Kinetic-Spectrophotometric Determination of Molybdenum(VI) Based on Its Catalytic Effect on the Thionine-Hydrazine Reaction

Abstract

A kinetic method for the determination of trace amounts of Mo(VI) (0.05-4 μg ml^?1) based on its catalytic effect on the reduction of thionine by hydrazine monochloride in strongly acidic media is reported. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of thionine at 605 nm after a fixed time (5 min.). The detection limit of the method is 23 ng ml^?1 and the relative standard deviation (RSD) for 0.05 μg ml^?1 of Mo(VI) is 1.2% (n=7). The method is almost free from interferences, especially from large amounts of tungsten. The procedure was successfully applied to the determination of trace amounts of molybdenum in steel.     

Simultaneous Determination of Perphenazine and Amitriptyline by Derivative Spectrophotometry

Abstract

Two methods have been developed for the simultaneous determination of Amitryptiline and Perphenazine: the zero-crossing (I) and the derivative ratio spectrum (II) methods and both use the derivative spectrophotometry.

The methods have been applicable in the ranges of 1 to 30 μg·ml^?1 of Amitryptiline (I and II) and between 1 and 8 μg·ml^?1 and from 1 to 7 μg·ml^?1 of Perphenazine for the methods I and II respectively. The accuracy of the proposed methods have been studied and they have been used in the determination of Amitryptiline and Perphenazine in commercially available pharmaceuticals.     

Utility of p-chloranilic Acid and 2,3 Dichloro-5,6-dicyano p-Benzoquinone (DDQ) for the Spectrophotometric Determination of Triamterene

Abstract

Two simple and sensitive spectrophotometric procedures are suggested for analysis of triamterene. The first procedure is based on the reaction of triamterene with p-chloranilic acid (p-CA) in methylene chloride to form a highly stable coloured product, exhibiting maximum absorbance at λ 530 nm. Beer's law is obeyed in the range of 40–220 μg.ml^?1 with a mean percentage accuracy of 99.98 ± 0.446. Limit of determination is 20 μg.ml^?1. In the second procedure, the drug is determined via charge transfer complex formation with 2,3 dichloro-5,6-dicyano p-benzoquinone (DDQ) using methylene chloride as a solvent. Here the reaction product has two well defined maxima at 460 nm and 530 nm where each has been utilized for quantitative determination. Beer's law is obeyed in concentration ranges of 25–125 μg.ml^?1 and 25–150 μg.ml^?1 with mean percentage accuracies of 99.92 ± 0.449 and 100.00 ± 0.511 for both maxima. 460 and 530 nm. respectively. Limit of determination is 12.5 μg.ml^?1 at both maxima. Optimum conditions for each procedure have been studied and the stoichiometry of both reactions was ascertained using Job's method of continuous variation. The validity of the suggested procedures was assessed by applying the standard addition technique using the drug capsules. Both procedures are statistically analyzed as compared with BP method for analysis of triamterene (non aqueous titration) revealing good accuracy and precision as indicated by t and F tests.     

Simultaneous determination of metal ions. Catalytic oxidation of cobalt by metal ions when extracted with quinolin-8-ol

The catalytic effect of various ions on the aerial oxidation of Co(II) when extracted from weakly acidic solutions with quinolin-8-ol in chlorofom was studied. Oxidation is complete only in the presence of Fe(III) or V(V). Mixtures of Al(III), Cu(II), Fe(III) and Ni(II) with Co(II) at concentrations in the range 1–8 μg ml^?1 were analysed by using a multi-component analysis program involving first-order derivative spectra. Because of the metal ion interaction, a multivariate calibration process is required. The recovery factors achieved ranged from 93 to 111%.     

Some Arylidene-2-Pyridylhydrazone Derivatives as Reagents for Spectrophotometric Determination of Palladium (II)

Abstract

A method for spectrophotometric determination of palladium by complexation with Arylidene-2-pyridylhydrazone derivatives in 50% (V/V) ethanolic solution are described-Pd(II) forms a 1:1 complex with the reagents. Beer's law is obeyed over the range 0.2-6.5 μg ml^?1. The effect of pH, effect of excess reagent, stability of complexes as well as the tolerance amount of many metal ions have been reported. The method is applied, with fair accuracy, to the determination of pd(II) in synthetic solutions.     

