Determination of Benzoylmetronidazole in Suspension Formulations by Differential Pulse Polarography

Abstract

A rapid, reproducible and accurate method for the determination of benzoylmetronidazole in pharmaceutical suspensions is presented. Differential pulse polarography at a static mercury drop electrode is used for the reduction of the nitro group of benzoylmetronidazole.     

一阶导数差示脉冲极谱法用于扑热息痛的定量分析

一阶导数差示脉冲极谱法用于扑热息痛及其制剂的定量分析，在乙醇－水－２．０×１０＾－＾３ｍｏｌ／ＬＨ２ＳＯ４（１２．５：１１．５：１）的溶液中，于０．２４Ｖ（ｕｓＡｇ／ＡｇＣｌ）处出现良好的一阶导数差示脉冲极谱峰，在３．３×１０＾－＾４～３．３×１０＾－＾３ｍｏｌ／Ｌ范围内，浓度与其一阶导数差示脉冲极谱峰值呈线性关系，检测限为７．８×１０＾－＾８ｍｏｌ／Ｌ。方法简便，快速，灵敏，结果准确。     

Determination of Entacapone by Differential Pulse Polarography in Pharmaceutical Formulation

Abstract

The electrochemical methods, sampled direct current, and differential pulse polarography, were developed successfully and applied to the routine determination of Entacapone in pharmaceutical formulation. Both methods gave rise to three reduction waves or peaks respectively. The irreversibility and the diffusion‐controlled of the first reduction were confirmed by cyclic voltammetry. The limiting currents are directly proportional to the concentration of entacapone with a correlation coefficient of 0.99. The within‐day coefficients of variation and the day‐to‐day coefficient of variation were less than 3.5% for entacapone and Comtan^®. The percentage recovery for entacapone in tablets is satisfactory for both methods. The method is simple without any pretreatment.     

定量测定秦皮中秦皮甲素的二阶导数示差脉冲极谱法

建立了中草药秦皮中秦皮甲素的二阶导数示差脉冲极谱定量分析方法。秦皮甲素在乙醇－2mol/L氯化锂－水（体积比2：1：5）的底液中,于－1．703V（vs Ag/AgCl)处出现一良好的二阶导数示差脉冲极谱峰,其峰幅值与秦皮甲素在0．2－1．6mmol/L范围内呈非常显著的线性关系（P＜0．01）,检测下限脒50mmol/L。该法简便、快速、灵敏,结果准确。     

微分脉冲极谱同时测定三种碱性氨基酸的研究

应用微分脉冲极谱，在ｐＨ９．０ ＮａＢ４Ｏ７－ ＣＨ３ＣＨＯ－Ｃｏ２＋－ ＮａＯＨ组成的极谱底液，扫描电位－ ０．８０～－ １．６０ Ｖ、振幅 ２０ｍＶ、扫描速度５ｍＶ／ｓ、一滴汞周期２ｓ的条件下进行连续扫描测量三种碱性氨基酸，获得三个灵敏 度和分辨率均较高的极谱峰图。该法简便快速，稳定可靠，为测量各种蛋白质中的三种磁性氨基酸提供一种新途 径。     

磺胺甲恶唑的二阶导数差示脉冲极谱法测定

建立了磺胺甲恶唑的二阶导数差示脉冲极谱定量分析方法,磺胺甲恶唑在１０％ＨＣｌ－（硼酸－氯化钾缓冲溶液）－水（５：５：９０）的底液中,于－１．４５Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）处出现一良好的二阶导数差示脉冲极谱峰,磺胺甲恶唑浓度与其峰高在０．０８～０．８０ｍｍｏｌ／Ｌ范围内呈线性关系（ｐ〈０．０１）,检测限为８．６ｎｍｏｌ／Ｌ。本法简便、快速、灵敏、结果准确。     

The Determination of Nitrite and Nitrate Ions by Differential Pulse Polarography

Abstract

A previously reported method for the determination of nitrite ion has been extended to include nitrate ion. Nitrate is reduced to nitrite by a cadmium column and the nitrite ion determined as diphenylnitrosamine. Cadmium interference is removed by pH adjustment and the use of KDTA.     

