Coprecipitation of Amino Acids with Mixed Hydroxide of Iron(III) and Copper(II)

Abstract

A coprecipitation method for concentrating amino acids from aquatic environments with a mixed hydroxide of iron(III) and copper(II) was developed. The percent coprecipitation of glycine, alanine, glutamic acid, aspartic acid, and lysine, being independent of pH in the range of 8.5 to 9.5, was more than 95%.     

Reversed Phase Extraction Chromatographic Separation of Manganese(II) with Tributyl Phosphate

Abstract

The extraction chromatography of manganese(II) was developed using tributyl phosphate as extractant from thiocyanate media with silica gel as the stationary phase. Manganese was extracted from 1.5 M ammonium thiocyanate, stripped with mineral acids and determined spectrophotometrically at 450 nm. It was separated from alkali metals, Mo(VI), nickel, silver and lead by selective extraction, and from iron(III), zinc, cobalt by selective stripping. The method was extended for the analysis of manganese in samples of soil and minerals.     

Indirect Simultaneous Kinetic Determination of L‐Cysteine and Homocysteine by ANNs

Abstract

Simultaneous determination of cysteine and homocysteine in binary mixtures was performed by application of neural networks on the spectral kinetic data. This method is based on the complexation of bivalent iron with 2,2′–bipyridin (bipy). Iron(III) is quantitatively reduced to iron(II) with cysteine and homocysteine in the presence of 2,2′–bipyridin producing iron(II)–bipy complex (λmax=522 nm), and it can be used as a visible spectrophotometric signal for indirect simultaneous determination of the cysteine and homocysteine concentrations. On the basis of the difference in the rate between the two reactions, these two amino acids can be determined simultaneously using principal component‐artificial neural networks (PC‐ANN). The parameters controlling behavior of the system were investigated and optimum conditions selected. Determinations were made over the concentration range 0.10–5.50 µg · mL^?1 of cysteine and 0.1–5.00 µg · mL^?1 of homocysteine. Applying this method satisfactorily to simultaneous determination of these amino acids with total relative standard error less than 5% validated the proposed method.     

Coupled Redox and pH Potentiometric Responses of Electrodes Coated with Polypyrrole

ABSTRACT

The coupled influence of solution acidity and redox electrolytes on the open-circuit potentials of polypyrrole-modified electrodes was studied by recording the potential vs. time dependencies. It was observed that doping anions affect the relative rate of the responses resulting from pH influence (pH response) and from the presence of a redox couple in the solution, such as Fe(III)/Fe(II) or Fe(CN)6^3-/4-(redox response). Separation of the pH and redox responses was possible for polypyrrole doped with large organic anions of weak acids (Tiron, sulphosalicylic acid, Indigo Carmine). In such cases, a very fast pH response was recorded after which the polymer potential relaxed to the solution redox potential in each case. The final stable potential was determined entirely by the potential of the redox couple in solution. The final potential was pH-independent unless the redox potential was influenced by solution acidity. The solution pH determines only the shape of the potential vs. the time dependence, e.g. much faster responses were observed for solutions with a higher H* concentration.     

Electrochemical characterization of Prussian blue type nickel hexacyanoferrate redox mediator for potential application as charge relay in dye-sensitized solar cells