Flame atomic absorption spectrometric determination of Cd(II), Ni(II), Co(II) and Cu(II) in tea and water samples after simultaneous preconentration of dithizone loaded on naphthalene

A simultaneous preconcentration procedure for the determination of Cd(II), Ni(II), Co(II) and Cu(II) by atomic absorption spectrometry is described. The method is based on solid phase extraction of the metal ions on dithizone loaded on naphthalene in a mini-column, elution with nitric acid and determination by flame atomic absorption spectrometry. The sorption conditions including NaOH concentration, sample volume and the amount of dithizone were optimized in order to attain the highest sensitivity. The calibration graph was linear in the range of 0.5–75.0 ng ml^?1 for Cd(II), 1.0–150.0 ng ml^?1 for Ni(II), 1.0–150.0 ng ml^?1 for Co(II) and 1.0–125.0 ng ml^?1 for Cu(II) in the initial solution. The limit of detection based on 3S_b was 0.13, 0.32, 0.33 and 0.43 ng ml^?1 for Cd(II), Ni(II), Co(II) and Cu(II), respectively. The relative standard deviations (R.S.D) for ten replicate measurements of 20 ng ml^?1of Cd(II), 100 ng ml^?1 of Ni(II), Co(II) and 75 ng ml^?1 of Cu(II) were 3.46, 2.43, 2.45 and 3.26%, respectively. The method was applied to the determination of Cd(II), Ni(II), Co(II) and Cu(II) in black tea, tap and river water samples.     

Spectrophotometric determination of cobalt(II) based on the ion-pair of tetrathiocyanatocobaltate(II) with neotetrazolium chloride

The ion-pair formed between tetrathiocyanatocobaltate(II) and [3,3′-(4,4′- biphenylene)bis(2,5-diphenyl)]-2H-tetrazolium chloride (neotetrazolium chloride) can be extracted into 4-methylpentan-2-one and used for the spectrophotometric determination of cobalt (2.5–9.8 μg ml^?1) at pH 3.5–5.0. The Sandell sensitivity of the method is 0.02 μg Co cm^?2. With suitabte masking, the method is quite selective and is applicable to nickel wire alloys.     

The spectrophotometric determination of vanadium after extraction as vanadium(III) ferronate by tribenzylamine

Vanadium(III) obtained by dithionite reduction of vanadium(V) can be extracted as its ferron complex with tribenzylamine in chloroform from 0.05 M sulphuric acid. Vanadium (0–5 μg ml^-1) is determined spectrophotometrically at 430 nm with a sensitivity of 0.0028 μg V cm^-2. Al(III), Co(II), Ni(II), Fe(II, III), Hg(II), Si(IV), Be(II), Mg(II), Ca(II), Sr(II), Ba(II), Cr(VI, III), W(VI), Zn(II), U(VI), Mn(II). Pb(II), Cu(II), Cd(II) and Th(IV) do not interfere; only Mo(VI), Ti(IV), Zr(IV). Bi(V) and Sn(II) interfere. A single determination takes only 7 min. The extracted complex is V^III (R-3H.TBA)₃ where R = C₉H₄O₄NSI. The method is satisfactory for the determination of vanadium in steels, alum and other samples without preliminary separations.     

Zero-Crossing Derivative Spectrophotometric Determination of Mercury(II) And Palladium(II) with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1-3-thiazolidine and Cetyltrimethylammonium Bromide

Abstract

A method is proposed for the simultaneous determination of mercury(II) and palladium(II) by first-derivative spectrophotometry based on the absorption spectra of their complexes with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1,3-thiazolidine [5-(3,4-methoxyhydroxybenzylidene) rhodanine]. Zero-crossing measurement technique is found suitable for the measurement of the first-derivative value at the specified wavelengths. Mercury(II) (0.4-1.4 μg ml^?1) and palladium(II) (0.08 - 1.8 μg ml^?1) in different ratios have been determined simultaneously. A critical evaluation of the proposed method is performed by statistical analysis of the experimental data.     

