膨胀柱壳恒定应变率的本构关系

考虑到金属柱壳膨胀过程中随机裂纹萌生对测试结果的可能干扰,设计了预置有中心穿透圆孔的柱壳样品,采用多普勒光纤探针测量系统获得了柱壳外壁更优的径向速度历史。基于膨胀柱壳实验中固有的非恒定应变率现象,研究了获得恒定应变率下本构方程的方法,并采用改进后的本构方程确定方法,获得了20钢恒定应变率下的应力应变关系。     

A New Experimental Technique for the Multi-axial Testing of Advanced High Strength Steel Sheets

This paper deals with the development of a new experimental technique for the multi-axial testing of flat sheets and its application to advanced high strength steels. In close analogy with the traditional tension-torsion test for bulk materials, the sheet material is subject to combined tension and shear loading. Using a custom-made dual actuator hydraulic testing machine, combinations of normal and tangential loading are applied to the boundaries of a flat sheet metal specimen. The specimen shape is optimized to provide uniform stress and strain fields within its gage section. Finite element simulations are carried out to verify the approximate formulas for the shear and normal stress components at the specimen center. The corresponding strain fields are determined from digital image correlation. Two test series are performed on a TRIP-assisted steel sheet. The experimental results demonstrate that this new experimental technique can be used to investigate the large deformation behavior of advanced high strength steel sheets. The evolution of the yield surface of the TRIP700 steel is determined for both radial and non-proportional loading paths.     

散体介质SHPB被动围压试验体应力计算的理论修正方法

SHPB被动围压试验为探究散体介质在爆炸和冲击荷载作用下的力学行为提供了一个行之有效的方法。针对相关试验设计和计算中存在的弊端和不足,借助经典板壳理论将SHPB被动围压试验中用于约束散体介质的刚性套筒简化为受均匀带状内压作用的圆柱形壳体。理论计算了套筒径向位移、环向应变与均匀带状内压及套筒几何、力学参数的关系,得到了套筒径向位移、环向应变沿其轴向的分布规律;分析了套筒长度、厚度、内外径以及均匀带状内压宽度之间等无量纲几何参数对计算结果的影响;将理论计算结果与试验和数值模拟结果进行对比,验证了理论计算结果的正确性。本文中提出的理论修正方法可为指导散体介质SHPB被动围压试验提供参考。     

基于SHPB的UHPC冲击试验径向惯性效应分析

为探讨UHPC试件惯性效应对SHPB加载过程的影响,采用大型有限元分析软件LS-DYNA从试件直径、长径比以及恒应变率加载等角度出发,开展了相应的数值模拟与分析。通过对软件中Karagozian-Case-Concrete (KCC)损伤模型参数取值进行优化,建立了基于SHPB技术的UHPC材料冲击压缩数值模型并与试验验证。在此基础上,开展不同UHPC试件直径、长径比以及有无整形器下的参数分析,探讨其对SHPB试验中径向惯性效应的影响。结果表明:(1)为实现加载过程中一维应力传播和UHPC试件应力平衡,试件直径建议按0.90～0.95倍杆件直径取值;(2) UHPC试件长径比对试件加载过程中的应力平衡影响较小,但综合试件中钢纤维分布均匀性以及破坏前一维应力传播,建议按0.35～0.45取值;(3)实现恒应变率加载是UHPC材料在SHPB冲击试验中消除径向惯性效应的重要前提。     

Standard Uncertainty Evaluation for Dynamic Tensile Properties of Auto-Body Steel-Sheets

This paper is concerned with the standard uncertainty of the true stress–true strain curve as the tensile properties of auto-body steel sheets at intermediate strain rates ranged from 1 to 100 s^?1. A procedure to obtain true stress–true strain data is properly designed for the experiment and data acquisition. An analytic model is then established to evaluate the standard uncertainty of the measurand. The measurand in this case is the true stress which is a function of the input quantities: the tensile load; the initial length, the thickness and the width of a specimen; and the deformed length of a specimen. Sources of uncertainties of the input quantities are evaluated for the high speed tensile test with their associated sensitivity coefficients. Uncertainty of the stress data acquired is also considered in the procedure of the fast Fourier transform (FFT) smoothing process used to remove unnecessary signals acquired from experiments. Image analysis using a high speed camera is carried out to measure deformation of the specimen during high speed tensile tests with proper uncertainty evaluation. A combined standard uncertainty is evaluated from the uncertainties of the input quantities as well as the influence factor for the true stress of auto-body steel sheets at intermediate strain rates. Consequently, the true stress–true strain data are obtained with proper standard uncertainty evaluation.     

