钨酸铋对四环素光催化降解性能

采用水热法制备了钨酸铋催化剂,以空气为氧化剂,四环素为底物,考察了制备催化剂时溶液的酸度、降解反应时不同光源、光强度和催化剂量对钨酸铋的光催化降解四环素性能的影响.结果表明,当制备钨酸铋催化剂溶液的pH为1时,催化降解效果较好;当催化剂与四环素的物质的量之比为0.3∶1时,光照时间100 min,光催化降解率达66%;以钨酸铋为催化剂,太阳光光催化降解性能优于红外光和紫外光,太阳光强度越强,催化降解效果越好.     

Fe3O4@Ce掺杂ZnO光催化降解罗丹明B

通过共沉淀法优化制备了Fe_3O_4为内核的磁性核壳式Ce掺杂ZnO催化剂(Fe_3O_4@ZnO-Ce),考察催化剂的稳定性和适用性,利用SEM、BET、ICP-AES、XRD、UV-Vis DRS、VSM、FT-IR等手段对催化剂进行表征,研究温度、pH、催化剂投加量对罗丹明B降解率的影响。结果表明,Ce掺杂ZnO包覆在Fe_3O_4表面形成球状纳米颗粒,平均粒径约100 nm,Fe_3O_4和3%Ce掺杂ZnO最佳物质的量之比为1:20,400℃煅烧2 h。日光模拟灯为光源,在pH为7、水温30℃、催化剂投加量0.2 g/100 mL、90 min罗丹明B降解率达到92%,6次循环套用降解率达到53%以上。     

玻璃管负载纳米TiO2薄膜的制备及其对乙烯降解的研究

采用sol—gel技术，在细玻璃管表面制备了La掺杂复合TiO2薄膜，采用封闭循环装置考察了催化剂负载质量、镧掺杂量、热处理温度和湿度等因素对催化活性的影响．结果表明，随着薄膜层数的增加，乙烯降解率增加，UV-VIS在近紫外的吸收随层数的变化与之吻合；镧掺杂量为1.5％、热处理温度500℃催化剂活性最高，而湿度的增大有利于提高乙烯的降解率和降解速度．     

铋掺杂介孔二氧化钛的制备及光催化动力学

以介孔分子筛(KIT-6)为载体,采用溶液浸渍法合成了铋(Bi)掺杂的介孔二氧化钛(TiO₂)光催化剂。利用XRD、TEM、SEM、XPS、N₂吸附-脱附法和拉曼光谱法等技术手段对材料的结构和形貌进行表征。通过紫外-可见吸收光谱法考察了催化剂对罗丹明B光催化降解效率,进一步考察了Bi的掺杂量对光催化反应速率的影响,并对光催化降解动力学进行了初步研究。结果表明,Bi掺杂的介孔TiO₂具有较窄的孔径分布(3~4 nm),而且吸收范围扩展到可见光区,其光催化活性明显高于商品TiO₂(P25)。随之Bi掺杂量的提高,反应速率常数也增大,其光催化降解罗丹明B的反应均符合准一级动力学方程。     

掺杂型稀土双钙钛矿光催化剂La2FeTiO6葡萄糖络合法制备与表征

采用葡萄糖络合法制备了双钙钛矿型催化剂La2FeTiO6,进行不同量Sr掺杂改性。利用X射线粉末衍射(XRD)、H2-程序升温还原(H2-TPR)、比表面(BET)、扫描电镜(SEM)、磁性与电性测试等手段对其进行表征,以可见光催化降解对氯苯酚为探针讨论了Sr掺杂对La2FeTiO6催化剂的物理化学性质及可见光催化活性的影响。结果表明:催化剂La2FeTiO6在掺杂Sr后,催化剂的可见光催化活性均有所提高,其中Sr掺杂量为0.08时,催化剂的光催化活性提高最大,光照1 h时对氯苯酚的降解率就已经达到了90%,5 h后降解率达到99.2%。La2FeTiO6通过Sr掺杂改性后光照5 h降解率提高了37.1%。比表面测试和程序升温还原试验结果表明,碱土金属Sr的掺杂提高了催化剂的比表面,促进了双钙钛矿La2FeTiO6中Fe的还原,使其还原峰面积增大,还原温度也有所降低。电性和磁性测量结果说明,碱土金属Sr的掺杂明显影响其催化剂的电磁性能。     