A polynuclear electronically/ionically (redox) conducting mixed-valent inorganic material such as nickel(II) hexacyanoferrate(II,III), NiHCF, was considered for potential application as a redox mediator (charge relay) in dye-sensitized solar cell (DSSC). The NiHCF redox reactions were found fast and reversible not only when the system was studied as thin film exposed to an aqueous supporting electrolyte but also as bulk material (pasted powder) in solid state, i.e., in the absence of contact with external liquid electrolyte phase. Usefulness of NiHCF material was diagnosed using conventional electroanalytical approaches, solid-state voltammetric methodology, as well as the dynamic electrochemical impedance spectroscopy technique that permitted monitoring of impedance spectra under potentiodynamic conditions. The material was utilized in a mixed-valent state, i.e., as a mixture of K₄Ni^II[Fe^II(CN)₆] and K₃Ni^II[Fe^III(CN)₆] in which iron(II) and iron(III) sites were at the 1:1 ratio. Under such conditions, dynamics of electron-hopping between mixed-valent iron sites was maximized. Our DSSC utilized cis–dithiocyanoatobis(4,4′-dicarboxylic acid-2,2′-bipyridine) ruthenium(II) dye (N3) adsorbed onto TiO₂ semiconductor and NiHCF as redox mediator. Although performance of our DSSC was not optimized in terms of the NiHCF film thickness and morphology, as well as lower photocurrents in comparison to those characteristic of the iodine/iodide based DSSC were obtained, our system yielded readily fairly high open-circuit photovoltages on the level of 800 mV. An important issue was that the formal potential of NiHCF was more positive relative to the potential of the iodide/triiodide couple while being still more negative than that equivalent to the ground state of the N3 dye. Thus, NiHCF mediator was able to regenerate the dye.

     

Determination of Molybdenum(VI) At Trace Levels by a Catalytic Polarographic Method

Abstract

ARSTRACT

A d.c. polarography method for molybdenum (VI) determination at trace levels has been developed. The reaction is catalytic between molybdenum, salicylaldoxime (SCAD) and bromate in acetic-acetate medium. The obtained peak is proportional to molybdenum (VI) concentrations in the range 1.08.10^?a to 1.37.10^?6 M. The proposed procedure is selective, the most serious interferents being W(VI), Pb(II) and Fe(II). It is applied to molybdenum determination in steel samples after iron extraction by ethyl ether.     

Separation of Tron(Iii) By Extraction Chromatography With Aliquat 3365 From Citrate Solution

Abstract

A rapid method is proposed for separation of iron(III) with Aliquat 336S as the stationary phase coated on silica gel column with citric acid buffered at pH 4,5 as mobile phase. the extracted iron is stripped from the column with different mineral acids and determined spectrophotracally as its complex with 1,10-phenanthroline, Iron was separated from chromium, molybdenum, titanium and nickel which are generally associated in steel samples. Similar separations of iron from lead, zinc, cadmium, bismuth and cobalt have significance in environmental sample analysis. the method is extended for analysis of iron from samples of sediment and sea-water.     

Principal Component‐Wavelet Neural Network as a Multivariate Calibration Method for Simultaneous Determination of Iron,Nickel, and Cobalt

Abstract

Principal component‐artificial neural network (PC‐ANN) and principal component‐wavelet neural network (PC‐WNN) are applied for simultaneous determination of iron(II), nickel(II), and cobalt(II). A simple and selective spectrophotometric method for simultaneous determination of iron(II), nickel(II), and cobalt(II) based on formation of their complexes with 1‐(2‐pyridylazo)‐2‐naphtol (PAN) in micellar media is described. Although the complexes of Fe(II), Ni(II), and Co(II) with reagent show a spectral overlap, they have been simultaneously determined by PC‐ANN and PC‐WNN. The results obtained by the two methods were compared and it was shown that in PC‐WNN, the convergence speed was faster and the root mean square error of prediction set was also smaller than PC‐ANN. Interference effects of common anions and cations were studied and the proposed method was also applied satisfactorily to the determination of Fe(II), Ni(II) and Co(II) in synthetic samples.     

Electrothermal Atomic Absorption Spectrometric Determination of Cobalt,Copper and Nickel in Fresh Water After Their Preconcentration by Precipitate Flotation

Abstract

A method is developed for simultaneous separation and determination of μg/L levels of Co(II), Cu(II) and Ni(II) in fresh water by precipitate flotation. The optimal conditions of the experimental procedure with hydrated iron(III) oxide and iron(III) tetramethylenedithiocarbamate as collectors were investigated. The pH interval of the working medium, within which Co(II), Cu(II) and Ni(II) can be successfully separated, was determined from the aspect of collectors and surfactant stability. The amounts of the elements investigated were determined by electrothermal atomic absorption spectrometry. The detection limit of the method is 0.15 μg/L for cobalt, 0.03 μg/L for copper and 0.79 μg/L for nickel.     