2-(2-Thiazolylazo)-p-cresol(TAC) as a Reagent for the Spectrophotometric Determination of Lead(II)

Abstract

The reaction between lead(II) and 2-(2-Thiazolylazo)-p-Cresol(TAC) in the presence of TERGITOL NPX (4 mg/ml) at an apparent pH 9.0–10.0 results in an intensely colored complex which is stable for at least 4 hr.

The composition of the complex is 1:2 cation: TAC and the log of the formation constant is 11.92 ± 0. 40. Beer's law is obeyed up to 6.0μg.ml^?1 of lead(II) at 650nm.

The apparent molar absorptivity at 650 nm is 2.07 × 10⁴ 1. mole^?1.cm^?1 and the detection limit was obtained as 10.0 ng.ml^?1 of lead(II).

The method is applied to determination of lead(II) in copper-base alloy.     

Rapid spectrophotometric determination of ruthenium(III) with prochlorperazine maleate

A rapid, simple spectrophotometric method for the determination of μg amounts of ruthenium, based on the formation of a pink complex between the metal and prochlorperazine maleate (PCPM) in sulphuric or hydrochloric acid solution, is described. The complex has an absorption maximum at 530 nm and its molar absorptivity is 6.733·10³ l mol^?1 cm^?1. The sensitivity is 0.0151 μg Ru cm^?2 for log I_o/I = 0.001. Beer's law is valid over the range 0.2–10 μg Ru ml^?1 ; the optimal range for spectrophotometric determination is 0.8–8.0 μg Ru ml^?1. Job's method of continuous variation, the mole ratio method and the slope ratio method indicate a 1:1 composition for the complex. The effects of acidity, time, temperature, order of addition of reagents, reagent concentration, and the interferences from various ions are reported.     

Color Reaction Between 4-(2-Pyridylazo)Resorcinol and Mercury (II) in the Presence of Surfactant,and Improved Spectrophotometric Determinations of Mercury(II) and Cyanide Ion with its Coloring

Abstract

The reactions among 4-(2-pyridylazo)resorcinol (PAR), mercury(II) and/or cyanide ion in the presence of water soluble surfactants alone or combination were systematically investigated at about pH 9. The spectrophotometric determinations of mercury(II) and cyanide ion were investigated by using the PAR-mercury(II)-HPC complex (3:2:2 molar ratio) in the presence of N-hexadecylpyridinium chloride (HPC) alone; calibration graphs were rectilinear in the ranges of 0 – 40 μg mercury(II) and 0 –10 μg cyanide ion in a final 10 ml with the apparent molar absorptivities of 5.9 × 10⁴ for mercury(II) and 2.5 × 10⁴ 1 mol^?1 cm^?1 for cyanide ion at 590 nm. The proposed method had advantages—rapidity, simplicity without solvent extraction, and sensitivity in comparison with reported solvent extraction methods. The interference of foreign ions decreased 1/2–l//4-fold compared with that in the presence of non-ionic surfactant alone.     

Spectrophotometric Determination of Uranium(VI) with Chlorophosphonazo-mN by Flow Injection Analysis

Abstract

A sensitive and selective spectrophotometric flow injection analysis (FIA) method with chlorophosphonazo-mN has been developed for the determination of uranium(VI) in standard ore samples. Most of interfering ions are effectively eliminated by the masking reagent of diethylenetriaminepentaacetic acid (DTPA). In the U(VI)-chlorophosphonazo-mN system, the maximum absorption wavelength is at 680 nm and Beer's law is obeyed in the range of 1 to 15 μg ml^?1. The correlation coefficient of the calibration curve is 0.9998, the sampling frenquency is 60 h^?1, and the detection limit for uranium(VI) is 0.5 μg ml^?1. The composition of the U(VI)-chlorophosphonazo-nN complex was established to be 1:2 by flow-through spectrophotometric and conventional molar ratios methods.     

