Microwave-assisted extraction and ultrasonic extraction to determine polycyclic aromatic hydrocarbons in needles and bark of Pinus pinaster Ait. and Pinus pinea L. by GC-MS

Two different extraction strategies (microwave-assisted extraction (MAE) and ultrasonic extraction (USE)) were tested in the extraction of the 16 US Environmental Protection Agency (EPA) polycyclic aromatic hydrocarbons (PAHs) from pine trees. Extraction of needles and bark from two pine species common in the Iberian Peninsula (Pinus pinaster Ait. and Pinus pinea L.) was optimized using two amounts of sample (1 g and 5 g) and two PAHs spiking levels (20 ng/g and 100 ng/g). In all cases, the clean-up procedure following extraction consisted in solid-phase extraction (SPE) with alumina cartridges. Quantification was done by gas chromatography (GC) with mass spectrometry (MS), using five deuterated PAH surrogate standards as internal standards. Limits of detection were globally below 0.2 ng/g. The method was robust for the matrices studied regardless of the extraction procedures. Recovery values between 70 and 130% were reached in most cases, except for high molecular weight PAHs (indeno[1,2,3-cd]pyrene, dibenzo[a,h]anthracene and benzo[ghi]perylene). A field study with naturally contaminated samples from eight sites (four in Portugal and four in Catalonia, Spain) showed that needles are more suitable biomonitors for PAHs, yielding concentrations from 2 to 17 times higher than those found in bark. The levels varied according to the sampling site, with the sum of the individual PAH concentrations between 213 and 1773 ng/g (dry weight). Phenanthrene was the most abundant PAH, followed by fluoranthene, naphthalene and pyrene.     

PAH and PCB determination of the concentration gradient in moss Pleurozium schreberi near a highway,and seasonal variability at the background reference site

Moss (Pleurozium schreberi) was investigated as biomonitor of atmospheric polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). Samples were collected at a distance of 10, 50 and 100 m from a highway and were seasonally collected in a forest stand near a regional background air pollution station situated approximately 30 km from the highway. The samples from the background area were dried using two different techniques in parallel, air-drying and freeze-drying. Simultaneous pressurised liquid extraction of PAHs and PCBs was performed, followed by purification using gel permeation chromatography of the crude extract. The concentration of the 15 most important Environmental Protection Agency (EPA) PAHs was determined by gas chromatography coupled with ion-trap mass spectrometry with a selected ion storage acquisition programme, and the PCB concentrations were determined using a mass spectrometer operated in tandem mass spectrometry (MS/MS) mode. Acceptable recoveries and quality parameters for PAHs and PCBs were achieved with the use of pressurised liquid extraction followed by gel permeation chromatography. The detection limit was <0.76 ng g^?1 for PAHs and <0.04 ng g^?1 for PCBs. Possible contamination of the moss samples by 3-ring PAHs and PCBs in the atmosphere was found during air drying. Increased PAH and PCB concentrations caused by car engine exhausts and by asphalt and oil evaporation were found near the highway. Generally, the PAH and PCB concentrations in moss decreased exponentially with distance from the highway. The organic compound concentrations close to the background station showed seasonal fluctuations corresponding to the fluctuations in the local air temperature and particle concentration.     

Temporal variation of atmospheric polycyclic aromatic hydrocarbon concentrations in PM10 from the Kathmandu Valley and their gas-particle concentrations in winter

