Phase transition, structural and electrical properties of Pb(Zn1/3Nb2/3)O3-doped Pb(Ni1/3Nb2/3)O3-PbTiO3 ceramics prepared by solid-state reaction method

Phase pure perovskite (1−x−y)Pb(Ni_1/3Nb_2/3)O₃-xPb(Zn_1/3Nb_2/3)O₃-yPbTiO₃ (PNN-PZN-PT) ferroelectric ceramics were prepared by conventional solid-state reaction method via a B-site oxide mixing route. The PNN-PZN-PT ceramics sintered at the optimized condition of 1185 °C for 2 h exhibit high relative density and rather homogenous microstructure. With the increase of PbTiO₃ (PT) content, crystal structure and electrical properties of the synthesized PNN-PZN-PT ceramics exhibit successive phase transformation. A morphotropic phase boundary (MPB) is supposed to form in (0.9−x)PNN-0.1PZN-xPT at a region of x=32-36 mol% confirmed by X-ray diffraction (XRD) measurement and dielectric measurement. The MPB composition can be pictured as providing a “bridge” connecting rhombohedral ferroelectric (FE) phase and tetragonal one since crystal structure of the MPB composition is similar to both the rhombohedral and tetragonal lattices. Dielectric response of the sintered PNN-PZN-PT ceramics also exhibits successive phase-transition character. 0.64PNN-0.1PZN-0.26PT exhibits broad, diffused and frequency dependent dielectric peaks indicating a character of diffused FE-paraelectric (PE) phase transition of relaxor ferroelectrics and 0.40PNN-0.1PZN-0.50PT exhibits narrow, sharp and frequency independent dielectric peaks indicating a character of first-order FE-PE phase transition of normal ferroelectrics. The FE-PE phase transition of 0.56PNN-0.1PZN-0.34PT is nearly first-order with some diffused character, which also exhibits the largest value of piezoelectric constant d₃₃ of 462pC/N.     

Dependence of high electric-field-induced strain on the composition and orientation of Pb(Mg1/3Nb2/3)O3-PbTiO3 crystals

Electric-field-induced strain behavior of (1−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃ (PMNT) crystals with different orientations and compositions was investigated for use as electromechanical actuators. Crystallographically, high strains with low hysteresis were achieved for 〈001〉 oriented rhombohedral crystals (29%≤x≤31%) near a morphotropic phase boundary, rather than 〈110〉 and 〈111〉. Domain instability could explain inferior strain levels and large hysteresis for 〈110〉 and 〈111〉 oriented crystals. Ultrahigh strain levels up to 1.8% could be achieved for 〈001〉 oriented PMNT crystals, being related to an E-field induced phase transition. −2 kV/cm negative E-field can be applied to PMNT ferroelectric material with low hysteresis. High strain with low hysteresis makes PMNT crystals promising candidates for high performance solid-state actuators.     

Phase transformation in (0.90−x)Pb(Mg1/3Nb2/3)O3-xPbTiO3-0.10PbZrO3 piezoelectric ceramic: X-ray diffraction and Raman investigation

Piezoelectric ceramics with compositions of (0.90−x)Pb(Mg_1/3Nb_2/3)O₃-xPbTiO₃-0.10PbZrO₃, x=0.28, 0.31, 0.34, 0.37, 0.40 and 0.43, were prepared using the conventional columbite precursor method, and their structural phase transformation and piezoelectric behaviors near the morphotropic phase boundary (MPB) have been systematically investigated as a function of PbTiO₃ content. X-ray diffraction (XRD) results demonstrate that the structure of the ceramics experiences a gradual transition process from rhombohedral phase to tetragonal phase with the increasing of PbTiO₃ content, and that compositions with x=0.34-0.40 lie in the MPB region of this ternary system. A Raman spectra investigation of the ceramic samples testified to the transformation process of rhombohedral phase to tetragonal phase by comparing the relative intensities of tetragonal E(2TO₁) mode and rhombohedral phase R_h mode. The structure information was also correlated to the parabola change of the piezoelectric constant; the maximum piezoelectric constants were obtained near the MPB region.     

