电感耦合等离子体发射光谱法测定高纯铝中硅

建立电感耦合等离子体发射光谱(ICP-AES)法测定高纯铝中硅元素的分析方法。样品采用碱溶法进行预处理,以氢氧化钠溶液溶解,再加入盐酸、硝酸酸化。选取了硅251.611 nm分析谱线进行分析。硅的质量分数在0.001%~0.01%范围内与光谱强度具有良好的线性关系,线性相关系数为0.9991。该方法检出限为0.00012%,测定结果的相对标准偏差不大于10.2%(n=8),加标回收率为93.2%~104.2%。该方法操作简便,测定结果准确、可靠,适用于快速检测高纯铝中硅元素,具有推广价值。     

电感耦合等离子体发射光谱法检测镍基/钴基高温合金中硼磷硅

采用一定比例的混合酸溶解样品,利用基体匹配配制一系列标液消除基体的影响,以及轴向观测喷嘴吹扫技术来提高待测元素的灵敏度,使用电感耦合等离子体发射光谱(ICP-OES)测定镍基/钴基高温合金中硼磷硅。各元素选的分析线依次为B 182.577 nm、P 178.222 nm、Si 185.005 nm。检测范围分别是：B：0.001%-3.0%,P：0.003%-0.20%,Si：0.005%-3.0%,检出限范围是0.00005%-0.0004%,线性相关系数>0.9995。加标回收率为90.0%-105.0%,精密度RSD<2.0%。该方法操作简单快速,结果令人满意。     

Silicon determination by inductively coupled plasma atomic emission spectrometry after generation of volatile silicon tetrafluoride

A method for the determination of silicon by inductively coupled plasma atomic emission spectrometry (ICP-AES) is described. The procedure is based on a discontinuous generation of volatile silicon tetrafluoride in concentrated sulphuric acid medium after injecting 125 μl of 0.1%, w/v sodium fluoride solution into 100 μl of the sample. The gaseous silicon tetrafluoride is fed directly into the ICP torch by a flow of 250 ml min⁻¹ Ar carrier gas. The calibration curve was linear up to at least 100 μg ml⁻¹ of Si(IV) and the absolute detection limit was 9.8 ng working with a solution volume of 100 μl. The relative standard deviation for six measurements of 10 μg ml⁻¹ of Si(IV) was 2.32%. The method was applied to the determination of silicon in water and iron ores.     

火焰原子吸收光谱法测定锌合金中镁

建立火焰原子吸收光谱法测定锌合金中镁含量。选用10 mL盐酸溶液(1+1)溶解样品,加入5 mL质量浓度为100 g/L的LaCl3溶液,以消除铝对镁的化学干扰,在选定的仪器工作条件下进行测定。结果表明,镁的质量浓度在0~1.238 mg/L范围内与与吸光度具有良好的线性关系,相关系数为0.999 4,线性方程为Y=1.086 4X+0.018 5,方法测定下限为0.010 mg/L。样品测定结果的相对标准偏差为1.61%~3.45%(n=6),加标回收率为91.3%~94.7%。该方法准确度高,精密度好,满足锌合金中镁含量的日常检测要求。     

Determination of chloride ion in aqueous samples by isotope-dilution Fourier-transform flame infrared emission (ID-FIRE) spectrometry

An isotope dilution method for the determination of chloride ion in aqueous samples is described. The method makes use of the isotopic shift in the rotational lines of the 1–0 band of HCl emitted in the near infrared region of the spectrum by vibrationally excited HCl molecules present in a hydrogen/entrained air flame. Chloride ion in the sample is converted to chlorine gas by electrolysis and swept into a hydrogen/entrained air flame where it is converted into HCl. Because isotope dilution is an absolute method of analysis, matrix effects are minimized, and the chlorine generation step need not be quantitative. With the system described in this paper, samples must contain at least 9 mg of chloride ion per ml, and a 2-ml sample is required. Over the range from 10 to 30 mg Cl⁻ ml⁻¹, the average error was −0.96%, and the average relative standard deviation was 3.3% for seven samples using seven of the more intense lines in the P branch. Compared with standard silver nitrate titrations, the isotope dilution procedure was not affected by such common interferences as bromide ion and iodide ion. The technique was applied to several seawater samples from different regions.     