Spectrophotometric Determination of Copper(II) as the Azide Complexes,in the Presence of Iron(III) Cations

Abstract

A method for the spectrophotometrio determination of copper(II), in the presence of iron(III) cations (excess), was stablished. The masking of iron is made with sodium fluoride salt in 50 % (v/v) water/acetone medium. In the recommended conditions, absorbances for cupric complexes are measured at 435 nm where molar absorptivity is 6.00 × 10³ 1 mol^?1 cm^?1.

The stable ayetern obeys Beer's law and is suitable for the copper determination in concentration range from 2.0 to 9.0 mg 1^?l. The iron(III) ion interference (until ca. 600 mg 1^?l) can be completely suppressed. The influence of diverse ions and several others factore were studied.

The results show that copper(II) can be accurately determined by azide apectrophotometric method, if the samples were suitablely treated by the recommended procedure.     

Complexation Properties of Typical Soil and Peat Humic Acids with Copper(II) and Cadmium(II)

Abstract

Potentiometric titration with ion-selective electrodes was applied to determine characteristic parameters like the degree of complexation and the approximate molecular weight of humic acids from theoretical considerations and conditional stability constants for the complexes of Cu(II) and Cd(II) with humic acids obtained from sources such as garden soil, peat prepared by decomposing water hyacinth in soil and humified water hyacinth. Double-reciprocal and Scatchard plots were constructed to determine the conditional stability constants of the complexes formed. Cu(II) was found to have more affinity for the humic acids than Cd(II) and the stability of the metal complexes in aqueous medium was found to increase with increasing pH. The order of stability of the complexes was M-HA (soil)>M-HA (peat)>M-HA (humified water hyacinth), where M and HA represent metal and humic acids, respectively.     

Indirect Spectrophotometric Determination of Vanadium(IV) by Flow Injection Analysis Based on the Redox Reaction with Copper(II) in the Presence of Neocuproine

Abstract

An indirect photometric method with a continuous-flow analysis is presented for the determination of trace amounts of vanadium(IV). It is based on the redox reaction of copper(II) with vanadium(1V) in the presence of neocuproine. In the presence of neocuproine, copper(I1) is reduced easily by vanadium(I V) to a copper(1)-neocuproine complex, which shows a n absorption maximum at 454 nm. By measuring t h e absorbance of the complex at this wavelength, vanadium(1V) in t h e range 2×10^?6 - 8 × mol dm^?5 mol dm^?3 can be determined at a rate of 120 samples h^?1. The fractional determination of vanadium(1V) and iron(I1) is also studied.     

Determination of Iron (II) in Water by a Spectrophotometric Method After Preconcentration on an Organic Solvent-Soluble Membrane Filter

Abstract

A solvent-soluble membrane filter is proposed for a simple and rapid preconcentration and spectrophotometric determination of iron (II), which was collected on a nitrocellulose membrane filter as an ion-associate of the cationic complex of iron (II)-1,10-phenanthroline with an anionic surfactant of dodecyl sulfate. The ion-associate collected was dissolved in 5 ml of 2-methoxyethanol together with the filter. The color intensity due to the ion-associate in the resulting solution was measured at 510 nm against a reagent blank. Beer's law is obeyed in the range 1–15 μg Fe (II) in 5 ml of solvent with excellent reproducibility, and detection limits better than 0.5 μg dm^?3 as Fe (II) can be achieved. The diverse components normally present in water do not interfere when proper masking reagent is added. The proposed method has been applied to the analysis of water samples from several sources such as river water, ground water and tapwater samples, the recoveries of the iron (II) added to the samples are quantitative, and results found are satisfactory.     

CHARACTERIZATION OF DINUCLEAR DIALKOXOBRIDGED IRON(III)-L-PROLINE COMPLEXES AS THE REARRANGEMENT PRODUCTS OF TRINUCLEAR OXOBRIDGED IRON(III)-L-PROLINE COMPLEXES

Abstract

Dinuclear dimethoxolized iron(III)-L-proline complexes, obtained as a result of thermal, photolytic, and chemoreductive rearrangement of trinuclear oxobridged iron(III)-L-proline complexes, have been characterized by spectral and magnetic measurements. Under the conditions described, the rearrangement does not occur in other solvents nor when parallel complexes with other L-amino acids are used, including, surprisingly, L-hydroxyproline.     