两种蒙药中锗的差示脉冲极谱测定及其红外光谱的差异

采用差示脉冲极谱法,以3,4-二羟基苯甲醛的0.072 mol·L-1硫酸溶液作为底液,在峰电位为-0.53 Ⅴ(vs．Ag/AgCl),锗(Ⅳ)浓度在1.03×10-5～1004×10-4mol·L-1范围内与峰电流呈线性关系.据此测定了阿嘎日-35和阿嘎日-8中总锗、无机锗、有机锗含量,并利用红外光谱比较了两种蒙药的红外谱图的差异,据此可对两种蒙药予以区别.     

一阶导数差示脉冲极谱法用于甲硝唑的定量研究

本实验运用一阶导数差示脉冲极谱法对甲硝唑及其制剂进行了定量研究。在０．００１ｍｏｌ／Ｌ氯化钾－０．００１ｍｏｌ／Ｌ盐酸－水（１＋０．２＋４８）的底液中，甲硝唑于－０．８００Ｖ（ｖｓ Ａｇ／ＡｇＣｌ）处出现一良好的一阶导数差示脉冲极谱峰，在５０～３００μｇ／ｍＬ范围内，药物浓度与其导数峰幅值呈线关系，检测限为８．０×１０＾－８ｍｏｌ／Ｌ。本法操作简便，快速，灵敏，结果准确。     

Indirect Determination of Trace Tetraborate by Differential Pulse Polarography Using Its Copper Complex and Application to Waste and Drinking Water

A new differential pulse polarographic (DPP) method has been developed for the trace determination of boron. Its most stable copper complex is used in 0.5 M KNO₃ electrolyte since boron is not electroactive. By continuous addition of tetraborate to copper solution, the copper peak decreased first but then the peak became very small and nearly constant. This point was used for the boron determination. It was found that one mole of copper used two moles of tetraborate. Using this relationship, 1×10^?5 M tetraborate could be determined. The quantification limit was 2.5×10^?6 M and detection limit was 8×10^?7 M. In the presence of complex forming ions such as Pb, Zn, and Cd, the borate found in sample was somewhat smaller because of their reaction with borate. But since their complexes were not as strong as copper, only a few percent of borate were used. No interference was observed in the presence of calcium, chloride and sulfate. This method is applied for the determination of B in borax ore, waste water of borax industries and tap water of Ankara city.     

磺胺二甲嘧啶钠的二阶导数差示脉冲极谱法定量研究

建立了磺酸二甲嘧啶钠的二阶导数差示脉冲极谱定量分析方法,磺胺二甲嘧啶钠在乙醇－（硼酸－氯化钾缓冲液）－水（体积比７０：２：２８）的底液中,于－１．５６０Ｖ（ｖｓ．Ａｇ／ＡｇＣｌ）处出现一良好的二阶导数差示脉冲极谱峰,磺胺二甲嘧啶钠浓度与其峰幅值在０．０６～０．６ｍｍｏｌ．Ｌ＾－１范围内呈非常显著的线性关系（Ｐ〈０．０１）,检出限为９．２ｎｍｏｌ．Ｌ＾－１,已用于注射液中磺酸二甲嘧啶钠的测定。     

Components of the Net Current in Differential Pulse Polarography

As the modern (voltammetric) software packages offer ‘resolution’ of each individual net signal in differential pulse polarography (DPP) to its components, an attempt was made to test such a possibility on several model systems. Reversible and nonreversible reduction processes of simple metal ions (Cd²⁺, Eu³⁺) were included, together with some examples of the anion induced adsorption (Cd²⁺‐I^? and Pb²⁺‐Br^? systems) under conditions of partly or fully covered electrode surface. Taking into account that so called ‘backward’ current is in fact DC wave, it could be said that one technique is hidden within the other. Consequently, DPP measurements together with following of the ‘backward’ signals could give more information and save the time. ‘Forward’ component offers additional possibilities in data treatment, especially when its relationship to the ‘backward’ current (with respect to the potential and height) is taken into account. Such an approach seems promising, even when applied on a purely qualitative level, because some effects which cannot be observed if only the net signals are followed become obvious when their components are taken into consideration.     

