Analytical Determination of Polycyclic Aromatic Hydrocarbons in Gases from Coal Conversion by Synchronous Fluorescence Spectrometry.

Abstract

A method to analyze the most hazardous Polyclyclic Aromatic Hydrocarbons (PAH) (acenaphtene, anthracene, benzo(a) anthracene, benzo(a)pyrene, biphenyl, coronene, chrysene, dibenzo (a,h) anthracene, phenantrene, fluoranthene, fluorene, naphtalene and pyrene), by using excitation and energy constant synchronic fluorescence has been researched in depth in this study.

Spectral studies carried out allow characteristic peaks to be obtained for the qualitative identification of 8 from 11 PAH tested. From the quantitative and interference studies, the most important analytical characteristics (linear range, detection limit and reproduciblity) for the determination of ten of these compounds have been obtained.

The method was applied to the PAH determination in two different samples: 1) air filter samples for urban pollution control and 2) air samples from a laboratory scale coal carbonization oven. Fluorene (in the first type) and benzo (a) pyrene (in the second type), were identified and quantified.     

Use of Micelles in the TLC Separation of Polynuclear Aromatic Compounds and Amino Acids

Abstract

The polynuclear aromatic compounds (PNA): anthracene, napthalene, phenanthrene, pyrene, pyrenecarboxaldehyde, benzo (a) pyrene, benzo (e) pyrene, perylene and fluorene can be chromatographed on polyamide TLC sheets using an aqueous micellar solution cf sodium dodecylsulfate (SDS) as the mobile phase. Reversed micellar solutions (of sodium dioctylsulfosuccinate) were used in a reverse phase chromatographic separation of amino acids. Some amino acids tended to streak slightly rather than move as discrete spots. Conditions could be adjusted, however, so that most of the amino acids and all PNA's would move as spots.     

Determination of Polycyclic Aromatic Hydrocarbons in Airborne Particulate by High Performance Liquid Chromatography

This paper presents a trisolvent ultrasonic extraction and HPLC analysis method for the determination of 11 polycyclic aromatic hydrocarbons in air particulate collected on an air filter by a commercial high volume air sampler. A reverse phase column, Vydac 201 TP, and a gradient mobile phase, acetonitrile/water, were used. The 11 PAHs, fluoranthene, pyrene, benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a, h]anthracene, benzo[ghi]perylene, indeno[1,2,3-cd]pyrene, and coronene were completely resolved under experimental conditions. All the PAHs except coronene were monitored by fluorescence with λ_ex=270 nm, λ_em>389 nm. Coronene was monitored by UV with λ=300 nm. The methodology was evaluated by spiking SRM 1649 with a PAH standard and then going through different extraction procedures and analyzing the PAH concentrations without clean-up. An external standard method was used for quantitation. The recovery yields for fluoranthene, benz[a]anthracene, benzo[a]pyrene, benzo[ghi]perylene and indeno[l,2,3-cd]pyrene were above 90%. The detection limits of PAH with fluorescence at λ_ex=270 nm, λ_em>389 nm ranged from 5.7 pg to 69.5 pg.     

A novel application of nylon membranes to the luminescent determination of benzo[a]pyrene at ultra trace levels in water samples

Very simple and highly sensitive methods are presented for the determination of benzo[a]pyrene, one of the most carcinogenic polycyclic aromatic hydrocarbons (PAHs). The approaches are based on solid-phase extraction of the analyte on a nylon membrane via a syringe procedure, and its fluorescent or phosphorescent determination on the solid surface. While the native fluorescence of benzo[a]pyrene retained on a nylon surface is measured directly, room-temperature phosphorescence is induced by spotting a few microlitres of thallium(I) nitrate solution on the surface (heavy-atom effect). An enhancement of the phosphorescence signal was corroborated when the measurements were carried under a nitrogen atmosphere. The analytical figures of merit obtained under the best experimental conditions demonstrate the capability of detecting benzo[a]pyrene at a sub-parts-per-trillion (sub-ng L⁻¹) level. The potential interference from other common PAHs and also from different metal ions was studied. The feasibility of determining benzo[a]pyrene in real samples was successfully evaluated through the analysis of spiked tap, underground and mineral water samples of different origins. Recoveries obtained from spiked river waters were successfully compared with those provided by a reference method, through rigorous statistical analysis.     