爆炸与电磁加载下无氧铜环、柱壳的断裂模式转变

考虑断面收缩率、局域断裂应变以及平均断裂应变,并基于电磁膨胀环、爆炸膨胀环(柱壳)实验平台,研究了高纯无氧铜(TU1)环及柱壳在高应变率载荷下的膨胀断裂行为。采用高速摄影技术拍摄柱壳外壁的膨胀断裂形貌演化过程,用于确定柱壳平均断裂应变;利用激光干涉测速技术获得样品径向膨胀速度历史,用于确定加载应变率;利用样品的全回收测量及微观表征,确定了无氧铜环、柱壳的局域断裂应变及断裂模式。实验表明,随着应变率的增加,TU1材料的平均断裂应变增加,断面的收缩程度加剧,并在应变率约为1.0×104 s-1附近会出现明显的断裂模式转变,断面收缩率出现量级上的跳跃,从100变化至约103,局域断裂应变呈现明显的分区现象。     

轴、侧向同卸荷下砂岩力学特性影响的试验研究

本文以实际岩体工程为背景,利用WDT-1500 仪器开展了轴向、侧向同时卸荷条件下砂岩的三轴试验. 结果表明:轴、侧向同卸荷这种卸荷路径下,砂岩试样破坏时并没有出现应力峰值,为了定义试样的破坏强度,将最大与最小主应力差随最小主应力的变化关系曲线上应力跌落的拐点处的应力值定义为破坏强度. 砂岩变形初始段发生应力跌落和轴向应变回弹,破坏前无明显的弹性和屈服阶段;试验的过程中,砂岩的侧向变形明显大于轴向变形,其体积应变一直处于膨胀状态;相对于砂岩的常规三轴试验结果,试样破坏时的强度在轴向、侧向同时卸荷条件下有所降低. 初始轴压和初始围压对试样的力学特征有十分显著的影响,但围压的卸荷速率却并不显著. 砂岩的破坏特征主要是以张-拉为主的混合张剪的破坏.      

一种基于SHPB的冲击膨胀环实验技术

设计了一种基于分离式Hopkinson压杆(SHPB)的冲击膨胀环实验装置,实验装置包括一个液压腔,一侧为驱动活塞,另一侧为圆环试件封闭。对活塞施加轴向冲击,利用液体体积近似不可压缩的特性,通过液压腔截面积的大比例缩小,将较低速度的对活塞冲击转化为圆环试件沿径向的高速膨胀,驱动试件发生拉伸变形直至断(碎)裂。使用这种冲击膨胀装置,获得了LY12铝环在不同撞击速度下碎裂过程的初步结果。实验结果显示,随着撞击速度增大,圆环试件碎裂产生的碎片的尺度减小,试件的表观断裂应变增加。这为研究材料的动态拉伸碎裂问题提供了一种加载方式。     

基于SHPB装置的膨胀圆柱管实验技术

采用改进的SHPB实验装置对45钢薄壁金属圆柱管进行了膨胀断裂加载,完成了不同变形程度 (覆盖圆柱管整个变形及断裂过程)圆柱管的冻结回收实验。回收样品可用于断裂机理研究分析,通过数值模 拟辅助分析和实验数据拟合得到了圆柱管凸起处的径向应变、应变率和环向拉伸应力。通过在圆柱管端粘贴 应变片监测断裂信号的方式,准确判断了圆柱管凸起处发生断裂的时间,以及径向断裂应变、应变率和环向拉 伸断裂应力,在102~104s-1应变率范围内,SHPB实验装置可用于研究金属圆柱管膨胀断裂。     

An Embedded 3D Strain Tensor Sensor Based on the Eshelby’s Inclusion

A new design for an embedded strain sensor is proposed in this paper. Based on Eshelby’s inclusion model, it may be used to measure the full 3D strain or stress tensor within any solid body. Currently, common embedded strain sensors are only capable of 1D measurements. The spherical shape of our sensor allows the stress or strain that would exist in the structure without the sensor to be calculated with the aid of the Eshelby theorem (in the case of elastic behavior). We used fiber Bragg gratings to measure the deformation of the sphere - other techniques are also available. Experimental testing was performed in two settings. The first test measured the performance of a polymethylmethacrylate prototype under fluid pressure load. In a second test, a steel prototype sensor was embedded in a standardized concrete specimen under axial compression, and was successfully used to measure 3D strain in real conditions.     