Dielectric properties and phase transitions of (Pb0.87La0.02Ba0.1)(Zr0.6Sn0.4−xTix)O3 ceramics with compositions near AFE/RFE phase boundary

The electrical properties and phase transition behavior of (Pb_0.87La_0.02Ba_0.1)(Zr_0.6Sn_0.4−xTi_x)O₃ solid solutions (PLBZST, 0.04≤x0.2) were investigated by the X-ray diffraction, permittivity, pyroelectric current, and P-E electric hysterisis loops. As the composition x increased from 0.04 to 0.2, the antiferroelectric ceramics (x≤0.07, AFE) with tetragonal phase changed to the ferroelectric relaxors (RFE, 0.09≤x). AFE ceramics showed a peculiar diffuse phase transition and dielectric relaxation at the low temperature (down to −100 °C) due to a frustration between AFE and FE state. With an increase in composition x, electrically field-induced AFE-FE switching field (E_AFE-FE) and AFE-paraelectric (PE) phase transition temperature (T_c) are depressed in the temperature (T)-Ti composition (x) phase diagram, a FE-AFE-PE triple phase point (T_tr) with the lowest transition temperature occurred at x=0.09. The pyroelectric currents under an application of various external electric field (E) were measured to identify a T-E phase diagram of the PLBZST compound.     

Field and temperature induced colossal strain in Gd5(SixGe1−x)4

Gd₅(Si_xGe_1−x)₄, known for its giant magnetocaloric effect, also exhibits a colossal strain of the order of 10,000 ppm for a single crystal near its coupled first-order magnetic-structural phase transition, which occurs near room temperature for the compositions 0.41≤x≤0.575. Such colossal strain can be utilised for both magnetic sensor and actuator applications. In this study, various measurements have been carried out on strain as a function of magnetic field strength and as a function of temperature on single crystal Gd₅Si₂Ge₂ (x=0.5), and polycrystalline Gd₅Si_1.95Ge_2.05 (x=0.487) and Gd₅Si_2.09Ge_1.91 (x=0.52). Additionally a giant magnetostriction/thermally induced strain of the order of 1800 ppm in polycrystalline Gd₅Si_2.09Ge_1.91 was observed at its first order phase transition on varying temperature using a Peltier cell without the use of bulky equipment such as cryostat or superconducting magnet.     

Thermal expansion in the Burns-phase of barium titanate stannate

The thermal expansion S_T has been measured in the system BaTi_1−xSn_xO₃, both for the pure compositions x=0 (BT) and x=1 (BS), and for solid solutions 0.025≤x≤0.2 (BTS). For all ceramics examined, a non-linear temperature dependence S_T(T) has been observed at elevated temperatures This is related to thermally generated impurities and, below the Burns-temperature T_d of BT and BTS, to the non-linear strain contribution of polar nanoregions. With increasing Sn-content x, a steep increase of the Burns-temperature is found in BTS for compositions x≥0.025.     

Structure and magnetostriction of Tb0.2Pr0.8(Fe0.4Co0.6)1.93−xCx intermetallic compounds

The structure and magnetostriction of Tb_0.2Pr_0.8(Fe_0.4Co_0.6)_1.93−xC_x intermetallic compounds were studied by X-ray diffraction and magnetic measurements. Almost a single cubic Laves phase forms in the alloys for x ≤0.20, and a small amount of C can inhibit the formation of the 1:3 phase. The lattice parameter increases when 0≤x≤0.15, while the T_c and the spontaneous magnetization decreases with increasing x. The lattice parameter decreases slowly when 0.15≤x≤0.30, while the T_c decreases evidently with increasing x. The magnetostriction λ_a (=λ_∥-λ_⊥) is improved at low magnetic fields at room temperature for the compounds with 0.05≤x≤0.10, indicating that these C-containing compounds are promising magnetostrictive materials.     

Effect of sintering temperature on the structural, dielectric and ferroelectric properties of tungsten substituted SBT ceramics

Structural, dielectric and ferroelectric properties of tungsten (W) substituted SrBi₂(Ta_1−xW_x)₂O₉ (SBTW) [x=0.0, 0.025, 0.05, 0.075, 0.1 and 0.2] have been studied as a function of sintering temperature (1100-1250 °C). X-ray diffraction patterns confirm the single-phase layered perovskite structure formation up to x=0.05 at all sintering temperatures. The present study reveals an optimum sintering temperature of 1200 °C for the best properties of SBTW samples. Maximum T_c of ∼390 °C is observed for x=0.20 sample sintered at 1200 °C. Peak-dielectric constant (ε_r) increases from ∼270 to ∼700 on increasing x from 0.0 to 0.20 at 1200 °C sintering temperature. DC conductivity of the SBTW samples is nearly two to three orders lower than that of the pristine sample. Remnant polarization (P_r) increases with the W content up to x≤0.075. A maximum 2P_r (∼25 μC/cm²) is obtained with x=0.075 sample sintered at 1200 °C. The observed behavior is explained in terms of improved microstructural features, contribution from the oxygen and cationic vacancies in SBTW. Such tungsten substituted samples sintered at 1200 °C exhibiting enhanced dielectric and ferroelectric properties should be useful for memory applications.     

