Aerodynamic flow vectoring of a wake using asymmetric synthetic jet actuation

This paper reports an experimental investigation on the wake of a blunt-based, flat plate subjected to aerodynamic flow vectoring using asymmetric synthetic jet actuation. Wake vectoring was achieved using a synthetic jet placed at the model base 2.5?mm from the upper corner. The wake Reynolds number based on the plate thickness was 7,200. The synthetic jet actuation frequency was selected to be about 75?% the vortex shedding frequency of the natural wake. At this actuation frequency, the synthetic jet delivered a periodic flow with a momentum coefficient, C _??, of up to 62?%. Simultaneous measurements of the streamwise and transverse components of the velocity were performed using particle image velocimetry (PIV) in the near wake. The results suggested that for significant wake vectoring, vortex shedding must be suppressed first. Under the flow conditions cited above, C _?? values in the range of 10?C20?% were required. The wake vectoring angle seemed to asymptote to a constant value of about 30° at downstream distances, x/h, larger than 4 for C _?? values ranging between 24 and 64?%. The phase-averaged vorticity contours and the phase-averaged normal lift force showed that most of the wake vectoring is produced during the suction phase of the actuation, while the blowing phase was mostly responsible for vortex shedding suppression.     

Effect of novel synthetic jet on wake vortex shedding modes of a circular cylinder

A novel actuator signal achieved by changing the ratio of the suction duty cycle to the blowing duty cycle is adopted to enhance the control effect of the synthetic jet for the flow around a circular cylinder. The suction duty cycle factor k defined as the ratio between the time duration of the suction cycle and the blowing cycle and the equivalent momentum coefficient C_μ are introduced as the determining parameters. The synthetic jet is positioned at the rear stagnation point in order to introduce symmetric perturbations upon the flow field. The proper orthogonal decomposition (POD) technique is applied for the analysis of the spanwise vorticity field. Increasing the suction duty cycle factor, the momentum coefficient is enhanced, and thus a stronger and larger scale synthetic jet vortex pair with a higher convection velocity is generated. The synthetic jet vortex pair interacts with the spanwise vorticity shear layers behind both sides of the cylinder, resulting in the variations of the wake vortex shedding modes at Re=950: for k=0.25, C_μ=0.148, vortex synchronization at the subharmonic excitation frequency with antisymmetric shedding mode; for 0.50≤k≤1.00, 0.213≤C_μ≤0.378, vortex synchronization at the excitation frequency with the symmetric or antisymmetric shedding modes; for 2.00≤k≤4.00, 0.850≤C_μ≤2.362, vortex synchronization at the excitation frequency with symmetric shedding mode. Hence, the control effect of the synthetic jet upon the wake vortex of a circular cylinder can be enhanced by increasing the suction duty cycle factor so as to increase the momentum coefficient. This is also validated at a higher Reynolds number Re=1600.     

Modified flapping jet for increased jet spreading using synthetic jets

The present paper is an experimental investigation, using a PIV system, on modified rectangular jet flow co-flowing with a pair of synthetic jets placed symmetrically with respect to the geometric centerline of the main flow. The objective was to determine the optimal forcing conditions that would result in jet spreading beyond what would be obtained in a simple flapped jet. The main jet had an exit Re_h = 36,000, based on the slot height, h. The synthetic jets were operated in a periodic manner with a periodic momentum coefficient of about 3.3% and at a frequency of the main jet preferred mode. A short, wide angle diffuser of half angle of about 45° was attached to the main jet. Generally for the vectored jet, much of the flow features found here resembled those reported in the literature except that the deflection angle in this study increased with downstream distances inside the diffuser and then remained roughly unchanged thereafter. Larger jet spreading was achieved when the main jet was subjected to simultaneous actuation of the synthetic jets but the flow did not achieve the initial jet spreading that was observed in the vectored jet. Further jet spreading was achieved when the synthetic jets were alternately actuated in which each synthetic jet was actuated for a number of cycles before switching. This technique allowed the jet to flap across the flow between transverse positions larger than what would be obtained in a simple flip-flop jet. Under the present flow geometry and Reynolds number, it was found that when the ratio f_s/f_al, where f_s is the synthetic actuation frequency and f_al is the alternating frequency, was larger than 10, the mean streamwise velocity of the main jet had two peaks symmetrically placed with respect to the jet axis and the jet had the appearance of flowing into two streams each moving nearly parallel to the diffuser wall. For a value of f_s/f_al of about 10, the optimal value in this study, the desired flow properties were achieved in that, the mean velocity was nearly uniform with an increase in the jet width compared to the simultaneous actuations, and the jet flapping was more effective in redistributing and homogenizing the turbulent kinetic energy across the main jet.     