Voltammertric Behaviour of Clonixin and its Differential Pulse Polarographic Determination in Tablets

ABSTRACT

Clonixin, a non-steroid analgesic, can be both reduced at the mercury electrode and oxidised at the glassy carbon electrode. The anodic response shows well-defined waves in a pH range between pH 2-12. The polarographic response shows two irreversible waves or peaks in the range between pH 1-6 shifting cathodically when pH increases. Above pH 7.0 all the signals disappeared. The first signal in the dpp mode at pH 1.8 was selected for analytical use. The polarographic     

Simultaneous Trace Determination of Nickel and Cobalt in Natural Waters by Differential Pulse Polarography

Abstract

A differential pulse polarographic method has been developed for the simultaneous low level determination of nickel and cobalt in the presence of furildioxime in natural waters. The nature of the electrode processes was studied with cyclic voltammetry. Limits of determination of 0.4 μg/L and 0.15 μg/L were achieved for nickel and cobalt respectively     

维生素C及其制剂的一阶导数差示脉冲极谱法测定

本文建立了维生素Ｃ及其制剂的一阶导数差示脉冲极谱定量分析方法，在水溶液中，维生素Ｃ于－１．１０Ｖ（ｖｓＡｇ／ＡｇＣｌ）处出现一良好的一阶导数差示脉冲极谱峰，在１～１７５μｇ／ｍＬ范围内，维生素Ｃ浓度与其一阶导数差示脉冲极谱峰幅值呈非常显著的线性关系（Ｐ〈０．０１），方法简便，快速，灵敏，结果准确。     

Determination of Chloramphenicol (CAP) in Food Products by Differential Pulse Polarography

ABSTRACT

The electrochemical determination of chloramphenicol (CAP) in food using mini- and micro- mercury drop electrodes and differential pulse polarography (DPP) has been elaborated. A phosphate buffer with pH 6.6 was used as the basic electrolyte. The analysis was based on a peak at the potential E_p = ?0.320 V which showed a clearly linear dependence of the peak current on the concentration of chloramphenicol in the sample under investigation. Prior to the determination of chloramphenicol in actual samples it was necessary to extract this antibiotic with organic solvents such as methanol, ethanol and ethyl acetate.

In order to separate CAP in its basic form, various modifications of sample preparation procedures were made for the analysis with the use of selected hydrolytic enzymes. The determined quantities of CAP in the samples of meat, milk, eggs and their products ranged in the ng/g d.w. range.

For purposes of comparison and verification of the electrochemical results of CAP determination, chloramphenicol was determined in the same samples, by the immunoenzymatic method ELISA.     

Application of Net Analyte Signal Standard Addition Method (NASSAM) for Simultaneous Determination of Lead and Tin by Differential Pulse Polarography

Differential pulse polarography was used for simultaneous determination of Sn²⁺ and Pb²⁺. But there is a problem for simultaneous determination and it is high overlapped DPPs of mentioned cations that their determination is impossible in the presence of each other, so multivariate calibration methods as chemomatrics methods were used for this determination. There are some disadvantageous for multivariate calibration methods that can be solved by a new and simple method called net analyte signal standard addition method. This method has some advantages, such as: the use of a full voltammogram, realization in a single step, therefore it does not require calibration and prediction steps and only a few measurements are required for the determination.     

Components of the Net Current in Differential Pulse Polarography. Part 2. Kinetics and Adsorption

Components of the net response in differential pulse polarography were studied theoretically, assuming gradually changing electrode rate constant or strength of the reactant adsorption. The difference between the maximum potential of the peak component and the half‐wave potential of the wave component appear as an important parameter. From its value, the electrode rate constant can be calculated even when the standard potential is not known. In a reversible process, effects of the reactant adsorption on the mentioned separation are less pronounced. The results were compared with experimentally obtained effects. For deeper insight into the applicability of this approach, additional experimentally obtained polarograms (that reflect different potential/timing parameters or changing character of the electrode process) should be studied in terms of their components.     

Determination of Traces of Copper,Lead, and Cadmium in Cobalt by Derivative Pulse Polarography

Abstract

A derivative pulse polarographic method is described for determining traces of copper, lead and cadmium in cobalt and its compounds without separation. In hydrochloric acid medium the detection limits are respectively about 0.02, 0.04 and 0.1 ppm in metallic cobalt when analysing 2 M cobalt solutions. The procedure was applied to the analyses of synthetic and commercially available cobalt samples and showed a satisfactory sensitivity and precision at various concentrations levels of the three impurities.