Determination of the Camptothecin Derivatives CPT-11 and SN-38 in Urine and Saliva by Micellar Electrokinectic Chromatography

The anti-cancer synthetic drug irinotecan (CPT-11) and its active metabolite SN-38 have been determined by micellar electrokinetic capillary chromatography (MEKC). The detection of the analytes was made at 368 nm and their separation took less than 7 min using a borate buffer (pH 8.8 at 25 mmol L^?1) solution containing sodium dodecyl sulfate (45 mmol L^?1) and acetonitrile (13.5% v/v). On-line analyte concentration (normal stacking mode) and the use of a highly sensitive cell (Z shaped cell) improved detection limits (at the 10^?8 mol L^?1 level). Recovery in fortified human saliva was 108 ± 5%, in agreement with the result achieved with the reference HPLC method. For the analysis of urine from rats submitted to a single dose of CPT-11 and SN-38, camptothecin was used as internal standard enabling recoveries close to 100% when compared to the results achieved using HPLC.     

Simultaneous Analysis of Sugars and Polyphenols in Tobacco by CZE with Amperometric Detection Based on a Cu2O/MWCNT-COOH Composite Electrode

A composite electrode was fabricated from Cu₂O powder, carboxyl-functionalized multi-wall carbon nanotubes (MWCNT-COOH), and paraffin oil in the proportions 51:17:32 (w/w). This composite electrode was used for amperometric detection (CZE–AD) in simultaneous capillary zone electrophoretic analysis of chlorogenic acid, rutin, sucrose, glucose, mannose, and fructose in tobacco samples. Under the optimum conditions, the six analytes could be separated in 100 mmol L^?1 NaOH buffer within 30 min. Good linearity was achieved in the range 1 × 10^?7–1 × 10^?4 mol L^?1 for the two polyphenols and 5 × 10^?6–1 × 10^?3 mol L^?1 for the four sugars. The detection limits (S/N = 3) for the polyphenols and sugars were as low as 10^?8 mol L^?1 and 10^?6 mol L^?1, respectively.     

Stripping voltammetry method for determination of manganese as complex with oxine at the carbon paste electrode with and without modification with montmorillonite clay

Oxine (8-hydroxyquinoline) was used as an efficient and selective ligand for stripping voltammetry trace determination of Mn(II). A validated square-wave adsorptive cathodic stripping voltammetry method has been developed for determination of Mn(II) selectively as oxine complex using both the bare carbon paste electrode (CPE) and the modified CPE with 7 % (w/w) montmorillonite-Na clay. Modification of carbon paste with montmorillonite clay was found to greatly enhance its adsorption capacity. Limits of detection of 45 ng l^?1 (8.19?×?10^?10 mol L^?1) and 1.8 ng l^?1 (3.28?×?10^?11 mol L^?1) Mn(II) were achieved using the bare and modified CP electrodes, respectively. The achieved limits of detection of Mn(II) as oxine complex using the modified CPE are much sensitive than the detection limits obtained by most of the reported electrochemical methods. The developed stripping voltammetry method using both electrodes was successfully applied for trace determination of Mn(II) in various water samples without interferences from various organic and inorganic species.     

Highly Sensitive Flow-Injection Chemiluminescence Detection of Carbonyl Compounds in Wine Samples

A modified Trautz–Schorigin reaction, by using tannic acid-H₂O₂ system for the oxidation and determination of two kinds of carbonyl compounds was developed in this paper. It was found that formaldehyde and acetaldehyde could effectively enhance the chemiluminescence signals of tannic acid–H₂O₂ system in alkaline medium. Under optimized conditions, the proposed method has a linear range of 7 × 10^?9–1 × 10^?4 mol L^?1 for formaldehyde and 1 × 10^?8–1 × 10^?4 mol L^?1 for acetaldehyde with detection limits of 9 × 10^?11 and 3 × 10^?10 mol L^?1, respectively. The relative standard deviations for 15 repeated measurements of 1 × 10^?6 mol L^?1 HCHO and CH₃CHO are 1.13% and 1.65%, respectively. Analysis time per sample is 35 seconds. A comparison of results found by the proposed method with those obtained by a standard reference method provided good agreement. The proposed method is simple, rapid, convenient, and sensitive.     

