Assessing effects of pH,metal ion and natural organic matter on identification and determination of reduced glutathione by cathodic stripping voltammetry

The effects of pH, metal ions (i.e. Cu²⁺, Cd²⁺, Pb²⁺ and Zn²⁺) and natural organic matter (i.e. Suwannee River natural organic matter standard [SRNOM]) on determination of thiol (i.e. reduced glutathione [GSH]) by cathodic stripping voltammetry were evaluated. pH was the most critical parameter to influence GSH voltammogram (i.e. peak shape, position and height). In presence of Cu and Cd, secondary peaks were found at [metal]/GSH > 1 due to formation of GSH complexes at pH = 8.0 (Cu and Cd) and 2.5 (Cu only). On the other hand, Pb showed negligible influence on GSH voltammogram at pH 8.0 and 2.5 within [Pb]/[GSH] = 0.01–2.0. Zn significantly reduced GSH peak height at pH 2.5 at [Zn]/[GSH] = 0.01–2.0. SRNOM peak significantly overlapped with GSH peak at pH 8.0 and [SRNOM] > 1 mg L^?1 but was clearly separated from the GSH peak at pH 2.5. However, at pH 2.5, the presence of metal ions and/or SRNOM significantly underestimated GSH concentration (recovery = 21–69%), likely due to metal complexation with GSH and/or SRNOM adsorption onto Hg electrode. The effects of metal ions were minimised by the addition of EDTA. The interference induced by SRNOM adsorption was reduced as the [SRNOM] was reduced to 1 mg L^?1 and the recovery was improved to 98%.     

Characterization of a Marine Microbial Community Used for Enhanced Sulfate Reduction and Copper Precipitation in a Two-Step Process

Marine microorganisms that are obtained from hydrothermal vent sediments present a great metabolic potential for applications in environmental biotechnology. However, the work done regarding their applications in engineered systems is still scarce. Hence, in this work, the sulfate reduction process carried out by a marine microbial community in an upflow anaerobic sludge blanket (UASB) reactor was investigated for 190 days under sequential batch mode. The effects of 1000 to 5500 mg L^?1 of SO₄ ^?2 and the chemical oxygen demand (COD)/SO₄ ^?2 ratio were studied along with a kinetic characterization with lactate as the electron donor. Also, the feasibility of using the sulfide produced in the UASB for copper precipitation in a second column was studied under continuous mode. The system presented here is an alternative to sulfidogenesis, particularly when it is necessary to avoid toxicity to sulfide and competition with methanogens. The bioreactor performed better with relatively low concentrations of sulfate (up to 1100 mg L^?1) and COD/SO₄ ^?2 ratios between 1.4 and 3.6. Under the continuous regime, the biogenic sulfide was sufficient to precipitate copper at a removal rate of 234 mg L^?1 day^?1. Finally, the identification of the microorganisms in the sludge was carried out; some genera of microorganisms identified were Desulfitobacterium and Clostridium.     

Fast Determination of Phenolic Compounds in Brazilian Wines from Vale do São Francisco Region by CE

Six phenolic compounds were separated and determined by capillary zone electrophoresis in red wine from Brazil’s region Vale do São Francisco with total analysis time of 12 min. The limit of detections varied from 1.59 to 2.24 mg L^?1. The relative standard deviations (for n = 6) varied from 0.28 to 3.50 %. The red wine samples analyzed were bought in the local market and the phenolic compound recoveries were in the range of 98–101 %. The concentrations of gallic acid in the samples of wines varied from 16.0 to 42.0 mg L^?1, caffeic acid (3.16–5.18 mg L^?1), syringic acid (5.73–13.0 mg L^?1), kaempferol (2.32–4.33 mg L^?1), quercetin (1.68–4.03 mg L^?1), myricetin (7.52–25.1 mg L^?1). The concentrations found agree with data reported in the literature.     

