Determination of Tetracyclines by Solid-Phase Extraction with a Molecularly Imprinted Polymer and High-Performance Liquid Chromatography

Tetracyclines are widely used antibiotics classified as emerging pollutants and may lead to an increase in bacterial resistance in the environment. In order to determine these compounds at low concentrations, a water-compatible molecularly imprinted polymer was developed for solid-phase extraction followed by high-performance liquid chromatography analysis. The monomers 2-hydroxyethyl methacrylate and glycerol dimethacrylate were added 1 h after the start of the synthesis to provide hydroxyl groups on the polymer surface. This hydrophilic layer established hydrogen bonds with water, minimizing interferences of this solvent in the analyte-polymer complex, increasing analyte adsorption. The polymer was then used for solid-phase extraction to preconcentrate the tetracyclines. The method provided low limits of quantification (5 µg L^?1), good linearity, precision, and accuracy for tetracyclines, with preconcentration factors of 14, 19, 29, and 41 for oxytetracycline, tetracycline, chlortetracycline, and doxycycline, respectively.     

Flow Injection Chemiluminescence Determination Of Tetracyclines

Abstract

A fast and simple flow injection chemiluminescence method for the determination of trace amounts of tetracyclines is proposed based on the chemiluminescence of the KMnO₄ - TCs redox reaction in acidic medium in the presence of a sensitizer, OP. The response to the concentration of tetracyclines is linear in the range of 1.00 to 1000 μg mL^?1 with a relative standard deviation < 2.3 % for determination of 50.0 μg mL^?1 of each antibiotic (n = 11). The detection limits for tetracycline, oxytetracycline and chlortetracycline are 0.40, 0.52 and 0.60 μg mL^?1, respectively. The recommended method is suitable for automatic and continuous analysis and has been successfully tested for determination of tetracyclines in commercial formulations. The chemiluminescence intensity was found to be remarkably enhanced when in the presence of OP micellar system; possible reasons for this observed micellar induced enhanced chemiluminescence is given.     

Temperature-Induced Ionic Liquids Dispersive Liquid�CLiquid Microextraction of Tetracycline Antibiotics in Environmental Water Samples Assisted by Complexation

In this study, dispersive liquid?Cliquid microextraction (DLLME) combined with ultra high pressure liquid chromatography (UHPLC)?Ctunable ultraviolet detection (TUV), was developed for pre-concentration and determination of trace levels of tetracyclines, including 4-epitetracycline, 4-epichlortetracycline, doxycycline, chlortetracycline oxytetracycline, tetracycline, 4-epianhydrotetracycline and anhydrotetracycline, in aqueous samples. La (III) was used as the chelating agent to form a hydrophobic complex compound with tetracyclines, followed by extraction with ionic liquids. Some important parameters that may affect extraction efficiencies were examined and optimized. Under the optimum conditions, linearity of the method was observed in the range of 0.1?C200 ??g L^?1, with correlation coefficients (r ²) >0.992. The limits of detection and quantification were 0.031?C0.079 and 0.10?C0.26 ??g L^?1, respectively. The spiked recoveries of eight target compounds in river water, fishpond water and hog leachate were achieved in the range of 62.6?C96.3, 58.9?C94.5, 55.1?C86.1%, respectively.     

Simultaneous Determination of Ten Antibiotic Residues in Milk by UPLC

An analytical method for rapid screening and quantitative determination of ten antibiotics (chloramphenicol, thiamphenicol, tetracycline, oxytetracycline, chlortetracycline, metacycline, doxycycline, cefoperazone, ceftriaxone and cefaclor) residues in milk was developed using ultra performance liquid chromatography with photodiode array detector. After extraction with McIIvaine buffer + methanol (8 + 2), the extract was cleaned up with solid-phase extraction cartridge. The conditions of sample extraction, cleaning and separation were optimized. The average spiked recoveries of milk samples were 52.1–68.0, 70.1–81.0 and 76.2–101.0% at spiked levels of 0.1, 0.5, 2.5 μg g^?1, respectively with precisions of 3.3–15.9%. The limits of detection and quantification were 0.003–0.022 and 0.01–0.08 μg g^?1, respectively. The proposed method has been applied to the determination of antibiotics in actual milk samples with satisfactory results.     