The concentrations of polycyclic aromatic hydrocarbons (PAHs) in particulate matter (PM) with a diameter <10 µm (PM₁₀, 50% cut off) were investigated in the Kathmandu Valley, Nepal, during 2003. In order to understand the dynamics of atmospheric PAHs in winter, the PAH concentrations in total PM and in the gaseous phase were investigated in the valley in December 2005. Total of 45 PAH compounds (∑45PAHs) were analysed by high-resolution gas chromatography/high-resolution mass spectrometry (HRGC/HRMS). In 2003, the ∑45PAH concentrations in PM₁₀ ranged between 4.3 and 89 ng m^?3 (annual average; 27 ± 24 ng m^?3). The average concentrations of ∑45PAHs in December 2005 were 210 ± 33 ng m^?3 in total PM and 430 ± 90 ng m^?3 in the gaseous phase. The ∑45PAH concentration in PM accounted for more than 30% of the sum of their particulate and gaseous forms. Phenanthrene (Ph) was the most predominant compound in the gaseous phase, whereas four- to seven-ring PAHs were predominant in total PM. The highest values of ∑45PAHs occurred in the winter and spring. Estimates of emission sources based on diagnostic molecular ratios showed that atmospheric PAHs in the Kathmandu Valley mainly originated from the exhaust gas of diesel engine. In the winter and spring, PAH pollution would be accelerated by the operations of brick kilns and the frequent formation of an atmospherically stable layer in the valley.     

Pressurised fluid extraction of polycyclic aromatic hydrocarbons and their polar oxidation products from atmospheric particles

An effective method utilising pressurised fluid extraction (PFE) to simultaneously extract polycyclic aromatic hydrocarbons (PAHs) and their polar oxidation products from atmospheric particulate matter (PM) is presented. The PFE method is advantageous over the traditional Soxhlet extraction due to its lower solvent consumption (9 mL compared to 90 mL) and shorter extraction time (15 min versus 18 h). Seventy compounds including PAHs and polar PAH oxidation products containing carbonyl (oxy-PAHs), hydroxyl (hydroxy-PAHs), and carboxylic acid (carboxy-PAHs) groups were targeted in the extraction of two different PM matrices: wood smoke (WS) and diesel exhaust (DE) PM. The PFE method was optimised and then compared to Soxhlet extraction for both PM matrices. The overall amounts of PAHs and their derivatives extracted from WS PM were slightly higher for the optimised PFE method (1849 ± 21 and 1863 ± 25 µg g^?1 with dichloromethane (DCM) and methanol (MeOH), respectively) than those obtained with Soxhlet extraction (1726 ± 33 and 1769 ± 22 µg g^?1 with DCM and MeOH, respectively). For DE PM (standard reference material (SRM) 2975) the overall amounts extracted by both methods were similar (average of 165 ± 6 µg g^?1), agreeing with previously published values. The detailed evaluation of extraction efficiencies for WS PM showed similar amounts for unfunctionalised PAHs (1100 µg g^?1) for both methods and solvents. For DE PM the mass yields for PAHs using PFE with DCM (62 ± 1 µg g^?1) were the highest and nearly 20% higher than those obtained with MeOH (53 ± 2 µg g^?1). The total mass yields of carboxy and hydroxy-PAHs from WS PM were also similar (412 ± 18 and 407 ± 11 µg g^?1) for PFE and Soxhlet with MeOH, and higher than when DCM was used (371 ± 5 and 379 ± 12 µg g^?1 for PFE and Soxhlet, respectively). For both matrices, the PFE yields for oxy-PAHs were higher than those obtained with Soxhlet.     

Concentrations and Sources of Polycyclic Aromatic Hydrocarbons in Water and Sediments from the Huaihe River,China

Surface water and sediments were collected from eleven locations on the middle region of Huaihe River to evaluate the environmental effects of urban and industrial activities. The concentrations of sixteen polycyclic aromatic hydrocarbons (PAHs) in water and sediments were between 1.2–5.1 µg/L and 72–139 ng/g, respectively. High levels of PAHs in water were recorded in comparison to those of other countries, while the concentrations in sediments were low to moderate levels. A weak positive correlation was observed (R² = 0.49, P = 0.13) between PAHs and total organic carbon in water. However, a significant positive correlation (R² = 0.79, P = 0.004) was found in sediments, which indicated that total organic carbon was a factor in PAH levels in sediments but not in water. The parent ratios were studied by principal component analysis that showed the PAHs from water were predominantly derived from coal combustion (34%), oil spills (49%), and vehicular emissions (17%), while the major PAH sources to sediments were coal combustion. Using the ecological toxic equivalency factor index, it was concluded that the PAHs levels may provide a potential risk in water but not in sediments.     

