微波消解—氟离子选择电极法测定树叶中氟离子含量

采用微波消解处理样品,氟离子选择电极法测定了树叶中氟离子含量;通过正交实验考察了微波功率、消解时间、固液比、冷却时间等条件对微波消解的影响,对消解试剂和微波消解条件进行了筛选和优化。结果表明,其相对标准偏差小于0.46%,加标回收率在95.5%~103.3%之间。该法简单快速、准确可靠,对测定植物树叶中氟离子含量十分有效。     

有机酸对离子色谱法测定氟离子的影响

比较了不同体系下离子色谱法测定考核样中氟离子的准确度。在碳酸盐–碳酸氢盐体系下分析氟标准样品,进行甲酸根、乙酸根加标试验,讨论了甲酸根、乙酸根对氟定量准确性的影响。考核样品色谱峰处理前氟测定结果为0.273 mg/L,与统计均值0.240 mg/L相比偏高,色谱峰处理后结果为0.243 mg/L,在统计Z值偏差范围内。同时在氢氧根体系下分析考核样品,有效改善了氟离子与乙酸、甲酸的分离度。在氢氧根体系下分析环境水样中低浓度氟离子快速、方便。     

离子色谱法检测植物提取液中痕量氟

介绍了一种采用OnGuardⅡ H柱进行样品前处理,抑制型电导离子色谱法检测,测定经管式炉燃烧水解后的浓碱性植物提取液中痕量氟的方法。色谱柱为:氢氧化物选择性的IonPac AS18阴离子交换柱,氢氧化钠等度淋洗。样品通过Dionex OnGuardⅡ氢型聚苯乙烯基强酸性树脂柱和0.22μm微孔尼龙膜处理。该方法检出限(S/N=3)为0.64μg/L,线性相关系数r=0.999 9,RSD为2.6%,回收率为95%~101%,具有灵敏度高,选择性好,操作简单,节省时间等特点,用于实际样品的检测,结果令人满意。     

氟离子选择电极法在测试中应注意的问题

氟元素的测定方法主要有茜素酮比色法和氟离子选择电极法。前者使用试剂较多,但结果准确;后者具有结构简单牢固、灵敏度高、晌应速度快等优点而被广泛地应用。本文就氟离子选择电极法测试中应注意的问题进行归纳和总结。1　电极的响应极限氟离子选择电极在初次使用时,应首先测试其响应极限,由此可准确估计样品的最低检出限。氟离子选择电极的响应极限为0.05mg/L左右。若待测液中氟离子活度小于电极的响应极限,可使用标准加入法,克服因测试电位值与氟离子活度的对数不成线性关系造成的误差,满足分析测试的精密度和准确度。2　氟离子选择电极…     

离子色谱法同时测定离子液体中六氟磷酸根及痕量杂阴离子

建立了一种同时测定离子液体中六氟磷酸根(PF~6)和痕量杂阴离子氟、氯、溴(F~,Cl~,Br~)的离子色谱方法(IC)。样品经溶解、稀释、过滤后用Dionex IonPac AS22分离柱(250 mm×4 mm)分离,淋洗液为碳酸盐-乙腈体系(体积比为70:30),流速1.0 mL/min,采用Dionex DS6电导检测器检测,外标法定量。F~,Cl~,Br~和PF~6的线性范围分别为0.5～50 μg/L、10～200 μg/L、10～200 μg/L和0.9～45 mg/L,线性相关系数分别为0.9999,0.9998,0.9999和0.9998,加标回收率为94.5%～100.5%,相对标准偏差为0.63%～1.03%,检出限(以信噪比为3计)分别为0.5 μg/L、2.0 μg/L、5.0 μg/L和0.9 mg/L。该方法用于离子液体中六氟磷酸根和痕量杂阴离子的同时测定,结果令人满意。     

离子选择电极法测定植物叶片中的氟

采用硝酸溶液消解,超声波处理植物叶片,以柠檬酸钠溶液作离子强度缓冲调节剂,用氟离子选择性电极进行测定植物叶片中的氟。研究了浸提条件对测定影响,确定了最佳试验条件,该法用于植物叶片中氟化物的分析,回收率为93.0％-99.0％,相对标准偏差为3．1％-4．1％。     

离子色谱-柱切换法测定土壤浸出液中的氟离子

建立了离子色谱-柱切换测定土壤浸出液中氟离子的方法。使用柱切换技术,将样品通过高聚物反相色谱柱进行在线预处理,分离氟离子和小分子有机酸,同时除去水溶性有机杂质,采用收集环收集氟离子并进入分析系统分析,消除了测定氟离子时普遍存在的干扰问题。分析系统的淋洗液为KOH溶液,流速为1.0 mL/min,采用抑制性电导检测,外标法定量。氟离子的线性范围为0.05~10.0 mg/L,相关系数为0.9999,加标回收率为103.4%~105.3%,相对标准偏差为2.0%~2.1%,检出限 (S/N=3)为5.50 μg/L。该方法适用于测定复杂基体样品中的氟离子。     

