BPDA/PPD/OTOL聚酰亚胺纤维的力学性能、形貌和结构

在3,3’,4,4’-联苯四酸二酐(BPDA)和对苯二胺(PPD)体系中引入3,3’-二甲基联苯胺(OTOL),显著改善了纤维的力学性能。当n(PPD)∶n(OTOL)=70∶30时,纤维的拉伸强度可达到改性前的2倍,其拉伸强度和拉伸模量分别为1.50和80 GPa。SEM照片显示了纤维的断面为圆形且没有孔穴,也没有明显的"皮芯"结构和原纤结构。WAXD和SAXS分析表明,纤维的轴向堆积和分子链取向在热牵伸过程中得到改善。     

Properties,Morphology and Structure of BPDA/PPD/TFMB Polyimide Fibers

The mechanical properties of fibers were notably improved by incorporating 2,2′-bis(trifluoromethyl)- benzidine(TFMB) into 3,3′,4,4′-biphenyltetracarboxylic dianhydride(s-BPDA) and p-phenylenediamine(PPD) backbone. The best strength and modulus of BPDA/PPD/TFMB polyimide(PI) fiber(diamine molar ratio of PPD/TFMB= 90/10) were 1.60 and 90 GPa, respectively, which was over two times that of BPDA/PPD PI fiber. SEM image showed that the cross-section of fibers at each stage was round and voids free. Besides, the “skin-core” and microfibrillar structure were not observed. The thermal properties of PI fibers were also investigated. The results showed that the fibers owned excellent thermal stability, moreover, the structural homogeneity of fibers were significantly improved by heat-drawn stage. The T_g values were found to be around 300℃ by dynamic mechanical analysis(DMA). Wide angle X-ray diffraction(WAXD) and small angle X-ray scattering(SAXS) experiments indicated that the order degree of longitudinal and lateral stacks, the molecular orientation and the structural homogeneity of fibers were improved in the preparation process of fibers.     

Small‐angle X‐ray scattering investigation of carbon nanotube‐reinforced polyacrylonitrile fibers during deformation

Structural changes during deformation in solution‐ and gel‐spun polyacrylonitrile (PAN) fibers with multi‐ and single‐wall carbon nanotubes (CNTs), and vapor‐grown carbon nanofibers were investigated using synchrotron X‐ray scattering. Previously published wide‐angle X‐ray scattering (WAXS) results showed that CNTs deform under load, alter the response of the PAN matrix to stress, and thus enhance the performance of the composite. In this article, we find that the elongated scattering entities that give rise to the small‐angle X‐ray scattering (SAXS) in solution‐spun fibers are the diffuse matrix‐void interfaces that follow the Porod's law, and in gel‐spun fibers these are similar to fractals. The observed smaller fraction of voids in the gel‐spun fibers accounts for the significant increase in the strength of this fiber. The degree of orientation of the surfaces of the voids is in complete agreement with those of the crystalline domains observed in WAXS, and increases reversibly upon stretching in the same way as those of the crystalline domains indicating that the voids are integral parts of the polymer matrix and are surrounded by the crystalline domains in the fibrils. The solution‐spun composite fibers have a larger fraction of the smaller (<10 nm) voids than the corresponding control PAN fibers. Furthermore, the size distribution of the voids during elongation changes greatly in the solution spun PAN fiber, but not so in its composites. The scattered intensity, and therefore the volume fraction of the voids, decreases considerably above the glass transition temperature (T_g) of polymer. Implications of these observations on the interactions between the nanotubes and the polymer are discussed. © 2009 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 47: 2394–2409, 2009     

液态丙烯腈低聚物修复聚丙烯腈基碳纤维微孔缺陷

提出一种全新的缺陷修复的方法,即将聚丙烯腈基(PAN)碳纤维T300在液态丙烯腈低聚物(LAN)中浸渍后,再进行预氧化和碳化热处理,可以将T300的拉伸强度提高25%.应用二维小角X射线散射(SAXS)法可以计算出LAN修复缺陷前后T300微孔缺陷的长度(L)、横截面尺寸(lp)、取向角(Beq)、相对体积(Vrel)的变化,结果表明碳纤维的拉伸性能越好,微孔的长度、取向角、相对体积含量越小.T300拉伸性能的提高是由于缺陷修复的结果.应用BET比表面积法、扫描电子显微镜(SEM)表征LAN修复缺陷前后T300的比表面积以及表面形貌的变化,结果表明,T300在LAN中浸渍并经过预氧化和碳化热处理,比表面积变小,表面缺陷明显减少.进一步验证LAN对碳纤维中的微孔缺陷具有修复作用.应用X射线光电子能谱(XPS)法表征LAN修复前后T300表面化学成分的变化,结果表明,LAN修复后含氧官能团(C―OH,C=O,HO―C=O)显著增加,有利于增强碳纤维与树脂基体之间的相互作用,从而提高碳纤维的力学性能.     