Behaviour of polycyclic aromatic hydrocarbons in dissolved,colloidal, and particulate phases in sedimentary cores

Solid-phase microextraction (SPME) has been successfully used for extracting polycyclic aromatic hydrocarbons (PAHs) from porewater samples from the Mersey Estuary, UK. The majority of the PAHs in porewater samples are associated with colloids due to the high DOC concentrations. The truly dissolved PAH concentrations varied from 66 to 1050?ng?L^?1 in core 2 and from 95 to 740?ng?L^?1 in core 3, and were dominated by naphthalene, fluoranthene, and pyrene. Although absent in the dissolved phase, the high-molecular-mass compounds were found in the colloid-associated fraction of porewater. PAHs in sediments arose from a range of compounds with 4- and 5-ring PAHs dominating. The partitioning of PAHs between sediment and porewater shows that PAHs are enriched in the sediment phase. When the soot carbon content was considered, predictions of the partition behaviour were found to agree more closely with the observed distribution. The results reiterate the importance of evaluating the speciation of organic pollutants in both porewater and sediments in order to accurately predict their environmental fate and potential toxicity.     

A Screening Method for Polycyclic Aromatic Hydrocarbons Determination in Sediments by Headspace SPME with GC–FID

A screening method for polycyclic aromatic hydrocarbons (PAHs) determination in sediment using headspace solid phase microextraction (HS-SPME) with gas chromatography–flame ionization detection was developed. In order to obtain the convenient experimental conditions for HS-SPME extraction an experimental design with two steps was done. 0.2 g of sediment and 85 µm polyacrylate fibre, 80 °C and 120 min were the chosen extractions conditions. The limit of detection (LOD) was from 0.8 ng g⁻¹ (fluoranthene) to 8 ng g⁻¹ (chrysene). The relative standard deviation (RSD) was less than 7.0%. Determination of PAHs in NRC–CNRC–HS–3B reference marine sediment showed good agreement with the certified values. The method was applied in the analysis of ten river and estuary surface sediments from Gipuzkoa (North Spain). PAHs total concentration ranged from 400 to 5,500 ng g⁻¹.

     

Analysis of polycyclic aromatic hydrocarbons in atmospheric particulate samples by microwave‐assisted extraction and liquid chromatography

A methodology based on microwave‐assisted extraction (MAE) and LC with fluorescence detection (FLD) was investigated for the efficient determination of 15 polycyclic aromatic hydrocarbons (PAHs) regarded as priority pollutants by the US Environmental Protection Agency and dibenzo(a,l)pyrene in atmospheric particulate samples. PAHs were successfully extracted from real outdoor particulate matter (PM) samples with recoveries ranging from 81.4 ± 8.8 to 112.0 ± 1.1%, for all the compounds except for naphthalene (62.3 ± 18.0%) and anthracene (67.3 ± 5.7%), under the optimum MAE conditions (30.0 mL of ACN for 20 min at 110°C). No clean‐up steps were necessary prior to LC analysis. LOQs ranging from 0.0054 ng/m³ for benzo(a)anthracene to 0.089 ng/m³ for naphthalene were reached. The validated MAE methodology was applied to the determination of PAHs from a set of real world PM samples collected in Oporto (north of Portugal). The sum of particulate‐bound PAHs in outdoor PM ranged from 2.5 and 28 ng/m³.     