Biomethane Production in an AnSBBR Treating Wastewater from Biohydrogen Process

An anaerobic sequencing batch reactor containing immobilized biomass (AnSBBR) was used to produce biomethane by treating the effluent from another AnSBBR used to produce biohydrogen from glucose- (AR-EPHG) and sucrose-based (AR-EPHS) wastewater. In addition, biomethane was also produced from sucrose-based synthetic wastewater (AR-S) in a single AnSBBR to compare the performance of biomethane production in two steps (acidogenic and methanogenic) in relation to a one-step operation. The system was operated at 30 °C and at a fixed stirring rate of 300 rpm. For AR-EPHS treatment, concentrations were 1,000, 2,000, 3,000, and 4,000 mg chemical oxygen demand?(COD)?L^?1 and cycle lengths were 6 and 8 h. The applied volumetric organic loads were 2.15, 4.74, 5.44, and 8.22 g COD L^?1 day^?1. For AR-EPHG treatment, concentration of 4,000 mg COD L^?1 and 4-h cycle length (7.21 g COD L^?1 day^?1) were used. For AR-S treatment, concentration was 4,000 mg COD L^?1 day^?1 and cycle lengths were 8 (7.04 g COD L^?1 day^?1) and 12 h (4.76 g COD L^?1 day^?1). The condition of 8.22 g COD L^?1 day^?1 (AR-EPHS) showed the best performance with respect to the following parameters: applied volumetric organic load of 7.56 g COD L^?1 day^?1, yield between produced methane and removed organic material of 0.016 mol CH₄?g COD^?1, CH₄ content in the produced biogas of 85 %, and molar methane productivity of 127.9 mol CH₄?m^?3 day^?1. In addition, a kinetic study of the process confirmed the trend that, depending on the biodegradability characteristics of the wastewaters used, the two-step treatment (acidogenic for biohydrogen production and methanogenic for biomethane production) has potential advantages over the single-step process.     

Temperature-assisted ionic liquid-based dispersive liquid–liquid microextraction with following back-extraction for HPLC/UV–Vis determination of 3-indole acetic acid in pea plants

In this work, the ionic liquid (IL)[C₆mim][PF₆] was used as IL-based extractant for dispersive liquid–liquid microextraction, followed by back-extraction and HPLC/UV–Vis determination of 3-indole acetic acid (IAA) in pea plant. The effects of some crucial factors such as chemical structure and volume of IL, pH adjustment, dissolution temperature, extraction time, centrifugation time, and ionic strength of aqueous sample were studied. The linear range of the HPLC method for IAA quantification was 17.5 × 10^?2–36.8 mg L^?1. LOD, LOQ, method recovery, and preconcentration factor values were 0.170 mg L^?1, 0.175 mg L^?1, 98.3, and 40 %, respectively. The RSD for the suggested method was calculated as 0.93 % at 35.04 mg L^?1 of IAA and each IL phase was able to be reused for at least four DLLME/back-extraction cycles. To evaluate the applicability of the suggested method, IAA was determined in pea plant samples.     

Production of Ultra-high Molecular Weight Poly-γ-Glutamic Acid with Bacillus licheniformis P-104 and Characterization of its Flocculation Properties

A novel strain of Bacillus licheniformis P-104 was isolated from Chinese soybean paste to produce a bioflocculant. The bioflocculant was confirmed as ultra-high molecular weight poly-γ-glutamic acid (γ-PGA) using Fourier transform infrared spectrum, high-performance liquid chromatography, and gel permeation chromatography with multi-angle laser light scattering. The production technology and flocculation properties of γ-PGA were investigated. By fed-batch fermentation in a 7-L bioreactor, the maximum γ-PGA yield reached 41.6 g L^?1 with a productivity rate of 1.07 g L^?1 h^?1. The flocculating activity of γ-PGA for kaolin suspension was 33.5?±?1.6 1/OD under the optimized flocculation conditions (6 mM Ca²⁺, 1.5 mg L^?1 γ-PGA, and pH 6.0). The optimized dosage of γ-PGA for flocculation was just about 30 % of that of reported γ-PGA produced by other strains. Moreover, the flocculation activity of γ-PGA produced by strain P-104 was much higher than commercial γ-PGA with the molecular weight ranging 200–500 kDa and 1,500–2,500 kDa. This study provided a promising strain and an efficient method for production of ultra-high molecular weight γ-PGA which could be used as a potential green bioflocculant.     