A Direct Chemiluminescence Method for the Determination of Prulifloxacin Using Tris-(4,7-Diphenyl-1,10-Phenanthrolinedisulfonic Acid) Ruthenium(II)–Cerium(IV) System

Abstract

A simple, rapid, injection chemiluminescence method is described for the determination of prulifloxacin, a commonly used antibiotic. A strong chemiluminescence signal was detected when a mixture of the analyte and tris-(4,7-diphenyl-1,10-phenanthrolinedisulfonic acid)ruthenium(II) was injected into cerium(IV) sulfate. The chemiluminescence signal is proportional to the concentration of prulifloxacin in the range 4.0 × 10^?8–9.0 × 10^?6 mol L^?1. The detection limit is 1.0 × 10^?8 mol L^?1, and the relative standard deviation is 2.2% (n = 11) for the determination of 8.0 × 10^?7 mol L^?1 prulifloxacin. The proposed method was successfully applied to the determination of prulifloxacin in pharmaceutical preparations in capsules, spiked serum, and urine samples.     

Removal, preconcentration and spectrophotometric determination of U(VI) from water samples using modified maghemite nanoparticles

Arsenazo III modified maghemite nanoparticles (A-MMNPs) was used for removing and preconcentration of U(VI) from aqueous samples. The effects of contact time, amount of adsorbent, pH and competitive ions was investigated. The experimental results were fitted to the Langmuir adsorption model in the studied concentration range of uranium (1.0 × 10^?4–1.0 × 10^?2 mol L^?1). According to the results obtained by Langmuir equation, the maximum adsorption capacity for the adsorption of U(VI) on A-MMNPs was 285 mg g^?1 at pH 7. The adsorbed uranium on the A-MMNPs was then desorbed by 0.5 mol L^?1 NaOH solution and determined spectrophotometrically. A preconcentration factor of 400 was achieved in this method. The calibration graph was linear in the range 0.04–2.4 ng mL^?1 (1.0 × 10^?10–1.0 × 10^?8 mol L^?1) of U(VI) with a correlation coefficient of 0.997. The detection limit of the method for determination of U(VI) was 0.01 ng mL^?1 and the relative standard deviation (R.S.D.) for the determination of 1.43 and 2.38 ng mL^?1 of U(VI) was 3.62% and 1.17% (n = 5), respectively. The method was applied to the determination of U(VI) in water samples.     

Electrooxidation of trifloxystrobin at the boron-doped diamond electrode: electrochemical mechanism,quantitative determination and degradation studies

The boron-doped diamond (BDD) presents attractive electrochemical sensing characteristics that are useful in analytical applications based on voltammetry and amperometry. It has a wide potential window in aqueous solutions enabling the quantification of the fungicide trifloxystrobin, measured at +1744 mV (versus Ag/AgCl), by square-wave anodic voltammetry in a Britton–Robinson (BR) buffer (0.04 mol L^?1; pH 4.00)/acetonitrile 70/30% v/v. The activation of the electrode was made using galvanostatic chronopotentiometry and cyclic voltammetry (CV). The linear analyte addition curve, I_p (µA) = (1.0 × 10^–1 ± 4.8 × 10^–6) C (mol L^?1) + (8.8 × 10^–2 ± 1.1 × 10^–3); R² = 0.997, was obtained using amplitude of 40 mV, frequency of 30 Hz, step potential of 20 mV. The instrumental limit of detection (LOD) was 1.4 × 10^–7 mol L^?1 (0.058 mg L^?1) and the dynamic linear range covered three decades (up to 1 × 10^–5 mol L^?1 or 4.1 mg L^?1). The samples were analysed with recoveries about 80% in orange juice samples and from 92.4% to 104.0% in water samples. A study to evaluate potential interferences was made in the presence of other fungicides. Diagnostic studies indicated that oxidation of trifloxystrobin in aqueous medium at the surface of the BDD is irreversible, involving two steps, each one with two electrons. The UV degradation of trifloxystrobin was evaluated using the proposed electrochemical method and the kinetics of degradation established with half-life of 1.07 min.     

Voltammetric determination of 17α-ethinylestradiol hormone in supply dam using BDD electrode

In this work, a simple method for electroanalytical determination of 17α-ethinylestradiol (EE2) hormone in natural waters was developed using a boron-doped diamond electrode (BDD). The analyses were performed using square wave voltammetry and the parameters were optimized. The results showed a well-defined irreversible oxidation peak (BR buffer 0.1 mol L^?1, pH 8.0) at +0.65 V (vs. Ag/AgCl). The voltammetric results showed also that the oxidation process is controlled by adsorption of species and indicated that there are two electrons involved. The obtained analytical curves for 17α-ethinylestradiol presented good linearity in the concentration range 9.9?×?10^?7 to 5.2?×?10^?6 mol L^?1 in utlrapure water and 7.9?×?10^?7 to 5.2?×?10^?6 mol L^?1 in natural water samples (supply dam). Detection limits (DL) obtained were between 2.4?×?10^?7 and 7.5?×?10^?7 mol L^?1 and quantification limits (QL) between 7.9?×?10^?7 and 2.5?×?10^?6 mol L^?1. The recovery experiments showed values between 86 and 114 % for spiked samples thus indicating the applicability of the electroanalytical methodology to quantify 17α-ethinylestradiol directly in natural water of supply Dam (Billings Dam in Diadema-SP. Brazil), without any preconcentration or derivatization.     