Nonextractive Trace Level Simultaneous Determination of Mercury(II) and Zinc(II) in Environmental Samples with 2‐(5‐Bromo‐2‐pyridylazo)‐5‐diethylaminophenol and Cetylpyridinium Chloride

Abstract

A simple, rapid, selective, and sensitive method for the derivative spectrophotometric determination of Hg(II) and its simultaneous determination in the presence of Zn(II) using 2‐(5‐bromo‐2‐pyridylazo)‐5‐diethylaminophenol in the presence of cetylpyridinium chloride, a cationic surfactant, has been developed. The molar absorption coefficient and analytical sensitivity of the 1∶1 Hg(II) complex at 558 nm (λ_max) are 5.78×10⁴ L mol^?1 cm^?1 and 0.67 ng mL^?1, respectively. The detection limit of Hg(II) is 1.40×10^?2 ng mL^?1, and Beer's law is valid in the concentration range 0.05–2.40 µg mL^?1. Overlapping spectral profiles of Hg(II) and Zn(II) complexes in zero‐order mode interfere in their simultaneous determination. However, 0.10–2.00 µg mL^?1 of Hg(II) and 0.065–0.650 µg mL^?1 of Zn(II), when present together, can be simultaneously determined at zero cross point of the derivative spectrum, without any prior separation. The relative standard deviation for six replicate measurements of solutions containing 0.134 µg mL^?1 of Hg(II) and 0.620 µg mL^?1 of Zn(II) is 1.72 and 1.47%, respectively. The proposed method has successfully been evaluated for trace level simultaneous determination of Hg(II) and Zn(II) in environmental samples.     

Colorimetric Determination of Lead Using Gold Nanoparticles

A combined homogeneous assay and colorimetric determination method using gold nanoparticles was developed for rapid determination of lead(II) in contaminated natural waters. The presence of lead(II) in the colloidal gold suspension causes a change in the absorbance of the suspension. An increase in the absorption property at 595 nm is accompanied by a change in the size of the gold nanoparticles. High concentrations of lead cause aggregation of the gold colloids. Colloidal gold nanoparticles were synthesized using tannic acid as the reducing agent; this reagent allowed selective determination of lead in 10 µL of water, with a detection limit of 310 ng mL^?1 with an analysis time of 5 min. The coefficient of variation for lead(II) within the working range of the assay (520 ng mL^?1–13 µg mL^?1) varied from 1.3% to 9.2%. The limit of detection using this method with a sample volume of 50 µL was 60 ng mL^?1. The coefficient of variation for lead over the working range of the determined concentrations (80 ng mL^?1–25 µg mL^?1) varied from 0.2% to 9.3%, while the values for the inter-day assay (n = 8) were less than 10%. The method was employed for the analysis of river, lake, marsh, and spring water; the recovery of lead was determined to be 72.5%–130% for 10 µL of water and 93.6%–114.7% for 50 µL.     

Improved Multianalyte Determination of the Intense Sweeteners Aspartame and Acesulfame‐K with a Solid Sensing Zone Implemented in an FIA Scheme

Abstract

A multianalyte flow‐through sensor is proposed for the simultaneous determination of aspartame (AS) and acesulfame‐K (AK) in tabletop sweeteners. The procedure is based on the transient retention of AK in the ion exchanger Sephadex DEAE A‐25 placed in the flow‐through cell of a monochannel flow injection analysis (FIA) set‐up using pH 2.70 ortophosphoric acid/sodium dihydrogen phosphate buffer 0.06 M as carrier. In these conditions AS is very weakly retained, which makes it possible to measure the intrinsic ultraviolet (UV) absorbance of first AS and then AK after desorption by the carrier itself. The applicable concentration range, the detection limit, and the relative standard deviation were the following: for AS, from 10 to 100 µg mL^?1; 5.65 µg mL^?1; 3.4% (at 50 µg mL^?1); and for AK, between 40 and 100 µg mL^?1; 11.9 µg mL^?1 and 1.61% (at 50 µg mL^?1). The method was applied and validated satisfactorily for the determination of AS and AK blends in tabletop sweeteners. The results were compared against an HPLC reference method.     