Digital image-based flame emission spectrometry

A digital image-based flame emission spectrometric (DIB-FES) method for the quantitative chemical analysis is proposed here for the first time. The DIB-FES method employs a webcam to capture the digital images which are associated to a radiation emitted by the analyte into an air-butane flame. Since the detection by webcam is based on the RGB (red-green-blue) colour system, a novel mathematical model was developed in order to build DIB-FES analytical curves and estimate figures of merit for the proposed method. In this approach, each image is retrieved in the three R, G and B individual components and their values were used to define a position vector in RGB three-dimensional space. The norm of this vector is then adopted as the RGB-based value (analytical response) and it has revealed to be linearly related to the analyte concentration. The feasibility of the DIB-FES method is illustrated in three applications involving the determination of lithium, sodium and calcium in anti-depressive drug, physiological serum and water, respectively. In comparison with the traditional flame emission spectrometry (trad-FES), no statistic difference has been observed between the results by applying the paired t-test at the 95% confidence level. However, the DIB-FES method has offered the largest sensitivities and precision, as well as the smallest limits of detection and quantification for the three analytes. These advantageous characteristics are attributed to the trivariate nature of the detection by webcam.     

火焰原子吸收法测定鸡尾木中无机元素的含量

鸡尾木(ExcoecariaVenenataS.LeeetF.N.Wei)属大戟科,海漆属,为民间药用珍贵植物,用于治疗牛皮癣、慢性湿疹等,疗效颇佳[1]。鸡尾木中无机元素,尤其是医学微量元素的测定对其药理效的研究有重要的参考价值。1　实验部分1 1　仪器及试剂TAS 986原子吸收分光光度计(北京普析通用仪器有限责任公司);空心阴极灯:Fe、Cu、Ni、Cr、Cd、Zn、Co、Ba、Ca(北京瑞利普光电器厂);Mg、Pb(北京真空电子技术总公司);Mn(北京市朝阳天宫电器厂);AdventurerTM电子天平(奥豪斯国际贸易〈上海〉有限公司)。标准储备液:配制Zn2+、Mg2+、Fe3+、Mn2…     

Detection of sulphate by flame emission spectrometry

A reasonably simple method for the determination of sulphate is presented. The method is based on disulphur molecular emission, produced in a hydrogen-nitrogen diffusion flame, utilizing a conventional atomic absorption spectrometer, with simple accessories to handle in-line ion-exchange pretreatment. A simplex program was written and used to obtain optimum experimental conditions. Disulphur emission was found to occur at temperatures from below 150°C; the optimum temperature is ca. 200°C. The method can be used for the determination of sulphate down to ca. 10 mg S l^?1.     

液相色谱-质谱联用法测定血液中全氟化合物

研究了快速溶剂萃取-液相色谱/质谱联用技术测定血液中PFAAs的方法。血液样品经过冷冻干燥,利用加速溶剂萃取的方法,最后使用液相色谱-质谱仪分析检测PFAAs成分。方法的回收率为74.6%~128.8%,检出限为1.10~25.1 ng/L。通过对珠江三角洲地区人群血液样本的分析,发现∑9PFAAs的浓度为26.8~557 ng/g,平均值为176±90.1 ng/g。血液中PFAAs的主要成分以PFHxA和PFOS为主,分别占血液中PFAAs浓度的20.97%和66.98%。人群血液中最常见和浓度最高的PFAAs是PFOS,而PFOA浓度相对较低。     

