Flow-injection spectrophotometric determination of cobalt by extraction as tetrathiocyanatocobaltate(II) with the ethylenebis(triphenylphosphoniu) cation

Cobalt (0–10 μg) may be determined spectrophotometrically at 625 nm after flow-injection extraction into chloroform of the ion associate ethylenebis(triphenylphosphonium) tetrathiocyanatocobaltate(II). The carrier stream contained 10% (w/v) ammonium fluoride and the reagent stream contained 0.5% (w/v) ethylenebis (triphenylphosphonium) bromide and 5% (w/v) ammonium thiocyanate. The injection rate was 20 h^?1. The calibration graph is linear up to 20 μg ml^?1 and detection limit is 0.23 μg ml^?1 cobalt, based on injection volumes of 500 μl. The system has been applied to the determination of cobalt in a range of tool steels.     

Determination of Traces of Mercury (II) and Phenylmercury by Direct Polyurethane foam Thin-Layer Spectrophotometry

Abstract

The determination of mercury and phenylmercury in the ppb concentration range using polyurethane foam (PUF) thin-layer spectrophotometry has been described. Sorption of mercury and phenylmercury into foam parallepiped loaded with diphenylthiocarbazone (dithizone) contributed to considerable improvement in the absorbance value of the colored species, being concentrated about 140 times.

The method allowed the achievement of satisfactory results, the detection limits are 5 and 10 μg per litre for mercury and phenylmercury, respectively, for 100ml sample volume. The average recovery from tap water amounts to 100% for mercury and 96.6% for phenylmercury.     

Spectrophotometric Determination of Nickel(II) with O-hydroxyhydroquinonephthalein in the Mixed Micellar Media of Zephiramine and Tween 20

Abstract

The effect of mixed surfactants on the color reaction between nickel(II) and o-hydroxyhydroquinonephthalein(Qnph) was examined in weakly basic media. The color development of the metal complex in the presence of cationic and nonionic surfactants (mixed micellar media of Zephiramine (Zp) and Tween 20) was very stable and exhibited a high and reproducible absorbance. The calibration curve was linear in the ranges of 0 – 7.0 μg nickel(I1) in a final volume of 10 ml at 545 or 536 nm. The method developed does not require an organic solvent extraction step. The apparent molar absorptivity and Sandell sensitivity were 1.26 × 10⁵ 1 per mol per crn and 0.0045 μg per cmL nickel(II), respectively, at 545 nm.     

Tetradecyldimethylbenzylammonium thiocyanate adsorbent supported on naphthalene for the preconcentration and determination of cobalt in aluminium alloys and steels using atomic absorption spectrometry

A solid ion-pair material produced from tetradecyldimethylbenzylammonium chloride (TDBA) and ammonium thiocyanate on naphthalene provides a simple, rapid and selective technique of preconcentrating cobalt from up to 200 ml of aqueous solution. Cobalt reacts with sodium 1-nitroso-2-naphthol-3,6-disulphonate (nitroso-R salt) to form a brown, water-soluble chelate anion. The chelate anion forms a water-insoluble Co-nitroso-R salt-TDBA complex on naphthalene packed in a column and trace cobalt is quantitatively retained on the naphthalene in the pH range 2.7–11.0 at a flow-rate of 2 ml min^?1. The solid mass is stripped from the column with 5 ml of dimethylformamide (DMF) and cobalt is measured by atomic absorption spectrometry (AAS) at 241 nm. The calibration graph is linear over the concentration range 0.5–15μg Co in 5 ml of dimethylformamide solution. Seven replicate determinations of 9 μg of cobalt gave a mean absorbance of 0.095 with a relative standard deviation of 1.7%. The sensitivity for 1% absorption was 0.0834μg ml^?1 (0.240 μg ml^?1 for direct AAS on the aqueous solution). The proposed method was utilized for the determination of cobalt in standard aluminium alloys and steel samples.     

Extractive Spectrophotometric Determination of Chlorprothixene Hydrochloride

ABSTRACT

A simple, rapid and accurate method for determination of chlorprothixene hydrochloride is presented. It is based on the liability of the chlorprothixene tertiary amine group nitrogen atom to form ion pair complexes with niobium (V) thiocyanate complex. The formed compound is insoluble in water but well soluble in some organic solvents. The reaction is followed spectrophotometrically by measuring the absorbance at λ= 362 nm. This property has been successfully used for the extractive spectrophotometric determination of chlorprothixene. Beer's law was obeyed in the range 9- 50 μg/ml of chlorprothixene hydrochloride. The method is suitable to the determination of analyte in commercial products. The results were compared with those obtained by the official procedure.     

Spectropotometric Determination of Cyanide by Flow Injection Analysis

Abstract

The flow injection technique is shown to provide fast, reliable, and sensitive determination of cyanide. Spectrophotometric detection in the ultraviolet region at 267 nm was used for measuring the absorbance of tetracyanonickelate (II) complex ion. The nickel carrier stream and the sample solutions were buffered at pH 10 (ammoniacal buffer). The method has a detection limit of 0.2 ppm cyanide. At a sampling rate of 90 samples per hour, with 60 μl sample injections, high reproducibility of measurements was achieved, with about 1% relative standard deviation. The effects of sample volume, flow rate, coil length, and anions interference on the FIA-spectrophotometeric signals are reported.     

