Effect of swift heavy ion irradiation on photoluminescence properties of ZnO/PMMA nanocomposite films

We report a study on the SHI induced modifications on structural and optical properties of ZnO/PMMA nanocomposite films. The ZnO nanoparticles were synthesized by the chemical route using 2-mercaptoethanol as a capping agent. The structure of ZnO nanoparticles was confirmed by XRD, SEM and TEM. These ZnO nanoparticles were dispersed in the PMMA matrix to form ZnO/PMMA nanocomposite films by the solution cast method. These ZnO/PMMA nanocomposite films were then irradiated by swift heavy ion irradiation (Ni⁸⁺ ion beam, 100 MeV) at a fluence of 1×10¹¹ ions/cm². The nanocomposite films were then characterized by XRD, UV-vis absorption spectroscopy and photoluminescence spectroscopy. As revealed from the absorption spectra, absorption edge is not changed by the irradiation but the optical absorption is increased. Enhanced green luminescence at about 527 nm and a less intense blue emission peak around 460 nm were observed after irradiation with respect to the pristine ZnO/PMMA nanocomposite film.     

Nano-star formation in Al-doped ZnO thin film deposited by dip-dry method and its characterization using atomic force microscopy, electron probe microscopy, photoluminescence and laser Raman spectroscopy

Zinc oxide doped with Al (AZO) thin films were prepared on borosilicate glass substrates by dip and dry technique using sodium zincate bath. Effects of doping on the structural and optical properties of ZnO film were investigated by XRD, EPMA, AFM, optical transmittance, PL and Raman spectroscopy. The band gap for ZnO:Al (5.0 at. wt.%) film was found to be 3.29 eV compared with 3.25 eV band gap for pure ZnO film. Doping with Al introduces aggregation of crystallites to form micro-size clusters affecting the smoothness of the film surface. Al³⁺ ion was found to promote chemisorption of oxygen into the film, which in turn affects the roughness of the sample. Six photoluminescence bands were observed at 390, 419, 449, 480, 525 and 574 nm in the emission spectra. Excitation spectra of ZnO film showed bands at 200, 217, 232 and 328 nm, whereas bands at 200, 235, 257 and 267 nm were observed for ZnO:Al film. On the basis of transitions from conduction band or deep donors (CB, Zn_i or V_OZn_i) to valence band and/or deep acceptor states (VB, V_Zn or O_i or O_Zn), a tentative model has been proposed to explain the PL spectra. Doping with Al³⁺ ions reduced the polar character of the film. This has been confirmed from laser Raman studies.     

Highly conductive and transparent laser ablated nanostructured Al: ZnO thin films

Al doped ZnO thin films are prepared by pulsed laser deposition on quartz substrate at substrate temperature 873 K under a background oxygen pressure of 0.02 mbar. The films are systematically analyzed using X-ray diffraction, atomic force microscopy, micro-Raman spectroscopy, UV-vis spectroscopy, photoluminescence spectroscopy, z-scan and temperature-dependent electrical resistivity measurements in the temperature range 70-300 K. XRD patterns show that all the films are well crystallized with hexagonal wurtzite structure with preferred orientation along (0 0 2) plane. Particle size calculations based on XRD analysis show that all the films are nanocrystalline in nature with the size of the quantum dots ranging from 8 to 17 nm. The presence of high frequency E₂ mode and longitudinal optical A₁ (LO) modes in the Raman spectra suggest a hexagonal wurtzite structure for the films. AFM analysis reveals the agglomerated growth mode in the doped films and it reduces the nucleation barrier of ZnO by Al doping. The 1% Al doped ZnO film presents high transmittance of ∼75% in the visible and near infrared region and low dc electrical resistivity of 5.94 × 10⁻⁶ Ω m. PL spectra show emissions corresponding to the near band edge (NBE) ultra violet emission and deep level emission in the visible region. Nonlinear optical measurements using the z-scan technique shows optical limiting behavior for the 5% Al doped ZnO film.     