A Simple Method for Determination of Homologue Imidazolium Cations in Ionic Liquids Using IC with Direct Conductivity Detection

An investigation was carried out into the fast determination of five homologue imidazolium cations in ionic liquids by ion chromatography using a cation-exchange column and direct conductivity detection. Ethylenediamine, complex organic acid (citric acid, oxalic acid and tartaric acid) and organic modifiers (acetonitrile) were used as mobile phase. The influences of the eluent types, eluent concentration, eluent pH and column temperature on separation of the cations were discussed. Simultaneous separation and determination of the five homologue imidazolium cations in ionic liquids were achieved under an optimum condition. The optimized mobile phase was consisted of 0.25 mmol L^?1 ethylenediamine + 0.5 mmol L^?1 citric acid + 3% acetonitrile (v/v) (pH 4.1), set at a flow rate of 1.0 mL min^?1. The column temperature was 40 °C and detection limits were obtained in the range of 1.1–45.6 mg L^?1. The relative standard deviations of the chromatographic peak areas for the cations were <3.0% (n = 5). This method was successfully applied to separate imidazolium cations in ionic liquids produced by organic synthesis. The recoveries of spiked components were 92.5–101.9%.     

Liquid–liquid microextraction and spectrophotometric determination of anionic surfactants using Astra Phloxine FF

A novel and simple procedure for determination of anionic surfactants has been developed. The method is based on the reaction of sodium dodecyl sulphate (SDS) with Astra Phloxine FF reagent at pH 3–8, followed by liquid–liquid microextraction of the formed ion associate into an organic phase containing a mixture of carbon tetrachloride and dichloroethane (4:1, v/v) and subsequent UV-Vis detection at 555 nm. The calibration plot was linear in the range 0.006–0.29 mg L^?1 of SDS. The limit of detection (LOD), calculated based on 3s, is 0.002 mg L^?1. The method was applied to the determination of anionic surfactants in real wastewater samples.     

Decolorization of Reactive Black 5 and Reactive Blue 4 Dyes in Microbial Fuel Cells

Microbial fuel cells (MFCs) have potential to treat industrial wastewater containing organic compounds and simultaneously generate power. Organic compounds include textile dyes with various chromophore groups, which can be decolorized reductively by microorganisms under anaerobic conditions. In the present study, we examined the decolorization of Reactive Black 5 (RB5) azo dye and Reactive Blue 4 (RBL4) anthraquinone dye under open circuit potential in MFCs with graphite plate and graphite felt electrodes and a microbial consortium originally derived from bovine rumen fluid. RB5 dye was more than 90% decolorized in 120, 165, and 225 min at 50, 100, and 200 mg L^?1 concentrations, respectively. RBL4 dye at 50 and 100 mg L^?1 took 225 and 300 min to decolorize, while 200 mg L^?1 RBL4 dye was not decolorized at all. Under closed circuit conditions, decolorization increased with decrease in external load, whereas current generation increased with external resistance. The results demonstrate that the reductive cleavage of the chromophore was more rapid with RB5 than with RBL4.     