Spectral Investigation on Ruthenium(III)-allyl Thiourea System

Abstract

Ruthenium(III) forms a 1:2 complex with allyl thiourea. Conformity to Beer's law was observed for up to 12 pg/ml of ruthenium, in acidic medium.

The molar absorptivity of the complex is 1.66E+04 1 mol^?1 cm^?1, at 270 nm; the Sandell's sensitivity of the reaction for ruthenium is 0.0061 μg cm^?2 per 0.001 absorbance unit.

The tolerance to diverse ions is quite satisfactory.

The infrared spectra of allyl thiourea and of its ruthenium complex, recorded in the 2.5 - 50 μ region, reveal that only sulphur-to-ruthenium bonds are present in the complex.

A comparison with the main, most recent, spectrophotometric reagents for ruthenium is reported. The present method has the advantages of simplicity and reasonable sensitivity.     

Determination of Traces Of Bismuth in Water with Polyurethane Foak Thin-Layer Spectrophotometry

Abstract

A method for the spectrophotometric determination of bismuth is described. The method is based on using polyether polyurethane foam sorbent as a favourable matrix. Sorption of the bismuth iodide complex into the foam thin layer contributed into substantial improvement of the measured absorbance value of the coloured species. In this way quite satisfactory results were achieved, the average recovery amounts to 105.25%.     

Colorimetric Analysis of the Acrosin Inhibitor Para-Aminobenzamidine

Abstract

A method is presented for the colorimetric assay of para-aminobenzamidine (PAB) in blood. Essentially, the PAB in trichloroacetic acid extracts is coupled to N-(l-napthyl)ethylenediamine in a typical diazotization reaction. The colored complex formed exhibits a peak absorption at 540 nm. This complex in distilled water is very stable and loses less than 5% of its absorptivity over a 24 hour period. Trichloroacetic acid extracts of whole blood containing PAB are likewise stable, exhibiting less than a 7% mean reduction in absorbance after standing for 24 hours. A plot of optical density versus concentration of the PAB diazo complex over a range of 1–20 μg/ml shows excellent linerarity. The method can accurately quantitate as little as 1 μg/ml at a dilution of 3.5.     

Column Chromatographic Preconcentration of Copper in Alloys and Complex Materials Using 9,10 Phenanthrenequinone Monoxime Supported on Naphthalene

Abstract

A solid chelating compound phenanthrenequinone monoxime PQM) supported on naphthalene provides a rapid and economical means of preconcentration and separation of copper from the aqueous samples. Copper forms a complex with PC:: supported on naphthalene in the column at pH 6.1–8.4 with a flow rate of 1 ml/min. The metal complex and naphthalene are dissolved out from the column with 5 ml of DMF and the absorbance is measured at 470 nm against reacent blank. Beer's law is obeyed in the concentration range 0.6 9.6 μg of copper in 5 ml of DMF. The molar absorptivity and sensitivity are 6.3×10⁴ L mol^?1 cm^?1 and 0.001 μg cm^?2 respectively.     

N-p-tolyl-2-furohydroxamic Acid as the Extracting and Spectrophotometric Reagent for Vanadium(V)

Abstract

A simple and rapid spectrophotometric determination of vanadium(V) is described. The vanadium-N-p-tolyl-2-furohydroxamic acid complex is extracted into chloroform form 6–8 molar hydrochloric acid solution. Maximum absorbance occurs at 540 nm and Beer's Law is obeyed over the range of 0–15 μg of vanadium in the organic phase. The molar absorptivity is 3.0 × 10³ mole^?1 cm^?1 at 540 nm.

Vanadium could be determined in high purity niobium and tantalum metals, cast iron, steel, non ferrous alloys and silicates. Vanadium could be determined in the presence of several commonly occurring cations.     

Selective Kinetic Spectrophotometric Determination of Nitrite in Food and Water

Abstract

A highly selective and sensitive method for the kinetic spectrophothometric determination of sub-microgram amounts of nitrite has been development based on its reaction with Nile blue 2B in acidic medium. The reaction is monitored spectrophotometrically at 595 nm at a fixed time of 4.5 min. The change in absorbance at 595 nm is related to the concentration of nitrite in the range 0.005 - 1.100 μg.ml^?1 The detection limit is 0.001 μg.ml^?1. The relation standard deviation is 1% for 0.020 μg.ml^?1 of nitrite for ten replicate measurements. Most common anions and cations do not interfere. The procedure was applied to the determination of trace amounts of nitrite in sausage and water.     