Determination of Benzo(a)Pyrene and other Polynuclear Aromatic Hydrocarbons in Airborne Particulate Material by Ultrasonic Extraction and Reverse Phase High Pressure Liquid Chromatography

Abstract

Ultrasonic extraction of airborne particulate material on Hi-Vol filters is described. Almost all of the polar compounds are removed during the extraction by adsorption on the surface of the shredded glass fibers and controlled pore glass powder (CPG). The non-polar polynuclear aromatic hydrocarbons (PAH) in the extract are separated at room temperature by high pressure liquid chromatography (HPLC) on reverse phase Vydac using acetonitrile:water (70:30 v/v) as the chromatographic solvent. There is baseline separation of benzo(a)pyrene (BaP), benzo(k)fluoranthene (BkFt) and of benzo(e)pyrene (BeP), benzo(b)fluoranthene and perylene, the latter three present in one band. Extracts of airborne particulates show the same peaks. BaP elutes in approximately 14 minutes. Precision and accuracy measurements indicate full recovery of PAH and good extraction reproducibility. The detection limit of BaP at F 290/389 is less than 10 pg. Total analysis time is approximately 1 1/2 hr, most of which is waiting time.     

Simultaneous Determination of Phenanthrene and Benzo(a)pyrene in Water Samples by Synchronous Fluorescence Spectroscopy

Abstract

A simple and sensitive method was developed to simultaneously determine phenanthrene and benzo(a)pyrene in water samples using synchronous fluorescence spectroscopy with a 56-nm Δλ. The method was used to simultaneously determine both compounds in samples of spiked surface water. Analytical recoveries were 96.9–101.1% for phenanthrene and 95.8–103.5% for benzo(a)pyrene. Analytical results were checked for precision with 15 measurements for each compound. Relative standard deviations were 1.9% for phenanthrene and 2.9% for benzo(a)pyrene, which shows that the proposed method is quite precise.     

Atmospheric levels of polycyclic aromatic hydrocarbons in gas and particulate phases from Tarragona Region (NE Spain)

The atmospheric levels of polycyclic aromatic hydrocarbons (PAHs) in atmospheric samples taken at two urban sites and two sites near industrial areas of the Tarragona region (Catalonia, Spain), where one of the most important petrochemical complexes in the south of Europe is located, were determined. Gas and particulate phase of air were separately sampled and analysed. Concentrations of 16 PAHs studied ranged from 4.2 to 22.5 ng m^?3, with predominant levels of PAHs appearing in gas phase (～90% of total PAHs). In all samples, the most abundant compounds were phenanthrene, with a contribution to total PAHs between 32 and 44%, followed by naphthalene, fluorene and fluoranthene (contribution range: 10–22%). The levels of total PAHs, expressed as benzo[a]pyrene toxic equivalent factors (BaP_TEF), were lower than 0.06 ng m^?3.     

A review of monitoring of airborne polycyclic aromatic hydrocarbons: An African perspective

