Determination of five polar herbicides in water samples by ionic liquid dispersive liquid-phase microextraction

A simple, rapid and efficient ionic liquid based on dispersive liquid-phase microextraction (IL-DLPME) method was developed for the determination of three triazine and two phenylurea herbicides in water samples. IL (1-hexyl-3-methylimidazolium hexafluorophosphate [C₆MIM][PF₆]) that dispersed completely into the water solution under controlled temperature was used as the extraction solvent. The analytes were easily concentrated into the ionic liquid phase. This technique combined the process of extraction and concentration of the analytes into one step and avoided use of the more common, toxic organic solvents. The factors affecting the extraction efficiency such as the IL volume, sample pH, extraction time, centrifugal time, dissoluble temperature and ionic strength were optimized. The extracts were analyzed by high-performance liquid chromatography (HPLC) coupled with diode array detector (DAD). Under the optimized conditions, recoveries (50.5–109.1%) were obtained for the target analytes in water samples. The calibration curves were linear and the correlation coefficient ranged from 0.9947 to 0.9973 in the concentration levels of 5–100 μg L^?1. The relative standard deviations (RSDs, n?=?5) were 6.80–10.78%. The limit of detections (LODs) for the five polar herbicides were between 0.46 μg L^?1 and 0.89 μg L^?1.     

Determination of trace amounts of nystatin in water and vaccine samples using sodium dodecyl sulfate-coated iron oxide magnetic nanoparticles followed by high-performance liquid chromatography–ultraviolet detection

In this work, magnetic solid-phase extraction based on sodium dodecyl sulfate-coated Fe₃O₄ nanoparticles has been successfully applied for extraction and preconcentration of trace amounts of nystatin from water and vaccine samples prior to high-performance liquid chromatography–ultraviolet detection. Various experimental parameters affecting extraction and recovery of the analyte, such as the amount of sodium dodecyl sulfate, pH of the sample solution, salt concentration, extraction time, sample volume and desorption conditions, were systematically studied and optimized. Under optimized conditions, nystatin was quantitatively extracted. Proper linear range with good coefficient of determination, (R ² > 0.99) and limit of detection and quantification (based on signal-to-noise ratios of 3 and 10) of 2.0 and 5.0 µg L^?1, over the investigated concentration range (5–700 µg L^?1), were obtained, respectively. The intra-day and inter-day relative standard deviations at 50 µg L^?1 level of NYS were 1.4 and 4.5% based on six replicate determinations. The accuracy of the method was evaluated by recovery measurements on spiked samples. Suitable recoveries of 96–102 and 26–44% were achieved (at spiked levels of 50, 300 and 500 µg L^?1) for water and vaccine samples, respectively.     

Application of DLLME Based on the Solidification of Floating Organic Droplets for the Determination of Dinitrobenzenes in Aqueous Samples

Dispersive liquid–liquid microextraction (DLLME) based on the solidification of floating organic droplets (DLLME-SFO) combined with gas chromatography-electron-capture detection (GC–ECD) has been developed for extraction and analysis of three dinitrobenzenes. The extraction conditions including extraction solvent, disperser solvent, extraction time, salt effect and temperature were investigated and optimized systematically. The limits of detection were 0.019 μg L^?1 for 1,4-dinitrobenzene, 0.079 μg L^?1 for 1,3-dinitrobenzene and 0.034 μg L^?1 for 1,2-dinitrobenzene. Moreover, it offered good repeatability and high recovery. This method was successfully applied to monitor DNBs in different water samples.     

Dispersive liquid–liquid microextraction based on ionic liquid in combination with high-performance liquid chromatography for the determination of bisphenol A in water