Identification and Quantification of Heterologous Compounds Parthenin and Organic Acids in Parthenium Hysterophorus L. Using HPLC-PDA-MS-MS

Parthenium hysterophorus L., is an obnoxious weed known for its environmental health hazards and medicinal uses. These characteristics are due to presence of sesquiterpene lactones and organic acids; therefore a rapid and sensitive analytical procedure using HPLC-PDA-MS-MS was developed and optimized for separation, identification, and quantification of parthenin and six organic acids. Separation and characterization of compounds was achieved on a RP-C18 column with 1% acetic acid in water (A) and acetonitrile (B) as a mobile phase at a flow rate of 0.6 mL min^?1 and by matching their UV and mass spectra with reference compounds. Six organic acids (ferulic acid, 0.1 mg g^?1 to coumaric acid, 13.6 mg g^?1) and parthenin (27.4 mg g^?1) were characterized within 26 minutes of chromatographic separation in plant extract. The calibration curves are linear with correlation coefficients from 0.985 to 0.998, limit of detection and quantification ranged between 1.0 µg mL^?1 (anisic acid) to 2.2 µg mL^?1 (parthenin) and 2.5 µg mL^?1 (coumaric acid) to 5.2 µ g mL^?1 (parthenin) and recovery ranged between 90.9% to 97.3%. To the best of our knowledge this is the first report for the simultaneous separation of parthenin and organic acids. The method is applicable for screening of commercial crops, medicinal plants, and their products which might be mixed with P. hysterophorus during harvesting period.     

Determination of Veterinary Pharmaceuticals in Production Wastewater by HPTLC-Videodensitometry

An SPE-HPTLC method for simultaneous identification and quantification of seven pharmaceuticals in production wastewater was optimized and validated. The studied compounds were enrofloxacine, oxytetracycline, trimethoprim, sulfamethazine, sulfadiazine, sulfaguanidine and penicillin G/procaine. The method involves solid-phase extraction on hydrophilic-lipophilic balance cartridges with methanol and HPTLC analysis of extracts on CN modified chromatographic plates followed by videodensitometry at 254 and 366 nm. Optimization of chromatographic separation was performed by systematic variation of the mobile phase composition using genetic algorithm approach and the optimum mobile phase composition for TLC separation was 0.05 M H₂C₂O₄:methanol = 0.81:0.19 (v/v). Linearity of the method was demonstrated in the ranges from 1.5 to 15.0 μg L⁻¹ for enrofloxacine, 100–500 μg L⁻¹ for oxytetracycline, 150–600 μg L⁻¹ for trimethoprim, 300–1100 μg L⁻¹ for sulfaguanidine and 100–400 μg L⁻¹ for sulfamethazine, sulfadiazine and penicillin G/procaine with coefficients of determination higher than 0.991. Mean recoveries ranged from 74.6 to 117.1% and 55.1 to 108.0% for wellspring water and production wastewater, respectively. Only sulfaguanidine showed lower results. The described method has been applied to the determination of pharmaceuticals in wastewater samples from pharmaceutical industry.     

Determination of Poisonous Trace Element Thallium(I) by Kinetic Catalytic Reaction

Abstract

A effective and simple determination of poisonous trace element thallium(I) by means of kinetic catalytic reaction is proposed. The method is based on a catalytic effect of thallium(I) on a luminol-hydrogen peroxide system. Three different kinds of surfactants, cetrimonium bromide (CTMAB), sodium dodecyl sulphate (SDS), and Tween-80, are also investigated to improve the detection sensitivity. In optimum conditions, a highly selective and sensitive method for detecting trace thallium(I) has been established. The detection limit is 0.0073 µg · mL^?1, the relative standard deviation for six determinations of 0.04 µg · mL^?1 thallium(I) is less than 4.0%, and the linear range of determination is 0.02–0.1 µg · mL^?1.     

