SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜研究

通过在磺化聚醚醚酮(SPEEK,DS=61.68%)中分别混入酚酞型聚醚砜(PES-C)、磺化酚酞型聚醚砜(SPES-C,DS=53.7%)制备出SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜.结果表明,共混的两种聚合物之间均具有较好的相容性.PES-C、SPES-C的混入能有效降低膜的溶胀及甲醇透过,且随着共混量的增加,这种作用越趋明显.纯SPEEK膜在75℃左右溶解,而SPEEK/PES-C(30wt%)、SPEEK/SPES-C(30wt%)共混膜在80℃时溶胀度仅为22.5%、26.32%.在室温至80℃范围内,纯SPEEK及共混膜的甲醇透过系数都在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,温度大于90℃时,SPEEK/PES-C(20wt%)共混膜电导率超过Nafion115膜;温度大于110℃时,SPEEK/SPES-C(30wt%)共混膜电导率与Nafion115膜相当,达到0.11S.cm-1.高电导率,低透醇系数以及明显提高了的可使用温度表明该类共混膜有望在DMFC中使用.     

SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜研究

通过在磺化聚醚醚酮(SPEEK,DS=61.68%)中分别混入酚酞型聚醚砜(PES-C)、磺化酚酞型聚醚砜(SPES-C,DS=53.7%)制备出SPEEK/PES-C、SPEEK/SPES-C共混质子交换膜.结果表明,共混的两种聚合物之间均具有较好的相容性.PES-C、SPES-C的混入能有效降低膜的溶胀及甲醇透过,且随着共混量的增加,这种作用越趋明显.纯SPEEK膜在75℃左右溶解,而SPEEK/PES-C(30 wt%)、SPEEK/SPES-C(30 wt%)共混膜在80℃时溶胀度仅为22.5%、26.32%.在室温至80℃范围内,纯SPEEK及共混膜的甲醇透过系数都在10-7 cm2·s-1数量级上,远小于Nation[R]115膜.在饱和湿度下,温度大于90℃时,SPEEK/PES-C(20 wt%)共混膜电导率超过Nation[R]115膜;温度大于110℃时,SPEEK/SPES-C(30 wt%)共混膜电导率与Nafion[R]115膜相当,达到0.11 S·cm-1.高电导率,低透醇系数以及明显提高了的可使用温度表明该类共混膜有望在DMFC中使用.     

DMFCs用磺化聚醚醚酮/功能化二氧化硅复合质子交换膜

在磺化度(DS)为55.1%的磺化聚醚醚酮(SPEEK)中掺杂功能化二氧化硅(吸湿性SiO2溶胶及带有磺酸基团的二氧化硅(SiOx-S)粒子)制备SPEEK/SiO2和SPEEK/SiOx-S复合质子交换膜.SiO2和SiOx-S的掺杂能有效提高复合膜的抗溶胀、阻醇性能及高温低湿情况下的电导率.纯SPEEK膜在80℃溶胀为52.6%,而SiO2和SiOx-S掺杂量为15%的复合膜在此温度下分别仅有26.2%和27.3%的溶胀.在室温至80℃范围内,SPEEK/SiO2(20 wt%)和SPEEK/SiOx-S(20 wt%)复合膜的甲醇透过系数比Nafion115膜小近2个数量级.在120℃、相对湿度(RH)为40%情况下,SPEEK纯膜的电导率仅为2.6×10-4S.cm-1,SPEEK/SiO2(20 wt%)复合膜约为2.0×10-3S.cm-1,而SPEEK/SiOx-S(20 wt%)复合膜高达1.0×10-2S.cm-1,与Nafion115相当.SPEEK/SiO2(20 wt%)和SPEEK/SiOx-S(20 wt%)2种复合膜的尺寸稳定性较高,膜电极无催化剂与膜分离现象,其DMFCs单电池性能好于SPEEK膜.     