A method termed dispersive liquid–liquid microextraction (DLLME) coupled with high-performance liquid chromatography-variable wavelength detection (HPLC-VWD) was developed. DLLME-HPLC-VWD is a method for determination of bisphenol A (BPA) in water samples. In this microextraction method, several parameters such as extraction solvent volume, sample volume, disperser solvent, ionic strength, pH, and disperser volume were optimised with the aid of interactive orthogonal array and a mixed level experiment design. First, an orthogonal array design was used to screen the significant variables for the optimisation. Second, the significant factors were optimised by using a mixed level experiment. Under the optimised extraction conditions (extraction solvent: ionic liquid [C₆MIM][PF₆], 60 µL; dispersive solvent: methanol, 0.4 mL; and pH = 4.0), the performance of the established method was evaluated. The response linearity of the method was observed in a range of 0.002–1.0 mg L^?1 (three orders of magnitude) with correlation coefficient (R ²) of 0.9999. The repeatability of this method was 4.2–5.3% for three different BPA levels and the enrichment factors were above 180. The extraction recovery was about 50% for the three different concentrations with 3.4–6.4% of RSD. Limit of detection of the method was 0.40 µg L^?1 at a signal-to-noise ratio of 3. In addition, the relative recovery of sample of Songhua River, tap water and barrel-drain water at different spiked concentration levels was ranged 95.8–103.0%, 92.6–98.6% and 87.2–95.3%, respectively. Compared with other extraction technologies, there have been the following advantages of quick, easy operation, and time-saving for the present method.     

Preconcentration and determination of low amounts of cobalt in black tea,paprika and marjoram using dispersive liquid–liquid microextraction and flame atomic absorption spectrometry

A dispersive liquid–liquid microextraction (DLLME) method for separation/preconcentration of ultra trace amounts of Co(II) and its determination with FAAS was developed. The DLLME behavior of Co(II) using Aliquat 336-chloride as ion pairing agent was systematically investigated. The factors influencing the ion pair formation and extraction by DLLME method were optimized. Under the optimized conditions for 150 µL of extraction solvent (carbon tetrachloride), 1.5 mL disperser solvent (acetonitrile) and 5 mL of sample, the enrichment factor was 30. The detection limit was 5.6 µg L^?1 and the RSD for replicate measurements of 1 mg L^?1 was 1.32 %. The calibration graph using the preconcentration system for cobalt was linear from 40 to 400 µg L^?1 with a correlation coefficient of 0.999. The proposed method was successfully applied for determination of cobalt in black tea, paprika and marjoram real samples.     

Determination of Veterinary Pharmaceuticals in Production Wastewater by HPTLC-Videodensitometry

An SPE-HPTLC method for simultaneous identification and quantification of seven pharmaceuticals in production wastewater was optimized and validated. The studied compounds were enrofloxacine, oxytetracycline, trimethoprim, sulfamethazine, sulfadiazine, sulfaguanidine and penicillin G/procaine. The method involves solid-phase extraction on hydrophilic-lipophilic balance cartridges with methanol and HPTLC analysis of extracts on CN modified chromatographic plates followed by videodensitometry at 254 and 366 nm. Optimization of chromatographic separation was performed by systematic variation of the mobile phase composition using genetic algorithm approach and the optimum mobile phase composition for TLC separation was 0.05 M H₂C₂O₄:methanol = 0.81:0.19 (v/v). Linearity of the method was demonstrated in the ranges from 1.5 to 15.0 μg L⁻¹ for enrofloxacine, 100–500 μg L⁻¹ for oxytetracycline, 150–600 μg L⁻¹ for trimethoprim, 300–1100 μg L⁻¹ for sulfaguanidine and 100–400 μg L⁻¹ for sulfamethazine, sulfadiazine and penicillin G/procaine with coefficients of determination higher than 0.991. Mean recoveries ranged from 74.6 to 117.1% and 55.1 to 108.0% for wellspring water and production wastewater, respectively. Only sulfaguanidine showed lower results. The described method has been applied to the determination of pharmaceuticals in wastewater samples from pharmaceutical industry.     

Multivariate Analysis for the Classification Differentiation of Brazilian Sugarcane Spirits by Analysis of Organic and Inorganic Compounds

Abstract

Brazilian sugarcane spirits were analyzed to elucidate similarities and dissimilarities by principal component analysis. Nine aldehydes, six alcohols, and six metal cations were identified and quantified. Isobutanol (LD 202.9 µg L^?1), butiraldehyde (0.08–0.5 µg L^?1), ethanol (39–47% v/v), and copper (371–6068 µg L^?1) showed marked similarities, but the concentration levels of n-butanol (1.6–7.3 µg L^?1), sec-butanol (LD 89 µg L^?1), formaldehyde (0.1–0.74 µg L^?1), valeraldehyde (0.04–0.31 µg L^?1), iron (8.6–139.1 µg L^?1), and magnesium (LD 1149 µg L^?1) exhibited differences from samples.     