Pressurized fluid extraction of polycyclic aromatic hydrocarbons using silanized extraction vessels

We have investigated the extraction efficiency of a pressurized fluid extraction system using an Ottawa sand matrix, soils and a certified reference material (HS-6) spiked with the 16 polycyclic aromatic hydrocarbon (PAHs) associated with method EPA 8100. Acceptable recoveries were achieved for all PAHs using a nominal sand concentration of 2.0 μg.g^-1. However, similar experiments that were conducted at a concentration of 0.20 μg.g^-1 afforded poor recoveries and poor reproducibility for the six-ring PAHs indeno(1,2,3-cd)pyrene, dibenz(a)anthracene, and benzo(ghi)perylene. These were not adequately addressed by the use of indeno(1,2,3-cd)pyrene-d12 and benzo(g,h,i)perylene-d12 surrogates. Silanization of vessels using dichlorodimethylsilane adequately passivates the system but is only required for the high surface area retention frits. Replicate analyses at concentrations of 200 and 20 ng.g^-1 demonstrated that detection limits in the low ppb range (ng.g^-1) are achieved for Ottawa sand, dry soil and soil with moisture contents up to a mass fraction of 30 %. Such performance is consistent with the analytical requirements of the Canadian Sediment Quality Guidelines. Improved analyte recoveries were also observed for the certified reference material HS-6 which were further improved by increasing extraction temperatures from 100 to 150 °C.

A 110 Year Sediment Record of Polycyclic Aromatic Hydrocarbons Related to Economic Development and Energy Consumption in Dongping Lake,North China

A sedimentary record of the 16 polycyclic aromatic hydrocarbon (PAH) pollutants from Dongping Lake, north China, is presented in this study. The influence of regional energy structure changes for 2–6-ring PAHs was investigated, in order to assess their sources and the impact of socioeconomic developments on the observed changes in concentration over time. The concentration of the ΣPAH₁₆ ranged from 77.6 to 628.0 ng/g. Prior to the 1970s, the relatively low concentration of ΣPAH₁₆ and the average presence of 44.4% 2,3-ring PAHs indicated that pyrogenic combustion from grass, wood, and coal was the main source of PAHs. The rapid increase in the concentration of 2,3-ring PAHs between the 1970s and 2006 was attributed to the growth of the urban population and the coal consumption, following the implementation of the Reform and Open Policy in 1978. The source apportionment, which was assessed using a positive matrix factorization model, revealed that coal combustion was the most important regional source of PAHs pollution (>51.0%). The PAHs were mainly transported to the site from the surrounding regions by atmospheric deposition rather than direct discharge.     

Gas chromatography–tandem mass spectrometry analysis of 52 monohydroxylated metabolites of polycyclic aromatic hydrocarbons in hairs of rats after controlled exposure

A method based on gas chromatography–tandem mass spectrometry after derivatization with N-tert-butyldimethylsilyl-N-methyltrifluoroacetamide was developed for the analysis of monohydroxylated polycyclic aromatic hydrocarbons (OH-PAHs) in hair. The method focused on 52 target compounds corresponding to two- to six-ring monohydroxylated metabolites of polycyclic aromatic hydrocarbons (PAHs). The limits of quantification ranged from 0.2 to 50 pg mg^?1. The method was then applied to the analysis of hair samples collected from rats exposed to 12 PAHs at 0.01, 0.1, and 1 mg kg^?1, by intraperitoneal injection, for 28 days. The results of this study confirm that these metabolites can be incorporated in hair after intraperitoneal administration of the corresponding parent compound. Only 20 of the 52 metabolites were actually detected in hair samples and corresponded to nine parent PAHs. The mean concentrations of OH-PAHs in rat hair samples exposed to PAHs at 1 mg kg^?1 ranged from 0.6?±?0.2 pg mg^?1 for 8-hydroxybenzo[b]fluoranthene to 6.7?±?1.0 pg mg^?1 for 1-hydroxypyrene. The results also demonstrated that hair pigmentation has no influence on the concentration of most OH-PAHs. This animal experiment confirmed the incorporation of PAH metabolites in hair and demonstrated that the method was sufficiently sensitive to detect low levels of exposure to PAHs. These results confirmed the usefulness of hair analysis in the biomonitoring of human exposure to PAHs.