Ho3+掺杂铁酸铋的制备及光催化性

为提高铁酸铋磁性和光催化性能,通过低温热分解前驱体快速制备出可磁分离回收的Ho³⁺掺杂铁酸铋复合物Bi_0.95Ho_0.05FeO₃纳米颗粒,并用X粉末衍射仪(XRD)、傅里叶红外变换光谱仪(FT-IR)、紫外可见漫反射光谱仪(DRS),磁强计(VSM)和Zeta电位仪等多种手段对物相和性质进行表征,同时以甲基橙(MO)为降解模型,考察溶液的酸碱性和常见无机阴离子共存下其光催化性能。 结果显示,产物以R3c相铁酸铋为主,带隙为1.90 eV,Ho³⁺掺杂后使铁酸铋的磁性增强了4倍,催化性能提高30%。 而该催化剂的催化性能受降解溶液本身酸碱性以及共存阴离子的氧化性与酸碱性的影响。 另外,对该催化剂的回收也进行了研究。 结果表明,所得催化剂可通过磁分离回收,从而反复利用。     

CeO2添加量对催化剂Cu-Ni-Ce／SiO2性能的影响

采用浸渍法在不同Ce掺杂量时制备了用于湿式H2O2降解吡虫啉农药废水的Cu-Ni-Ce/SiO2催化剂, 利用BET、 SEM、 XRD和XPS等对其进行了表征, 并研究了Ce掺杂量对催化剂表面形态的影响以及催化剂表面形态与活性及稳定性之间的关系.结果表明: 适量添加Ce后, 催化剂晶粒尺寸减小, 比表面积增加, Cu、 Ni固溶体量和催化剂表面化学吸附氧量增加, 而且活性组分的分散性增加. 湿式H2O2降解吡虫啉农药废水时, 在催化剂用量10 g/L、反应温度110 ℃、双氧水用量为理论需用量、进水pH为9.0、反应60 min条件下, 0.16%Ce掺杂量的Cu-Ni-Ce/SiO2的催化剂的活性比相同工艺条件的无Ce添加的催化剂活性提高了7.2%, 活性组分溶出量也大为减少.     

La和Zn掺杂铌酸铋的光催化降解性能及其机理

用化学共沉淀法制备了镧和锌掺杂的铌酸铋纳米颗粒,表征了制备样品的微观结构和光催化降解性能。结果表明制备的样品对RhB表现出良好的可见光催化降解活性,且光催化效果受各种因素的影响。其中,Bi_0.96La_0.04NbO₄用量为0.15 g时,对pH=4、50 mL浓度为5 mg·L^-1 RhB溶液的光催化效果最佳。光催化机理研究表明催化剂在可见光照射下产生的电子空穴对RhB的降解起主要作用。该催化剂的制备方法简单、光催化性能稳定,5次循环后的活性仍大于95%。     

Ni^2＋／TiO2介孔材料光催化降解造纸废水影响因素的研究

溶胶-凝胶法合成了不同Ni掺杂量的Ni2 /TiO2介孔复合材料.用X射线衍射(XRD)、透射电子显微镜(TEM)、红外(FT - IR)光谱和N2吸附脱附等对产物结构进行了表征.考察了Ni掺杂量、催化剂的用量、初始pH、外加氧化剂等因素对光催化降解造纸废水的影响.结果表明: Ni2 /TiO2介孔复合材料光催化降解造纸废水的最佳反应条件为:Ni掺杂量为2%、催化剂用量1.5g/L、初始pH=4、通氧;光照4 h后,废水色度去除率达100%; 12 h后,废水CODCr去除率达到83.4%.     