In this review, we focus on the status of the monitoring of polycyclic aromatic hydrocarbons (PAHs) in ambient air as well as in living (indoor) and working environments in Africa from 2000 to 2018. This is important as PAHs are ubiquitous in the environment and are known to be potentially carcinogenic. Aspects of sampling such as collection media for particle bound and gaseous PAHs are discussed. The efficiency and basic quality assurance data of commonly employed extraction techniques for separating target PAHs from sampling media using conventional solvent-based and emerging solvent-free approaches were also evaluated. Polyurethane foam and quartz fiber filters are generally the most commonly used collection media for gaseous and particle bound PAHs, respectively. A wide range of total PAH concentrations in ambient air has been reported across the continent of Africa, with the highest levels found at sampling sites close to high density traffic and industrial areas. A rapidly increasing population, commercial and industrial development, poor urban transportation infrastructure and the use of low quality oil products were the main causes of high total gas and particulate PAH concentrations (1.6–103 μg/m³) in West African port cities such as Cotonou, Benin. With regards to indoor environments, gas phase PAHs were detected at the highest total concentrations in rural areas ranging from 1 to 43 μg/m³ in Burundi with naphthalene being the most prevalent. Firewood burning was the major emission source in most developing countries and resulted in benzo[a]pyrene concentrations above the European permissible risk level of 1 ng/m³.     

Solvents and Techniques For The Extraction Of Polynuclear Aromatic Hydrocarbons From Filter Samples Of Diesel Exhaust

Abstract

The amounts of five polynuclear aromatic hydrocarbons-fluoranthene, pyrene, benzo(a)anthracene, benzo(k)fluoranthene, and benzo(a)pyrene-extracted by six solvents with four extraction techniques have been determined for diesel exhaust particulate collected on Teflon-coated glass fiber filters. Samples were analyzed by high pressure liquid chromatography with fluorescence detection. Toluene and methylene chloride gave higher recoveries than methanol, isopropanol, acetonitrile, and acetone for benzo(a)anthracene, benzo(k)fluoranthene, and benzo(a)pyrene. Soxhlet extraction for two hours (approximately 48 cycles) with toluene or acetonitrile was more effective than simple mechanical agitation, ultrasonic agitation for 15 minutes or immersion in refluxing ‘solvent’ for two hours.     

Polycyclic aromatic hydrocarbons (PAHs) in edible oils by gas chromatography coupled with mass spectroscopy

The occurrence of polycyclic aromatic hydrocarbons (PAHs) in nine edible oils of three categories of oil samples, such as soy bean oil, mustard oil and coconut oil, has been studied to determine the contamination degree of this type of oil samples. Eight major carcinogenic polycyclic aromatic hydrocarbons (PAHs), such as naphthalene, anthracene, phenanthrene, fluorene, pyrene, crysene, benzo(a)pyrene and benzo(a)anthracene, were identified and quantified in the extract of edible oils collected from Bangladeshi Markets by gas chromatography and mass spectroscopy. All of the carcinogenic PAHs are not present in the edible oils. A few of the carcinogenic PAHs are present in the oils but it is within the permissible limit. The results for the recoveries of naphthalene, fluorene, phenanthrene, anthracene, pyrene, crysene, benzo(a)anthracene and benzo(a)pyrene were in the range of 56–84%. The limit of detection (LOD) of the GC–MS method, established at signals three times that of the noise for naphthalene, fluorene, phenanthrene, anthracene, pyrene, crysene, benzo(a)anthracene and benzo(a)pyrene, was 2.0–2.5 ng, respectively.     

Methodology for Bioassay-Directed Fractionation Studies of Air Particulate Material and Other Complex Environmental Matrices

Abstract

A normal phase HPLC methodology using a semi-preparative polyaminocyano column in conjunction with a selection of short-term genotoxicity assays has been developed for bioassay-directed fractionation studies of complex environmental mixtures. To illustrate the effectiveness of this methodology, an organic extract prepared from respirable air particulate samples collected in Hamilton, Canada was separated into a non-polar aromatic fraction and a polar aromatic fraction using a combination of alumina and Sephadex LH20 chromatography. These fractions were evaluated for their genotoxic potential using the Salmonella/microsome (Ames) assay with six different strains of Salmonella.