预氧化过程中张力对聚丙烯腈预氧化纤维微缺陷结构的影响

本文报道用同步辐射二维小角X射线散射(2D\|SAXS)研究预氧化过程中张力对PAN纤维缺陷的影响.     

2D SAXS/WAXD analysis of pan carbon fiber microstructure in organic/inorganic transformation

Structure of PAN fibers during pre-oxidation and carbonization was studied using two dimensional small angle X-ray scattering/wide angle X-ray diffraction(2D SAXS/WAXD).The SAXS results show that during pre-oxidation between 180 ℃ and 275 ℃,the volume content of microvoids increases with the temperature increasing,which may be one of reasons for the decrease of tensile strength of pre-oxidized fibers.253 ℃ was the critical transition temperature,the length,diameter,aspect ratio and orientation distribution of microvoids increased with temperature before this temperature and decreased after this temperature.After the high temperature carbonization,lots of spindly microvoids formed.WAXD patterns demonstrate that the crystallite size of PAN fibers first increased before 230 ℃ and then decreased with the increase of temperature during the pre-oxidation.The diffraction peak of PAN fibers at 2θ≈ 17° almost disappeared at the end of preoxidation while the diffraction peak of aromatic structure at 2θ≈ 25° appeared at 253 ℃.During carbonization,the peak intensity at 2θ≈ 25° increased apparently due to the formation of graphite structure.The results obtained give a deep understanding of the microstructure development in the PAN fibers during pre-oxidation and carbonization,which is important for the preparation of high performance carbon fibers.     

聚丙烯腈基碳纤维及其原丝中的微孔尺寸分布

利用二维小角X射线散射技术(SAXS)研究了聚丙烯腈基碳纤维及其原丝的微孔结构。结合逐级切线法、对数正态分布及麦克斯韦分布函数对2类实验样品内部微孔的尺寸分布进行了分析。结果表明,2类样品中的孔结构具有显著差别,原丝微孔在4~8 nm范围内分布比较集中,碳纤维中微孔的分布区域则移向1.3~1.8 nm。散射数据显示出明显的分形特征,碳纤维与其原丝的孔分形维数分别为1.33和1.55,表明原丝中具有较大的孔隙缺陷。相对于原丝,碳纤维微孔尺寸分布走向均匀和集中,前者则表现出比后者更宽的尺寸分布。就拟合方法而言,逐级切线法的解析手段容易引入误差,低角区的纤维表面散射和高角区的噪音容易对其结果造成影响。正态分布得到了比较窄的尺寸分布,但对于低尺寸区域孔隙的拟合不理想。麦氏分布在一定程度上弥补了以上不足,能够较好地拟合两类纤维样品中微孔的分布状况。     

应用弦长度分布函数研究中孔分子筛的精细结构

弦长度分布(chord length distribution, 简称CLD)可以用来描述几何对象(球形颗粒、柱状孔、薄片等)的大小、形状和空间排布等特点. 原理上, 弦长度分布正比于由小角散射所得的相关函数的二次微分, 因此可以由相对散射强度进行计算. 在结构研究中, 将实验所得弦长度分布与理论计算某种确定几何体所得高度准确的弦长度分布进行比较, 可以获知对象的特征几何结构. 本文以中孔氧化硅分子筛为研究对象, 介绍了弦长度分布的计算方法, 以此精确计算了中孔分子筛的孔径分布, 得到了分子筛表面有机官能化对孔径的影响规律.     