Application of Solid-Phase Extraction Coupled with Dispersive Liquid–Liquid Microextraction for the Determination of Benzaldehyde in Injectable Formulation Solutions

Solid-phase extraction followed by dispersive liquid–liquid microextraction (SPE-DLLME) technique has been developed as a new analytical approach for extracting, cleaning up and preconcentrating benzaldehyde, a toxic oxidation product of the widely used preservative and co-solvent benzyl alcohol, in injectable formulation solutions. SPE of benzaldehyde from samples was carried out using C₁₈ sorbent. After the elution of benzaldehyde from the sorbent by using acetonitrile, DLLME technique was performed on the obtained solution. Benzaldehyde was preconcentrated by using DLLME technique. Thus, 1.5 mL acetonitrile extract (disperser solvent) and 55.0 µL 1,2-dichloroethane (extraction solvent) were added to 5 mL ultra pure water and a DLLME technique was applied. Several variables that govern the proposed technique were studied and optimized. Under optimum conditions, the method detection limit (LOD) of benzaldehyde calculated as three times the signal-to-noise ratio (S/N) was 0.08 µg L^?1. The relative standard deviation (RSD) for four replicates was 5.8 %. The calibration graph was linear within the concentration range of 0.5–500 µg L^?1 for benzaldehyde. The proposed method has been successfully applied to the analysis of the benzaldehyde in injectable formulation solutions (diclofenac, vitamin B-complex and voltaren) and the relative recoveries were between 88 and 92 % and show that matrix has a negligible effect on the performance of the proposed method.     

Molecularly imprinted stir bar sorptive extraction coupled with high-performance liquid chromatography for trace analysis of naphthalene sulfonates in seawater

In this paper, a novel molecularly imprinted polymer coated stir bar has been used to selectively extract naphthalene sulfonates (NS_s) directly from seawater sample. 1-Naphthalene sulfonic acid (1-NS) was used as template molecule. The effects of different parameters were optimized on the extraction efficiency and the optimum conditions were established as: the absorption and desorption times were fixed, respectively, at 10 and 15 min, stirring speed was 700 rpm, pH was adjusted to 4.1, amount of NaCl was 1 mol L^?1 and extraction process was performed at a temperature of 50 °C. The linear ranges were 2–250 µg L^?1 for 3,6-NDS-1-OH (1-naphthol-3,6-disulfonic acid), 4–250 µg L^?1 for 2-NS (2-naphthalene sulfonate) and 3–250 µg L^?1 for 1-NS. The detection limits were within the range of 0.32–0.95 µg L^?1. Under optimum conditions, the detection limits of the NSs were 0.84, 0.95 and 0.32 µg L^?1 with the enrichment factor of 117-, 41- and 77-fold for 2-NS, 1-NS, and 6-NDS-1-OH, respectively. The repeatability of the method was satisfactory (0.53 ≤ RSD ≤6.0 %, n = 10). The method has been successfully applied for the analysis of trace amounts of three naphthalene sulfonates in seawater of Chabahar Bay.     

LC Determination of Trace Amounts of Phenoxyacetic Acid Herbicides in Water after Dispersive Liquid–Liquid Microextraction

Dispersive liquid–liquid microextraction (DLLME) for extraction and preconcentration of phenoxyacetic acid herbicides in water samples is described. After adjusting the pH to 1.5, the sample was extracted in the presence of 10% w/v sodium chloride by injecting 1 mL acetone as disperser solvent containing 25 μL of chlorobenzene as extraction solvent. The effect of parameters, such as the nature and amount of extraction and disperser solvents, ionic strength of the sample, pH, temperature and extraction time were optimized. DLLME was followed by LC for the determination of 2,4-dichlorophenoxyacetic acid and 4-chloro-2-methyl phenoxyacetic acid. The method had good linearity and a wide linear dynamic range (0.5–750 μg L^?1) with a detection limit of 0.16 μg L^?1 for both the PAAs, making it suitable for their determination in water samples.     