火焰原子吸收光谱法测定炭末中银

炭末中银的准确测定对于其金属平衡和贸易结算具有重要意义。采用硝酸-硫酸体系除碳分解试样,在20%盐酸介质中,采用空气-乙炔火焰,以328.1nm作为测定波长,建立了火焰原子吸收光谱法（FAAS）测定炭末中银的方法。在最优的实验条件下,银质量浓度在0.30~3.00μg/mL范围内与其吸光度呈良好线性关系,相关系数为0.9999。方法检出限为0.004μg/mL,定量下限为0.013μg/mL。干扰试验表明,根据炭末中干扰元素含量,在载金炭国家标准物质中加入一定量的共存元素,共存元素不影响银量的测定。实验方法用于测定实际炭末样品中银,结果的相对标准偏差（RSD,n=7）为0.91%~3.4%,且结果与《GB∕T 29509.2-2013 载金炭化学分析方法 第2部分：银量的测定 火焰原子吸收光谱法》方法测定结果一致。按照实验方法测定了4个载金炭标准样品中银,结果与标准值吻合。准确度和精密度符合实际生产需求,可用于炭末中银的测定。     

火焰原子吸收光谱法测定茯苓中微量元素

本文确定了各微量元素火焰原子吸收光谱仪的工作条件,建立了各微量元素线性回归方程.应用火焰原子吸收光谱法测定了天然茯苓和液体发酵茯苓中微量元素含量.研究结果表明二者微量元素含量存在一定的差异,探讨了产生上述差异的原因.     

电感耦合等离子体原子发射光谱法测定高温合金中低含量钇

建立电感耦合等离子体原子发射光谱法测定高温合金中低含量钇的方法。采用盐酸、硝酸、氢氟酸溶解样品,在优化的仪器条件下,采用基体匹配法配制系列标准工作溶液,选择分析线为360.073 nm。钇的含量在0.0005%~0.050%范围内与光谱强度具有良好的线性关系,相关系数为0.99999,检出限为0.000003%。该方法测定结果的相对标准偏差不大于6.0%(n=8),加标回收率为90.0%~104.0%。该方法简便、快速、准确,可用于高温合金中低含量钇的测定。     

碱消解-火焰原子吸收光谱法测定土壤中六价铬

建立了碱消解-火焰原子吸收光谱法测定土壤中六价铬的方法.讨论了pH值对六价铬测定的影响.干扰实验的结果表明同等含量的三价铬对六价铬测定无干扰.实验对比了无背景校正、氘灯背景校正、塞曼背景校正三种工作方式,分别对低、中、高三个水平土壤六价铬标准物质进行了测定,结果表明,低含量的土壤样品用塞曼背景校正方式测定的结果更准确,...     

Determination of rubidium in blood by flame emission spectrometry

Rubidium in plasma and whole blood was determined by flame atomic emission spectrometry after dilution 10× and 100× respectively with a 2.5 g Cs l^?1 solution used as an ionization suppressor. The method is more sensitive than inductively coupled plasma, and much simpler than, e.g., neutron activation analysis.     

电子制冷预浓缩-双柱气相色谱-质谱/氢火焰检测器法测定空气中104种挥发性有机物

基于吸附剂辅助电子制冷预浓缩技术，建立了多维切割双柱气相色谱-质谱/氢火焰离子化检测器（GC-MS/FID）同时测定环境空气中104种挥发性有机物（VOCs）的方法。将采集于苏玛罐中的环境空气样品在配有吸附剂的电子制冷预浓缩系统中富集、脱附、除水、除CO₂和浓缩，然后通过GC-MS/FID的多维切割单元将C₂~C₃组分和C₄~C₁₂组分分别引入PLOT柱和InterCap-624柱进行分离。C₂~C₃组分用FID检测，以保留时间定性、外标法定量；C₄~C₁₂组分采用电子轰击离子源质谱检测，以保留时间和特征离子定性、内标法定量。考察了冷阱吸附剂种类、辅助压力控制单元压力设置、双柱切换时间切割点等参数对分析结果的影响，优化了GC-MS/FID条件，并评估了在此优化条件下的方法性能。104种VOCs在0.0446~0.892 μmol/m³范围内线性关系良好，相关系数（r）为0.9984~0.9999，对0.0446 μmol/m³和0.223 μmol/m³水平的混合标准气体重复6次进样，平均回收率为86.4%~116.1%，相对标准偏差为0.9%~11.3%；方法的检出限为0.145~1.90 μg/m³，定量限为0.435~5.70 μg/m³。该法稳定性好，灵敏度高，操作简便，可用于环境空气中104种VOCs的测定。     