The non-polar aromatic fraction was analyzed by normal phase HPLC and the eluent was collected in one-minute subfractions; these subtractions were bioassayed in three different Salmonella strains (YG1021 -S9, YG1024 -S9 and YG1029 +S9) to afford three different mutation profiles of this sample. Some subfractions which exhibited high mutagenic responses were subjected to further chemical analyses using GC/MS in order to identify those compounds responsible for the genotoxic responses. The nitroarene compounds 2-nitrofluoranthene, 1-nitropyrene and 2-nitropyrene and higher molecular weight polycyclic aromatic hydrocarbons such as benzo[a]pyrene and indeno[l,2,3-cd]pyrene were identified and quantified in some of the biologically active subfractions. The normal phase gradient conditions afforded very reproducible retention times for a series of polycyclic aromatic standards with a broad range of compound polarities. In addition, polycyclic aromatic hydrocarbons (PAH) were observed to elute from the normal phase HPLC column in a series of peaks; successive peaks contained PAH of increasing molecular weight while any individual peak was shown to contain PAH of the same molecular weight.     

A Comparison of Benzo(A)Pyrene-4,5-Epoxide Hydrase Activity in Hamster Embryo Cells,Hepatocytes and Livers Using High-Pressure Liquid Chromatography

Abstract

The benzo(a)pyrene-4,5-epoxide (BP-4,5-epoxide) hydrase activities of intact hamster hepatocytes and embryo cells, and homogenates of these cells as well as of adult liver are compared. The product of the epoxide hydrase (EH) reaction, trans-4,5-dihydro-4,5-dihydroxybenzo(a)pyrene (BP-4,5-diol), was isolated by high-pressure liquid chromatography (HPLC) with a Waters Bondapak C₁₈/Corasil column and acetonitrile-water as the mobile phase. Using this procedure to determine BP-4,5-epoxide hydrase activity in intact cells, it was found that 266 nmoles of BP-4,5-diol/10⁶ cells were produced by hepatocytes while no diol formation was detected with embryo cells. EH activity in the intact hepatocytes was 8-fold greater than in hepatocyte homogenates.     

Differentiation of polycyclic aromatic hydrocarbons using electron capture negative chemical ionization

A number of isomeric polycyclic aromatic hydrocarbons may be distinguished using electron capture negative chemical ionization when methane is used as a buffer gas, including benzo[a]pyrene and benzo[e]pyrene. The ionization behavior of these compounds may be predicted, on the basis of their electron afinities, allowing compounds to be distinguished without the use of standards.     

Detection of Benzo[a]pyrene in Fried Food by Ultrasound-Assisted Matrix Solid-Phase Dispersion and Isotope Dilution GC–MS

A simple, sensitive and reliable analytical method was developed for the detection of benzo[a]pyrene in fried food using gas chromatography-mass spectrometry with an isotope-labelled internal standard. Samples were directly extracted and purified by the ultrasound-assisted matrix solid-phase dispersion (MSPD) procedure. The simple pretreatment procedures were tested with different absorbents (C18, NH₂, Oasis, and SiO₂). The optimal ultrasonication-assisted MSPD was achieved by MSPD-SiO₂ and sonication for 10 min in an ultrasonic bath. The samples were quantified using benzo[a]pyrene-d₁₂ as the internal standard. An analysis of the samples spiked with different levels of benzo[a]pyrene showed recoveries ranging from 84.6 to 103.2 %, with an RSD of 3.21–8.32 %, depending on the spiking level. This method was thus shown to be suitable for the detection of benzo[a]pyrene in fried food.     

Custom-Made C18 Column for Simultaneous Determination of Endocrine Disrupting Substances in Water by Diode-Array and Fluorescence Detectors

A C₁₈ stationary phase was synthesized for a custom-made HPLC column. When compared to a commercial C₁₈ column, better chromatographic performances were obtained. This column was successfully applied for simultaneous determination of p,p′-DDT, o,p′-DDT, benzo(a)anthracene, benzo(b)fluoranthene, and benzo(a)pyrene in waters by high performance liquid chromatography coupled with dual detectors (diode array and fluorescence detectors) combined with solid phase extraction. Low method detection limits were obtained, i.e., p,p′-DDT: 0.5 µg L^?1, o,p′-DDT: 1 µg L^?1, benzo(a)anthracene: 2.5 ng L^?1, benzo(b)fluoranthene: 5 ng L^?1, and benzo(a)pyrene: 2.5 ng L^?1. High recoveries that ranged from 82 to 94% were obtained for all compounds.     

