Determination of Trace Amounts of Copper by Adsorptive Stripping Voltammetry

ABSTRACT

A technique is presented for the determination of trace amounts of copper(II) by adsorptive cathodic stripping voltammetry. The procedure is based on adsorptive accumulation of copper(II)-Alizarin Red S (ARS) complex on a hanging mercury drop electrode, followed by a stripping voltammetric measurement of the reduction current of the adsorbed complex at -0.16 V (vs. Ag/AgCl). The height of the copper -ARS reduction peak is linearly dependent upon the copper(II) concentration between 0.2-15 and 15-500 ng.ml^?1. The detection limit of the technique is 0.05 ng.ml^?1 copper(II) for a collection time of 1 minute. The method is free from most interferences. The procedure has been successfully applied to the determination of trace amounts of copper(II) in some analytical grade salts.     

Indirect Pyrophosphate Determination by Atomic Absorption Using Copper(II) Ions and A Liquid Ion Exchanger

Abstract

Pyrophosphate (5 × 10^?6 M to 5 × 10^?6 M in the final aqueous solution) may be determined in the presence of similar concentrations of phosphate, other condensed phosphates, or some other anions, by measurement of its inhibitory effect on the extraction of copper(II) by Amberlite LA-1 into MIBK or ethyl acetate. The copper extracted is determined by atomic absorption spectrophotometry.     

Determination of Molybdenum(VI) At Trace Levels by a Catalytic Polarographic Method

Abstract

ARSTRACT

A d.c. polarography method for molybdenum (VI) determination at trace levels has been developed. The reaction is catalytic between molybdenum, salicylaldoxime (SCAD) and bromate in acetic-acetate medium. The obtained peak is proportional to molybdenum (VI) concentrations in the range 1.08.10^?a to 1.37.10^?6 M. The proposed procedure is selective, the most serious interferents being W(VI), Pb(II) and Fe(II). It is applied to molybdenum determination in steel samples after iron extraction by ethyl ether.     

Electrochemical solid-phase nanoextraction of copper(II) on a magnesium oxinate-modified carbon paste electrode by cyclic voltammetry

Solid-phase nanoextraction is a sample preparation technique, which combines nanotechnology with analytical chemistry, and brings analytical chemistry to a higher level, particularly for complex system analysis. This paper describes a typical example of electrochemical solid-phase nanoextraction and electrochemical detection. Trace amounts of copper (5.0?×?10^?13?mol/L) were extracted by electrochemical solid-phase nanoextraction on to the magnesium oxinate nanoparticle-modified carbon paste electrode surface in a pH?7.2 phosphate buffer system at ?0.50 V for 100 s. The extraction is achieved by the cation exchange between copper(II) in the aqueous solution and magnesium(II) from the magnesium oxinate nanoparticles on the electrode surface. The extracted copper shows an irreversible anodic peak at about 0.2 V (vs. saturated calomel electrode). The peak current is proportional to the scan rate, which shows this to be a surface-controlled process. The oxidation peak current is proportional to the logarithm of the copper concentration in the range 5.0?×?10^?13?～?5.0?×?10^?7?M with a slope of 2.215. This powerful method uses the carbon paste electrode to combine extraction with electrochemical analysis.     

Trace Analysis of Lead and Copper Ions in Fish Tissue Using Paste Electrodes

Abstract

DNA was immobilized onto a carbon nanotube surface through cyclic voltammetry, in which paste electrode (PE) was subjected to lead and copper trace ion analysis. Optimized conditions for square‐wave stripping voltammetry were then searched. The results indicated three other linear working ranges—3–21 mg l^?1, 2–16 µg l^?1, and 3–17 ng l^?1 Pb(II) Cu(II)—within an accumulation time of 190 s in 0.1‐M ammonium phosphate electrolyte solutions of pH 10.0. At the optimized conditions, the detection limit (S/N) was pegged at 0.4 ng l^?1 (1.93×10^?12 M Pb(II) and 6.29×10^?12 M Cu(II)). And the relative standard deviation at 10 mg l^?1 Pb(II) and Cu(II) was a 0.074 and 0.069% precision, in 15 measurements. The method can be applied to assays of fish tissue.     

A Prospect for the Analysis of Species Acting as Enzyme Inhibitors as Illustrated by Heavy Metal Inhibition

Abstract

A flow system incorporating an amperometric glucose oxidase enzyme electrode has been used to study the inhibitory effects of 16 metal cations on glucose oxidase. Only copper(II), mercury(II) and silver(I) caused any significant inhibition. the enzyme electrode could be reactivated by EDTA, the reactivation being most effective for copper(II) and least so for silver(I). Other complexing agents were tried for reactivation but proved to be unsatisfactory.