离子选择性电极快速测定植物中氟

氟离子选择电极测定植物中氟有灰化法,氧瓶燃烧法、氢氧化钠熔融法和酸浸提法等。这些方法分析时间长、操作繁琐,且均需加入TISAB(总离子强度缓冲溶液)使pH=5～5.5,以防止低pH值时生成HF缔合物和高pH值时OH的干扰。为了达到快速分析的目的,我们在pH≈1时,不加TISAB,用标准加入法直接测定植物中氟,每次测定只需约30min。方法的精密度与准确度较好,分析结果与盐酸浸提法结果无     

固相萃取–离子色谱法测定人尿液中钙、镁、氟、磷酸根离子

建立固相萃取–离子色谱法测定人尿液中钙、镁两种阳离子和氟、磷酸根两种阴离子。采用C₁₈固相萃取柱去除样品中杂质以消除干扰,以CS12 A型阳离子交换柱为分离柱,以甲基磺酸溶液为淋洗液,等度洗脱,测定钙、镁离子;以AS15型阴离子交换柱为分离柱,以KOH溶液为淋洗液,梯度洗脱,测定氟、磷酸根离子。钙、镁离子的质量浓度在0.25～10 mg/L范围内,氟、磷酸根离子的质量浓度分别在0.002 5～0.05 mg/L、1.25～50 mg/L范围内与色谱峰面积具有良好的线性关系,相关系数均大于0.999 0,方法检出限为0.002～0.2 mg/L。样品加标回收率为86.0%～99.5%,测定结果的相对标准偏差为0.12%～5.50%(n=6)。该方法操作简便,灵敏度高。     

碱融浸取–离子选择电极法测定固体废物中的总氟

采用氢氧化钠熔融浸取固体废物中的氟,用离子选择电极法测定其中的总氟含量。固体废物样品经氢氧化钠高温熔融后,以热纯水浸取并加入适量的盐酸使溶液呈弱碱性,去除主要干扰离子。测定氟的线性范围为5.00~500μg,线性相关系数r=0.999 6,检出限为12.5 mg/kg。6种类型固体废物样品的加标回收率在90.4%~110.0%之间,测定结果的相对标准偏差为2.3%~4.6%(n=6)。该方法样品预处理简单、重现性好、检出限低,适用于多种固体废物中总氟的测定。     

二氧化碳和丙烯直接合成甲基丙烯酸的NiPMo/TiO2催化剂的研究

用溶胶-凝胶法以磷钼酸(MPA)的镍盐溶液水解钛酸四丁酯制备了NiPMo/TiO2催化剂.使用ICP、 XRD、 TG-DTA、 IR、 TPD-MS和微反应技术研究了催化剂的化学组成、热稳定性、化学吸附性质和催化反应性能.杂多钼酸盐与TiO2通过O2-在TiO2表面发生了键合.在623 K下,杂多阴离子仍保持原有的Keggin结构.CO2在Lewis酸位Ni(Ⅱ)和Lewis碱位Ni-O-Mo的桥氧协同作用下生成CO2卧式吸附态Ni(Ⅱ)←O-(CO)←(O--Ni).丙烯有多种吸附态在催化剂上吸附.在563 K、 1 MPa和空速1500 h-1的反应条件下,丙烯的摩尔转化率为3.2%,产物MAA选择性为95%.     

Synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives

Different approaches for the synthesis of 1-benzyloxypyrazin-2(1H)-one derivatives from simple amino acids have been investigated. A library of 33 precursors for the preparation of N-hydroxy pyrazinones was obtained in moderate to good yields.     

Toward new camptothecins. Part 6: Synthesis of crucial ketones and their use in Friedländer reaction

In the context of the preparation of camptothecin and luotonin A analogs, the synthesis of some key keto-precursors and their use in Friedländer condensation are described. This paper also focuses on the stability of these keto intermediates and emphasizes the major differences between indolizinones and pyrroloquinazolinones series. Noteworthy is also the report of some original structures isolated as by-products of some experiments.     