大尺寸Hopkinson压杆及其应用

本文介绍了国内最大尺寸的SHPB装置;讨论了在大尺寸SHPB装置上测量混凝土类材料动态力学性能将会出现的几个问题;采取了在入射杆的打击端加设波形整形器,在试件与杆件之间加设万向头及在试件上直接测量应变等新的实验技术及采用新的数据处理方法,提高了试验结果的精确度和可信度;简要介绍了利用ф100 SHPB装置对四种体积含量(0,2%,4%和6%)钢纤维高强混凝土进行三种应变率(10~20/s,35~45/s和75~85/s)的冲击压缩实验。实验结果表明,钢纤维高强混凝土具有较强的应变率效应,其破坏应力、峰值应变随应变率增加而显著增加,弹性模量也随应变率增加而增加。另外,钢纤维含量对混凝土具有增韧效应,随着钢纤维含量的增加,其韧性增大,脆性降低。     

A new apparatus for studying mechanical behavior under pressure

Using a servohydraulic intensifier, a servohydraulic universal test machine and a novel test chamber, pressures of 750 MPa and axial stresses of almost any magnitude are simultaneously generated and applied to the gage section of a solid, cylindrical specimen. Under combined axial-stress/external-pressure loadings, a solid specimen experiences a truly three-dimensional, homogeneous stress state in which the axial stress equals σ₁ and the radial and circumferential stresses equal the negative of the pressure, —P. Through independent computer control of the pressure and axial stress, amterial behavior under monotonically and cyclically applied multiaxial stresses are investigated. This paper describes the experimental details of the test chamber design, high-pressure fluid production and sealing, load and strain measurement under high pressure, computer control and data acquisition. Experimental results obtained from triaxial monotonic tests on low alloy steel and triaxial cyclic tests on a Ni-Ti alloy using this unique apparatus are presented.     

Dynamic Tensile Testing of Soft Materials

Determination of dynamic tensile response of soft materials has been a challenge because of experimental difficulties. Split Hopkinson tension bar (SHTB) is a commonly used device for the characterization of high-rate tensile behavior of engineering materials. However, when the specimen is soft, it is challenging to design the necessary grips, to measure the weak transmitted signals, and for the specimen to achieve dynamic stress equilibrium. In this work, we modified the SHTB on the loading pulse, the equilibrium-monitoring system, and the specimen geometry. The results obtained using this modified device to characterize a soft rubber indicate that the specimen deforms under dynamic stress equilibrium at a nearly constant strain rate. Axial and radial inertia effects commonly encountered in dynamic characterization of soft materials are also minimized.     

Use of the Kolsky method for confined tests of soft soils

A modification of the well-know Kolsky method for dynamic tests is described for investigating the dynamic compressibility of soft soils. The modification consists of placing an axial compression soil specimen into a rigid steel jacket that confines its radial strain. Using this modification, experimental results for plasticine and clay are discussed. An automated system for processing the experimental data in order to plot stress-strain curves is also described.     

液压膨胀环动态拉伸碎裂的有限元模拟

液压冲击膨胀环实验平台能有效地实现韧性金属圆环在高应变率拉伸载荷作用下的动态断（碎）裂。本文采用流固耦合的有限元数值计算方法,模拟了实验过程中金属圆环在高压液体作用下的运动、变形和断裂现象。分析了装置和试件的接触应力对试件碎裂过程的影响并讨论了如何实现液压对试件的有效加载。计算结果表明,实验中的初始接触应力和液体的较长时间加载对试件的碎裂过程没有显著影响;在合理的加载条件下,液压膨胀环实验技术是研究固体动态拉伸碎裂的有效手段。     

Load-Inversion Device for the High Strain Rate Tensile Testing of Sheet Materials with Hopkinson Pressure Bars

A high strain rate tensile testing technique for sheet materials is presented which makes use of a split Hopkinson pressure bar system in conjunction with a load inversion device. With compressive loads applied to its boundaries, the load inversion device introduces tension into a sheet specimen. Two output bars are used to minimize the effect of bending waves on the output force measurement. A Digital Image Correlation (DIC) algorithm is used to determine the strain history in the specimen gage section based on high speed video imaging. Detailed finite element analysis of the experimental set-up is performed to validate the design of the load inversion device. It is shown that under the assumption of perfect alignment and slip-free attachment of the specimen, the measured stress–strain curve is free from spurious oscillations at a strain rate of 1,000 s^?1. Validation experiments are carried out using tensile specimens extracted from 1.4 thick TRIP780 steel sheets. The experimental results for uniaxial tension at strain rates ranging from 200 s^?1 to 1,000 s^?1 confirm the oscillation-free numerical results in an approximate manner. Dynamic tension experiments are also performed on notched specimens to illustrate the validity of the proposed experimental technique for characterizing the effect of strain rate on the onset of ductile fracture in sheet materials.     