Nucleation, structure and lamellar morphology of isotactic polypropylene filled with polypropylene-grafted multiwalled carbon nanotubes

Polypropylene-based nanocomposites filled with polypropylene-grafted multiwalled carbon nanotubes (PP-g-MWNT) were compared to PP samples filled with pristine MWNT. The effect of such additives on the structure and morphology of the polymer matrix was studied by small angle X-ray scattering (SAXS), wide angle X-ray diffraction (WAXD), polarized light optical microscopy (PLOM) and differential scanning calorimetry (DSC). PP-g-MWNT allowed a more efficient and unhindered crystallization at a lamellar level, while MWNT disrupted the order of lamellar stacks, probably because of their tendency to aggregate. A common trend of tensile properties and lamellar morphology as a function of filler content was noted in the series filled with functionalized carbon nanotubes.     

Tailoring the morphology and properties of waterborne polyurethanes by the procedure of cellulose nanocrystal incorporation

Polyurethane waterborne synthesis was performed using a two-step method, commonly referred to as a prepolymer method. Nanocomposites based on waterborne polyurethane and cellulose nanocrystals were prepared by the prepolymer method by altering the mode and step in which the nanofillers were incorporated during the polyurethane formation. The morphology, structural, thermal, and mechanical properties of the resulting nanocomposite films were evaluated by Fourier transform infrared spectroscopy (FTIR), small angle X-ray scattering (SAXS), scanning electron microscopy (SEM), and tensile tests. FTIR results indicated that the degree of interaction between the nanofillers and the WPU through hydrogen bonds could be controlled by the method of cellulose nanocrystal incorporation. Data obtained from SAXS experiments showed that the cellulose nanocrystals as well as the step of the reaction in which they are added influenced the morphology of the polyurethane. The reinforcing effect of CNCs on the nanocomposites depends on their morphology.     

Morphology and thermomechanical properties of well-defined polyethylene-<Emphasis Type="Italic">graft</Emphasis>-poly(<Emphasis Type="Italic">n</Emphasis>-butyl acrylate) prepared by atom transfer radical polymerization

The morphology and thermomechanical properties of well-defined polyethylene-graft-poly(n-butyl acrylate) (PE-g-PBA) copolymers prepared via atom transfer radical polymerization were investigated. Differential scanning calorimetry (DSC), small angle X-ray scattering (SAXS), wide angle X-ray scattering (WAXS), dynamic mechanical measurement and large deformation tensile tests were performed on the graft copolymers and the results were compared with the behavior of the polyethylene macroinitiator. The existence of both crystalline polyethylene segments and amorphous poly(n-butyl acrylate) segments in the copolymers leads to microphase separation and unique thermomechanical behavior. Strong microphase separation was observed by DSC and X-ray diffraction studies. Correlation of morphology and thermomechanical properties was also studied using dynamic mechanical measurement and large deformation tensile tests.Dedicated to Prof. E. W. Fischer on the occasion of his 75th birthday     

Effects of ultra-high temperature treatment on the microstructure of carbon fibers

The microcrystalline structure and microvoid structure in carbon fibers during graphitization process(2300-2700 °C) were characterized employing laser micro-Raman scattering(Raman), X-ray diffraction(XRD), small angle X-ray scattering(SAXS), and high-resolution transmission electron microscopy(HR-TEM). The crystalline sizes(L_a, L_c) increased and interlayer spacing(d_(002)) decreased with increasing heat treatment temperature(HTT). The microvoids in the fibers grew up and contacted to the neighbors with the development of microcrystalline. In addition, the preferred orientation of graphite crystallite along fiber axis decreased and microvoids increased. The results are crucial for analyzing the evolution of microstructure of carbon fibers in the process of heat treatment and important for the preparation of high strength and high modulus carbon fibers.     

Strukturuntersuchungen an naßersponnenen Polyacrylnitrilfasern nach der Gefriertrocknung