A survey on the effect of vanadium content on the magnetoelastic properties of YFe12−xVx alloys

Experimental results on the thermal expansion and magnetostriction of YFe_12−xV_x (1.5≤x≤3.5) alloys are reported. The results show that the anisotropic magnetostriction (Δλ) at a finite field (1.5 T) increases with increasing vanadium content in the range of x<2. But for x>2, a decrease in the magnetic anisotropy with increasing vanadium content causes a decrease in the saturation values of Δλ. In addition, the thermal expansion coefficient becomes a minimum for x≈2. Experimental curves exhibit that the forced volume magnetostriction (ΔV/V) is positive and increases linearly with the applied field at high fields. But in the low field region (≤0.5 T), a minimum appears in the isothermal curves of ΔV/V around the saturation field. The results are explained by considering the influence of vanadium content on the magnetization anisotropy of YFe_12−xV_x compounds.     

Influence of Ce doping on electrical and thermal properties of La0.7−xCexCa0.3MnO3 (0.0≤x≤0.7) manganites

The effect of Ce-doping on structural, magnetic, electrical and thermal transport properties in hole-doped manganites La_0.7−xCe_xCa_0.3MnO₃ (0.0≤x≤0.7) is investigated. The structure of the compounds was found to be crystallized into orthorhombically distorted perovskite structure. dc Susceptibility versus temperature curves reveal various magnetic transitions. For x≤0.3, ferromagnetic regions (FM) were identified and the magnetic transition temperature (T_C) was found to be decreasing systematically with increasing Ce concentration. The electrical resistivity ρ(T) separates the well-define metal-semiconducting transition (T_MS) for low Ce doping concentrations (0.0≤x≤0.3) consistent with magnetic transitions. For the samples with 0.4≤x≤0.7, ρ(T) curves display a semiconducting behavior in both the high temperature paramagnetic (PM) phase and low temperature FM or antiferromagnetic phase. The electron–phonon and electron–electron scattering processes govern the low temperature metallic behavior, whereas small polaron hopping model is found to be operative in PM phases for all samples. These results were broadly corroborated by thermal transport measurements for metallic samples (x≤0.3) in entire temperature range we investigated. The complicated temperature dependence of Seebeck coefficient (S) is an indication of electron–magnon scattering in the low temperature magnetically ordered regime. Specific heat measurements depict a broadened hump in the vicinity of T_C, indicating the existence of magnetic ordering and magnetic inhomogeneity in the samples. The observation of a significant difference between ρ(T) and S(T) activation energies and a positive slope in thermal conductivity κ(T) implying that the conduction of charge carriers were dominated by small polaron in PM state of these manganites.     

Raman scattering in TlInS2xSe2(1−x) layered mixed crystals (0.25≤x≤1): Compositional dependence of the mode frequencies and line widths

The Raman spectra of TlInS_2xSe_2(1−x) layered mixed crystals were studied for a wide composition range (0.25≤x≤1) in the frequency region 10-360 cm⁻¹ at room temperature. The shift of Raman-active phonon frequencies versus mixed crystals composition x were established. The effect of crystal disorder on the line width broadening of three high-frequency Raman-active modes is reported.     

Structural, magnetic properties and magnetostriction studies of Sm1−xNdxFe1.55 alloys

Structural, magnetic properties and magnetostriction studies of Sm_1−xNd_xFe_1.55 (0≤x≤0.56) alloys have been performed. X-ray diffraction analysis confirms the presence of single cubic Laves phase in Sm_1-xNd_xFe_1.55 alloys with 0≤x≤0.48. The lattice parameter of alloys increases linearly with increase in Nd content while the Curie temperature behaves in the opposite way. The alloy x=0.08 exhibits a giant magnetostriction value (λ_∥-λ_⊥) of −2187 ppm at a magnetic field of 12 kOe due to the anisotropy compensation between Sm³⁺ and Nd³⁺ ions.     