Ultrasound-assisted dispersive liquid–liquid microextraction and multivariate optimization for determination of Sodium Closantel in biological samples and pharmaceutical formula

A fast and simple ultrasound-assisted dispersive liquid–liquid microextraction method for determination of Sodium Closantel has been developed. High-performance liquid chromatography with ultraviolet detector has been used for the determination of Sodium Closantel. The effect of influencing parameters such as type and volume of extraction and disperser solvents, pH of sample solution, extraction time and amount of salt was also investigated. Optimization of method was performed using Plackett–Burman experimental design and surface response methodology. Under the optimal conditions, the linear dynamic range of Sodium Closantel was from 10 to 3000 µg L^?1 with a correlation coefficient of 0.997 and a detection limit of 1.0 µg L^?1. The relative standard deviation was less than 3.5% (n = 5). The method has been successfully applied for determination of Sodium Closantel in real samples. The enrichment factor was 48 under optimal conditions.     

Dispersive Liquid–Liquid Microextraction of Silver Prior to Determination by Microsample Introduction-Flame Atomic Absorption Spectrometry

Abstract

A new simple and sensitive method has been proposed for rapid determination of trace levels of silver in environmental water samples, using dispersive liquid–liquid microextraction (DLLME) prior to its microsample introduction-flame atomic absorption spectrometry. Under the optimum conditions, the linear range was 0.1–7 µg L^?1 and limit of detection was 0.018 µg L^?1. The relative standard deviation for 0.50 and 5.00 µg L^?1 of silver in water sample was 4.0 and 1.7%, respectively. The relative recoveries of silver from tap, well, river, and seawater samples at spiking levels of 1.00 and 5.00 µg L^?1 were in the range of 86.4–98.6%.     

Use of ionic liquid based chitosan as sorbent for preconcentration of fluoroquinolones in milk,egg, fish,bovine, and chicken meat samples by solid phase extraction prior to HPLC determination

The possibility of using ionic liquid based chitosan sorbent for the separation and preconcentration of fluoroquinolone antibiotics (marbofloxacin, enoxacin, ofloxacin, ciprofloxacin, and enrofloxacin) has been studied. For this reason, different ionic liquids were prepared and coated on the chitosan sorbent. The conditions of the preconcentration of fluoroquinolones on a microcolumn have been optimized and the extraction efficiencies of the prepared sorbents have been compared. The compounds were eluted with 5 mL of 20% NH₃ (v/v, MeOH) solution and determined by HPLC with diode array and fluorescence detector. The limits of detection were found as 4.23 µ g L^?1 for marbofloxacin, and 1.09 µg L^?1 for enoxacin; 3.23 × 10^?3 µg L^?1 for ofloxacin; 8.39 × 10^?3 µg L^?1 for ciprofloxacin; and 19.50 × 10^?3 µg L^?1 for enrofloxacin. The developed method was applied for the analysis of fluoroquinolone in milk, egg, fish, bovine, and chicken samples and the recoveries were obtained in the range 70–100%.     

Determination of Mycotoxins Using Hollow Fiber Dispersive Liquid–Liquid–Microextraction (HF-DLLME) Prior to High-Performance Liquid Chromatography – Tandem Mass Spectrometry (HPLC - MS/MS)

A modified hollow-fiber-supported dispersive liquid-liquid microextraction (HF-DLLME) method was developed for the determination of aflatoxins and ochratoxin A in food samples. The various parameters affecting the efficiency of extraction, such as pH, salt addition, extraction time, stirring rate, desorption time, type and volume of extractant and disperser solvents were carefully studied and optimized using two step strategies. The linearity of the evaluated results was 0.1 to 30?μg L^?1 for aflatoxins and 0.1 to 20?μg L^?1 for ochratoxin A, with regression coefficients (R²) exceeding 0.9990. The precision was satisfactory with relative standard deviation values less than 11%. The method accuracy was within the recommended range from 70% to 120% and analyte accuracy between 83% and 101%. The limits of detection and quantification were in the range from 0.04 to 0.06?μg L^?1 and 0.08 to 0.13?μg L^?1, respectively, for multi-aflatoxins, and 0.02 to 0.04?µg L^?1 and 0.08 to 0.10?µg L^?1, respectively, for ochratoxin A. The developed method was successfully applied for the determination of mycotoxins in food samples.     