The Importance of Long and Short-Term Air-Soil Exchanges of Organic Contaminants

Abstract

Retrospective analysis of archived soil samples collected and stored from long-term agricultural experiments in the UK has shown how soil organic chemical composition has changed over time. High molecular weight polycyclic aromatic hydrocarbons (e.g. benzo[a]pyrene) and polychlorinated dibenzo-p-dioxins and -furans have increased in concentration through this century as a result of cumulative atmospheric depositional inputs. Concentrations of polychlorinated biphenyls and low molecular weight hydrocarbons (e.g. phenanthrene) peaked in the late 1960s/early 1970s, but have declined subsequently. This reflects declining atmospheric inputs of these compounds and losses from surface soils by volatilisation back to the atmosphere and biodegradation. PCBs and low molecular weight PAHs exist predominantly in the vapour phase in air, whilst heavy PAHs and PCDD/Fs are predominantly particulate-bound. Outgassing from soils is probably the most important contemporary source of PCBs to the atmosphere in the UK. Future UK PCB air concentrations will presumably therefore be influenced (controlled) by the rate of desorption and outgassing, as soil and air concentrations move towards a condition of equilibrium partitioning. Archived soils collected and stored before the commercial manufacture of PCBs contain no PCBs indicating that there is no ‘natural production’ of these compounds. However, within a few hours of exposure to contemporary air these samples contain detectable quantities of PCBs. Short-term air-soil exchange, such as during soil drying in the laboratory, can lead to contamination of samples which contain low concentrations of PCBs and loss from samples which contain high concentrations.     

Detection of Benzo[a]pyrene in Fried Food by Ultrasound-Assisted Matrix Solid-Phase Dispersion and Isotope Dilution GC–MS

A simple, sensitive and reliable analytical method was developed for the detection of benzo[a]pyrene in fried food using gas chromatography-mass spectrometry with an isotope-labelled internal standard. Samples were directly extracted and purified by the ultrasound-assisted matrix solid-phase dispersion (MSPD) procedure. The simple pretreatment procedures were tested with different absorbents (C18, NH₂, Oasis, and SiO₂). The optimal ultrasonication-assisted MSPD was achieved by MSPD-SiO₂ and sonication for 10 min in an ultrasonic bath. The samples were quantified using benzo[a]pyrene-d₁₂ as the internal standard. An analysis of the samples spiked with different levels of benzo[a]pyrene showed recoveries ranging from 84.6 to 103.2 %, with an RSD of 3.21–8.32 %, depending on the spiking level. This method was thus shown to be suitable for the detection of benzo[a]pyrene in fried food.

     

Aliphatic and Aromatic Hydrocarbons in the Mediterranean Aerosol

Abstract

The atmospheric transport of organic pollutants over long distances and their effect on the biological cycles of the sea are two major questions of concern in environmental chemistry. These processes are of particular importance in the Mediterranean Sea because of its semi-enclosed characteristics, which determine the accumulation of the pollutants entering into the system.

In order to get some insight into these processes a project (PHYCEMED), was developed for the evaluation of the atmospheric budget of organic and inorganic substances in the Western Mediterranean and for the investigation of the exchange mechanisms of these materials across the air/sea interface.