Investigation of the solid solution series 2(MnX)-CuInX2 (X=S, Se)

(2MnX)_x(CuInX₂)_1−x with X=S and Se were prepared by solid state reaction from the end members α-MnS, β-MnS and CuInS₂ in the range 0<x≤0.2 (≤0.6 for β-MnS) as well as MnSe and CuInSe₂ in the range 0<x≤0.1. Mixed crystals with 0≤x≤0.1 crystallize in the tetragonal chalcopyrite type structure, (2α-MnS)_x(CuInS₂)_1−x samples with 0.1<x≤0.2 and (2β-MnS)_x(CuInS₂)_1−x samples up to x=0.6 consist of two phases, occuring as tetragonal domains (x∼0.1 for X=S) within a cubic matrix with zinc-blende type structure (x∼0.4 for X=S), indicating a miscibility gap. For tetragonal single phase samples the band gap energy, the lattice constants and the anion parameter have been determined. The first and the latter ones show a different composition dependent behaviour caused by the modification of the MnS (α-MnS with NaCl type structure, β-MnS with zinc-blende type structure) used during the synthesis. Additionally a CuMn_xIn_1−xS₂ powder sample, in which Mn substitutes the M^III site, was investigated. The SQUID measurements revealed a well-distinct magnetic transition between 15 and 16 K as well as ferromagnetic-like hysteresis loops pronounced for temperatures below the transition temperature. Below this temperature a clear splitting between the zero field cooling (ZFC) and the field cooling (FC) curves indicate to the existence of a long-range magnetic ordering phenomenon. This behaviour was not found in the other samples were Mn substitutes both sites M^I as well as M^III.     

Photoluminescence properties of Eu in Y(PO3)3 under VUV excitation

The photoluminescence properties of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) are investigated. The excitation spectrum of Y_0.85(PO₃)₃:0.15Eu₃⁺ shows that both the (PO₃)₃³⁻ groups and the CT bands of O²⁻-Y³⁺ can efficiently absorb the excitation energy in the region of 120-250 nm. Under 147 nm excitation, the optimal emissive intensity of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) is about 36% of the commercial phosphor (Y,Gd)BO₃:Eu³⁺, which hints that the absorbed energy by the host matrix could be efficiently transferred to Eu³⁺. We try to study the concentration quenching mechanism of Y_1−x(PO₃)₃:xEu³⁺ (0<x≤0.2) under 147 and 172 nm excitation.     

Carbon doping in MgB2: role of boron and carbon px(y) bands

We have studied the changes in the electronic structure and the superconducting transition temperature T_c of Mg(B_1−xC_x)₂ alloys as a function of x with 0≤x≤0.3. Our density-functional-based approach uses the coherent-potential approximation to describe the effects of disorder, the Gaspari-Gyorffy formalism to estimate the electron-phonon matrix elements and the Allen-Dynes equation to calculate T_c in these alloys. We find that the changes in the electronic structure of Mg(B_1−xC_x)₂ alloys, especially near the Fermi energy E_F, come mainly from the outward movement of E_F with increasing x, and the effects of disorder in the B plane are small. In particular, our results show a sharp decline in both B and C p_x(y) states for 0.2≤x≤0.3. Our calculated variation in T_c of Mg(B_1−xC_x)₂ alloys is in qualitative agreement with the experiments.     

Structural and dielectric properties in the (Ba1−xCax)(Ti0.95Zr0.05)O3 ceramics

Lead-free (Ba_1−xCa_x)(Ti_0.95Zr_0.05)O₃ (x = 0.05-0.40) (BCZT) ceramics were prepared by solid-state reaction technique. XRD results show that the samples in the composition range of 0.05 ≤ x ≤ 0.25 exhibit pure perovskite structures and undergo a polymorphic phase transitions from orthorhombic to tetragonal phase around room temperature. The biphasic structures are detected at x ≥ 0.30 and the dielectric peaks become broad and dielectric constants decrease with increasing Ca content. Ca replacement at Ba site leads to diffuseness, whereas Ca occupancy at Ti site leads to decrease of the T_c.     