Column Preconcentration of Palladium Using Phenanthrenequinonedioxime Supported on Naphthalene by Atomic Absorption Spectroscopy

Abstract

A solid chelating compound, phenanthrenequinonedioxime(PQDO) supported on naphthalene provides a rapid and economical means of preconcentration of palladium from the aqueous samples. Palladium forms a complex with PQDO supported on naphthalene in the column at pH 1.2～2.7. The metal complex and naphthalene are dissolved out from the column with 5 ml of dimethylformamide-nitric acid (100+4) and the absorbance is measured atomic absorption spectrometer at 244.7 nm. A calibration curve is linear over the concentration range 1～24 μg of palladium in 5 ml of the final solution. The sensitivity for 1% absorption is 0.126 μg/ml (0.153 μg/ml for the direct AAS method from the aqueous medium). The method has been used for the determination of palladium in various synthetic samples and can be safely applied to the environmental samples too.     

Determination of Folic Acid in Commercial Diets by Anion-Exchange Solid-Phase Extraction and Subsequent Reversed-Phase HPLC

Abstract

Folic acid at the μ/g level is determined in total nutritional diets by concentration on disposable commercial anion exchange columns followed by elution with a concentrated salt solution and subsequent reversed-phase HPLC with absorbance detection at 365 nm. The method is specific for folic acid with respect to some known degradants and electrochemically generated oxidation products.     

Revised Method for Determination of Aspirin and Salicylic Acid in Human Plasma by High Pressure Liquid Chromatography

Abstract

The method for the analysis of aspirin and salicylic acid in human plasma has been updated to include advances in column technology, extraction procedures and absorbance detection. Aspirin and salicylic acid are extracted from acidified plasma into an organic solvent system containing internal standard. Following controlled evaporation under partial vacuum of the organic extract, the dried down-residue is reconstituted with mobile phase. Chromatography is ion suppression reverse phase on a 5 μm O.D.S. column with detection by absorbance at 237 nm and optional fluorescence. Concentration of aspirin as low as 0.20 μg/ml and salicyclic acid as low as 0.50 μg/ml can be quantitated.     

Semiquantitative and Quantitative Determination of Trace Amount of Phosphate Ion in Water Using Polyurethane Foam Thin -Layer Colorimetry

Abstract

A simple, sensitive and fast method for the colorimetric determination of phosphate ion in water is described.

The method is based on spectrophotometric measurement of the blue molybdoantimony phosphoric acid species sorbed in a polyurethane foam thin-layer for quantitative determination of phosphate ion, or the visual color comparison technique for rapid semiquantitative determination.

The detection limit for the quantitative procedure is 5 μg/1 and for semiquantitative procedure 20 μg/1 for sample volumes of 100 ml and 25 ml, respectively.     

Flow Injection Analysis of Famotidine with Spectrophotometric Detection

Abstract

A flow injection determination of famotidine has been described. The method is based on the reaction of the drug with cupric acetate to form a blue coloured complex which shows absorption maxima at 314 nm and 630 nm. For an injection volume of 100 μl calibration graphs were rectilinear from 10- 50 μg. ml^?1 and 50–500 μg.ml^?1 of drug at the two wavelengths respectively. Samples could be analysed at rates upto 60 per hour with a relative standard deviation less than 1.4%. The method was evaluated by analysis of the pure drug and commercial formulations. The results compare well with those obtained by official methods.     

A New Spectrophotometric Method for Determination of Vitamin B12 as Cobalts

Abstract

A spectrophotometric method for determination of Vitamin B₁₂ (Cyanocobalamin) as cobalt in pharmaceutical preparations is described. The sample is first decomposed by concentrated sulfuric and nitric acids and the dry residue is solubilized in distilled water. The cobalt present is then spectrophotometrically determined at Λ= 317 nm as Co-HMPA-SCN complex. The complex is stable for a long time in the range of pH 3–10. The presence of many other metal cations does not interfere.     

Simultaneous Determination of Micro Bromide and Iodide by Kinetic Spectrophotometric Method

ABSTRACT

ABSTRACTA new kinetic spectrophotometric method for the simultaneous determination of concentrations of micro bromide and iodide has been proposed. It is based on their catalytic effects on the reaction of m-cresol purple oxidized by potassium periodate in hydrochloride acid medium. The reaction rate was monitored by measuring the decrease in absorbance at 528nm and the increase in absorbance at 455nm. The total difference in absorbance of the sum of bromide and iodide is identical with determination of bromide was carried out after Cr(VI) oxidized I? to I₂, and I₂ was removed by extraction with CCI₄, and the amount of iodide was measured by subtracting the absorbance change of bromide from the total absorbance change in the presence of bromine and iodide. The optimum conditions influencing the reaction rate were studied. The linear range of determination is 0～4.0μg/ml for Br? and 0～3.0 μg/ml for I?. The detection limits are 0.032μg/ml for Br? and 0.059 μ/ml for I?. The method was successfully applied to the determination of micro amounts of bromide and iodide in food and life samples.     

Kinetic Spectrophotometric Determination of Acetaldehyde

ABSTRACT

A method for determination of trace quantities of acetaldehyde based on its inhibition effect on the malachite green-sulfite reaction is described. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance at 613 nm by a fixed time method of 60 seconds. The method allows the determination of acetaldehyde in the range of 0.2-10 μg/ml. The limit of detection was 0.1 μg/ml and the relative standard deviation for ten determinations of 2 μg/ml acetaldehyde was 1.8%. The method is applied to the determination of acetaldehyde in chemical industrial waste water with satisfactory results.