The ability to reactivate the enzyme on the electrode following copper(II) inhibition, and the linear response of the system to the level of this inhibitor according to I/A = -9.49 × 10^?7 log([Cu]/M) + 4.84 × 10^?8; r = 0.994 between 2.5 × 10^?4M and 5 × 10^?3M [Cu]²⁺ indicates a prospect for the use of a flow system for determining enzyme inhibitors in samples.     

Catalytic Square-Wave Voltammetric Determination of Acrylamide in Potato Chips

Abstract

Square-wave voltammetry is a fast technique used for determination of trace amounts of acrylamide. When cobalt(II) ions were added to the acrylamide solution, a catalytic peak at about ?1.35 V vs. Ag/AgCl was observed, which was proportional to acrylamide concentration. The calibration curve showed good linearity in the range of 200–800 ng mL^?1 of acrylamide with a regression coefficient of 0.9989. The limit of detection of the method was 3.52 ng mL^?1, and the relative standard deviations for concentrations of 300 ng mL^?1 and 700 ng mL^?1 were 99.8% × 10^?2 and 79.7% × 10^?2, respectively.     

Synthesis and Study of the Fluorescent Character of a New Fluorescent Reagent 3-Pheny1-5-(2′-Carboxy1phenylazo)-2-Thioxo-4-Thiazolinone

Abstract

The paper reports the synthesis of a new fluorescent reagent 3-pheny1-5-(2′-carboxy1phenylazo)-2-thioxo-4-thiazolinone (3PRACP). The product has been purified by column absorption chromatography. Its conposition has been confirmed by elemental analysis, IR, HNMR and MS. We also studied its fluorescent properties At pH=5.6, 3PRACP can form a chelate with trace Cu²⁺ and when λ ex/λ em=305nm/405nm, the fluorescence is very intense. The fluorescent intensity has a linear relationship with the concentration of Cu²⁺ in the range of (0.1 – 48) × 10^?9 M. The sensitivity is 8X10^?9. Using the method, we detected trace copper in pork and vegetable, with good results.     

Electrochemical Behavior of 6-Mercapto-Purine at Hanging Copper Amalgam Dropping Electrode and Its Trace Determination by Differential Pulse Adsorption Cathodic Stripping Voltammetry

Abstract

The electrochemical behavior of 6-MP was studied by cyclic voltammetry at a hanging copper amalgam dropping electrode (HCADE). It was found that 6-MP could form a complex with the Cu(II) stripped from the HCADE, showing a new peak at ?0.19V in the medium of 0.1mol/L LiClO₄-0.5mol/L HClO₄ solution. The mechanism of the reaction was proposed. This new peak was sensitive and could be used for the determination of trace 6-MP by differential pulse adsorption cathodic stripping voltammetry (DPAdCSV). The linear range was from 3.6×10^?10 to 5.3×10^?6 mol/L, and the detection limit was about 1.2×10^?10 mol/L (S/N=3). The method was also successfully applied to the determination of 6-MP in pharmaceutical tablets.     

Adsorptive Stripping Voltammetric Determination of Albendazole at a Hanging Mercury Drop Electrode

ABSTRACT

Albendazole is determined by differential-pulse adsorptive cathodic stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper(II) complex at ?0.28V at an accumulation potential 0.0V vs. Ag/AgCl electrode. The optimum conditions of pH, accumulation potential and accumulation time were studied. The calibration graph for the determination of albendazole was linear in the range 3.0X10^?8 - 9X10^?7M with a relative standard deviation of 2.8%. The detection limit was 1.0X10^?8M after 180s accumulation at 0.0V. The effect of common excipients and metal ions on the peak height of albendazole was studied. The presence of Cu²⁺ ions forms a stable complex with albendazole which is strongly adsorbed at the mercury electrode surface. The method was applied to the determination of the drug in commercially available dosage forms.     

Indirect Spectrophotometric Determination of Vanadium(IV) by Flow Injection Analysis Based on the Redox Reaction with Copper(II) in the Presence of Neocuproine

Abstract

An indirect photometric method with a continuous-flow analysis is presented for the determination of trace amounts of vanadium(IV). It is based on the redox reaction of copper(II) with vanadium(1V) in the presence of neocuproine. In the presence of neocuproine, copper(I1) is reduced easily by vanadium(I V) to a copper(1)-neocuproine complex, which shows a n absorption maximum at 454 nm. By measuring t h e absorbance of the complex at this wavelength, vanadium(1V) in t h e range 2×10^?6 - 8 × mol dm^?5 mol dm^?3 can be determined at a rate of 120 samples h^?1. The fractional determination of vanadium(1V) and iron(I1) is also studied.     