Development and Validation of an LC Method for Simultaneous Determination of Ascorbic Acid and Three Phenolic Acids in Sustained Release Tablets at Single Wavelength

A simple, rapid and sensitive column liquid chromatographic method was developed and validated to measure simultaneously the amount of ascorbic acid and phenolic acids at single wavelength (240 nm) in order to assess drug release profiles and drug-excipients compatibility studies for a new sustained release tablet formulation and its subsequent stability studies. A combined isocratic and linear gradient reversed-phase LC method was carried out at 240 nm. Quantification was achieved with reference to the external standards. The linearity for concentrations between 0.042 and 0.150 mg mL^?1 for ascorbic acid, 0.084–0.250 mg mL^?1 for chlorogenic acid, 0.053–0.360 mg mL^?1 for caffeic acid, and 0.016–0.250 mg mL^?1 for ferulic acid (r > 0.99 for all analytes) were established. The recovery of the active ingredients from the samples was at the range of 92.3–102.9%. Intra- and inter-day precisions were less than 2.5%. The limits of detection and quantification were 8 and 24 μg mL^?1 for ascorbic acid, 18 and 54 μg mL^?1 for chlorogenic acid, 37 and 112 μg mL^?1 for caffeic acid, and 11 and 34 μg mL^?1 for ferulic acid. The determination of the four active ingredients was not interfered by the excipients of the products. Samples were stable in the release mediums (37 °C) at least for 12 h.     

Determination of Explosives in Water Using Disposable Pipette Extraction and High Performance Liquid Chromatography

The use of disposable pipette extraction was examined for the simple and rapid determination of seven high explosives (cyclotrimethyl-enetrinitramine, cyclotetramethyl-enetetranitramine, 2,4,6-trinitrophenyl-methylnitramine, 2,4,6-trinitrotoluene, 2,4-dinitrotoluene, nitroglycerin, and pentaerythritol tetranitrate) in water. The current study involved the determination of slightly polar and nonpolar explosives in water with a reversed phase sorbent followed by high performance liquid chromatography. The method was based on a styrene divinylbenzene sorbent loosely placed inside a 5-mL pipette tip. Water samples were drawn into the tip and mixed with the sorbent. Air bubbles were also drawn through the tip following sample solution to enhance mixing. Because disposable pipette extraction uses small amounts of sorbent, minimal solvent is required to elute analytes and solvent evaporation is not necessary. The method provided rapid sample preparation, and required less than five minutes to extract 1.0 mL of water sample in the current study. Matrix-matched calibration was performed, and the limits of detection (LOD) were determined to be below 0.1 µg mL^?1 for all targeted explosives in water with an enrichment factor of two. Coefficients of determination (r²) were greater than 0.9990 for all studied explosives, and the recoveries ranged from 69.76% to 87.51%, 83.77% to 91.25%, and 83.62% to 98.99% for samples spiked at 0.25 µg mL^?1, 1.0 µg mL^?1, and 5.0 µg mL^?1, respectively. The relative standard deviations of recoveries at all spiked levels were below 8.97%. These results indicate that the disposable pipette extraction method provided good accuracy and precision for the determination of explosives in water.     

Simultaneous Estimation of Atorvastatin Calcium, Ramipril and Aspirin in Capsule Dosage Form by RP-LC