Development and certification of a coal fly ash certified reference material for selected polycyclic aromatic hydrocarbons

The development and certification of a coal fly ash certified reference material (CRM) for polycyclic aromatic hydrocarbons (PAH) is described; this is the first natural matrix CRM for organic environmental analysis in China. The homogeneity and stability of this material have been tested by HPLC. The concentrations of several PAH were determined by use of two independent, different methods – solvent extraction–HPLC analysis with UV detection coupled with fluorescence detection (FLD) and solvent extraction, isolation with a silica column, and GC analysis with flame ionization detection (FID). Five certified values were determined: phenanthrene 7.1 ± 2.6 μg g^–1, anthracene 2.0 ± 0.8 μg g^–1, fluoranthene 7.4 ± 1.9 μg g^–1, pyrene 7 ± 2 μg g^–1, and benzo[a]pyrene 1.3 ± 0.3 μg g^–1. Reference values for several other PAH are also suggested.     

Determination of polycyclic aromatic hydrocarbons in the needles of a Scotch pine (<Emphasis Type="Italic">Pinus sylvestris</Emphasis> L.), a biomonitor of atmospheric pollution

A procedure was developed for the determination of polycyclic aromatic hydrocarbons (PAH) in the needles of a Scotch pine (Pinus sylvestris L.), which is characterized by the simple and efficient sample preparation. The procedure involves the steps of the extraction of PAH with n-hexane on ultrasonic irradiation, the precipitation of concomitant cereous components from the extract on its cooling, the purification of the PAH fraction on a cartridge with silica gel (0.5 g), and the redissolution of the concentrated eluate in methanol. The quantitative determination of PAH (15 compounds including 13 priority) with the use of chromatography-mass spectrometry in the selective ion detection mode exhibits the interlaboratory precision of the results of the PAH determination V _Rl = 0.059–0.088 for the concentration of PAH in needles from 0.3 to 600 ng/g and a detection limit of 0.06 ng/g (signal-to-noise ratio = 3; mass of the sample for extraction was 10 g). The accumulation levels of PAH in the Scotch pine needles were presented; the needles were first studied as a biomonitor of atmospheric pollution over the southern part of the Baikal natural territory.     

Hollow-fibre liquid-phase microextraction: a simple and fast cleanup step used for PAHs determination in pine needles

A new, fast and simple cleanup procedure, based on hollow-fibre liquid-phase microextraction (HF-LPME) is described here, used for the determination of 13 polycyclic aromatic hydrocarbons (PAHs) in complex pine needle samples. Initially, pine needle samples were sonicated in a 20 mL aqueous solution having a 20% (v:v) acetone content and 5 mL of the sonicated liquid extract was then used for the HF-LPME cleanup step. Different experimental parameters (namely: type of organic solvent used as acceptor phase, effect and type of co-solvent, salt addition, sample agitation and sampling time) were controlled and optimized based on the response of GC-MS instrument under the SIM mode. Under the optimized experimental conditions found the typical chromatograms obtained revealed that despite the very complex matrix of pine needles the HF-LPME cleanup step greatly reduced if not eliminated the presence of interferents, resulting in chromatograms which contained very cleanly separated and readily evaluable PAH peaks. In addition, the proposed method was found to be linear in the concentration 10-2000 ng g⁻¹ for most target analytes and the limits of detection for a S/N = 3 ranged between 0.01 and 0.95 ng g⁻¹ (dry weight). Furthermore, the repeatability and reproducibility were also found good. Finally, the proposed method was applied for the analysis of real pine needle samples taken for different parts of the island of Crete.     