Control of the corner separation in a compressor cascade by steady and unsteady plasma aerodynamic actuation

This paper reports experimental results on using steady and unsteady plasma aerodynamic actuation to control the corner separation, which forms over the suction surface and end wall corner of a compressor cascade blade passage. Total pressure recovery coefficient distribution was adopted to evaluate the corner separation. Corner separation causes significant total pressure loss even when the angle of attack is 0°. Both steady and unsteady plasma aerodynamic actuations suppress the corner separation effectively. The control effect obtained by the electrode pair at 25% chord length is as effective as that obtained by all four electrode pairs. Increasing the applied voltage improves the control effect while it augments the power requirement. Increasing the Reynolds number or the angle of attack makes the corner separation more difficult to control. The unsteady actuation is much more effective and requires less power due to the coupling between the unsteady actuation and the separated flow. Duty cycle and excitation frequency are key parameters in unsteady plasma flow control. There are thresholds in both the duty cycle and the excitation frequency, above which the control effect saturates. The maximum relative reduction in total pressure loss coefficient achieved is up to 28% at 70% blade span. The obvious difference between steady and unsteady actuation may be that wall jet governs the flow control effect of steady actuation, while much more vortex induced by unsteady actuation is the reason for better control effect.     

Control of diffuser jet flow: turbulent kinetic energy and jet spreading enhancements assisted by a non-thermal plasma discharge

An axisymmetric air jet exhausting from a 22-degree-angle diffuser is investigated experimentally by particle image velocimetry (PIV) and stereo-PIV measurements. Two opposite dielectric barrier discharge (DBD) actuators are placed along the lips of the diffuser in order to force the mixing by a co-flow actuation. The electrohydrodynamic forces generated by both actuators modify and excite the turbulent shear layer at the diffuser jet exit. Primary air jet velocities from 10 to 40 m/s are studied (Reynolds numbers ranging from 3.2 to 12.8 × 10⁴), and baseline and forced flows are compared by analysing streamwise and cross-stream PIV fields. The mixing enhancement in the near field region is characterized by the potential core length, the centreline turbulent kinetic energy (TKE), the integrated value of the TKE over various slices along the jet, the turbulent Reynolds stresses and the vorticity fields. The time-averaged fields demonstrate that an effective increase in mixing is achieved by a forced flow reattachment along the wall of the diffuser at 10 m/s, whereas mixing enhancement is realized by excitation of the coherent structures for a primary velocity of 20 and 30 m/s. The actuation introduces two pairs of contra-rotating vortices above each actuator. These structures entrain the higher speed core fluid toward the ambient air. Unsteady actuations over Strouhal numbers ranging from 0.08 to 1 are also studied. The results suggest that the excitation at a Strouhal number around 0.3 is more effective to enhance the turbulence kinetic energy in the near-field region for primary jet velocity up to 30 m/s.     

Phase-resolved PIV measurements in a transitional plane wall jet: a numerical comparison

The transitional process of a forced plane wall jet is studied both experimentally and numerically. Experimentally, Particle Image Velocimetry (PIV) and laser-sheet/smoke flow-visualization techniques are implemented to provide an overall understanding of the flow features. Numerically, time-accurate computational results are obtained by solving the two-dimensional, unsteady Navier–Stokes equations. Comparison of PIV data and two-dimensional computed results shows excellent agreement in the early stages of transition, demonstrating that the numerical study can be used to complement the experimental one. The results show that, under the influence of external excitation, linear-instability growth is bypassed and a discrete shear-layer vortex is formed in the immediate vicinity of the nozzle exit. This vortex interacts with the boundary-layer vorticity, leading to the formation of another vortex in the inner layer. These two vortices form a vortex couple that for high forcing convects downstream in a stable manner. By adoption of either a no-slip or a slip boundary condition in the numerical computation, it is determined that the flow development is relatively insensitive to the imposed wall-boundary condition. This seems to suggest that the physical mechanism leading to the formation of the boundary-layer vortex is an inviscid rotational one. Received: 14 February 1998/Accepted: 11 August 1998     

Eddy-Viscosity and Stress-Transport Turbulence Models in Application to a Plane Synthetic Jet