Magnetic Stirring-Assisted Dispersive Suspended Microextraction with Solidification of a Floating Organic Droplet for the Determination of Trace Fungicides in Water and Wine

For the first time, a simple method for magnetic stirring-assisted dispersive suspended microextraction has been developed for the determination of three fungicides (azoxystrobin, diethofencarb, and pyrimethanil) in water and wine samples. The method is based on the solidification of a floating organic droplet coupled with high performance liquid chromatography. In the proposed method, the low toxicity solvent 1-dodecanol was used as the extractant. Both the extraction and phase separation process were performed with magnetic stirring. No centrifugation step was involved. After separating the two phases, the extraction solvent droplet was easily collected through solidification at lower temperature. Important parameters such as the kind and volume of organic extraction solvent, extraction and restoration speed, extraction and restoration time, and salt concentration were optimized. Under the optimal conditions, the limits of detection for the analytes varied from 0.14 to 0.26 µg L^?1. The enrichment factors ranged from 125–200. The linearity ranges were 1–2000 µg L^?1, yielding correlation coefficients (r) higher than 0.9990. The relative standard deviation (n = 6) at two spiked level of 0.2 µg mL^?1 and 4 µg L^?1 varied between 2.2% and 7.8%. Finally, the developed technique was successfully applied to determine target fungicides in real water and wine samples, where the obtained recoveries ranged from 83.8–105.3%     

Magnetic Solid-Phase Extraction and Ionic Liquid Dispersive Liquid–Liquid Microextraction Coupled with High-Performance Liquid Chromatography for the Determination of Hexachlorophene in Cosmetics

An efficient, simple, and fast method based on ionic liquid dispersive liquid–liquid microextraction (IL-DLLME) followed by magnetic solid-phase extraction (MSPE) was developed as a new technique for extracting and purifying hexachlorophene (HCP) in cosmetics prior to high-performance liquid chromatography (HPLC) determination. In this method based on IL-DLLME and MSPE, 1-hexyl-3-methylimidazolium hexafluorophosphate ([C₆MIM][PF₆]) is used as the extraction solvent and Fe₃O₄ nanoparticles are used to remove hydrophobic additives in the cosmetics by physical adsorption. The main parameters affecting the efficiency of the IL-DLLME and MSPE of HCP were investigated and optimized. Under the optimum conditions, the method was linear in the range 0.5–40 µg mL^?1 with a correlation coefficient (R ²) of 0.9976 and had a detection limit of 0.14 µg mL^?1 at a signal-to-noise ratio (S/N) of 3. The recoveries of HCP in three cosmetic samples using the proposed method were in the range 74.5–97.7%, and the relative standard deviations (RSD, n = 5) were in the range 3.8–6.7%. The developed method was successfully applied to the determination of HCP in cosmetics.     

Dispersive Liquid–Liquid Microextraction for the Preconcentration of Multiple Classes of Pesticides in Water

A simple, rapid, efficient, and environmentally friendly method was developed for the preconcentration of atrazine, simazine, diuron, bentazone, tebuconazole, and fipronil from water. Dispersive liquid–liquid microextraction was employed with determination by liquid chromatography–tandem mass spectrometry. The volumes of extraction and disperser solvents, the concentration of sodium chloride, and the pH were optimized by response surface methodology. The optimum conditions involved the use of 150 µL of 1:1 (v/v) monochlorobenzene:dichlorobenzene as the extraction solvent, 2 mL acetonitrile as the disperser solvent, and 10 mL of sample at pH 3.0. The accuracy was evaluated in terms of recovery values that were from 54 to 112%. The relative standard deviations ranged from 4 to 27%. The limits of quantification were between 0.005 and 0.05 µg L^?1. The optimized method had low matrix effects for the analytes and the results demonstrated application for the determination of pesticides in water.     