Effects of rf power on surface-morphological, structural and electrical properties of aluminium-doped zinc oxide films by magnetron sputtering

Aluminium-doped zinc oxide (ZnO:Al) films were prepared by magnetron sputtering at different radio-frequency powers (P_rf) of 50, 100, 150 and 200 W. The properties of the films were characterised by X-ray photoelectron spectroscopy (XPS), atomic force microscopy (AFM), Raman microscopy, and spectrophotometry with the emphasis on the evolution of compositional, surface-morphological, optical, electrical and microstructural properties. XPS spectra showed that within the detection limit the films are chemically identical to near-stoichiometric ZnO. AFM revealed that root-mean-square roughness of the films has almost linear increase with increasing P_rf. Optical band gap E_gopt of the films increases from 3.31 to 3.51 eV when P_rf increases from 50 to 200 W. A widening E_gopt of the ZnO:Al films compared to the band gap (∼3.29 eV) of undoped ZnO films is attributed to a net result of the competition between the Burstein-Moss effect and many-body effects. An electron concentration in the films was calculated in the range of 3.73 × 10¹⁹ to 2.12 × 10²⁰ cm⁻³. Raman spectroscopy analysis indicated that well-identified peaks appear at around 439 cm⁻¹ for all samples, corresponding to the band characteristics of the wurtzite phase. Raman peaks in the range 573-579 cm⁻¹ are also observed, corresponding to the A₁ (LO) mode of ZnO.     

Nonlinear optical properties of Au/ZnO nanoparticle arrays

The triangular-shaped Au/ZnO nanoparticle arrays were fabricated on fused quartz substrate using nanosphere lithography. The structural characterization of the Au/ZnO nanoparticle arrays was investigated by atomic force microscopy. The absorption peak due to the surface plasmon resonance of Au particles at the wavelength of about 570 nm was observed. The nonlinear optical properties of the nanoparticle arrays were measured using the z-scan method at a wavelength of 532 nm with pulse duration of 10 ns. The real and imaginary part of third-order nonlinear optical susceptibility, Re χ⁽³⁾ and Im χ⁽³⁾, were determined to be 1.15 × 10⁻⁶ and −5.36 × 10⁻⁷ esu, respectively. The results show that the Au/ZnO nanoparticle arrays have great potential for future optical devices.     

Characterization, sintering and dielectric properties of nanocrystalline zinc oxide prepared by a citric acid-based combustion route

Nanosized zinc oxide has been synthesized through a novel single step solution combustion route using citric acid as fuel. The X-ray diffraction (XRD) analysis revealed that the synthesized ZnO nanopowder has the pure wurtzite structure. The phase purity of the nanopowder has been confirmed using differential thermal analysis (DTA), thermogravimetric analysis (TGA) and Fourier transform infrared spectroscopy (FT-IR). The morphology and crystalline size of the as-prepared nanopowder characterized by scanning electron microscopy (SEM) and transmission electron microscopy (TEM) revealed that the powder consisted of a mixture of nanoparticles and nanorods. The nanocrystalline ZnO could be sintered to ∼97% of the theoretical density at 1200 °C in 4 h. The dielectric constant (ε_r) and dielectric loss (ε_i) of sintered ZnO pellets at 5 MHz were 1.38 and 9×10⁻², respectively, at room temperature.     

Synthesis and investigation of nonlinear optical properties of semiconductor ZnS nanoparticles

ZnS nanoparticles were prepared by a simple chemical method and using PVP (poly vinylpyrrolidone) as capping agent. The sample was characterized by UV-vis spectrophotometer, X-ray diffraction (XRD) and Z-scan technique. XRD pattern showed that the ZnS nanoparticles had zinc blende structure with an average size of about 2.18 nm. The value of band gap of these nanoparticles was measured to be 4.20 eV. The nonlinear optical properties of ZnS nanoparticles in aqueous solution were studied by Z-scan technique using CW He-Ne laser at 632.8 nm. The nonlinear absorption coefficient (β) was estimated to be as high as 3.2×10⁻³ cm/W and the nonlinear refractive index (n₂) was in order of 10⁻⁸ cm²/W. The sign of the nonlinear refractive index obtained negative that indicated this material exhibits self-defocusing optical nonlinearity.     

Swift heavy ion induced modifications in cobalt doped ZnO thin films: Structural and optical studies

Modifications in the structural and optical properties of 100 MeV Ni⁷⁺ ions irradiated cobalt doped ZnO thin films (Zn_1−xCo_xO, x = 0.05) prepared by sol-gel route were studied. The films irradiated with a fluence of 1 × 10¹³ ions/cm² were single phase and show improved crystalline structure with preferred C-axis orientation as revealed from XRD analysis. Effects of irradiation on bond structure of thin films were studied by FTIR spectroscopy. The spectrum shows no change in bonding structure of Zn-O after irradiation. Improved quality of films is further supported by FTIR studies. Optical properties of the pristine and irradiated samples have been determined by using UV-vis spectroscopic technique. Optical absorption spectra show an appreciable red shift in the band gap of irradiated Zn_1−xCo_xO thin film due to sp-d interaction between Co²⁺ ions and ZnO band electrons. Transmission spectra show absorption band edges at 1.8 eV, 2.05 eV and 2.18 eV corresponding to d-d transition of Co²⁺ ions in tetrahedral field of ZnO. The AFM study shows a slight increase in grain size and surface roughness of the thin films after irradiation.     