A two-dimensional unsteady plane jet is computed using four turbulence models. The strain field generated by the ‘synthetic’ (reciprocating) jet under consideration contains regions of strong normal and shear straining, while vortex pairs formed by the issuing jet are highly rotational. Turbulence closures at the eddy-viscosity level (standard k???ε and two-timescale models) and two stress-transport closures (the ‘basic’ model and a two-component-limit scheme) are examined against experimental data. It is found that the extreme nature of the strain environment presents a severe challenge to the models tested; in particular, fundamental weaknesses in the constitutive equation of linear eddy viscosity models are highlighted. An additional term in the dissipation rate equation of the two-timescale model is found to hinder the formation of clearly defined starting vortex pairs which play a critical role in determining the near-field pattern of synthetic jet development. The stress-transport models are able to reproduce measured turbulence quantities with a greater degree of accuracy, and the two-component-limit formulation shows an improvement over the basic model.     

Mechanism of compressor airfoil boundary layer flow control using nanosecond plasma actuation

The flow control effects of nanosecond plasma actuation on the boundary layer flow of a typical compressor controlled diffusion airfoil are investigated using large eddy simulation method. Three types of plasma actuation are designed to control the boundary layer flow, and two mechanisms of compressor airfoil boundary layer flow control using nanosecond plasma actuation have been found. The plasma actuations located within the laminar boundary layer flow can induce a small vortex structure through influencing on the density and pressure of the flow field. As the small vortex structure moves downstream along the blade surface with the main flow, it can suppress the turbulent flow mixing and reduce the total pressure loss. The flow control effect of the small vortex structure is summarized as wall jet effect. Differently, the plasma actuation located within the turbulent boundary layer flow can act on the shear layer flow and induce a large vortex structure. While moving downstream, this large vortex structure can suppress the turbulent flow mixing too.     

Numerical simulation on micromixer based on synthetic jet

This paper studied a concept of micromixer with a synthetic jet placed at the bottom of a rectangular channel. Due to periodic ejections from and suctions into the channel, the fluids are mixed effectively. To study the effects of the inlet velocity, the jet intensity and frequency, and the jet location on the mixing efficiency, 3-D numerical simulations of the micromixer have been carried out. It has been found that when the jet intensity and the frequency are fixed, the mixing efficiency increases when Re 〈 50, and decreases when Re 〉 50 with the best mixing efficiency achieved at Re = 50. When the ratio of the jet velocity magnitude to the inlet velocity is taken as 10 and the jet frequency is 100 Hz, the mixing index reaches the highest value. It has also been found that to get better mixing efficiency, the orifice of the synthetic jet should be asymmetrically located away from the channel＇s centerline.     

The Effect of Wall Normal Actuation on a Turbulent Boundary Layer

In this work, a series of direct numerical simulations are conducted to study the effect of wall normal spanwise homogeneous wall actuation on a turbulent boundary layer. The moving boundary is represented by a boundary data immersion technique. A parametric study was performed, varying the actuator length, the wall normal actuation amplitude and the actuation frequency. It was found that localized actuation, relying only on wall motion instead of requiring a plenum in the case of synthetic jets, generated a net momentum flux jet affecting the flow not only in the immediate vicinity of the actuator but also for a significant distance downstream. The cases with an actuator velocity of \( u^{+}_{act}=?20.1 \) showed a particularly pronounced effect on the boundary layer and resulted in a recirculation region.     

Powered resonance tubes: resonance characteristics and actuation signal directivity

The powered resonance tube (PRT) actuator and its variants are new developments in active flow control (AFC) technology. The PRT is attractive because it has no moving parts and can produce acoustic tones that have amplitudes greater than 150 dB over a large frequency bandwidth. The first part of this paper deals with the resonance characteristics of the PRT as a function of the operating parameters such as jet-to-tube spacing (Sp), tube depth (d), and nozzle pressure ratio (NPR). It was found that: (1) at low NPR (3.33), the PRT resonates at discrete combinations of spacing and depth. (2) Using theoretical estimates for predicting shock cell lengths, one could observe a correlation between the theoretical prediction for shock cell length and the spacing at which the PRT resonates. (3) At high NPR (4.29), for a fixed depth, the PRT resonates at virtually all spacings. (4) The frequency at which the PRT resonates remains approximately constant, regardless of spacing. The second part of the study focused on examining the directivity of the acoustic radiation from the PRT—significant for developing orientation strategies of the PRT with respect to the target flow in the end application. The directivity of the fundamental PRT tone and that of its harmonics were studied for a variety of resonance frequencies, both separately as well as cumulatively. It was found that the fundamental part of the actuation signal radiated predominantly in the downstream direction of the jet for low resonance frequencies. As the resonance frequency was increased from 3 to 12 kHz, the directivity changed from downstream of the jet to vertically upward, and finally upstream of the jet at the higher frequencies.