微波助离子液体中锌和氮共掺杂TiO2催化剂的制备及微波强化光催化氧化活性

在1-丁基-3-甲基咪唑六氟磷酸盐（[Bmim]PF6）离子液体介质中,采用微波干燥的方法制备了锌和氮共掺杂的TiO2催化剂TiO2-Zn-N,分别采用IR、XRD、SEM、BET对催化剂结构进行了测试和表征。室温条件下,以甲基橙和苯酚溶液为模拟污染物,在微波超声波组合催化合成仪中,分别利用微波辐射（MW）、紫外光照（UV）、微波辐射-紫外光照（MW-UV）和太阳光照射（SL）等降解方式,着重考察了制备条件对TiO2-Zn-N光催化活性的影响。结果表明,在离子液体用量为5.6 mL、Zn掺杂量n(Zn)/n(Ti)=0.015:1、N掺杂量n(N)/n(Ti)=4:1、微波干燥功率350 W、微波干燥时间20 min、煅烧温度700 ℃、煅烧时间2 h的条件下所制得的TiO2-Zn-N催化剂具有较高的光催化活性;在MW、UV、MW-UV和SL四种降解条件下,TiO2-Zn-N对甲基橙的降解率分别为29.6%、95.4%、99.2%和79.2%;并且在前三种降解条件下,甲基橙降解率始终是：MW-UV> UV> MW。这表明在紫外光照条件下,微波辅射具有强化催化剂降解甲基橙的作用。     

碲铋渣中铋的测定

讨论了在pH=9.4～10.0的氨性溶液中,利用Fe3+与Te4+、Bi3+生成三元共沉淀物,分离其它杂质,然后用KOH溶解Te,从而达到Te,Bi分离的目的。在pH=1.5～1.7的溶液中,利用抗坏血酸掩蔽铁,以硫脲-PAR作为指示剂,用EDTA标准溶液滴定Bi。当n=6时,相对标准偏差为0.4%,回收率为98.53%～102.2%,方法准确、可靠。     

Cu2+掺杂的Bi2O3的制备及光催化性能的研究

本文采用并流沉淀法制备了Cu2+掺杂的纳米Bi2O3光催化剂(Cu/Bi原子比分别为1%,2%,3%和4%)。以甲基橙模拟有机污染物对催化剂的光催化性能进行了考察。用比表面(BET)、X-射线粉末衍射(XRD)、X-射线光电子能谱(XPS),紫外-可见漫反射光谱(DRS)和表面光电压谱(SPS)对所制备的催化剂进行了表征。结果表明,Cu2+掺杂量为3%时制备的Bi2O3具有最高的比表面积、孔容、最小孔径和晶粒尺寸。对甲基橙的光催化脱色结果显示掺杂量为3%时Cu2+-Bi2O3表现出最佳的光催化活性。     

铋系超导体组成分析

本文首次提出了一种离子交换柱分离——滴定法测定Bi系超导体中Bi、Pb、Cu、Ca和Sr含量的方法。研究了进样条件和淋洗方法,特别是Bi~(3+)在微酸性溶液中的亚稳态进样。测定合成样品时,Bi、Pb、Cu、Ca和Sr的相对标准偏差分别为0.7％、1.6％、0.5％、0.4％和0.2％。分析了超导体样品,并测定了其中Cu~(3+)。     

不对称变色酸双偶氮衍生物与某些非稀土元素的显色反应及其应用研究 Ⅲ:偶氮氯膦-pN与铋(Ⅲ)的β型反应的研究

本文报道铋(III)与不对称变色酸双偶氮衍生物之间的一类特殊反应──β型反应, 研究了试剂分子结构与反应性能的关系, 着重探讨铋(III)与偶氮氯膦-pN的β-型反应行为, 在高氯酸介质中, 铋(III)与上述试剂形成灵敏度很高的稳定β型配合物, λmax=713nm, εmax=9.84×10^4L·mol^-^1·cm^-^1, 并考察了反应酸度、显色剂浓度、有机溶剂(或表面活性剂)、显色温度及显色时间等对反应的影响, 测定了α和β型配合物的组成, 初步探索了α和β型配合物之间相互转化的规律。     

单掺杂与共掺杂离子对Sr2Mg(BO3)2磷光体热释发光的影响

通过高温固相法合成了Sr2Mg(BO3)2磷光体, 并研究了Li＋, Bi3＋, Gd3＋, Ti4＋共掺杂对Sr2Mg(BO3)2∶Dy磷光体热释发光的影响. 研究发现: Li＋的共掺杂使Sr2Mg(BO3)2∶Dy磷光体的热释光主峰强度增加, 而 Bi3＋, Gd3＋或Ti4＋的掺入使样品的热释光强度降低. 在Li＋, Bi3＋, Gd3＋或Ti4＋共掺杂的Sr2Mg(BO3)2∶Dy磷光体高温热释光发射谱中, 我们观察到了480, 579, 662和755 nm的发射峰, 为特征Dy3＋离子的4F9/2→6H15/2, 4F9/2→6H13/2, 4F9/2→6H11/2和4F9/2→6H9/2跃迁, 与Sr2Mg(BO3)2∶Dy磷光体的发射一致. 利用峰形法, 我们评估了Sr2Mg(BO3)2∶ , ( )热释光磷光体234 ℃发光峰的动力学参数, 陷阱深度E＝1.1 eV, 频率因子s＝6.3×109 s－1, 遵循二级动力学.     