Structural, optical and electrical properties of Al-N codoped ZnO films by RF-assisted MOCVD method

N-doped ZnO films were produced using N₂ as N source by metal-organic chemical vapor deposition (MOCVD) system which has been improved with radio-frequency (RF)-assisted equipments. The data of secondary ion mass spectroscopy (SIMS) indicate that the concentration of N in N-doped ZnO films is around 5 × 10²⁰ cm⁻³, implying that sufficient incorporation of N into ZnO can be obtained by RF-assisted equipment. On this basis, the structural, optical and electrical properties of Al-N codoped ZnO films were studied. Then, the effect of RF power on crystal quality, surface morphologies, optical properties was analyzed using X-ray diffraction, atomic force microscopy and photo-luminescence methods. The results illustrate that the RF plasma is the key factor for the improvement of crystal quality. Then the observation of A⁰X recombination associated with N_O acceptor in low-temperature PL spectrum proved that some N atoms have occupied the positions of O atoms in ZnO films. Hall measurements shown that p-type ZnO film deposited on quartz glasses was obtained when RF power was 150 W for the Al-N codoped ZnO films, while the resistivity of N-doped ZnO films was rather high. Compared with the Al-doped ZnO film, the obviously increased resistivity of codoped films indicates that the formation of N_O acceptors compensate some donors in ZnO films effectively.     

Preparation and the optical nonlinearity of surface chemistry improved titania nanoparticles in poly(methyl methacrylate)-titania hybrid thin films

With 800-nm, 120-fs laser pulses, optical nonlinearity has been studied in a series of thin films containing poly(methyl methacrylate) (PMMA), filled with surfactant acetylacetone (Acac) capped TiO₂ nanoparticles, which were synthesized by a simple in situ sol-gel/polymerization process, assisted by spin coating and multi-step baking. The resulting nanohybrid thin films have highly optical transparency and demonstrate a unique nonlinear optical (NLO) response. The highest nonlinear refractive index (n₂) is observed up to 6.55 × 10⁻² cm² GW⁻¹ in the nanohybrid thin film of 60 wt% Ti(OBu)₄ in PMMA, with a negligible two-photon absorption (TPA), as confirmed by the Z-scan technique. The titanium precursor loading combined with the nature of the capping molecules are used to influence the ability of nanoparticles to nonlinear optical response. Indeed, the ligands at the nanoparticles’ surface can not only control the extent of the interaction between the organic molecules and the embedded nanoparticles but also influence the optical nonlinearities of nanoparticles.     

Electrical and optical properties of ZnO films prepared by sputtering of ZnO targets containing AlN

ZnO films prepared from the ZnO target containing 2% AlN are transparent irrespective of radio frequency (RF) power. The obtained ZnO films have the carrier density of 3.8 × 10²⁰ cm⁻³ or less and the low mobility of 5.3-7.8 cm²/(V s). In the case of 5% AlN target, ZnO films prepared at 40, 60 and 80 W are transparent, whereas ZnO films prepared at 100 and 120 W are colored. As RF power increases from 40 to 120 W, the carrier density increases straightforwardly up to 5.5 × 10²⁰ cm⁻³ at 100 W and is oppositely reduced to 3.2 × 10²⁰ cm⁻³ at 120 W. In the case of 10% AlN target, ZnO films prepared at 60 W or more are colored, and have the carrier density of 4 × 10²⁰ cm⁻³ or less. The N-concentration in these colored films is estimated to be 1% or less. The Al-concentration in the ZnO films prepared from the 5 and 10% AlN targets is higher than 2%. The carrier density of the ZnO films containing Al and N atoms is nearly equal to that of ZnO films doped with Al atoms alone. There is no evidence in supporting the enhancement of the carrier density via the formation of N-Al_xZn_4−x clusters (4 ≥ x ≥ 2).     