Zusammenfassung An unterschiedlich verstreckten und hydrothermisch nachbehandelten, danach gefriergetrockneten Polyacrylnitril-Gelfasern (PAN) wurden Messungen der Röntgenkleinwinkelstreuung (RKWS), Röntgenweitwinkelstreuung (RWWS) und Tieftemperatur-Gassorption (TTGA) durchgeführt. Die RKWS-Messungen zeigen, daß sowohl in den isotropen als auch in den orientierten Proben eine exponentialstatistische Verteilung der Form und Größe der Inhomogenitäten (Hohlräume, Cluster) vorliegt, welche durch die Kohärenzlängel _c bestimmt wird. Eine erhöhte Röntgenabsorption wurde bei den verstreckten Proben festgestellt. Die Analyse der aus der Kohärenzlänge und den Volumsanteilen der Phasen berechneten charakteristischen RK WS-Parameter (z.B. innere Oberfläche, Durchschußlänge) ergibt, daß jede Behandlung der Gelfasern eine Zu- oder Abnahme der etwa gleich großen Hohlräume verursacht (nucleotic change). Das relative Ausmaß dieser Veränderungen wird besprochen.Der Vergleich mit den Ergebnissen der TTGA an den gleichen Fasern zeigt, daß die Tendenzen bei der spezifischen Oberfläche und dem Porenvolumen (Zu- bzw. Abnahme) bei beiden Methoden annähernd gleich sind. Die Absolutwerte des Hohlraumvolumens unterscheiden sich aber z.T. um den Faktor 40. Dies führt zur Schlußfolgerung, daß mit der RK WS Faserbereiche als Hohlräume erfaßt werden, die bei der TTGA nicht angezeigt werden, weil sie für das Meßgas unzugänglich sind.

---

Structural studies on wet-spun freeze-dried polyacrylonitrile fibers

Summary Polyacrylonitrile fibers (PAN) were drawn to different extents, hydrothermally aftertreated, and at last freeze-dried. The products were studied by small angle X-ray scattering (SAXS), wide angle X-ray scattering (WAXS), and low temperature gassorption (LTGS). The SAXS data show that the shape and the size of the inhomogeneities (voids, clusters) have an exponential statistical distribution determined by the correlation lengthl _c, both in the isotropic fibers and in the fiber-oriented ones. It has also been observed that stretching always causes a higher X-ray absorption. An analysis of the characteristic SAXS parameters (e.g., internal surface, mean chord length), which were calculated from the correlation length and the volume fractions of the phases, evidences that in all samples an augmentation or diminution of the number of the voids with nearly the same shape and size takes place (nucleotic change). Its relative number has been pointed out.Comparison with the results of the LTGS investigations at the same fibers shows that the tendencies of the specific surface and porosity (increase, decrease) are approximately the same with both methods. However, the absolute values of void volume differ in some cases by the factor 40. This leads to the conclusion that the SAXS method records domains of these fibers as voids which are not registered by LTGS (voids not accessible for the gas).

Herrn em.o.Univ. Prof. Dr.Josef Schurz zum 70. Geburtstag gewidmet     

大孔交联聚苯乙烯的分形结构研究

采用小角Ｘ－射线散法测定大孔交联聚苯乙烯树脂的结构,发现大多数大孔交联聚苯乙烯在数纳米至数十纳米的标度尺寸范围内具有分形结构,分形维数介于２和３之间。本研究还进一步探讨了交联度、致孔剂,功能基化反应及后处理对大孔交联聚苯乙烯分形结构的影响。     

辐照聚乙烯的熔融和重结晶

用差示扫描量热法（ＤＳＣ），小角Ｘ－射线散射（ＳＡＸＳ），广角Ｘ－射线衍（ＷＡＸＤ）等考察了辐照聚乙烯的熔融和重结晶，辐照破坏了聚乙烯结晶结构，使其熔融温度、结晶度均随辐照剂量的增加而降低，将辐聚乙烯熔融再结晶，其重结晶度、熔融温度随辐照剂量而下降的幅度较大，其原因被归结为片晶劈裂。     

Selective uptake of different proteins by annealed and quenched cationic spherical polyelectrolyte brushes

The selective uptake of bovine serum albumin (BSA) and β-glucosidase (β-G) by annealed and quenched cationic spherical polyelectrolyte brushes (SPB) was systematically studied by combining turbidimetric titration, dynamic light scattering and small angle X-ray scattering (SAXS). These two kinds of SPB consist of a same polystyrene core and a dense shell of poly (2-aminoethyl methacrylate hydrochloride) (PAEMH) and poly [2-(methacryloyloxy) ethyl] trimethylammonium chloride (PMAETA), respectively. Results reveal that the adsorption/desorption of proteins on SPB can be easily controlled by changing external conditions (pH and ionic strength). For a particular annealed or quenched SPB, there is a significant difference of the interaction pH regions between the brush and the two proteins, and this difference can be tuned by ionic strength. At low ionic strength, quenched brushes were more suitable for selective adsorption of BSA and β-G, while annealed brushes performed better at high ionic strength. SAXS analysis demonstrated that volume exclusion effect played a remarkable role in protein uptake by both SPB, and larger proteins were more likely to be adsorbed on the outer layer of the brush. The unique core-shell structure and controllable chain types make SPB an excellent candidate in selective adsorption/separation of proteins of different sizes.     