The separation–preconcentration and determination of ultra-trace gold in water and solid samples by dispersive liquid–liquid microextraction using 4-ethyl-1(2-(4-(4-nitrophenyl)piperazin-1-yl)acetyl)thiosemicarbazide) as chelating agent and flame atomic absorption spectrometry

A selective separation and preconcentration method for the determination of gold ions in water and ore samples has been developed using dispersive liquid–liquid microextraction, followed by flame atomic absorption spectrometry. 4-Ethyl-1(2-(4-(4-nitrophenyl)piperazin-1-yl)acetyl)thiosemicarbazide) (NPPTSC) has been used for the first time as new chelating reagent. A mixture of ethanol (dispersive solvent) and carbon tetrachloride (extraction solvent) was used. Some parameters affecting the extraction procedure including the type and volume of the extracting and dispersive solvents, HNO₃ concentration, the chelating agent amount, volume of sample, and foreign ions have optimized. Also, the complex formation between gold ions and the ligand has been investigated in a methanol–water solution (1:1) using UV–visible spectrometry. The spectrophotometric titration data showed that of Au–NPPTSC complex composition was found to be 3:2. After optimizing the instrumental and experimental parameters, we achieved a detection limit of 1.5 µg L^?1, a preconcentration factor of 50, and a linear dynamic range of 10.0–400.0 µg L^?1. The relative standard deviation obtained 2.1% at 50 µg L^?1 for gold ions (n = 10). The proposed method was successfully performed for the determination of gold in certified reference material, environmental water, and ore samples.     

Ionic liquid-based dispersive liquid–liquid microextraction for the separation and preconcentration of lead in water samples prior to FAAS determination without chelating agent

In the present study, an environment-friendly sample preparation method termed ionic liquid-based dispersive liquid–liquid microextraction combined with flame atomic absorption spectrometry has been developed for the determination of Pb(II) ion in water samples prior to flame atomic absorption spectrometry determination. In this method, ionic liquid was used as an extraction solvent instead of the organic solvent used in the conventional dispersive liquid–liquid microextraction (DLLME) assay, and there is no need for a chelating agent. Several variables that may affect extraction efficiencies, including pH, the volume of ionic liquid, the type and volume of disperser solvent, salt addition, and the time for centrifugation and extraction were studied and optimised. Under the optimised conditions, the calibration curve exhibited linearity over the range of 20.0–1000.0 μg L^?1. The enrichment factor and the limit of detection based on 3S_b/m were 35.0 and 5.9 μg L^?1, respectively. Seven replicate determination of a solution containing of 100.0 μg L^?1 Pb(II) ions gave a relative standard deviation of ±2.1%. Finally, the feasibility of the proposed method for Pb(II) determination was assessed by the analysis of certi?ed reference material and various water samples and the satisfactory results were obtained.     

Square-Wave Anodic Stripping Voltammetry (SWASV) for the Determination of Ecotoxic Metals,Using a Bismuth-Film Electrode

This article reviews the use of square wave anodic stripping voltammetry for the simultaneous determination of ecotoxic metals (Pb, Cd, Cu, and Zn) on a bismuth-film (BiFE) electrode. The BiFE was prepared in situ on a glassy-carbon electrode (GCE) from the 0.1 mol L^?1 acetate buffer solution (pH 4.5) containing 200 µg L^?1 of bismuth (III). The addition of hydrogen peroxide to the electroanalytical cell proved beneficial for the interference-free determination of Cu (II) together with zinc, lead, and cadmium, using the BiFE. The experimental variables were investigated and optimized with the view to apply this type of voltammetric sensor to real samples containing traces of these metals. The performance characteristics, such as reproducibility, decision limit (CC_a), detection capability (CC_β), sensitivity, and accuracy indicated that the method holds promise for trace Cu²⁺, Pb²⁺, Cd²⁺, and Zn²⁺ levels by employment of Hg-free GCE with SWASV. CCa, and CCβ were calculated according to the Commission Decision of 12 August 2002 (2002/657/EC). Linearity was observed in the range 20–280 µg L^?1 for zinc, 10–100 µg L^?1 for lead, 10–80 µg L^?1 for copper, and 5–50 µg L^?1 for cadmium. Using the optimized conditions, the stripping performance of the BiFE was characterized by low limits of detection (LOD). Finally, the method was successfully applied in real as well as in certified reference water samples.