A high volume air sampling system including a cascade impactor was placed on board of the R/V le Suroit for collecting the acrosols along several transects parallel to the French, Spanish and North-African coasts, facing areas of different population densities and industrial activities. The cruise was realised on October 1983 and the particulate material was fractionated into the following sizes: 7.2, 3.0, 1.5, 0.96, and 0.03 μm. Quantitative and qualitative analyses of the aliphatic and the aromatic hydrocarbons present in these fractions were performed by high resolution gas chromatography and gas chromatography-mass spectrometry.

Total non-aromatic hydrocarbon concentrations are in the range 30-57 ng/m³ (10-14ng/m³ for n-alkanes). The distribution of n-alkanes indicates that most of the aerosol mass is associated with small particles < 1 μm.Polycyclic aromatic hydrocarbons are identified from phenanthrene to benzo(ghi)perylene with fluoranthene and pyrene as dominant compounds. Concentrations for individual PAH vary in the range 4.1 pg/m³ for benzo(a)anthracene up to 100 pg/m³ for fluoranthene. The evaluation of different contributions such as land plant waxes or soil sources and various anthropogenic sources is discussed from n-alkanes and PAH distribution patterns.     

Microheterogeneity evaluation of polycyclic aromatic hydrocarbons in particulate standard reference materials

With the emergence of highly sensitive analytical techniques, the microanalysis of natural-matrix materials employing smaller sample sizes is increasingly more common, which subsequently warrants a homogeneity assessment for the individual components at the appropriate sampling level. Pressurized liquid extraction (PLE) in combination with gas chromatography/mass spectrometry (GC/MS) has been used to determine the sampling constants and evaluate the relative homogeneity of trace levels of polycyclic aromatic hydrocarbons (PAHs) for two previously certified particulate standard reference materials, SRM 1649a Urban Dust and SRM 1650b Diesel Particulate Matter, in the milligram sampling range. Fluoranthene, pyrene, benz[a]anthracene and benzo[e]pyrene within SRM 1650b Diesel Particulate Matter were deemed to be homogeneous, based on relatively small sampling constants (K _S<100 mg), whereas the larger sampling constants (K _S>100 mg) obtained for all PAHs in SRM 1649a Urban Dust suggest more material heterogeneity. The material heterogeneity of ten individual PAHs (phenanthrene, anthracene, fluoranthene, pyrene, benz[a]anthracene, benzo[k]fluoranthene, benzo[e]pyrene, benzo[a]pyrene, indeno[1,2,3-cd]pyrene and benzo[ghi]perylene) was also described via nonlinear relationships (i.e., power law) between subsampling error S _s (%) and sample mass, which are used to predict analyte-specific minimum sample masses that result in a specific level of analytical uncertainty. Electronic supplementary material Supplementary material is available for this article at and is accessible for authorized users.     

Solid‐phase microextraction with gas chromatography and mass spectrometry determination of benzo(a)pyrene in microcrystalline waxes used as food additives

Microcrystalline waxes are mixtures of solid, saturated hydrocarbons mainly branched and characterized by a carbon number over C₆₀. They are used as food additives for the surface treatment of confectionery and some fruit varieties, in chewing gum base, protective coatings, defoaming agents, and surface finishing agents. Commission Regulation No 231/2012 established physical and chemical specifications for microcrystalline waxes to use in food, and posed a limit of 50 μg/kg for benzo(a)pyrene. Due to the low solubility of microcrystalline waxes in organic solvents and matrix interferences, analytical determination of benzo(a)pyrene represents a difficult task. The official method for indirect determination of total polycyclic aromatic hydrocarbons uses unspecific spectrophotometric detection and a quite laborious, time‐ and solvent‐consuming extraction method. A liquid–liquid partition method followed by solid‐phase microextraction was developed to isolate benzo(a)pyrene from the bulk of saturated hydrocarbons in microcrystalline waxes, with the aim to have a simple and effective method to verify compliance with the legal limit. The final determination was carried out by gas chromatography coupled to mass spectrometry. Good linearity was obtained, along with a recovery of about 80% from the liquid–liquid partitions. The repeatability of the entire method was <6% and accuracy was <3%.