Miniaturized and green method for determination of chemical oxygen demand using UV-induced oxidation with hydrogen peroxide and single drop microextraction

We report on a green method for the determination of low levels of chemical oxygen demand. It is based on the combination of (a) UV-induced oxidation with hydrogen peroxide, (b) headspace single-drop microextraction with in-drop precipitation, and (c) micro-turbidimetry. The generation of CO₂ after photolytic oxidation followed by its sequestration onto a microdrop of barium hydroxide gives rise to a precipitate of barium carbonate which is quantified by turbidimetry. UV-light induced oxidation was studied in the absence and presence of H₂O₂, ultrasound, and ferrous ion. Determinations of chemical oxygen demand were performed using potassium hydrogen phthalate as a model compound. The optimized method gives a calibration curve that is linear between 3.4 and 20 mg L^?1 oxygen. The detection limit was 1.2 mg L^?1 of oxygen, and the repeatability (as relative standard deviation) was around 5 %. The method was successfully applied to the determination of chemical oxygen demand in different natural waters and a synthetic wastewater.

Generating aerodynamic surrogate nuclear explosion debris (SNED)

In this work, a brand new organic superficial active sorbent l-Cysteine hydrochloride modified bentonite (LCMB) has been developed and proposed for treatment of contaminated water containing uranium. Correlation between different factors such as pH, contact time, temperature, initial concentration of U(VI) and efficiency of LCMB for uranium absorption are discussed. At uranium content in water from 25 to 250 mg L^?1, the sorption capacity for LCMB reached 208.3 mg g^?1 that is essentially higher in comparison with other sorbents and notably improved from 77 mg g^?1 after modification.     

A Phenylurea Cytokinin,CPPU, Elevated Reducing Sugar and Correlated to Andrographolide Contents in Leaves of <Emphasis Type="Italic">Andrographis paniculata</Emphasis> (Burm. F.) Wall. Ex Nees

Cytokinins are phytohormones that play multiple roles to control plant growth and development. In this study, leaf biomass and the production of andrographolide compounds in a medicinal plant Andrographis paniculata were significantly increased after exogenously treating with the synthetic cytokinin cytokinin-1-(2-chloro-4-pyridyl)-3-phenylurea (CPPU) at 0 (water), 5, or 10 mg L^?1 and observed the results for 24 h, 48 h, and 7 days of treatment. It was found that CPPU could significantly enhance new axillary bud formation and further promote branching 4.6–5.6-fold higher, resulting in higher fresh weight (FW) and dry weight (DW) than the control. Application of CPPU at 5 mg L^?1 significantly promoted the highest contents of total reducing sugar at 2.5-fold in leaves and at 1.5-fold in roots. Although treatments of CPPU significantly affected the increasing contents of chlorophyll and carotenoid (1.2–1.6-fold), CPPU at 10 mg L^?1 slightly caused leaf stress and chlorophyll reduction. Interestingly, 5 mg L^?1 CPPU could enhance andrographolide content, an active anti-infectious compound in Andrographis paniculata (2.2-fold higher than the control) that reached the highest content at 24 h after treatment. This study suggested that CPPU should be suitable for field application to promote leaf yields and induce the production of useful pharmaceutical compounds in Andrographis paniculata.     

Electrochemical determination of picric acid based on platinum nanoparticles–reduced graphene oxide composite

Platinum nanoparticles–reduced graphene oxide composite-modified glassy carbon electrode (PtNPs–rGO/GCE) was developed as a simple, selective and sensitive electrochemical sensor for determination of picric acid (PA). Cyclic voltammogram (CV) of PA showed three well-defined irreversible reduction peaks at the potentials of ?0.43, ?0.57 and ?0.66 V versus Ag/AgCl. In this work, the interference effect of other nitrophenol compounds (NPhCs) was significantly reduced by appropriate adjusting of pH. Square wave voltammetry was used for quantification of PA in the range of 5–500 µM (1.15–115 mg L^?1) with practical detection limit of 1 µM (0.23 mg L^?1). The proposed sensor was successfully applied for the determination of PA in two natural water samples.     