基于PVDF薄膜传感器的猪肝动态压缩力学性能测试

瞬态冲击载荷作用下肝脏的力学响应是损伤生物力学的重要研究内容.本文提出了一种可用于软组织动态压缩力学特性测试的改进SHPB(分离式霍普金森压杆,Split Hopkinson Pressure Bar)方法.该方法采用PVDF(聚偏氟乙烯,Polyvinylidene Fluor)压电薄膜传感器测量实验过程中试件两端面...     

不同尺寸砂岩动态力学性质和应力平衡性的试验研究

采用大直径分离式霍普金森压杆系统获得的不同尺寸试样的实验冲击动态力学参数有差异,因此在直径100 mm压杆上进行了3种直径（50、75和100 mm）和5种长径比（0.4、0.5、0.6、0.8和1.0）的砂岩试样冲击试验,分析了不同尺寸试样应力-应变曲线和应变率曲线随尺寸的变化,提出了用于比较波形对齐重合度的波形叠加系数,并与应力平衡因子共同构建了动态应力平衡性研究体系,由此确定大直径霍普金森压杆试验的试样建议尺寸。同时,利用高速摄影机监测试样的动态破坏状况。结果表明:当长径比相同时,直径75与100 mm岩石试样的动态抗压强度测试值相近,直径50 mm试样具有更明显的长度效应;随着试样直径的增大,应变率曲线从单峰变为双峰;小尺寸试样更易发生轴向劈裂破坏,大尺寸试样受内部应力波叠加影响产生了较大的拉应力,易发生层裂拉伸和轴向劈裂的复合型破坏;对直径75 mm且长径比0.3~0.4的试样,波形对齐后重合度较高,在起始破坏前拥有充足的应力平衡时间,应变率加载效果较好。获得了砂岩试样冲击压缩试验的尺寸效应,可为大直径岩石试样的尺寸选择提供参考。     

Properties of rocks tested in one-dimensional compression

An apparatus has been developed and used to obtain static stress-strain data on rock and soil samples in one-dimensional compression. This paper describes the design and method of use, and reports test results obtained on several types of rock and sand specimens. A 4-in.-diam specimen with height up to 2 in. is contained in a thin-walled steel cylinder. This cylinder is contained in the main pressure vessel which has a pressure cavity surrounding the specimen. Load is applied through a load cell on top of the specimen by a hydraulic press. An operator maintains a constant zero balance on strain gages bonded to the thin, steel cylinder containing the specimen by pumping hydraulic fluid into the pressure cavity, thus nullifying the tendency of the test specimen to expand laterally as it is compressed axially. Axial load and deflection are recorded on anx?y plotter from signals received from the load cell and a deflectometer mounted on the load cell. This apparatus has been successfully used to obtain data on rocks to axial stresses of 75,000 psi and on sand to 30,000 psi. Test data for both rocks and sand are presented in this paper.     

基于数字图像的分离式霍普金森压杆实验中试件应变及两端应力的同步测量法

本文提出一种基于高速摄像和数字图像相关方法(DIC)的分离式Hopkinson压杆(SHPB)测量技术,从而实现试件应变和两端应力的同步测量。即在与试件接触的输入输出杆两端制作散斑,通过高速摄像获取SHPB实验过程中的散斑变形图像,由DIC测得各时刻试件的应变、输入输出杆端的应变(可直接换算为试件两端的应力)。由于试件和杆端的应变都是从同一张高速摄影的图像上分析得到的,因此它们是同步的。应用该方法对钢纤维混凝土试件的SHPB试验进行了测量,测量结果与传统应变片测量结果吻合,验证了该方法的可行性。该技术不仅实现了SHPB实验中试件应变和应力的同步测量,还将有助于直接检验各材料在SHPB实验中试件两端的力在实验过程中是否平衡。