Pressurised liquid extraction of polycyclic aromatic hydrocarbons from gas and particulate phases of atmospheric samples

Pressurised liquid extraction (PLE) was applied to determine the atmospheric levels of 16 polycyclic aromatic hydrocarbons (PAHs) in the gas and particulate phases. The method involved high‐volume air sampling with quartz fibre filters (QFFs) and polyurethane foam (PUF) plugs and analytes were subsequently extracted from the samples by PLE, and determined with GC‐MS. We optimised the PLE conditions for the solvent, the number of cycles and extraction temperature. Recoveries were higher than 90% for most compounds. Method LODs and LOQs were between 0.001 and 0.02 ng/m³ and between 0.01 and 0.05 ng/m³. Air samples were taken from a site in the region of Tarragona in Catalonia, Spain, where one of the largest petrochemical complexes in southern Europe is located. The total concentration of PAHs were from 6.7 to 27.66 ng/m³, with predominant levels of PAHs appearing in the gas phase (48–81%), and an average level of benzo[a]pyrene, the most carcinogenic PAH, of 0.86 ng/m³.     

n-Alkanes, PAHs and surfactants in the sea surface microlayer and sea water samples of the Gerlache Inlet sea (Antarctica)

Sea surface microlayer (SML) and sea water samples (SSW) collected in the Gerlache Inlet Sea (Antarctica) were analysed for n-alkanes and polycyclic aromatic hydrocarbons (PAHs). The SML is a potential enrichment site of hydrophobic organic compounds compared to the underlying water column. Total concentration ranges of n-alkanes and PAHs (dissolved and particulate) in subsurface water (− 0.5 m depth) were 272-553 ng l^− 1 (mean: 448 ng l^− 1) and 5.27-9.43 ng l^− 1 (mean: 7.06 ng l^− 1), respectively. In the SML, the concentration ranges of n-alkanes and PAHs were 353-968 ng l^− 1 (mean: 611 ng l^− 1) and 7.32-23.94 ng l^− 1 (mean: 13.22 ng l^− 1), respectively. To evaluate possible PAH contamination sources, specific PAH ratios were calculated. The ratios reflected a predominant petrogenic input. A characterisation of surface active substances was also performed on SML and SSW samples, both by gas bubble extraction, and by dynamic surface tension measurements. Results showed a good correlation between n-alkanes, PAHs and refractory organic matter.     

Comparison of immunoassay and gas chromatography-mass spectrometry for measurement of polycyclic aromatic hydrocarbons in contaminated soil

Polycyclic aromatic hydrocarbons (PAHs) are frequently encountered in the environment and may pose health concerns due to their carcinogenicity. A commercial enzyme-linked immunosorbent assay (ELISA), was evaluated as a screening method for monitoring PAHs at contaminated sites. The ELISA was a carcinogenic PAH (C-PAH) RaPID assay testing kit that cross-reacts with several PAHs and utilizes benzo[a]pyrene (BaP) as a calibrator. Soil samples were extracted with 50% acetone in dichloromethane (DCM) for analysis by ELISA and gas chromatography-mass spectrometry (GC-MS). The overall method precision was within ±30% for ELISA and within ±20% for GC-MS. Recovery data for spiked soils ranged from 46 to 140% for BaP as determined by ELISA. Recoveries data of the GC-MS surrogate standards, 2-fluorobiphenyl and chrysene, were greater than 70%. The GC-MS procedure detected a total of 19 priority PAHs (2-6-ring PAHs) including seven probable human carcinogens (4-6-ring B2-PAHs). The ELISA results were compared to GC-MS summation results for the total 19 target PAHs as well as for the subset of the seven B2-PAH compounds. For all soil samples, the PAH concentrations derived from ELISA were greater than the sum of B2-PAH concentrations obtained by GC-MS. ELISA determinations were also frequently greater than the results obtained by GC-MS for the total 19 PAH compounds. This discrepancy can be expected, since the ELISA is a screening assay for the detection of several related PAHs while the GC-MS procedure detects priority PAH compounds. Thus, only a subset of PAHs (e.g. 19 PAHs) in the soil samples were measured by GC-MS while additional PAHs, including alkylated PAHs, and PAH derivatives have been demonstrated to be cross-reactive in the C-PAH ELISA. Results of paired tests show that the PAH data from ELISA and GC-MS methods are significantly different (P<0.001), but highly correlated. The ELISA data had a strong positive relationship with the GC-MS summation data for the B2-PAHs as well as for the 19 PAHs targeted by the GC-MS method. Results indicate that the ELISA may be useful as a broad screen for monitoring PAHs in environmental samples.     