---

不定原点喷嘴射流中流体物理的实验研究(英文)

为了能够更好地了解不定源喷嘴(indeterminate origin nozzle)射流中的物理过程,本文应用平面激光诱导荧光技术对一个大尺度的水射流进行了实验研究。流场显示的实验结果表明不定源喷嘴在射流的剪切层引入了蘑菇形反向旋转的涡对。这些涡的矢量方向与射流方向相同或相反,被称为流向涡(streamwise vortex)。由于射流中存在开尔文-亥姆霍兹不稳定,每当一个横向涡(spanwise vortex,即涡的矢量方向与射流方向垂直)从喷嘴脱流时会产生瞬时的低压,该瞬时低压促使向内发展的流向涡对在喷嘴的凹槽处生成。这些涡对在向下游流动的过程中会重组并在喷嘴的尖峰面生成向外发展的涡对。这些流向涡极大地影响了射流的发展。流向涡与横向涡的相互作用促使射流更早地发展成为湍流。由于流向涡同时也在射流中引入了径向的剪切流动,因此导致了更多的湍流生成从而增强了射流与周围流体的混合。     

Modification of the near wake behind a finite-span cylinder by a single synthetic jet

Modification to the flow field about a finite-span cylinder of low-aspect ratio (AR = 3) by a single synthetic jet, mounted normal to the cylinder axis, was studied experimentally using surface-mounted pressure taps, stereoscopic particle image velocimetry (SPIV), and constant-temperature anemometry. The synthetic jet altered the circulation about the cylinder and created a large spanwise change to the surface pressure, much greater than the dimensions of its orifice. SPIV measurements in the near wake showed that the synthetic jet enhances mixing of the downwash from the cylinder free end with the wake deficit, vectoring and narrowing the wake. The synthetic jet penetrates through the streamwise vorticity, enhancing mixing within the wake and reducing the power associated with the shedding frequency, St = 0.155, except below the vortex dislocation, where the shedding frequency was increased to that corresponding to a quasi-two-dimensional cylinder, St = 0.22.     

不定原点喷嘴射流中流体物理的实验研究

为了能够更好地了解不定源喷嘴（indeterminate origin nozzle）射流中的物理过程，本文应用平面激光诱导荧光技术对一个大尺度的水射流进行了实验研究。流场显示的实验结果表明不定源喷嘴在射流的剪切层引入了蘑菇形反向旋转的涡对。这些涡的矢量方向与射流方向相同或相反，被称为流向涡（streamwise vortex）。由于射流中存在开尔文一亥姆霍兹不稳定，每当一个横向涡（spanwisevortex，即涡的矢量方向与射流方向垂直）从喷嘴脱流时会产生瞬时的低压，该瞬时低压促使向内发展的流向涡对在喷嘴的凹槽处生成。这些涡对在向下游流动的过程中会重组并在喷嘴的尖峰面生成向外发展的涡对。这些流向涡极大地影响了射流的发展。流向涡与横向涡的相互作用促使射流更早地发展成为湍流。由于流向涡同时也在射流中引入了径向的剪切流动，因此导致了更多的湍流生成从而增强了射流与周围流体的混合。     

Manipulation of Large-Scale Vortical Structures and Mixing in a Coaxial Jet with Miniature Jet Actuators Toward Active Combustion Control

Manipulation of large-scale vortical structures and associated mixing in a methane-air coaxial jet is carried out by using miniature jet actuators installed on the inner surface of the annular nozzle. The periodic radial miniature jet injections are achieved with a rapid-response servo-valve. The spatio-temporal primary jet structures are investigated through phase-locked 2C-PIV (2 Component Particle Image Velocimetry) and stereoscopic-PIV. It is found that intense ring-like vortices are produced perfectly in phase with the periodic miniature jet injections regardless of the valve-driven frequency f_v examined. When the Strouhal number St_v, which is defined with f_v, is larger than unity, the ring-like vortices are densely formed and thus methane/air mixing is prompted with low periodic fluctuation. The diameter of the vortices becomes small as St_v is increased, so that the transport range of the inner methane and outer air fluids can be controlled by changing St_v. In addition, the evolution of counter-rotating vortex pair is also observed in the cross-sectional plane. These streamwise vortices are directly formed as a result of the radial miniature jet injection, which leads to entrainment of the ambient fluid near the primary jet shear layer, and they also contribute to the mixing enhancement. Moreover, it is demonstrated that coaxial jet flame characteristics such as carbon monoxide (CO) emission and flame holding can be drastically improved under different equivalence ratios by the present jet control scheme.     