Potentiometric flow-injection determination of trace chlorine based on its redox reaction with an iron(III)/iron(II) buffer

A very sensitive and rapid potentiometric determination of trace chlorine in water is described. The method is based on the transient potential changes which appears during the reduction of dissolved chlorin with an iron(III)/iron(II) potential buffer containing chloride and sulfuric acid. The sample is injected into a water carrier stream and merged with a stream of this potential buffer solution; chlorine is reduced during passage through a short reaction coil. The potential change from the baseline is measured with a flow-through ORP (oxidation-reduction potential) electrode. Potential changes (peak heights) are proportional to chlorine concentrations from 10^?7 M to 10^?5 M. The detection limit is 5 × 10^?8 M (3.5 μgl^?1 as Cl₂). The sample throughput is 45 h^?1. Reproducibility is in the range 2.5–1.1%. Results for potable water agree with those obtained by the o-tolidine method.     

Indirect Determination of Trace Tetraborate by Differential Pulse Polarography Using Its Copper Complex and Application to Waste and Drinking Water

A new differential pulse polarographic (DPP) method has been developed for the trace determination of boron. Its most stable copper complex is used in 0.5 M KNO₃ electrolyte since boron is not electroactive. By continuous addition of tetraborate to copper solution, the copper peak decreased first but then the peak became very small and nearly constant. This point was used for the boron determination. It was found that one mole of copper used two moles of tetraborate. Using this relationship, 1×10^?5 M tetraborate could be determined. The quantification limit was 2.5×10^?6 M and detection limit was 8×10^?7 M. In the presence of complex forming ions such as Pb, Zn, and Cd, the borate found in sample was somewhat smaller because of their reaction with borate. But since their complexes were not as strong as copper, only a few percent of borate were used. No interference was observed in the presence of calcium, chloride and sulfate. This method is applied for the determination of B in borax ore, waste water of borax industries and tap water of Ankara city.     

Voltammetric Detection of Captopril Using Copper(II) and an Unmodified Glassy Carbon Electrode

We report a simple, sensitive, and rapid detection of captopril using copper(II) and a bare glassy carbon electrode with cyclic voltammetry. The captopril is detected by the formation of a copper(II)‐captopril complex that is observed to have a characteristic oxidation potential at+0.24 V vs. Ag/AgCl. It is found that the peak current varies linearly with the concentration of captopril. The linear dynamic range is obtained for a captopril concentration of 1 µM to 10 µM, and the sensitivity is found to be 0.10±0.003 μA μM^?1. Importantly, the low limit of detection (n=3) of 0.10 μM and the precision of 3.2 %, are achieved using a simple, unmodified electrode. This is attributable to in situ adsorption of a copper(II)‐captopril complex on the electrode surface.     

Study and Application on Polarographic Catalytic Wave of Human Serum Albumin in the Presence of Kio3

ABSTRACT

A polarographic catalytic wave of human serum albumin (HSA) in the presence of KIO³ was reported. In 0.1 M NaAc～HAc buffer (pH4.7) solution, a reduction wave of HSA with peak potential ?0.60 V (vs., Ag/AgCl) resulted from the reduction of five disulfide linkages to sulfhydryl group. In the presence of KIO³, HSA yielded a polarographic catalytic wave at the original potential due to reduction and regeneration of these disulfide linkages. The catalytic wave can be used to determine trace of HSA. In the 0.1 M HAc～NaAc (pH4.7±0.2) ～1×10^?3 M KIO³ solution, the peak current was linearly proportional to HSA concentration in the range of 1.5×10^?7～7.5×10^?7 M. The catalytic wave improved two orders of magnitude in sensitivity compared with corresponding reduction wave.     

Extraction,Separation and Spectrophotometric Determination of Bismuth(III) Using 1(4′-Bromophenyl) 4,4,6-Trimethyl (1H,4H)-Pyrimidine-2-Thiol

Abstract

The operating conditions for the spectrophotometric determination of bismuth(III) with 1-(4′-bromophenyl)-4,4,6-trimethyl-(1H,4H)-pyrimidine-2-thiol (4′bromo PTPT) as a ligand by a liquid-liquid extraction technique are presented. In acidic conditions bismuth(III) forms a yellow complex with the ligand which can be extracted in chloroform with an absorption maxima at 410 nm. The molar absorptivity is 1.5×10⁴ l mole^?1 cm^?1 and Sandell's sensitivity is 14.3 ng cm^?2. The difference in the absorbance between the chloroform blank and bismuth(III) sample increases linearly in the concentration range 2-14 ppm at 0.3 M hydrochloric acid. The proposed method is extremely sensitive, rapid, reproducible and has been satisfactorily applied to the determination of trace amounts of bismuth(III) in synthetic mixtures, alloys and pharmaceutical formulations and also provides binary separation of bismuth(III) from selenium, tellurium, lead, antimony, copper and gold. The overall process of extraction and determination takes about 15 to 20 min.     