Influence of sputter-etching of substrate on the microstructural and optical properties of ZnO films deposited by RF magnetron sputtering

ZnO films were prepared using radio frequency magnetron sputtering on Si(1 1 1) substrates that were sputter-etched for different times ranging from 10 to 30 min. As the sputter-etching time of the substrate increases, both the size of ZnO grains and the root-mean-square (RMS) roughness decrease while the thickness of the ZnO films shows no obvious change. Meanwhile, the crystallinity and c-axis orientation are improved by increasing the sputter-etching time of the substrate. The major peaks at 99 and 438 cm⁻¹ are observed in Raman spectra of all prepared films and are identified as E₂(low) and E₂(high) modes, respectively. The Raman peak at 583 cm⁻¹ appears only in the films whose substrates were sputter-etched for 20 min and is assigned to E₁(LO) mode. Typical ZnO infrared vibration peak located at 410 cm⁻¹ is found in all FTIR spectra and is attributed to E₁(TO) phonon mode. The shoulder at about 382 cm⁻¹ appearing in the films whose substrates were sputter-etched for shorter time (10-20 min) originates from A₁(TO) phonon mode. The results of photoluminescence (PL) spectra reveal that the optical band gap (Eg) of the ZnO films increases from 3.10 eV to 3.23 eV with the increase of the sputter-etching time of the substrate.     

Microstructural and optical properties of europium-doped zinc oxide nanowires

Single-crystal Eu³⁺-doped wurtzite ZnO micro- and nanowires were synthesized by chemical vapor deposition. The nanostructures grew via a self-catalytic mechanism on the walls of an alumina boat. The structure and properties of the doped ZnO were characterized using X-ray diffraction, energy-dispersive X-ray spectroscopy, scanning and transmission electron microscopy, and photoluminescence (PL) methods. A 10-min synthesis yielded vertically grown nanowires of 50–400 nm in diameter and several micrometers long. The nanowires grew along the ±[0001] direction. The Eu³⁺ concentration in the nanowires was 0.8 at.%. The crystal structure and microstructure of were compared for Eu³⁺-doped and undoped ZnO. PL spectra showed a red shift in emission for Eu³⁺-doped (2.02 eV) compared to undoped ZnO nanowires (2.37 eV) due to Eu³⁺ intraionic transitions. Diffuse reflectance spectra revealed widening of the optical bandgap by 0.12 eV for Eu³⁺-doped compared to undoped ZnO to yield a value of 3.31 eV. Fourier-transform infrared spectra confirmed the presence of europium in the ZnO nanowires.     

ZnO nanoparticles produced by novel reactive physical deposition process

This paper reports the deposition of ZnO nanoparticles with controlled sizes and different particle densities and their structural, composition and optical properties. They were deposited by means of a DC magnetron based vacuum nanoparticle source onto different substrates (GaAs, Si and Ti/SiO₂/Si). We believe that this is the first time that such nanoparticles have been produced using this unique technique. Zinc was used as sputtering target to produce zinc nanoparticles which were oxidized in-line using molecular oxygen. The structural properties and chemistry of the ZnO were studied by transmission electron microscopy. An average particle size of 6(±2) nm was produced with uniform size distribution. The particle density was controlled using a quartz crystal monitor. Surface densities of 2.3 × 10¹¹/cm², 1.1 × 10¹³/cm² and 3.9 × 10¹³/cm² were measured for three different deposition runs. The ZnO particles were found to be single crystalline having hexagonal structure. Photoluminescence measurements of all samples were performed at room temperature using a cw He-Cd laser at 325 nm excitation. The UV emission around 375 nm at room temperature is due to excitonic recombination and the broad emission centered at 520 nm may be attributed to intrinsic point defects such as oxygen interstitials.     

Influence of Fe-doping on the structural,optical and magnetic properties of ZnO nanoparticles

Zn_1–xFe_xO (x=0–0.05) nanoparticles were synthesized without a catalyst by a two-step method. Fe was doped into ZnO by a source of metallic Fe sheets in a solid–liquid system at 80 °C, and the Zn_1−xFe_xO nanoparticles were obtained by annealing at 300 °C. X-ray diffraction, X-ray photoelectron spectroscopy (XPS) and transmission electron microscopy were used to characterize the structural properties of the as-grown Zn_1−xFe_xO. The optical properties were determined by Infrared and Ultraviolet–visible spectroscopy. The results confirm that the crystallinity of the ZnO is deteriorated due to Fe-doping. XPS results show that there is a mixture of Fe⁰⁺ and the Fe³⁺ in the representative Zn_0.95Fe_0.05O sample. The optical band gap of Zn_1−xFe_xO is enhanced with increasing of Fe-doping. Room temperature ferromagnetism was observed in all the Fe-doped ZnO samples.     