A simple, sensitive, precise and accurate reversed phase liquid chromatographic method has been developed for the simultaneous estimation of atorvastatin (AT) calcium, ramipril (RA) and aspirin (AS) from capsule dosage form. The method was developed using a Phenomenex Luna C₁₈ (250 mm, 4.6 mm i.d., 5 µm) column with a mobile phase consisting of 0.1%, orthophosphoric acid buffer:acetonitrile:methanol (45:50:5 v/v/v), pH 3.3, at a flow rate of 1 mL min^?1. Detection was carried out with ultra-violet detection at 210 nm. The retention times were about 12.19, 2.35, and 3.95 min for AT calcium, RA and AS, respectively. The developed method was validated for linearity, accuracy, precision, limit of detection, limit of quantitation and robustness. The linearity ranges were 1–6 µg mL^?1 for AT calcium, 0.5–3 µg mL^?1 for RA and 7.5–45 µg mL^?1 for AS with mean recoveries of 100.59 ± 0.68, 100.62 ± 0.83 and 100.49 ± 0.73% for AT calcium, RA and AS, respectively. Limit of detection obtained were 29.85 ng mL^?1 for AT calcium, 4.71 ng mL^?1 for RA and 85.13 ng mL^?1 for AS. Impurity of salicylic acid was found in capsule dosage form at the retention time of about 4.84 min. The proposed method can be used for the estimation of these drugs in combined dosage forms.     

Voltammetric Determination of Rosiglitazone in Pharmaceutical Preparations and Human Plasma

Abstract

The voltammetric behavior of rosiglitazone was studied using direct current (DC_t), differential pulse (DPP), and alternating current (AC_t) polarography. The drug manifests cathodic waves over a pH range of 2–11.2. In Britton‐Robinson buffer (BRb; pH 4), the diffusion current–concentration relationship was found to be rectilinear over a range of 4–24 µg · mL^?1 and 0.1–16 µg · mL^?1 using DC_t and DPP modes, respectively, with minimum limits of detection (LOD) of 0.15 µg · mL^?1 and 0.07 µg · mL^?1 using the DC_t and DDP modes, respectively. The diffusion‐current constant (I _d) was 6.63±0.03 (n=5). The proposed method was successfully applied to the determination of the studied compound both in pure form and in formulations. The mean percentage recoveries in tablets were 100.09±1.18 and 100.85±0.88 (n=5) using DC_t and DPP modes, respectively. Furthermore, the proposed method, adopting the DPP mode, was applied to the determination of rosiglitazone in spiked human plasma and the obtained mean percentage recoveries were 99.14±3.29 (n=4).     

Spectrophotometric Determination of Tetracyclines in Pure Form and in Pharmaceutical Preparations,by a Molybdenum Blue Method

Abstract

A new and sensitive spectrophotometric method has been developed for the determination of tetracyclines either in a pure form or in Pharmaceuticals, by a molybdenum blue method. The procedure is based on the observation that, in sulphuric acid medium, tetracyclines reduce ammonium molybdate to molybdenum blue, the absorbance of which is proportional to the amount of antibiotic present. The variables affecting development of the color have been investigated and the conditions optimized. Beer's law is obeyed for up to 20 μg/ml of tetracycline HCl and oxytetracycline HCl, 28 μg/ml of demeclocycline HCl, 18 μg/ml of chlortetracycline HCl, 32 μg/ml of doxycycline HCl and 40 μ/ml of rolitetracycline. Molar absorptivities (1 mol^?1 cm^?1) and Sandell's sensitivities (μ cm^?2 per 0.001 absorbance unit) are, respectively: tetracycline HCl 4.9×10⁴ and 0.0098, oxytetracycline HCl 5.4×10⁴ and 0.0092, demeclocycline HCl 1.6×10⁴ and 0.0313, chlortetracycline HCl 5.5×10⁴ and 0.0094, doxycycline HCl 3.4×10⁴ and 0.0141, rolitetracycline 2.7×10⁴ and 0.0195.     

Optimization,Validation and Application of a Capillary Zone Electrophoresis Method for the Assay of Sparfloxacin in Pharmaceutical Formulation

Abstract

A capillary zone electrophoresis (CZE) method has been developed for the determination of the antibiotic sparfloxacin in tablets. The CZE separation was performed using 75 µm×35 cm fused-silica capillary under the following conditions: 25°C; applied voltage, 12 kV; 25 mM H₃PO₄-NaOH running buffer (pH 8.5). The detection wavelength was 254 nm. Flumequine was used as internal standard (IS). The method was suitably validated with respect to linearity, limit of detection and quantification, accuracy, precision, specificity, and robustness. The calibration was linear from 10 to 60 µg mL^?1 and the limit of detection and quantification were 5.38 and 9.46 µg mL^?1, respectively. Recoveries ranging from 95.68%–102.4% were obtained in the determination of sparfloxacin that were spiked to placebos. Excipients in the commercial tablets and degraded products from different stress conditions did not interfere in the assay. The method was successfully applied to the determination of sparfloxacin in pharmaceutical tablets.     

