热水解离子色谱法测定岩石样品中的氯和硫

研究开发了一种热水解离子色谱法测定岩石样品中的氯和硫的方法技术。所研究开发的方法具有灵敏、高效、无干扰和准确的特点。实验研究和选择了热水解离子色谱测定的最佳工作条件。用测定的方法对6个国家一级岩石地球化学标准物质GSR1－6进行了分析测定，并在研究我国东部上地壳区域元素丰度实践中测定了2000件岩石样品。测定结果表明，测定值与标准物质的标准值一致。该方法的检出限分别国；氯31×10^-6。方法的精密度（RSD，％）对氯含量水平为40×10^-6，硫酸根含量水平180×10^-6时分别为6.1%和3.0%。     

微量元素对B族维生素同步荧光分析法影响的研究

本文探讨了钙、镁、铜等 7种微量元素对维生素 B1、B2 、B6的同步荧光光谱的影响。实验结果表明 ,当Ca2 + 的浓度为 1.0× 10 -3mol/ L时 ,VB2 、VB6的同步荧光光谱有显著的增强作用 ;而其他微量元素对VB1、VB2 、VB6的同步荧光有不同程度的猝灭或增强作用。利用 Ca2 + 对 3种维生素荧光强度的增敏作用 ,可以有效地提高同步荧光分析法同时测定 VB1、VB2 、VB6的灵敏度 ,VB1、VB2 、VB6的校准曲线的线性范围分别为 2 .4× 10 -7— 9.0× 10 -6、1.1× 10 -7— 4 .6× 10 -6、7.1× 10 -7— 2 .0× 10 -6mol/ L。采用本方法测定混合样品 ,样品不需分离 ,操作简便、快速     

ICP-MS法测定人体器官中Cs,Th和U的分布

采用ICP-MS对10种人体器官组织样品中的痕量Cs, Th和U进行了研究, 选择了最佳仪器工作参数, 用Rh为内标元素补偿基体效应和灵敏度漂移, 检出限为Th 5.7×10-3, U 1.04×10-2, Cs 1.78×10-2 ng·mL-1. 随同样品分析了NIST SRM 8414牛肌肉和NIST SRM 1486骨粗粉标准参考物质, 测得值与标准参考值吻合. 用HNO3和HClO4混合酸消解样品, 不须分离富集, 直接对人尸体的肺、肝、骨胳、甲状腺、小肠、胃、肌肉、肾、脾和心脏中痕量Cs, Th和U进行测定. 结果表明 ICP-MS方法可以准确、精密地测定人体器官中的微量Cs, Th和U; 这3个元素在人体各个器官的分布各异, 例如Th和U主要分布在肺和肾, 而Cs则在全身相对均匀分布; 来自不同省市的肺部Cs, Th和U含量之间具有显著性差异, 且同一地区人肺样品中的Cs, Th和U浓度呈现同升共降的趋势, 说明Cs, Th和U在人体器官的积蓄和各地的环境、饮食相关.     

氢化物发生-原子荧光法直接测定锑及其化合物中的硒和铋

通过研究在不同酸度下Sb5+对Se,Bi的干扰情况,发现在高酸度下,Sb对Se,Bi的干扰明显减弱,并结合锑在不同价态发生氢化反应的差异性,建立了不需通过任何化学分离而直接测定锑及其相关产品中的微量硒和铋的方法,并用于实际样品的分析.方法对实际样品加标回收率在95%～105%之间,检测下限(含量)硒和铋分别为0.00004×10-2mg@L-1和0.0001×10-1mg@L-1,对实际样品分析精度分别为RSD(Se)=2.4%(含量为0.00169×10-2mg@L-1时),5.4%(含量为0.00056×10-mg@L-1时)和RSD(Bi)=5.0%(含量为0.00024×10-2mg@L-1时),1.3%(含量为0.00229×10-2mg@L-1时),完全满足实际样品分析的要求.     

分光光度法测定中草药中的槲皮素

在表面活性剂 Triton X- 10 0的存在下 ,于 p H4 .5 HAc- Na Ac缓冲溶液介质中 ,槲皮素与镓形成 2∶ 1的黄色络合物 ,由此建立了用分光光度法测定中草药中槲皮素含量的新方法。槲皮素的检出限为1.2 6× 10 -7mol· L-1,线性范围为 6 .30× 10 -7— 1.86× 10 -6mol· L-1,RSD<4 .1%。与 AFS法比较测定结果一致     

荧光光度法测定蜂胶中黄酮

研究了用荧光光度法测定蜂胶中黄酮。以芦丁为标准样品 ,以 4 33nm和 4 95nm为激发和发射波长 ,测定了蜂胶中总黄酮含量。回归方程式为 y=2 .9618+0 .7599× 10 -3x,相关系数 r=0 .9987。方法简便、快速、准确。     