Simultaneous CE Determination of Captopril and Indapamide in Pharmaceuticals and Human Plasma

Capillary electrophoresis with UV photo diode-array detection was utilized to adopt a new method for the assay of captopril and indapamide in pharmaceuticals and human plasma. Electrophoretic conditions controlling the analysis were optimized to develop separation, sensitivity and rapidity. The optimum conditions obtained were 100 mM borate at pH 9.0, injection time 10.0 s, voltage 25 kV and column temperature 25 °C with detection at 220 nm. Relatively, wide dynamic ranges for captopril (1–100 mg L^?1) and indapamide (0.1–40 mg L^?1) were obtained. Also, the method recorded acceptable intra- and inter-day accuracy (89.8–97.9%) and precision (0.77–3.50%) in pharmaceutical formulations and human plasma. The sensitivity of the method was developed by the optimization and the preconcentration conducted for human plasma sample using liquid–liquid extraction. The limit of detection gained (0.075 and 0.045 mg L^?1 for captopril and indapamide, respectively) reached the level of both drugs possibly found in human plasma. The method is suitable to be applied in pharmaceutical industries for quality control and in clinical laboratories for therapeutic drug monitoring purposes.     

Determination of Trenbolone Acetate in Cattle Feeds by a Flow Injection Chemiluminescence Method

A flow injection chemiluminescence (CL) method is described for the determination of trenbolone acetate based on the CL generated during its reaction with KMnO₄ in acidic medium. The CL intensity is greatly enhanced by alizarin yellow R. The CL intensity is linear with trenbolone acetate concentration in the range 0.1–100.0 mg L^?1 with a detection limit of 0.05 mg L^?1. The sample throughout is about 90 h^?1 and the relative standard deviation for 2.0 mg L^?1 trenbolone acetate solution is 1.5% (n = 11). The proposed method was applied to the determination of trenbolone acetate in cattle feeds.     

Application of Physicochemical Treatment Allows Reutilization of <Emphasis Type="Italic">Arthrospira platensis</Emphasis> Exhausted Medium

Since cultivations of Arthrospira platensis have a high water demand, it is necessary to develop treatment methods for reusing the exhausted medium that may prevent environmental problems and obtaining useful biomass. The exhausted Schlösser medium obtained from A. platensis batch cultivation in bench-scale mini-tanks was treated by varying concentrations of different coagulants, ferric chloride (6, 10, and 14 mg L^?1) or ferric sulfate (15, 25, and 35 mg L^?1) and powdered activated carbon (PAC, 30 and 50 mg L^?1). Such treated effluent was restored with NaNO₃ and reused in new cultivations of A. platensis performed in Erlenmeyer flasks. Reusing media through the cultivation of A. platensis showed satisfactory results, particularly in the medium treated with ferric chloride and PAC. The maximum cell concentration obtained in the flasks was 1093 mg L^?1, which corresponded to the medium treated with ferric chloride (6 mg L^?1) and PAC (30 mg L^?1). This cellular growth was higher than in the medium treated with ferric sulfate and PAC, in which values of maximum cell concentration did not exceed 796 mg L^?1. The cultures in the media after treatment did not modify the biomass composition. Thus, combined coagulation/adsorption processes, commonly used in water treatment processes, can be efficient and viable for treating exhausted medium of A. platensis, allowing the production of such biomass with the reduction of production cost and saving water.     

Detection of Aryloxyphenoxypropionate Herbicides by Enzyme-Linked Immunosorbent Assay