Potentiometric and spectrophotometric flow-injection determinations of metal ions with use of metal ion buffers

Potentiometric and spectrophotometric flow-injection determinations of metal ions, based on metal ion buffers, are described. A copper(II) ion-selective electrode and copper(II) ion buffers containing nitrilotriacetic acid (NTA) or ethylenebis(oxyethylenedinitrilo)tetraacetic acid (EGTA) are used for determination of ca. 10^?3 M transition metal ions or of calcium in the presence of magnesium. Spectrophotometric determination of transition metal ions is achieved by using a zinc ion buffer solution containing NTA and xylenol orange as indicator. Zinc concentrations up to 2 M can be determined by using large dispersion in the manifold. The factors influencing the sensitivity of the proposed methods are discussed.     

Near-Infrared Fluorimetric Determination of Copper(Ⅱ) Ions Using CdHgTe Nanorods as Probe

Stable water‐soluble CdHgTe nanorods with an emission wavelength at 722 nm, obtained by doping Hg²⁺ into CdTe nanorods, has been used as a near‐infrared region (NIR) probe to investigate their interaction with copper(II) ions. A new fluorimetric method for the determination of copper(II) ions has been developed based on the quenching effect of copper(II) ions on the emission of CdHgTe nanorods. The mechanism studies show that an effective electron transfer from nanorods to the copper(II) ions occurred based on the coordination reaction between copper(II) ions and the carboxyl groups on the nanorods surface, which could be responsible for the emission quenching of CdHgTe nanorods. Under optimum conditions, the linear range of the calibration curve for the determination of Cu²⁺ is from 8.0×10^?9 to 1.0×10^?6 mol/L and the detection limit is 2.0×10^?9 mol/L. Owing to low background interference of NIR measurement, the proposed method displays relative high sensitivity and selectivity. Especially, some physiologically important cations almost do not interfere with the determination of Cu²⁺. The proposed method was also applied to the determination of trace Cu²⁺ in real aqueous samples with satisfactory results.     

High Sensitivity and Reproducibility of a Bismuth/Poly(bromocresol purple) Film Modified Glassy Carbon Electrode for Determination of Trace Amount of Cadmium by Differential Pulse Anodic Stripping Voltammetry

This work described a novel type of bismuth/poly(bromocresol purple) film modified glassy carbon electrode (denoted as Bi/Poly(BCP)/GCE) for anodic stripping analysis of trace Cd²⁺. The Bi/Poly(BCP)/GCE was fabricated in situ by depositing simultaneously bismuth and cadmium by reduction at ?1.20 V on the poly(BCP) film using a differential pulse voltammetry. Under the optimum conditions, the anodic stripping peak current response increased linearly with the Cd²⁺ concentrations in a range of 2.0×10^?8–1.0×10^?7 M and 1.0×10^?7–6.0×10^?6 M in 0.1 M NaAc‐HAc buffer solution (pH 5.0) with the detection limit of 6.5×10^?9 M (S/N=3). The Bi/poly(BCP)/GCE performed good reproducibility and high sensitivity. Finally, this proposed method was successfully applied to determine the concentration of Cd²⁺ in water samples.     

Properties of Water-Soluble Porphyrin as a Sensitizer in Peroxyoxalate-Hydrogen Peroxide Chemiluminescence System and Its Application to the Quenching FluorometriC Determination of Copper(II)

ABSTRACT

Six kinds of water-soluble porphyrin were examined as a sensitizer (fluorophore) in the bis(2,4,6-trichlorophenyl)oxalate(TCPO)-hydrogen peroxide (H₂O₂) chemiluminescence(CL) system. Among them, coproporphyrin III showed the highest CL intensity. Moreover, the TCPO-H₂O₂-coproporphyrin III CL system was separately examined in each micelle solution using a non-ionic surfactant such as Briji 35 and Triton X-100, and an ionic surfactant such as cetyltrimethylammonium chloride(CTAC) and sodium dodecylsulfate. As a result, the CL intensity along with the coexistence of the CTAC micelle increased approximately 36 times compared to that in the absence of surfactant. Based on these findings, the quenching CL determination of copper(II) was established using the complex formation of coproporphyrin III and copper(II) ion. The calibration graph for the concentration of copper(II) was linear in the range of 2×10^?8M to 1×10^?6M, and the detection limit(3σ) was 1.26×10^?8M. Moreover, the relative standard deviation was 2.9%(10 determinations). The proposed method was applied to the determination of copper(II) ion in waste water and satisfactory results were obtained.