极谱分析法连续测定痕量铅和镉

研究了 Pb2 + 和 Cd2 + 与 KCl-酒石酸钠 -三乙醇胺 -明胶体系的二次导数极谱波。在 p H=4 .5的 HAc-Na Ac介质中 ,Pb2 + 和 Cd2 + 分别于 - 0 .4 6 V和 - 0 .6 4V电位处产生一良好的极谱波。峰电流与 Pb2 + 和Cd2 + 的浓度分别在 1× 10 -5— 3× 10 -1g· L-1和 5× 10 -5— 6× 10 -3 g· L-1范围内呈线性关系。 Pb2 + 和Cd2 +的检出限分别为 1× 10 -7g·L-1和 5× 10 -7g·L-1。本法准确、简便、快速、选择性高。已直接用于饮料中铅和镉的连续测定 ,同时也对酒及面粉样品进行了测定 ,回收率分别为 99.9%— 10 0 .1%和 97.0 %—10 4 .8%。     

Rb（5PJ）＋Rb（5PJ）→Rb（5JS）＋Rb（nl=5D，7S）碰撞能量合并

研究了Rb(5PJ)+Rb(5PJ)→Rb(nlJ')+Rb(5S)碰撞能量合并过程,利用单模半导体激光器分别共振激发Rb原子的5P1/2或5P3/2态,利用另一与泵浦激光束反向平行的单模激光束作为吸收线探测激发态原子密度及其空间分布,吸收线分别调至5P1/2→5D3/2和5P3/2→7S1/2跃迁.由激发态原子密度和谱线荧光比得到碰撞能量合并过程的截面,对5P3/2激发,碰撞转移得到5D5/2,5D3/2和7S1/2的截面分别是(1.32士0.59)×10-14,(1.18士0.53)×10-14和(3.21士1.44)×10-15cm2;对5P1/2激发,碰撞转移到5D5/2和5D3/2的截面分别是(6.57士2.96)×10-15和(5.90士2.66)×10-15cm2.与其他的实验结果进行了比较.     

微波消化-分光光度法测定烟草中的镁

研究了偶氮氯膦 - 与镁的显色反应 ,在 p H=10 .0硼砂 -氢氧化钠缓冲介质中 ,偶氮氯膦 - 与镁反应生成 1∶ 1稳定的络合物 ,λmax=6 10 nm,ε=2 .34× 10 4L· mol-1· cm-1。镁含量在 0— 15μg/ 2 5 m L范围内符合比耳定律 ,结合微波消化样品技术 ,建立了一种烟草样品中镁含量的测定方法 ,结果令人满意     

EPR——标准样品

SAMPLE No. SPI NS EPR SPECTR 2 MMnS01·H20M1—3×10z‘M2—1×102。M3—5x10”M·～j9×10“M5—6×10¨M 6—1×101 0M.一一5×10’7 VOS04·×H20公/ f/ 缨 \/蓦V2--薰10~1--5 x 101"102 10i1 lO i誓二 1× ¨ / \汇。锄。√/\ ’.一V5—6ר I /V 6～× ¨ \ / .V,一×’。 V —G值△Hp~(G)2.004土0.001 204±11.977土0.001130±lEPR——标准样品…     

Guided-Wave Two-Dimensional Acousto-Optic Scanner Using Proton-Exchanged Lithium Niobate Waveguide

Two-dimensional scanning of a 0.6328 mum guided-light beam has been realized using noncolinear acousto-optic (AO) coplanar Bragg diffraction together with colinear AO guided-mode to substrate radiation-mode conversion in a Z-cut Xpropagation LiNbO3 proton-exchanged (PE) waveguide. The two surface acoustic (SAW) waves utilized are at the center frequencies of 500 and 200 MHz, propagating in the Y and X axes, respectively. Two-dimensional scanning of approximately 720 resolvable light beam spots, namely, 18 40 (horizontal vertical) scanning, has been demonstrated using a light beam of 1.0 mm aperture. The total number of resolvable beam spots can be greatly increased from 720 by simply utilizing SAW transducers of larger bandwidth and a light beam of greater aperture. It should also be possible to significantly increase the diffraction efficiency from 3 % by optimizing the parameters of the PE waveguide and the SAWs.     

Effect ofγ-radiation on the spectral luminescence characteristics of impure cadmium tungstate crystals

Results of a study of the effect of γ-radiation on the spectral luminescence properties of cadmium tungstate crystals doped with silver, bismuth, and molybdenum cations are presented. Spectral characteristics of the nondnnnoped crystals are briefly described. Absorption and photo and X-ray luminescence spectra of the crystals taken before and after exposure to γ-radiation (5.5·10⁴ Gy) are compared. It is found that the spectral characteristics of the crystals doped with silver, bismuth, and molybdenum cations do not change markedly after the exposure. The relation between the type of impurity-induced defects, individual characteristics of the impurity cations, and the character of the effect of γ-radiation on the spectral luminescence properties of impure crystals is analyzed (preliminarily). Translated from Zhurnal Prikladnoi Spektroskopii, Vol. 64, No. 1, pp. 55–60, January–February, 1997.     