磺化聚醚醚酮／二氧化硅／磷钨酸复合膜的质子传导率与阻醇性

1引言 由于磺化聚醚醚酮（SPEEK）膜特有的微观结构使其阻醇性能要优于Nafion膜，使其在直接甲醇燃料电池（DMFC）中的应用方面具有良好的应用前景。但随着该材料磺化度的增加，SPEEK膜的抗溶胀性能和机械性能显著下降，而低磺化度的SPEEK的质子传导能力较弱，不能满足DMFC的使用要求。     

DMFC用PES/SPEEK共混阻醇质子交换膜

将磺化聚醚醚酮(SPEEK, 磺化度DS为68.3%)和聚醚砜(PES)两种聚合物共混制得PES/SPEEK共混膜. DSC研究表明两种聚合物之间具有较好的相容性, 因而共混膜均匀致密, 未发生大尺度相分离. PES的混入能有效降低膜的溶胀度及甲醇透过系数. 纯SPEEK 膜40 ℃时在1 mol•L−1甲醇水溶液中溶胀度达到160%, 45 ℃时就完全溶解, 而含30%(w)PES的共混膜在80 ℃时的溶胀度仅有15%. 室温下含20%−30%(w)PES的共混膜的甲醇透过系数为1×10−7 cm2•s−1左右, 比Nafion 115膜的透过系数小一个数量级. 尽管80 ℃下30%(w)PES/SPEEK共混膜的电导率与Nafion 115膜相当, 但由于共混膜的厚度比Nafion 115膜小1/3左右, 膜电阻较小, 因而其电池性能比Nafion 115膜的好.     

磺化聚醚醚酮/三羧基丁烷膦酸锆复合质子交换膜的研究

通过在磺化聚醚醚酮(SPEEK)中掺杂1,2,4-三羧基丁烷-2-膦酸锆(Zr(PBTC))制备出SPEEK/Zr(PBTC)复合质子交换膜.结果表明,与纯SPEEK膜相比,Zr(PBTC)的掺杂能降低复合膜的吸液量及甲醇透过系数,且随着Zr(PBTC)含量的增加,这种作用越趋明显.在室温至80℃范围内,复合膜的甲醇透过系数在10-7cm2.s-1数量级上,远小于Nafion115膜.在饱和湿度下,当温度大于90℃时,含40wt%Zr(PBTC)的复合膜电导率超过Nafion115膜,并在160℃时达到0.36S.cm-1.使用温度的提高及在高温下的高电导率表明该复合膜适合在高温DMFC中使用.     

新型共混交联磺化聚醚醚酮/部分氟化磺化聚芳醚砜质子交换膜的制备与表征

制备了基于磺化聚醚醚酮(SPEEK)/部分氟化磺化聚芳醚砜(SPFAES)的共混交联型质子交换膜(CMB), 研究了其吸水率、 尺寸变化、 力学性能、 热性能、 质子电导率、 化学稳定性及电池性能等. 通过在溶液浇铸过程中加入脱水剂诱导高温脱水反应, 在共混体系内构建了交联结构. 结果表明, 由于SPEEK与SPFAES之间良好的相容性、 分散性和聚合物链的重排及交联作用, CMB膜在干态下均表现出出色的力学强度, 且物化稳定性得到大幅提升. 在低离子交换容量(1.21~1.51 mmol/g)条件下, CMB膜的质子电导率达到122~219 mS/cm(80 ℃), 在氢氧单电池中, CMB4膜的最大功率密度达到530.5 mW/cm²(80 ℃).     

磺化聚醚醚酮与壳聚糖共混制备直接甲醇燃料电池用质子交换膜

给出了不同磺化度下的磺化聚醚醚酮(SPEEK)用作质子交换膜的一系列性能,另外提出了一种新型的酸碱共混质子交换膜,其中,磺化聚醚醚酮和壳聚糖分别被选为酸性、碱性高分子电解质,并对所制备的质子交换膜的相关性能如质子传导性,甲醇渗透性,吸水率以及膜溶胀性、热稳定性等进行了表征,结果表明此种新型复合膜尽管在质子传导性能方面有所下降,阻醇性能改变不大,但是膜溶胀性和吸水率方面有了较大的改善.磺化度为71.4%的SPEEK与壳聚糖以5∶1摩尔比共混制备的质子交换膜,其性质可以与商品化的Nafion 117相媲美,有望在甲醇燃料电池中得到应用.     