Feedback control of vortex shedding from two tandem cylinders

The effect of feedback control on vortex shedding from two tandem cylinders in cross-flow is investigated experimentally. The objective is to reduce the downstream cylinder response to vortex shedding and turbulence excitations. Feedback control is applied to a resonant case, where the frequency of vortex shedding coincides with the resonance frequency of the downstream cylinder, and to a nonresonant case, in which the shedding frequency is about 30% higher than the downstream cylinder resonance frequency. A “synthetic jet” issuing through a narrow slit on the upstream cylinder is employed to impart the control effect to the flow. The effect of open-loop control, using pure tones and white noise to activate the synthetic jet, is also examined. It is demonstrated that feedback control can significantly reduce the downstream cylinder response to both vortex shedding and turbulence excitations. For example, the cylinder response is reduced by up to 70% in the resonant case and 75% in the nonresonant case. Open-loop control also can reduce the cylinder response, but is less effective than feedback control. The frequency of vortex shedding is found to increase substantially when white noise is applied. This increase in the shedding frequency is higher than the largest frequency shift that could be produced by open-loop tone excitation.     

Effects of dual jets distance on mixing characteristics and flow path within a cavity in supersonic crossflow

A rectangular open cavity with upstream dual injectors at a freestream Mach number of 1.9 was investigated experimentally. To evaluate the effect of the distance between the jets, the flow characteristics were investigated using the high-speed schlieren photography, particle image velocimetry, and surface oil flow techniques. The dual jet distances of 18 and 54 mm were used. Unstable flow occurs over the cavity in all cases and is not improved by changing the distance between the dual jets. Although the distance between the dual jets does not influence the flow stability, the flow field varies decidedly depending on the dual jets distance. The enhancement of air mixing depends on the distance between the jets. A long dual jets distance was found to yield better mixing characteristics within the cavity than a short one. When the jets are further apart, the mainstream between two counter-rotating vortex pairs behind the jets flows strongly into the cavity because of the increased blow-down occurring between the vortex pairs. Additionally, a counterflow with a low velocity magnitude occurs behind the jets. Hence, mixing is enhanced within the cavity by effects of the opposed flow. When the jet pairs are closer to each other, the counter-rotating vortex pairs are in contact; as a result, the blow-down effect does not occur between them. The flow drawn into the cavity from the mainstream is supplied from the sides of the test section into the cavity.     

Control of flow distortion in offset diffusers using trapped vorticity

Controlled concentrations of trapped vorticity within an offset, subsonic (M_AIP ≤ 0.7) diffuser are explored for active suppression of flow distortion in joint experimental and numerical investigations. The coupling between trapped vorticity, used to model boundary-layer separation, and secondary-flow vortices is manipulated using an array of fluidic oscillating jets, which are spanwise distributed just upstream of the trapped vortex. Actuation energizes the separated shear layer, reducing the size of separation and effecting an earlier reattachment of the boundary layer, which favorably effects the flow field downstream of reattachment. It is shown that optimal interactions between actuation and the trapped vortex fully suppress the central vortex pair, and redistributes the residual vorticity around the diffuser's circumference. This results in a 68% reduction in circumferential distortion at the Aerodynamic Interface Plane (AIP), using an actuation mass flow rate that is only 0.25% of the diffuser mass flow rate.     

Further Examination of the Mechanism of Round Synthetic Jets in Delaying Turbulent Flow Separation

This paper reports the findings from a further study of the 2D and stereo PIV data obtained in the interaction zone between the separated turbulent boundary layer over a 2D ramp and round synthetic jets by the authors. The synthetic jets are operated at two actuation frequencies with one being close to the natural frequency of the separated shear layer. Both the triple decomposition technique and Q-criterion are employed to investigate how the separated flow responds to the passage of different parts of the vortical structures produced by the synthetic jets during an actuation cycle at different synthetic jet operating conditions. An attempt is made to explain the observed differences in the ways that the separated flow responds to the actuation of synthetic jets at the two actuation frequencies. A better understanding of the mechanism of flow separation delay using round synthetic jets is obtained, leading to a more complete physical model describing the interaction mechanism.