Femtosecond Transform-Limited Pulse Generation by Compensating for the Linear Chirp of SPM Spectra in Dispersion Shifted Fibers

A simple technique of pulse compression, based on the linear chirp compensation of self-phase modulation (SPM) spectra in dispersion shifted fibers, is demonstrated. The optimization procedure is carried out, for a short span of a single-mode fiber, using a parabolic law, which describes the behavior of the squared output pulse width versus the pump peak power in the case of Gaussian pulses. The experimental results give a minimum pulse duration of 233 fs, which is in good agreement with the model. Shorter and coherent pulses, down to 90 fs, have been obtained by inserting an interference filter at the optical output.     

Sorting of bending magnets for the SSRF booster

The Shanghai Synchrotron Radiation Facility(SSRF)booster ring,a full energy injector for the storage ring,is deigned to accelerate the electron beam energy from 150MeV to 3.5GeV that demands high extraction efficiency at the extraction energy with low beam loss rate when electrons are ramping.Closed orbit distortion(COD)caused by bending magnet field uniformity errors which affects the machine performance harmfully could be effectively reduced by bending magnet location sorting.Considering the affections of random errors in measurement,both ideal sorting and realistic sorting are studied based on measured bending magnet field uniformity errors and one reasonable combination of bending magnets which can reduce the horizontal COD by a factor of 5is given as the final installation sequence of the booster bending magnets in this paper.     

Measurement of nonlinear coefficient of optical fiber based on small chirped soliton transmission

We measure the waveform and phase curves of short optical pulses before and after transmission over different lengths of fibers by use of the pulse analyzer with the frequency-resolved optical gating (FROG),and numerically simulate pulse evolution under the experimental conditions.The nonlinear coefficient of the fiber is given by comparing the experimental results with the numerical ones.Difference between the experiment and numerical simulation is analyzed.     

Resonance scattering of canonical elastic shells in absorbing fluid medium

Resonance scattering of elastic spherical shell and cylindrical shell while the surrounding fluid medium has absorption is studied. The normal mode solution derived using exact elastic theory and the separation of variables is still applicable. However, the scattering form function has to be modified for the absorbing medium, otherwise the unreasonable result would be obtained. The backscattering form function in the absorbing medium is redefined, and the form function of elastic spherical and cylindrical shell with vacuum or solid matter filled is calculated in various absorption conditions. The results show that the absorption of surrounding fluid leads to notable attenuation of the coincidence resonances in the mid-frequency, but it has a little influence on the low-frequency resonance scattering induced by the filler inside the shell.     

Single-beam self-referenced phase-sensitive surface plasmon resonance sensor with high detection resolution

A versatile and low-cost single-beam self-referenced phase-sensitive surface plasmon resonance(SPR)sensing system with ultra-high resolution performance is presented.The system exhibits a root-mean-square phase fluctuation of ±0.0028.over a period of 45 min.i.e.a resolution of±5.2×10-9 refractive index units.The enhanced performance has been achieved through the incorporation of three design elements:a true single-beam configuration enabling complete self-referencing so that only the phase change associated with SPR gets detected,a differential measurement scheme to eliminate spurious signals not related to the sensor response,and the elimination of retardation drifts by incorporating temperature stabilization in the liquid crystal phase modulato .Our design should bring the detection sensitivity of non-labeling SPR biosensing closer to that achievable by conventional fluorescence-based techniques.     

Influences of SiO2 protective layers and annealing on the laser-induced damage threshold of Ta2O5 films

Ta2O5 films are prepared on BK7 substrates with conventional electron beam evaporation deposition.The effects of SiO2 protective layers and annealing on the laser-induced damage threshold (LIDT) of the films are investigated.The results show that SiO2 protective layers exert little influence on the electric field intensity(EFI)distribution,microstructure and microdefect density but increase the absorption slightly.Annealing iS effective on decreasing the microdefect density and the absorption of the films.Both SiO2 protective layers and annealing are beneficial to the damage resistance of the films and the latter is more effective to improve the LIDT.Moreover,the maximal LIDT of Ta2O5 films is achieved by the combination of SiO2 protective layers and annealing.     

A stereo matching algorithm using multi-peak candidate matches and geometric constraints

Gray cross correlation matching technique is adopted to extract candidate matches with gray cross correla- tion coefficients less than some certain range of maximal correlation coefficient called multi-peak candidate matches. Multi-peak candidates are extracted corresponding to three closest feature points at first. The corresponding multi-peak candidate matches are used to construct the model polygon. Correspondence is determined based on the local geometric relations between the three feature points and the multi-peak candidates. The disparity test and the global consistency checkout are applied to eliminate the remaining ambiguous matches that are not removed by the local geometric relational test. Experimental results show that the proposed algorithm is feasible and accurate.