全钒液流电池用磺化聚醚醚酮/锂皂石质子膜的结构及性能

通过溶液流延法制备了磺化聚醚醚酮/锂皂石(SPEEK/Lap)复合膜, 对其物理化学性质、 机械性能、 化学稳定性及单电池性能进行了测试. 在SPEEK基质中引入的Lap有效改善了复合膜的质子传导率、 溶胀率和机械性能. 当Lap添加量(质量分数)从0.2%增到1.5%时, 复合膜的质子传导率随之增加(19.9~23.6 mS/cm). SPEEK/Lap-0.2复合膜的自放电时间为57.2 h, 是Nafion 117膜的2.4倍和纯SPEEK膜的1.5倍. 在80 mA/cm ²电流密度下, SPEEK/Lap-0.2复合膜的电压效率(VE, 86.5%)和能量效率(EE, 84.0%)明显高于Nafion 117膜(VE: 83.8%, EE: 80.7%)和纯SPEEK膜(VE: 81.4%, EE: 78.9%). 同时, SPEEK/Lap-0.2复合膜经100次充放电循环测试后具有良好的循环稳定性和结构稳定性.     

杂萘联苯聚芳醚质子交换膜材料的研究

质子交换膜是质子交换膜燃料电池的核心部件之一，其性能的优劣直接关系燃料电池的工作性能。目前质子交换膜燃料电池多采用全氟磺酸离子膜，全氟磺酸膜虽然具有较高的质子传导性和良好的化学稳定性，但是也具有价格昂贵、甲醇渗透高和高温下质子传导性能下降等缺点。为了克服全氟磺酸膜的不足，国内外相继开展了非氟质子交换膜的研究，如磺化聚醚醚酮（SPEEK）、磺化聚醚醚酮酮（SPEEKK）、磺化聚砜（SPSU）和磺化聚酰亚胺（SPI）等。     

利用手持技术改进测定乙醇分子结构实验

利用压强传感器代替排水集气法,改进测定乙醇分子结构实验的仪器装置,并探索最佳反应条件。另外,设计两个空白实验,结合压强变化曲线对实验误差进行相关讨论。     

光谱仪测试范围的扩展

由于石化行业的生产需要，其材质的使用具有多样性和广泛性，经常会出现顾客委托的测试样品的一个或几个元素跨越光谱仪现有测试程序测量范围的情况。本法通过对光谱仪测试原理的认识，根据光谱仪的测试能力及标样的采集，实现了一个或几个元素测量范围的扩展，并对其测量的影响因素进行了研究。     

Dichroism of absorption and polarization of phosphorescence of molecules of the closed form of nitrobenzospirothiopyran

The spectral-polarization characteristics of absorption and phosphorescence of molecules of the initial form of nitro-substituted indolinospirobenzothiopyran were studied in oriented polyethylene films and in solutions with different polarity. An oscillator model of the electron transitions responsible for the formation of absorption and luminescence spectra was suggested. It was established that the principal differences in the spectral and photophysical properties of the compound studied and its oxygen-containing analog are associated with the fact that the electronegativity of the S atom is lower than that of the O atom. Translated fromIzvestiya Akademii Nauk. Seriya Khimicheskaya, No. 6, pp. 1143–1146, June, 1997.     

