pristine CNTs for electrochemical preparation of 3D rGO@CNTs, and subsequently one‐step electrodeposition of the stable colloidal GO–CNTs solution containing Na₂PdCl₄ affords rGO@CNTs‐supported Pd nanoparticles. Further thermal treatment of the Pd/rGO@CNTs hybrid with ammonia achieves not only in situ nitrogen‐doping of the rGO@CNTs support but also extraordinary size decrease of the Pd nanoparticles to below 2.0 nm. The resulting catalyst is characterized by scanning and transmission electron microscopy, X‐ray diffraction, Raman spectroscopy, and X‐ray photoelectron spectroscopy. Catalyst performance for the methanol oxidation reaction is tested through cyclic voltammetry and chronoamperometry techniques, which shows exceedingly high mass activity and superior durability.     

Reduced and Surface‐Modified Graphene Oxide with Nonlinear Resistivity

Field‐grading materials (FGMs) are used to reduce the probability for electrical breakdowns in critical regions of electrical components and are therefore of great importance. Usually, FGMs are heavily filled (40 vol.%) with semi‐conducting or conducting particles. Here, polymer‐grafted reduced graphene oxide (rGO) is used as a filler to accomplish percolated networks at very low filling ratios (<2 vol.%) in a semi‐crystalline polymer matrix: poly(ethylene‐co‐butyl acrylate) (EBA). Various simulation models are used to predict the percolation threshold and the flake‐to‐flake distances, to complement the experimental results. A substantial increase in thermal stability of rGO is observed after surface modification, either by silanization or subsequent polymerizations. The non‐linear DC resistivity of neat and silanized rGO and its trapping of charge‐carriers in semi‐crystalline EBA are demonstrated for the first time. It is shown that the polymer‐grafted rGO improve the dispersibility in the EBA‐matrix and that the graft length controls the inter‐flake distances (i.e. charge‐carrier hopping distances). By the appropriate selection of graft lengths, both highly resistive materials at 10 kV mm^‐1 and FGMs with a large and distinct drop in resistivity (six decades) are obtained, followed by saturation. The nonlinear drop in resistivity is attributed to narrow inter‐flake distance distributions of grafted rGO.     

The Effects of Hydrophobicity and Textural Properties on Hexamethyldisiloxane Adsorption in Reduced Graphene Oxide Aerogels

To expand the applications of graphene-based materials to biogas purification, a series of reduced graphene oxide aerogels (rGOAs) were prepared from industrial grade graphene oxide using a simple hydrothermal method. The influences of the hydrothermal preparation temperature on the textural properties, hydrophobicity and physisorption behavior of the rGOAs were investigated using a range of physical and spectroscopic techniques. The results showed that the rGOAs had a macro-porous three-dimensional network structure. Raising the hydrothermal treatment temperature reduced the number of oxygen-containing groups, whereas the specific surface area (S_BET), micropore volume (V_micro) and water contact angle values of the rGOAs all increased. The dynamic adsorption properties of the rGOAs towards hexamethyldisiloxane (L2) increased with increasing hydrothermal treatment temperature and the breakthrough adsorption capacity showed a significant linear association with S_BET, V_micro and contact angle. There was a significant negative association between the breakthrough time and inlet concentration of L2, and the relationship could be reliably predicted with a simple empirical formula. L2 adsorption also increased with decreasing bed temperature. Saturated rGOAs were readily regenerated by a brief heat-treatment at 100 °C. This study has demonstrated the potential of novel rGOA for applications using adsorbents to remove siloxanes from biogas.