Biomethylation and biotransformation of arsenic in a freshwater food chain: Green alga (chlorella vulgaris)→shrimp (neocaridina denticulata)→killifish (oryzias iatipes)

Tolerance, bioaccumulation, biotransformation and excretion of arsenic compounds by the fresh–water shrimp (Neocaridina denticulata) and the killifish (Oryzias latipes) (collected from the natural environment) were investigated. Tolerances (LC₅₀) of the shrimp against disodium arsenate [abbreviated as As(V)], methylarsonic acid (MAA), dimethylarsinic acid (DMAA), and arsenobetaine (AB) were 1.5, 10, 40, and 150μg As ml^?1, respectively. N. denticulata accumulated arsenic from an aqueous phase containing 1 μg As ml^?1 of As(V), 10 μg As ml^?1 of MAA, 30 μg As ml^?1 of DMAA or 150 μg As ml^?1 of AB, and biotransformed and excreted part of these species. Both methylation and demethylation of the arsenicals were observed in vivo. When living N. denticulata accumulating arsenic was transferred into an arsenic–free medium, a part of the accumulated arsenic was excreted. The concentration of methylated arsenicals relative to total arsenic was higher in the excrement than in the organism. Total arsenic accumulation in each species via food in the food chain Green algae (Chlorella vulgaris) → shrimp (N. denticulata) → killifish (O. latipes) decreased by one order of magnitude or more, and the concentration of methylated arsenic relative to total arsenic accumulated increased successively with elevation in the trophic level. Only trace amounts of monomethylarsenic species were detected in the shrimp and fish tested. Dimethylarsenic species in alga and shrimp, and trimethylarsenic species in killifish, were the predominant methylated arsenic species, respectively.     

Spectrophotometric Determination of Diphenadione Via its Metal Complexes

Abstract

Spectrophotometric procedure is described for the quantitative determination of diphenadione [2-(diphenylacetyl)-1,3-indandione], based on direct spectrophotometric measurements of the absorbances of its iron (III), iron (II) and cobalt (II), metal complexes at 488 nm, 505 nm and (334 nm, 372 nm), respectively. The drug reacts with metals in the ratio of 3:1 and 2:1 for iron (III) and for both iron (II) and cobalt (II) respectively. The obtained complexes have apparent molar absorptivities of 1.48 × 10³ 1 mol^?1 cm^?1, 0.714 × 10³ 1 mol^?1cm^?1 and (1.70 × 10³ 1 mol^?1cm^?1, 1.93 × 10³ 1 mol^?1cm^?1) for iron (III), iron (II) and cobalt (II) complexes, respectively. The procedure is suggested for the determination of 51–400 μg.ml^?1 diphenadione via the iron (II) complex and 35–170 μg.ml^?1 diphenadione via both cobalt (II) and iron (III) complexes. The suggested procedure has accuracies of 99.79 ± 0.67%, 99.64 ± 0.37% and (100.09 ± 0.53%, 99.99 ± 0.42%) for the metal complexes of iron (III), iron (II) and cobalt (II), respectively.     

Flow-injection spectrophotometric determination of cobalt by extraction as tetrathiocyanatocobaltate(II) with the ethylenebis(triphenylphosphoniu) cation

Cobalt (0–10 μg) may be determined spectrophotometrically at 625 nm after flow-injection extraction into chloroform of the ion associate ethylenebis(triphenylphosphonium) tetrathiocyanatocobaltate(II). The carrier stream contained 10% (w/v) ammonium fluoride and the reagent stream contained 0.5% (w/v) ethylenebis (triphenylphosphonium) bromide and 5% (w/v) ammonium thiocyanate. The injection rate was 20 h^?1. The calibration graph is linear up to 20 μg ml^?1 and detection limit is 0.23 μg ml^?1 cobalt, based on injection volumes of 500 μl. The system has been applied to the determination of cobalt in a range of tool steels.     

Square‐Wave Adsorptive‐Stripping Voltammetric Detection in the Quality Control of Fluoxetine

ABSTRACT

A simple and sensitive extraction-spectrophotometric method for the determination of barium and potassium is reported. The 18C6-Barium-Orange II (18C6-Ba-(OR II)₂) and 18C6-Potassium-Orange II (18C6-K-OR II) ternary complexes are quantitatively extracted into dichloromethane and their absorbances are measured at 483 nm. Linear calibration graphs were obtained over the barium concentration range of 0.1-5 μg ml^?1 and potassium concentration range of 1-8 μg ml^?1. The relative standard deviation for 2.0 μg ml^?1 barium and pottasium are, respectively, 4.16% and 3.60%. The interfering effect of a large number of diverse ions on the determination of barium and potassium was studied. The method was applied to a synthetic sample with natural matrix effects of tap water and the results showed high potential of the recommended method for the determination of Ba and K in water samples.     