Bi掺杂NaTaO3中Bi的化学价态对其光催化性能的影响

分别采用NaBiO3和Bi(NO3)3为Bi源制备了Bi掺杂NaTaO3光催化剂,研究了Bi离子的价态对NaTaO3光催化分解水制氢性能的影响.采用X射线衍射(XRD)、拉曼光谱、X射线光电子能谱(XPS)和紫外-可见吸收光谱研究了催化剂的晶体结构、Bi离子的化学状态和催化剂的光学吸收性能.以光催化分解水制氢反应研究了Bi离子掺杂NaTaO3的催化性能. XRD结果表明,对于两个不同Bi源掺杂的NaTaO3样品, Bi离子的掺杂没有改变催化剂的单斜相结构,但拉曼光谱证实Bi离子的掺杂致使Ta–O–Ta键角偏离了180o. XPS结果表明,以Bi(NO3)3为Bi源时, Bi离子以Bi3+掺杂于NaTaO3的A位;当以NaBiO3为原料时, Bi3+和Bi5+共掺杂于NaTaO3的A位.两种不同Bi源掺杂得到的样品在紫外-可见吸收光谱中给出了相似的光学吸收,但Bi3+的掺杂对NaTaO3光催化性能影响不大,而Bi3+和Bi5+共掺杂大大提高了NaTaO3的光解水制氢性能. Bi离子取代Na离子在A位的掺杂,在NaTaO3结构中引入了能够促进载流子分离的空位和缺陷;与此同时, Bi的掺杂导致Ta–O–Ta键角偏离180o而不利于载流子迁移.对于Bi3+掺杂的NaTaO3样品,这两种作用相互抵消,使得其催化性能与NaTaO3相比没有变化;而Bi3+和Bi5+的共掺杂和高价态Bi5+的掺杂引入了更多的空位和缺陷,提高了光生电子-空穴的分离效率,从而提高了光催化产氢性能.研究表明,光催化过程中载流子的迁移是影响催化性能的重要因素,而在ABO3钙钛矿结构的A位引入高价态离子是促进光生载流子分离的有效途径.     

Effect of bismuth oxide on the thermal stability and Judd-Ofelt parameters of Er3+/Yb3+ co-doped aluminophosphate glasses

The Er3+/Yb3+ co-doped glasses with compositions of xBi2O3-(65-x)P2O5-4Yb2O3-11Al2O3-5BaO-15Na2O (where x=0, 2.5, 5, 7.5 and 10 mol%) were prepared using the normal melt quench technique. The optical absorption spectra of the glasses were recorded in the wavelength range 300-1700 nm. The effect of Bi2O3 content on the thermal stability and absorption spectra of glasses was investigated. In addition, the Judd-Ofelt parameters and oscillator strengths were calculated by employing Judd-Ofelt theory. It was observed that the positions of the fundamental absorption edge and cut-off wavelength shifted towards red as the content of Bi2O3 increased. However, there were no red shifts found both in the peak wavelength and in the center of mass wavelength of all absorption bands with Bi2O3 content increasing. The results of Judd-Ofelt theory analysis showed that Judd-Ofelt parameters Omega t (t=2, 4, 6) changed sharply when Bi2O3 concentration exceeded 5 mol%. The variation trends of experimental oscillator strength were similar with those of Judd-Ofelt parameters as function of Bi2O3 concentrations. Moreover, differential scanning calorimetry experiments showed that the increases of Bi2O3 content weakened the network structure and then lowered the thermal stability of the glasses. The spontaneous emission probability A rad, branching ratio beta and the radiative lifetime tau rad were also calculated and analyzed. The stimulated emission cross-section of Er3+ was calculated according to the McCumber theory. It was found that the stimulated emission cross-section of Er3+ was monotonically increases with Bi2O3 content increasing.     