Effect of sintering atmosphere on the electrical and optical properties of (ZnO)1−x(MnO2)x NTCR ceramics

Nominal composition of (ZnO)_1−x(MnO₂)_x (0.005≤x≤0.2) ceramics have been prepared by the standard solid-state reaction method in three different sintering atmospheres: Ar, air, and reductive atmosphere. The effect of sintering atmosphere on the electron spin resonance (ESR), negative temperature coefficient of resistivity (NTCR), and photoluminescence (PL) properties of (ZnO)_1−x(MnO₂)_x ceramics has been investigated in detail. The results demonstrate that the sintering atmosphere has significant effects on the ESR signals of (ZnO)_1−x(MnO₂)_x; the NTCR of the samples sintered in air is larger than those sintering in Ar and reductive atmosphere; the deep-level PL related to oxygen vacancy increases when sintered in the reductive atmosphere.     

Enhanced piezoelectric properties near the morphotropic phase boundary in lead-free (1-x)(Bi0.5K0.5)TiO3-xBi(Ni0.5Ti0.5)O3 ceramics

Lead-free piezoelectric ceramics of the composition (1-x)(Bi_0.5K_0.50)TiO₃-xBi(Ni_0.50Ti_0.50)O₃ or (1-x)BKT-xBNiT (when x = 0–0.20 mol fraction) were prepared by a conventional mixed-oxide method and sintered at 1050 °C for 4 h. The effects of BNiT content on the phase equilibria, and the dielectric, ferroelectric and piezoelectric properties were systematically investigated. High density sintered specimens (5.71–6.12 g/cm³) were obtained for all compositions. X-ray diffraction patterns showed that all BKT-BNiT samples exhibited a single perovskite phase which confirms that BNiT and BKT formed a solid solution up to x = 0.20. A morphotropic phase boundary (MPB) separating a BKT-rich tetragonal phase and a BNiT pseudo-cubic phase was identified over the compositional range 0.05 < x < 0.10, where enhanced electrical properties were observed. The optimum dielectric properties (ε_r = 1710, tanδ = 0.036), ferroelectric properties (P_r = 16.6 μC/cm², E_c = 22.5 kV/cm and R_sq = 0.86) and piezoelectric properties (d₃₃ = 288 pC/N, S_max = 0.22% and d^*₃₃ = 313 pm/V) were observed with a relatively high T_m ∼ 304 °C within this MPB region. Overall, these results indicate that the BKT-BNiT ceramic system is a promising lead-free piezoelectric candidate for further development for actuator applications.     

Modified structure and electrical properties of BSZT doped KNN hybrid ceramic

Lead free (1?x)(K_0.5Na_0.5)NbO₃–x(Ba_0.9Sr_0.1)(Zr_0.1Ti_0.9)O₃ [(1?x)KNN–xBSZT] (x=0,0.02,0.04 and 0.06) ceramic were synthesized by a solid-state reaction method and the effects of BSZT doping on the electrical properties of KNN have been studied. X-ray diffraction (XRD) indicates that all the samples have single-phase perovskite structure and addition of BSZT forms a morphotropic phase boundary (MPB) i.e. the coexistence of orthorhombic and tetragonal phase in the region 0.02≤x≤0.04. Field emission scanning electron microscopy (FESEM) indicates the reduction in the grain size with the addition of BSZT. Small broadening in the dielectric peak arises at higher concentration of BSZT. The value of remnant polarization at x=0.04 is found to be higher than any other value of x except x=0 and also results in enhancement of dielectric constant at room temperature. Thereby it makes it useful for application at room temperature.     

Evolution from relaxor-like dielectric to ferroelectric in Ba[(Fe0.5Nb0.5)1−xTix]O3 solid solutions

Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ (x=0.2,0.4,0.6,0.8,0.85,0.9 and 0.95) solid solutions were synthesized by a standard solid-state reaction technique. X-ray diffraction at room temperature and dielectric characteristics over a broad temperature and frequency range were evaluated systematically. The structure of Ba[(Fe_0.5Nb_0.5)_1−xTi_x]O₃ solid solutions changed from cubic to tetragonal with increasing x. A Debye-like dielectric relaxation following the Arrhenius law similar to that in Ba(Fe_0.5Nb_0.5)O₃ was observed at lower temperature in the composition range 0.2≤x≤0.8, while the relaxor ferroelectric, diffused ferroelectric and normal ferroelectric behavior were observed for x=0.85,0.9 and 0.95, respectively. The process of the evolution of relaxor-like dielectric to ferroelectric suggested the changing from dilute polar micro-domains to polar micro-domains, polar micro/macro-domains and then polar macro-domains in the present ceramics.