Continuous-Flow Determination of Phenol With Chemically Immobilized Polyphenol Oxidase (Tyrosinase)

Abstract

The use of covalently bound mushroom polyphenol oxidase (tyrosinase, EC 1.10.3.1) for the determination of μg/mL and ng/mL concentrations of phenol in water samples with use of continuous-flow sample/reagent processing is described. Immobilization on controlled-pore glass, CPG, was accomplished via diazo coupling. Detection was effected with hexacyanoferrate(II) as a redox mediator and was either spectrophotometric or amperometric. the immobilized enzyme preparation was part of an open tubular reactor (CPG thermally embedded on Tygon tubing). the redox mediator was used either in solution or as part of a thin-layer cell and immobilized on poly(4-vinylpyridine) incorporated in a carbon paste electrode. Different spectrophotometric and amperometric strategies are compared and the method is applied to the determination of phenol in water samples and quality control standards.     

Construction of a New Perbromate-Selective Electrode. Kinetic Study of the Iron(II)- Perbromate Reaction and Microdetermination of Iron

Abstract

A perbromate- selective membrane electrode with a liquid membrane of crystal violet-perbromate dissolved in chlorobenzene is described, The liquid membrane electrode exhibits rapid and near Nernstian response to perbromate activity from 10^?5 to 10^?2 M. The response is unaffected by pH in the range 2–10, Major interferences are periodate and perchlorate. A kinetic study of the iron(II)- perbromate reaction was carried out with the perbromate electrode, A potentiometric method is described for the determination of 50–500 μg of iron (II) with relative errors and standard deviations of 1–2%.     

Coordination Studies of Iron(II) Protoporphyrin IX and Iron(II) Hematoporphyrin IX with 4,4′-Dipyridyl and other Nitrogenous Bases

Abstract

The results of spectral studies of iron(II) protopor-phyrin IX and iron(II) hematoporphyrin IX with several substituted pyridines are reported. The existence in solution of an iron(II) porphyrin complex coordinated to a water molecule and to a substituted pyridine was shown by isolation of the complex from solution. The complex isolated was dimeric inono-4,4′-dipyridyl diaquo iron(II) hematoporphyrin. Addition of ethanol to the aqueous solvent inhibits coordination of iron(II) porphyrins with substituted pyridines. The protoporphyrin ring enhances coordination relative to the hematoporphyrin ring.     

Cyclic Voltammetric Study of the R-Nitroso Salt Application to the Indirect Determination of Iron(II)

Abstract

The electrochemical behaviour of the R-nitroso salt in 0.5 M HAc/NaAc at pH 4.7 is studied by cyclic voltammetry. The compound shows a very sharp reduction peak at -0.37 V vs SCE giving the corresponding amine derivative. The height of the peak is shown to be inversely proportional to the iron (II) concentration of the solution. A linear calibration plot is obtained between 0 and 56 ppm of iron (II) using, initially, 4.0 mM solution of the salt. A simple and fast procedure was developed for the analysis of standard samples of ferrous iron.     

Speciation of Charged Complexes by Donnan Dialysis

Abstract

The assignment of metal complexes to various regimes on the basis of their dissociation kinetics is one type of metal speciation study. The most common scheme, which involves column ion-exchange as a means of separating free metal ions and metals in the form of highly labile complexes from other forms of metals in the sample, is demonstrated to categorize incorrectly stable, charged complexes such as iron(II) and nickel(II) o-phenanthroline as labile. Donnan dialysis is an alternative ion-exchange method for metal speciation studies. Data are provided which demonstrate that the above complexes are correctly assigned by the Donnan dialysis method. The relative labilities of ethylenediamine and triethylenetetramine complexes of iron (II) and nickel (II) are also correctly determined by Donnan dialysis.