锌精矿中铟的测定

应用电感耦合等离子体发射光谱法测定锌精矿中的铟,确定了最佳工作条件,选择了最佳分析谱线,并利用标准加入法和基体匹配法确定了该方法的准确性。样品用氟化氢铵、盐酸、硝酸、高氯酸溶样,用盐酸浸取。本法与萃取分离盐酸羟胺示波极谱法测定的铟含量结果一致。方法准确,快速,加标回收率为99.6%~101.7%,相对标准偏差为0.97%~2.1%。     

火花放电原子发射光谱分析方法测定镍基合金中12种元素

化学元素的含量及其变化影响镍基合金材料的各项性能。因此准确检测镍基合金化学成分并对其严格控制,对提高和保证镍基合金材料性能具有重要意义。通过对仪器分析条件进行优化,采用控制样品法,建立了用火花放电原子发射光谱测定镍基合金中Al、C、Cr、Co、Cu、Fe、Nb、P、Si、S、W、Mo等12种元素含量的方法。优化的试验条件如下：①吹氩时间6 s;②预燃时间6 s;③积分时间8 s。应用此方法分析了三种常规镍基合金样品,测定值与现行国家标准分析方法结果一致。     

Determination of boron in boron-alloyed steels by inductively coupled plasma atomic emission spectrometry

An inductively coupled plasma atomic emission spectrometry (ICP-AES) procedure has been developed and examined for the determination of boron content (0.01 up to about 2% B) in boron-alloyed steels such as POLDI ATA BOR (65% Fe, 19%Cr, 12% Ni, 1.5% Mn, 1% B), POLDI ATA BOR EXTRA (62% Fe, 18% Cr, 13% Ni, 2.5% Mo, 1.5% Mn, 1% B) and POLDI ATA BOR-R (75% Fe, 18% Cr, 3.5% Ti, 1.8% B). The steel sample is dissolved with a mixture of hydrochloric, nitric, sulfuric and phosphoric acids in a quartz vessel. Borides of alloyed metals, especially of iron and chromium, are quantitatively decomposed. The presence of phosphoric acid in a sample solution reduces the volatility of boric acid with water vapour.Presented in part at the 1989 European Winter Conference on Plasma Spectrochemistry, Reutte, Austria     

微波消解-电感耦合等离子体发射光谱法测定土壤中的硫

利用微波消解仪消解土壤样品,采用电感藕合等离子体发射光谱仪测定土壤中硫的含量。以浓王水为消解试剂,对土壤样品进行微波消解,优化了王水用量,考察了微波消解条件、谱线干扰情况和仪器参数对硫灵敏度的影响。硫的质量浓度在0~40 mg/L范围内与光谱强度具有良好的线性关系,线性相关系数为0.9997,硫的检出限为0.053 mg/L。土壤中硫测定结果的相对标准偏差为1.54%~7.84%(n=7)。对六种土壤国家一级标准物质进行了测定,测定结果与推荐值相符,无显著性差异。该方法简便、准确,分析效率高,能够满足日常批量样品分析的要求。     

ICP-AES 法测定硅铁中痕量元素

采用电感耦合等离子原子发射光谱法测定硅铁中的痕量元素,研究了 Fe 基体对被测元素的影响,并选择了最佳工作条件.被测元素的检测限为 0 .60～76.2 ng/mL,样品加标回收率为 92%～108%,RSD(n=8)<3%.