Optimization of a single-drop microextraction method for multielemental determination by electrothermal vaporization inductively coupled plasma mass spectrometry following in situ vapor generation

A headspace single-drop microextraction (HS-SDME) method has been developed in combination with electrothermal vaporization inductively coupled plasma mass spectrometry (ETV-ICP-MS) for the simultaneous determination of As, Sb, Bi, Pb, Sn and Hg in aqueous solutions. Vapor generation is carried out in a 40 mL volume closed-vial containing a solution with the target analytes in hydrochloric acid and potassium ferricyanide medium. Hydrides (As, Sb, Bi, Pb, Sn) and Hg vapor are trapped onto an aqueous single drop (3 µL volume) containing Pd(II), followed by the subsequent injection in the ETV. Experimental variables such as medium composition, sodium tetrahydroborate (III) volume and concentration, stirring rate, extraction time, sample volume, ascorbic acid concentration and palladium amount in the drop were fully optimized. The limits of detection (LOD) (3σ criterion) of the proposed method for As, Sb, Bi, Pb, Sn and Hg were 0.2, 0.04, 0.01, 0.07, 0.09 and 0.8 µg/L, respectively. Enrichment factors of 9, 85, 138, 130, 37 and 72 for As, Sb, Bi, Pb, Sn and Hg, respectively, were achieved in 210 s. The relative standard deviations (N = 5) ranged from 4 to 8%. The proposed HS-SDME-ETV-ICP-MS method has been applied for the determination of As, Sb, Bi, Pb, Sn and Hg in NWRI TM-28.3 certified reference material.     

Flow injection determination of bismuth in urine by successive retention of Bi(III) and tetrahydroborate(III) on an anion-exchange resin and hydride generation atomic absorption spectrometry

Bismuth as BiCl₄⁻ and BH₄⁻ ware successively retained in a column (150 mm × 4 mm, length × i.d.) packed with Amberlite IRA-410 (strong anion-exchange resin). This was followed by passage of an injected slug of hydrochloric acid resulting in bismuthine generation (BiH₃). BiH₃ was stripped from the eluent solution by the addition of a nitrogen flow and the bulk phases were separated in a gas–liquid separator. Finally, bismutine was atomized in a quartz tube for the subsequent detection of bismuth by atomic absorption spectrometry. Different halide complexes of bismuth (namely, BiBr₄⁻, BiI₄⁻ and BiCl₄⁻) were tested for its pre-concentration, being the chloride complexes which produced the best results. Therefore, a concentration of 0.3 mol l⁻¹ of HCl was added to the samples and calibration solutions. A linear response was obtained between the detection limit (3σ) of 0.225 and 80 μg l⁻¹. The R.S.D.% (n = 10) for a solution containing 50 μg l⁻¹ of Bi was 0.85%. The tolerance of the system to interferences was evaluated by investigating the effect of the following ions: Cu²⁺, Co²⁺, Ni²⁺, Fe³⁺, Cd²⁺, Pb²⁺, Hg²⁺, Zn²⁺, and Mg²⁺. The most severe depression was caused by Hg²⁺, which at 60 mg l⁻¹ caused a 5% depression on the signal. For the other cations, concentrations between 1000 and 10,000 mg l⁻¹ could be tolerated. The system was applied to the determination of Bi in urine of patients under therapy with bismuth subcitrate. The recovery of spikes of 5 and 50 μg l⁻¹ of Bi added to the samples prior to digestion with HNO₃ and H₂O₂ was in satisfactory ranges from 95.0 to 101.0%. The concentrations of bismuth found in six selected samples using this procedure were in good agreement with those obtained by an alternative technique (ETAAS). Finally, the concentration of Bi determined in urine before and after 3 days of treatment were 1.94 ± 1.26 and 9.02 ± 5.82 μg l⁻¹, respectively.     

Ba—Pb—O和Bi—Pb—O的电化学合成和表征

本文研究了用电化学方法在水溶液中合成铅基氧化物Ｂａ－Ｐｂ－Ｏ和Ｂｉ－Ｐｂ－Ｏ的方法，并采用ＸＰＳ，ＸＲＤ和ＥＤＸ对电合成产物进行了表征。