Structure and properties of gel-spun ultra-high molecular weight polyethylene fibers with high gel solution concentration

The gel-spun ultra-high molecular weight polyethylene(UHMWPE) fibers were prepared at the industrial production line with different gel solution concentrations of 15 wt%, 18 wt% and 24 wt%. The difference in ultimate structure and mechanical properties of UHMWPE fibers for different gel solution concentrations were analyzed by tensile testing, differential scanning calorimetry(DSC), wide angle X-ray diffraction(WAXD) and small angle X-ray scattering(SAXS). With the increase of gel solution concentration, the ultimate mechanical properties of UHMWPE fibers were decreased and the crystallization and orientation of UHMWPE fibers became inferior. Besides, both the average shish length(〈L _(shish)〉) and shish misorientation(B_φ) of UHMWPE fibers were decreased with the increase of gel solution concentration. In addition, the appropriate increase of spinning temperature led to the further optimization of the ultimate structure and mechanical properties of UHMWPE fibers.     

Structure and properties of polyimide fibers containing benzimidazole and Amide Units

Co‐polyimide (co‐PI) fibers with outstanding mechanical properties were fabricated via thermal imidization of polyamic acids, derived from a new design of combining the amide and benzimidazole diamine monomers, 4‐amino‐N‐(4‐aminophenyl)benzamide (DABA) and 2‐(4‐aminophenyl)‐5‐aminobenzimidazole (BIA), with 3,3′,4,4′‐biphenyltetracarboxylic dianhydride (BPDA). The crystalline structure and micromorphology of the prepared co‐PI fibers were investigated by synchrotron wide‐angle X‐ray diffraction (WAXD) and small‐angle X‐ray scattering (SAXS). The two‐dimensional WAXD spectra imply that the co‐PI fibers possess a structure between smectic‐like and three‐dimensionally ordered crystalline phase, and all the obtained fibers are highly oriented along the fiber axis. SAXS patterns exhibit a pair of meridional scattering streaks for the homo‐PI (BPDA/BIA) fiber, suggesting the presence of periodic lamellar structure. The incorporation of DABA into the polymer chains destroyed the lamellar structure but led to smaller size of microvoids upon increasing DABA moiety, based on SAXS analysis. The co‐PI fibers, with the molar ratio of BIA/DABA being 7/3, exhibited the optimum tensile strength and modulus of 1.96 and 108.3 GPa, respectively, attributed to the well‐defined ordered and dense structure. The chemical structure and molecular packing significantly affected the thermal stability of fibers, resulting in the different glass transition temperatures (T_g) from 350 to 380 °C. © 2014 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2015 , 53, 183–191     

Zur Porenanalyse anPAN-Fasern durch Röntgenkleinwinkelanalyse und Tieftemperaturgassorptionsmessungen

Both inner surface and void system of technicalPAN-fibres (Wolpryla 65) have been determined by means of low temperature gas sorption, and by X-ray small angle analysis. We find similar trends for both methods, but different absolute values. These differences are explained by structural considerations. A model for the structure of the voids system is derived from the X-ray data.

Herrn Prof. Dr.H. Janeschitz-Kriegl anläßlich seines 60. Geburtstages gewidmet     

Properties of oligopyrrole doped dodecylbenzene–sulfonic acid prepared with different oxidants in reversed microemulsion

The calcium silicate systems were prepared by sol–gel methods—varying the synthesis conditions (precursor solutions, chemical compositions, catalysts, temperature and time of aging and heat treatment). The precursors of sol–gel procedures were calcium nitrate and tetraetoxysilane. Acetic acid, water, ammonia and nitric acid were applied as catalysts. The atomic and supramolecular structures of calcium silicate products have been varied from amorphous to crystalline phases depending strongly on the preparation conditions. The structures were investigated in atomic range with Fourier transform infrared (FTIR), X-ray diffraction (XRD) and in supramolecular ranges with small angle X-ray scattering (SAXS), ultra small angel X-ray scattering (USAXS) measurements. The mechanical properties could be most efficiently improved by heat treatments (min. 600 °C) and a post-treatment with tetraetoxysilane (TEOS). The mechanical strength of bulk biomaterials has been controlled by Brinell hardness test.