In this study, we developed a general and broad class-selective indirect competitive enzyme-linked immunosorbent assay (ic-ELISA) for detecting aryloxyphenoxypropionate herbicides. A multideterminant artificial antigen was prepared from haptens of two herbicides (fenoxaprop-p-ethyl and cyhalofop-butyl) conjugated to the carrier protein Bovine serum albumin (BSA). The polyclonal antibodies (PAbs) were obtained by immunizing New Zealand white rabbits. Characterization studies of the PAbs showed that they had high affinity and specificity for the two herbicides. The 50% inhibitory concentration (IC₅₀) values for fenoxaprop-p-ethyl and cyhalofop-butyl were 0.185 mg L^?1 and 0.045 mg L^?1 with a limit of detection (LOD, IC₁₀) of 0.004 mg L^?1 and 0.002 mg L^?1, respectively. There were no obvious cross-reactivities with most of the aryloxyphenoxypropionates tested, except for metamifop (CR% = 55.56%). The recoveries of fenoxaprop-p-ethyl, cyhalofop-butyl and metamifop in environmental and agricultural samples (tap water, paddy water, soil, rice and soybean) ranged from 86.86–114.52%, 82.07–119.11% and 82.51–114.46%, respectively. These results demonstrate that the established ELISA could be used as a tool for detecting aryloxyphenoxypropionate multiresidues.     

A colorimetric probe for ascorbic acid based on copper-gold nanoparticles in electrospun nylon

We report on a colorimetric probe based on copper-gold alloy nanoparticles (NPs). The probe is capable of selectively detecting ascorbic acid (AA) as a result of the distance-dependent colour change of the nanoparticles immobilized in an electrospun nylon-6 nanofiber. The resulting white nanofibres undergo a colour change to blue as a result of the aggregation of the NPs induced by AA in the pH range 2–7. The probe is selective for AA even in the presence of dopamine, uric acid, saccharides, amino acids and certain organic acids. It covers the 1.76 x10^?2 mg L^?1 to 1.76 x10⁵ mg L^?1 concentration range, and exhibits a limit of detection of 1.76 x10^?2 mg L^?1 based on visual detection. Its application was demonstrated by the determination of ascorbic acid in fruit juices, urine, serum, and vitamin C tablets.

Isolation of a Methylobacterium organophilium strain, and its application to a methanol biosensor

A methanol-utilizing strain (ME25) using methanol (MeOH) as the sole carbon source has been isolated from methane-generating pits. ME25 was identified as Methylobacterium organophilium by its physiological characteristics and 16SrDNA sequence. A MeOH biosensor was then developed by immobilizing ME25 along with sensor for dissolved oxygen (O₂). Its response is based on the depletion of O₂ following oxidation of MeOH by the bacteria. The decrease in O₂ is linearly related to the MeOH concentration in the range from 1.6 mg·L^?1 to 4800 mg·L^?1 and the detection limit for MeOH is 0.27 mg·L^?1. The response time of the biosensor is around 20 min.     

Carbon ceramic electrodes modified with mixed oxides SiO<Subscript>2</Subscript>/SnO<Subscript>2</Subscript> for determination of levofloxacin

The preparation of a carbon ceramic electrode modified with SnO₂ (CCE/SnO₂) using tin dibutyl diacetate as precursor was optimized by a 2³ factorial design. The factors analyzed were catalyst (HCl), graphite/organic precursor ratio, and inorganic precursor (dibutyltin diacetate). The statistical treatment of the data showed that only the second-order interaction effect, catalyst × inorganic precursor, was significant at 95% confidence level, for the electrochemical response of the system. The obtained material was characterized by scanning electron microscopy (MEV), X-ray diffraction (XRD), RAMAN spectroscopy, XPS spectra, and voltammetric techniques. From the XPS spectra, it was confirmed the formation of the Si–O–Sn bond by the shift in the binding energy values referred to Sn 3d3/2 due to the interaction of Sn with SiOH species. The incorporation of SnO₂ provided an increment of the electrode response for levofloxacin, with Ipa = 147.0 μA for the ECC and Ipa = 228.8 μA for ECC/SnO₂, indicating that SnO₂ when incorporated into the silica network enhances the electron transfer process. Under the optimized working conditions, the peak current increased linearly with the levofloxacin concentration in the range from 6.21×10^?5 to 6.97×10^?4 mol L^?1 with quantification and detection limits of 3.80×10^?5 mol L^?1 (14.07 mg L^?1) and 1.13×10^?5 mol L^?1 (4.18 mg L^?1), respectively.