Polycyclic aromatic hydrocarbon and ionic compositions of atmospheric bulk deposition samples at a national park under the influence of intense barbecue smoke

The main aim of this study was to present the effects of barbecue smoke on a small-scale environment, a national park under the influence of intense barbecue smoke, and to scientifically support the sustainable usage of the park. Twelve-weekly bulk deposition samples were collected directly at the barbecuing area, and the samples were analysed for 16 US EPA’s priority PAH compounds and major ions. The mean concentrations of the individual PAHs in the bulk deposition samples ranged from 11.8 ng L^?1 (Ane) to 1085 ± 581 ng L^?1 (IcdP). The most frequently observed PAH compounds in the bulk deposition samples were Np, Anp, Flr, Phe, An, Flu, BkF, BaP and IcdP. The mean total PAH deposition fluxes were determined as 3.6 ± 5.6 µg m^?2 day^?1. The chloride, potassium and the sulphate fluxes were determined as 145.2 ± 267.8 µg m^?2 day^?1, 182.9 ± 291.9 µg m^?2 day^?1, and 111.9 ± 65.9 µg m^?2 day^?1, respectively. Dominant ions in the bulk deposition samples were potassium ion, chloride and sulphate which addressed as the fingerprint of barbecue grilling.     

Rapid and simplified method for the quantitative analysis of polycyclic aromatic hydrocarbons, lipid biomarkers and organochlorine compounds in marine settling particles

We report on a distinctly improved method for the determination of polycyclic aromatic hydrocarbons (PAHs), lipid biomarkers and organochlorine compounds (OCs) in sediment trap studies involving large numbers of samples of limited particle amounts (20–50?mg). It is based on gas chromatography hyphenated to mass spectrometry. One protocol enables analysis of PAHs and lipids, the other that of the OCs. Both have identical extraction and clean-up procedures, the first involving alkaline hydrolysis and the latter hydrolysis with concentrated sulfuric acid. The limits of detection and quantification for PAHs are 0.1–5.7 and 0.1–9.5?ng?g^?1, respectively. For lipids, they are 0.01–0.12 and 0.01–0.21?μg?g^?1, and for OCs they are 0.1–1.0 and 0.3–1.1?ng?g^?1. The method was applied to sediment traps deployed in the northwestern Mediterranean and provided useful fingerprints to understand sources, ways of transport and fates of these species.

DNA Nanogels To Snare Carcinogens: A Bioinspired Generic Approach with High Efficiency

Polycyclic aromatic hydrocarbons (PAHs) are combustion‐related pollutants and are ubiquitous in the environment, including in sources of drinking water. Upon contact with DNA, stable PAH–DNA adducts form rapidly as the first step towards their toxic effects. In this work, we prepared hydrophilic DNA nanogels to exploit this generic complexation process as a biomimetic scavenging method. This approach relies on interaction between PAHs and the complete network that constitutes the water‐swollen nanogels, and is not restricted to interfacial adsorption. Up to 720 μg of PAH per gram of DNA nanogel are taken up, meaning that 1 mg of DNA nanogel is sufficient to purify a liter of water containing the critical PAH concentration for cancer risk (600 ng L^?1). As a result of short diffusion pathways, PAH uptake is rapid, reaching 50 % loading after 15 minutes. Beyond PAHs, DNA nanogels may be useful for the generic detoxification of water containing genotoxins, since most known molecules that strongly associate with DNA are mutagenic.