Influence of viscosity of medium on processes of oxygen quenching of excited states of mesoporphyrin

The oxygen quenching rate constants for singlet and triplet excited states of the dimethyl ester of mesoporphyrin IX increase with decreasing viscosity of the medium and reach a maximum at a viscosity of approximately 0.4 mPa·sec, after which the rate constants begin to decrease. The drop in rate constant with increasing fluidity of the medium may be related to a nonequilibrium character of the elementary act in the interaction of the reactants in the solvent cage. In viscous media such as isopropyl alcohol, isobutyl alcohol, and isoamyl alcohol, the reaction radius is greater than the sum of the radii of the reacting particles. The long-range character of these processes is due to the relatively weak dependence of the quenching probability on distance.Translated from Teoreticheskaya i Éksperimental'naya Khimiya, Vol. 25, No. 2, pp. 161–167, March–April, 1989.     

Determination of heats of detonation and influence of components of composite explosives on heats of detonation of high explosives

The heats of detonation of 20 simple high explosives and explosive mixtures were determined by means of an adiabatic detonation calorimeter designed by the authors. The results indicated that the performance of the instrument was reliable and the experimental data were very accurate. For explosive mixtures, there was a linear accumulative relationship between the heats of detonation of the explosive mixture and its components. Accordingly, the heats of detonation of explosive mixtures could be calculated directly from the heats of detonation of simple explosives and the characteristic heats of other components. The experiments showed that the gold or brass shell of the cylindrical charge could be substituted by a thick-walled porcelain shell, which had the advantage of cheapness.

     

Neutral diterpenoids of oleoresins of five species of conifers of Transcarpathia

The compositions of the neutral diterpenoids of the oleoresins of five species of conifers growing in the Transcarpathia have been studied. It has been found that the oleoresins ofAbies alba M.,Larix decidua M., andPicea excelsa L. contain more than 50% of neutral diterpenoids. The group and qualitative compositions of the oxygen-containing diterpenoids have been determined. In the oleoresins ofAbies alba,Picea excelsa, andPicea abies tertiary alcohols — cis-abienol and isocembrol — predominate, while inLarix decidua the main component is the hydroxy ester larixyl acetate. Primary alcohols related to the resin acids have been found in all the oleoresins investigated. Features of the distribution of diterpenoids according to the species of conifers have been revealed. The results obtained are necessary for the chemotaxonomy of conifers of the family Pinceae.Novosibirsk Institute of Organic Chemistry, Siberian Branch, Academy of Sciences of the USSR. Translated from Khimiya Prirodynkh Soedinenii, No. 6, pp. 812–816, November–December, 1988.     

物质分配系数的测定实验改进

实验教学目的是从解决实际问题出发,以实验技术训练和实验设计思想培养为目标。介绍了将单一的物质分配系数测定实验改进为综合实验,提高了实验效果及实验资源利用率。     

Calculation of enthalpies of hydrogenation of hydrocarbons

Sets of hydrogen molecule equivalents have been developed which permit the calculation of hydrogenation of different types of carbon-carbon bonds from ab initio total energies (3-21G and 6-31G* basis sets, and, to a more limited extent, for MP2/6-31G* data) of reactants and products. The calculated enthalpies of hydrogenation are in good agreement with experiment for unstrained molecules, with average errors on the order of 2 kcal/mol. The 6-31G* equivalents allow the enthalpies for strained molecules to be calculated accurately, but the 3-21G equivalents do not. The equivalents for both basis sets have been tested by calculating the enthalpies of hydrogenation of carbon-carbon bonds in nitrogen- and oxygen-containing organic molecules, free radicals, and classical carbocations. The results are in good agreement with experiment in most cases.     

非那雄胺合成工艺改进

非那雄胺能抑制5α-还原酶的活性,明显降低二氢睾酮水平,是一种治疗良性前列腺增生的有效药品。该合成工艺以甾烯酮酸为原料,将其与氯化亚砜反应,无须分离即与叔丁胺反应得17β-酰胺化合物,再氧化开环,环合,氢化,脱氢合成了非那雄胺。经元素分析、IR、1HNMR、13CNMR、MS分析表征了其结构。该法无须使用昂贵的2,2-二吡啶二硫化物和剧毒药品苯亚硒酸酐,且以乙酸铵代替氨气,降低了对设备的要求和腐蚀,更适用于工业生产。