CoFe2O4自形成磁性液体场致结构化对磁化的影响

The Langevin paramagnetic theory can’t describe the relation between magnetization of ferrofluids and applied magnetic field. The structuralization of ferrofluids, which is considered the main influence factor of the magnetization, is regarded. The part of magnetization works is deposited when the structure is forming. This action influences the magnetization of ferrofluids directly or indirectly. On the base of the “compressing” model, the Langevin function that usually describes the magnetization of ferrofluid is modified, and a well-fitted curve is obtained. An equation of the relation between the equivalent volume fraction after being “compressed” and the intensity of magnetic field is discovered, which approximately describes the process of magnetization. The relation between the approximate initial susceptibility and the volume fraction can be obtained from modified formula.     

Highly regioselective Buchwald–Hartwig amination at C-2 of 2,4-dichloropyridine enabling a novel approach to 2,4-bisanilinopyridine (BAPyd) libraries

The highly regioselective Buchwald–Hartwig amination at C-2 of the cheap and readily accessible reagent, 2,4-dichloropyridine with a range of anilines and heterocyclic amines is described. This new methodology is robust and provides a facile access to 4-chloro-N-phenylpyridin-2-amines on 0.25 mol scale. These intermediates undergo a further Buchwald–Hartwig amination at higher temperature to enable rapid exploration of the chemical space at C-4 and to provide a library of 2,4-bisaminopyridines.     

KMnO4-mediated oxidative CN bond cleavage of tertiary amines: Synthesis of amides and sulfonamides

KMnO₄-mediated oxidative CN bond cleavage of tertiary amines producing secondary amine was introduced, which was trapped by electrophiles (acyl chloride and sulfonyl chloride) to form amides and sulfonamides. The reaction could take place at mild condition, tolerating a wide range of function groups and affording products in moderate to excellent yields.     

Chemistry of heterocyclic compounds at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences, over 50 years (Review)

The review contains a concise historical account and information on the most significant researches undertaken by the staff at the A. E. Favorsky Irkutsk Institute of Chemistry, Siberian Branch of the Russian Academy of Sciences on the Chemistry of Heterocyclic Compounds. Dedicated to Academician of the Russian Academy of Sciences B. A. Trofimov on his 70th jubilee. Translated from Khimiya Geterotsiklicheskikh Soedinenii, No. 10, pp. 1443–1502, October, 2008.     

A general and convenient synthesis of 4-(tosylmethyl)semicarbazones and their use in amidoalkylation of hydrogen,heteroatom, and carbon nucleophiles

A general synthesis of previously unknown semicarbazone-based α-amidoalkylating reagents, 4-(tosylmethyl)semicarbazones, has been developed. The synthesis involved three-component condensation of semicarbazones of aliphatic or aromatic aldehydes with the same or other aldehydes and p-toluenesulfinic acid. The scope and limitations of this reaction were investigated. The compounds obtained were demonstrated to be an efficient α-(4-semicarbazono)alkylating agents. They were reacted with H- (sodium borohydride), O- (sodium methylate), S- (sodium phenylthiolate), N- (pyrrolidine, sodium succinimide), P- (trialkyl phosphites), and C-nucleophiles (sodium diethyl malonate) to give the corresponding products of the tosyl group substitution, 4-substituted semicarbazones, including analogues of nitrofurazone. Among the prepared compounds tested in vitro for antibacterial and antifungal activity, three nitrofuryl-containing semicarbazones exhibited high biological activities with minimum inhibitory concentration (MIC) values of 8–32 μg/mL.     

Sulfur-directed metal-free and regiospecific methyl C(sp3)–H imidation of thioanisoles

Regiospecific and direct imidation of the methyl C(sp³)–H bond of thioanisoles is realized under mild and metal-free conditions with N-fluorobis(benzenesulfonyl)imide as an oxidant and nitrogen source. Proposed mechanism suggests that thionium ion intermediates and a Pummerer-type reaction are involved. The imidation has advantages such as high step-economy, excellent functionality tolerance, and regiospecificity, giving structurally diverse imidation products.     

Synthesis of novel chiral bidentate hydroxyalkyl-N-heterocyclic carbene ligands and their application in palladium-catalyzed Mizoroki–Heck couplings and asymmetric addition of diethylzinc to benzaldehyde

A small library of new chiral bidentate hydroxyalkyl-imidazolium salts 1 is conveniently synthesized on multi-gram scale from inexpensive and commercially available chiral pool amino acids. The corresponding carbenes, generated by deprotonation of imidazolium salts 1, in combination with palladium(II) chloride were tested in the Mizoroki–Heck coupling reaction. The most significant results in terms of yields and reactivities were achieved with low catalyst loading. The catalytic activities of these imidazolium salts were also investigated in the asymmetric addition of diethylzinc to benzaldehyde. The use of MgO nanoparticles as an additive in conjunction with these ligands played a crucial role in increasing the efficiency of these reactions.