Optical properties of samarium doped zinc-phosphate glasses

Samarium doped zinc-phosphate glasses having composition Sm₂O_{3 (x)}ZnO_(60−x) P₂O_{5 (40)} (where x=0.1-0.5 mol%) were prepared by melt quenching method. The density of these glasses was measured by Archimedes method; the corresponding molar volumes have also been calculated. The values of density range from 3.34 to 3.87 gm/cm³ and those of molar volume range from 27.62 to 31.80 cm⁻³. The optical absorbance studies were carried out on these glasses to measure their energy band gaps. The absorption spectra of these glasses were recorded in UV-visible region. No sharp edges were found in the optical spectra, which verifies the amorphous nature of these glasses. The optical band gap energies for these glasses were found to be in the range of 2.89-4.20 eV. The refractive index and polarizability of oxide ion have been calculated by using Lorentz-Lorentz relations. The values of refractive index range from 2.13 to 2.42 and those of polarizability of oxide ion range from 6.51×10⁻²⁴ to 7.80×10⁻²⁴ cm³.     

Femtosecond Z-scan measurement of third-order optical nonlinearities in anatase TiO2 thin films

Anatase phase TiO₂ films have been grown on fused silica substrate by pulsed laser deposition technique at substrate temperature of 750 °C under the oxygen pressure of 5 Pa. From the transmission spectra, the optical band gap and linear refractive index of the TiO₂ films were determined. The third-order optical nonlinearities of the films were measured by Z-scan method using a femtosecond laser (50 fs) at the wavelength of 800 nm. The real and imaginary parts of third-order nonlinear susceptibility χ⁽³⁾ were determined to be −7.1 × 10⁻¹¹esu and −4.42 × 10⁻¹²esu, respectively. The figure of merit, T, defined by T=βλ/n₂, was calculated to be 0.8, which meets the requirement of all-optical switching devices. The results show that the anatase TiO₂ films have great potential applications for nonlinear optical devices.     

Fabrication of waveguides in Yb:YCOB crystal by MeV oxygen ion implantation

Oxygen ions with energies of 6.0 or 3.0 MeV were implanted into y-cut Yb:YCOB crystals at fluences ranging from 5.0 × 10¹³ to 2.0 × 10¹⁵ ions/cm² at room temperature, forming optical planar waveguide structures. Dark-mode line spectroscopy was applied at two wavelengths, 633 and 1539 nm, in various excitation configurations, showing strong enhancement of one of the indices (n_x) in the implanted near surface. The n_x refractive index profile is reconstructed by a reflectivity calculation method and compared to the ion energy losses profiles deduced from SRIM-code simulation. Moreover, the near-field patterns were imaged by an end-fire coupling arrangement.     

Nonlinear optical properties in SrTiO3 thin films by pulsed laser deposition

Well-crystallized 250 nm-thick SrTiO₃ thin films on fused-quartz substrate were prepared by pulsed laser deposition. The band-gap of SrTiO₃ thin film by transmittance spectra is equal to 3.50 eV, larger than 3.22 eV for the bulk crystal. The nonlinear optical properties of the films were examined with picosecond pulses at 1.064 μm excitation. A large two-photon absorption (TPA) with absorption coefficient of 87.7 cm/GW was obtained, larger than 51.7 cm/GW for BaTiO₃ thin films. The nonlinear refractive index n₂ is equal to 5.7×10⁻¹⁰ esu with a negative sign, larger than 0.267×10⁻¹¹ esu for bulk SrTiO₃. The large TPA is attributed to intermediate energy levels introduced by the grain boundaries, and the optical limiting behaviors stemming from both TPA and negative nonlinear refraction were also discussed.     

Effects of seed layer on the structure and property of zinc oxide thin films electrochemically deposited on ITO-coated glass

ZnO films with different morphologies were deposited on the ITO-coated glass substrate from zinc nitrate aqueous solution at 65 °C by a seed-layer assisted electrochemical deposition route. The seed layers were pre-deposited galvanostatically at different current densities (i_sl) ranging from −1.30 to −3.0 mA/cm², and the subsequent ZnO films had been done using the potentiostatic technique at the cathode potential of −1.0 V. Densities of nucleation centers in the seed layers varied with increasing the current density, and the ZnO films on them showed variable morphologies and optical properties. The uniform and compact nanocrystalline ZnO film with (0 0 2) preferential orientation was obtained on seed layer that was deposited under the current density (i_sl) of −1.68 mA/cm², which exhibited good optical performances.