Spectrophotometric Determination of Sparfloxacin in Pharmaceutical Preparations by Ternary Complex Formation with Pd(II) and Eosin

Abstract

A simple, sensitive, and direct spectrophotometric method has been developed for the assay of sparfloxacin in bulk and pharmaceutical preparations. The proposed method is based on the formation of ternary complex between an investigated drug, palladium(II) ion and eosin in the presence of methylcellulose as surfactant and acetate buffer of pH 4.2. Spectrophotometrically, under the optimum conditions, the ternary complex showed absorption maximum at 550 nm, with apparent molar absorptivity of 2.69×10⁴ l mol^?1 cm^?1, Sandell's sensitivity of 0.01458 µg ml^?1 and linearity in the concentration range 1.6–16 µg ml^?1. The composition of the ternary complex was studied by Job's method of continuous variation and the result indicated that the molar ratio of SPFX: Pd: eosin is 1∶1∶1. The optimum reaction conditions and other analytical parameters are evaluated. The proposed method was successfully applied for the determination of SPFX in its pharmaceutical product with mean percentage recoveries of 99.71%. The observed data has been subjected to statistical analysis, which revealed high accuracy and precision.     

Colorimetric Determination of Propofol in Bulk form,Dosage Form and Biological Fluids

ABSTRACT

Propofol is coupled with 2, 6-dichloroquinone-4-chlorimide (DCQ) in a reaction buffered at pH 9.6 to give a colored product having an analytically useful maximum at 635 nm. The factors affecting the color generation were optimized and incorporated in the procedure. The reacted propofol has a molar absorptivity of 3.9 × 10^?4 L mol^?1 cm^?1, and Beer's law is obeyed for concentrations 1-5 μg ml^?1 with detection limit 0.25 μg ml^?1. The method was found applicable to biological fluids (plasma and urine) spiked with propofol at concentration levels 1-5 μg ml^?1 for plasma and 1-5 μg 0.5 ml^?1 urine (less sensitivity is obtained with urine volumes above 0.5 ml) with detection limits 0.28 μg ml^?1 for plasma and 0.4 μg 0.5 ml^?1 urine. The average recovery for the commercial preparation (1% w/v propofol emulsion intravenous injection for infusion) was 99.54% with an RSD of 1.05%. The method was validated by an adopted HPLC method. The results obtained by the HPLC method for the commercial preparation were statistically compared with the proposed method and evaluated at the 95% confidence limits.     

Fluorescent Complexes of Nucleic Acids/8-Hydroxyquinoline/Lanthanum(III) and the Fluorometry of Nucleic Acids

Abstract

The ternary fluorescent complexes of nucleic acids/8-hydroxyquinoline/ lanthanum (III) were studied. Nucleic acids in the study involve natured and thermally denatured calf thymus DNA, fish sperm DNA and yeast RNA. In the range of pH 8.0–8.4 (controlled by NH₃-NH₄Cl buffer) ternary fluorescent complexes are formed which emit at 485.0 nm for calf thymus DNA and at 480.0 nm for yeast RNA (when excited at 267.0 nm) and emits at 483.0 nm for fish sperm DNA when excited at 265.0 nm. Based on the fluorescence reactions sensitive fluorometric methods for nucleic acids were proposed. Using optimal conditions, the calibration curves were linear in the range of 0.4–3.6 μg˙ml^?1 for calf thymus DNA, 0.4–4.0 μg-ml^?1 for fish sperm DNA and 0.4–4.0 μg˙ml^?1 for yeast RNA, respectively. The limits of determination (3σ) were 0.076 μg˙ml^?1 for calf thymus DNA, 0.068 μg˙ml^?1 for fish sperm DNA and 0.329 μg˙ml^?1 for yeast RNA, respectively. Five synthetic samples were determined with satisfaction.