Flow Injection Spectrophotometric Determination of the Antibacterial Levofloxacin in Tablets and Human Urine

Abstract

A sensitive and fast flow‐injection (FI) spectrophotometric method for the determination of levofloxacin based on the formation of a colored product upon oxidation with N‐bromosuccinimide (NBS) in acidic medium is proposed. Optimization of chemical and FI variables has been made. Under the optimized conditions, the sampling rate was over 90 h^?1, the calibration curve obtained was linear over the range 10–300 µg·mL^?1, and the detection limit was 3 µg·mL^?1. The proposed method was successfully applied to the determination of levofloxacin in pharmaceuticals and human urine samples. It was also found that the excipients in the commercial tablet preparation did not interfere with the assay. Results are precise (RSD<2.7%; n =10) and in agreement with those found by the reference high pressure liquid chromatography (HPLC) procedure.     

On-Line Two-Dimension Liquid Chromatography for the Analysis of Ingredients in the Medicinal Preparation of Coptis Chinensis Franch

An on-line two-dimension microflow liquid chromatography was developed for better separation and analysis of the highly complex ingredients of medicinal preparation of traditional Chinese medicine Coptis Chinensis Franch. A two-valve switching system was utilized for two-dimension chromatography with strong cation exchange and reverse-phase capillary columns separation. The components were separated well by this system and yielded over 420 peaks. Under the optimal condition, 4 compounds were detected quantitatively. A good linear relationship was obtained from 0.2 µg mL^?1 to 24 µg mL^?1with detection limits (S/N = 3) ranging from 0.05 µg mL^?1 to 0.2 µg mL^?1for the compounds. We demonstrated that the method can be successfully applied to the analysis of a natural complex sample, with satisfactory results.     

A novel chemiluminescence reaction system for the determination of lincomycin with diperiodatonickelate(IV)

A sensitive and high selective chemiluminescence (CL) method was developed for the determination of lincomycin in acid medium using diperiodatonickelate as a reagent. The mechanism leading to luminescence is discussed by comparing the spectra of fluorescence and CL. Relative CL intensity is linear in the range from 8.0 ng mL^?1 to 1.0 µg mL^?1, the limit of detection is 2.5 ng mL^?1 (3σ), and the relative standard deviation is 4.0% at 0.1 µg mL^?1 of lincomycin (n?=?7). The method was successfully applied to the determination of lincomycin in injections, human urine, and in serum samples.     

Simultaneous Determination of Organotin Compounds in White Wine by Gas Chromatography-Mass Spectrometry

A simple, reliable, and effective analytical method was developed for the simultaneous determination of five organotin compounds (OTCs) including monobutyltin trichloride dibutyltin dichloride tributyltin chloride tetrabutyltin and triphenyltin chloride in white wines. The OTCs were derivatized with sodium tetraethylborate (NaBEt₄), and their derivatives were extracted by liquid-liquid extraction (LLE) into n-hexane. The experimental variables, such as type and volume of extraction solvents, amount of derivatization reagent NaBEt₄ and extraction time were optimized. The determination of ethylated derivatives of OTCs in the final extracts was carried out by gas chromatography-mass spectrometry (GC-MS). Under optimized conditions, good linearity was observed when analytical concentrations were in the range of 0.01–4.0 µg · mL^?1, the linearity correlation coefficients were between 0.9982 and 0.9987, with the LODs in the range of 0.2–3.0 µg · L^?1, and the LOQs varied from 0.6 to 10.0 µg · L^?1. The obtained recoveries were in the range of 78.0–120.0%, with the relative standard deviations equal to or lower than 8.1%. This method was applied to the determination of OTCs in white wines with satisfactory results.