Magnetic nanoparticles grafted with β-cyclodextrin for solid-phase extraction of 5-hydroxy-3-indole acetic acid

We describe the synthesis of ß-cyclodextrin modified magnetic nanoparticles (CD-mNPs) as a material for solid-phase extraction of the cancer biomarker 5-hydroxy-indole-3-acetic acid (5-HIAA) from urine. The CD-mNPs were characterized by TEM, FTIR, and XRD, and the kinetics and adsorption isotherms were studied. The strong interaction between the CD-mNPs and 5-HIAA is the main driving force for recognition and extraction, while the magnetic core of the NPs allows their separation from the sample matrix. Recovery of 5-HIAA from the adsorbent using an adequate solvent regenerated the adsorbent for further use. 5-HIAA was then quantified by fluorometry of its complex with ß-CD. The method works in the 1?×?10^?7 to 1?×?10^?5 mol L^?1 (R² 0.9982–0.9996) concentration range, and the limits of detection (3σ) and quantification (10 σ) of the method are 1.2?×?10^?8 mol L^?1 and 4.01?×?10^?8 mol L^?1 5-HIAA, respectively. The recovery of 5-HIAA from urine samples spiked with 5-HIAA in three concentrations (1.4?×?10^?6, 4.50?×?10^?6 and 1.0?×?10^?5 mol L^?1) are within 63?±?3 %.

Ion-selective carbon paste electrode based on new tripodal ligand for determination of cadmium (II)

A new chemically modified carbon paste electrode for Cd(II) ions based on 3,5-dinitro-N-(tri-2-pyridyl methyl) benzamide (DNTPMBA) as an ionophore was prepared. The electrode exhibits a Nernstian response for Cd(II) ions over a wide concentration range (2.16 × 10^?7–1.00 × 10^?1 mol L^?1) with a slope of 30 ± 1 mV per decade. It has a response time of about 50 s and can be used for a period of 3 months with good reproducibility. Detection limit obtained in the optimal conditions was 1.82 × 10^?7 mol L^?1. The electrode was successfully used for potentiometric determination of Cd(II) in well water. The pH influence and interference of some cations were also studied.     

Solid Phase Extraction and High Performance Liquid Chromatography for Determination of Glyoxylic Acid in a Selective Oxidation Reaction

Currently, the development of a new method for the analysis of glyoxylic acid in selective oxidation of glyoxal system has become a key subject in its new industrial process development. Since solid phase extraction (SPE) could isolate and concentrate desired analytes from complex matrices, in this paper we tested the possibility of coupling SPE technique with HPLC for simultaneous determination of glyoxylic acid, formic acid, and oxalic acid in this complex chemical reaction system. Results demonstrated that the developed method could be successfully applied to this system, after samples were passed through SAX cartridges and yielded recoveries from 96.7% to 103%. The limits of detection were 2.6 × 10^?6, 3.6 × 10^?6, and 3.5 × 10^?7 mol L^?1, respectively; and their linear ranges between 1 × 10^?6 and 1 × 10^?2 mol L^?1.     

Determination of Sodium Hexametaphosphate in Beverages Based on the Fluorescence Quenching of Acridine Orange

Sodium hexametaphosphate was shown to form a complex with acridine orange by electrostatic interactions that induce fluorescence quenching. Analysis of fluorescence intensity showed that the process was dominated by static quenching, which was confirmed by absorption spectra and lifetime of the excited state. The decreased fluorescence intensity was directly proportional to the concentration of sodium hexametaphosphate between 8.0 × 10^?7 and 1.1 × 10^?5 mol L^?1 with a limit of detection of 5.3 × 10^?7 mol L^?1. Beverages were analyzed for sodium hexametaphosphate with recoveries between 91.7% and 108.3%.     

Determination of Polyethylene Glycol Monoester Acrylate and Polyethylene Glycol Diester Acrylate Using Reversed-Phase High-Performance Liquid Chromatography

A procedure was developed for the determination of polyethylene glycol monoester acrylate (PEGMA) and polyethylene glycol diester acrylate (PEGDA) by reversed-phase high performance liquid chromatographic (RP-HPLC) with UV detector. Sample was well separated on an SinoChrom ODS-BP (C-18) column (200 × 4.6 mm i.d., 5 μm) with mobile phases composed of acetonitrile-phosphate buffer solution (0.05 mol · L^?1 pH = 6.86) in the ratio of 42:58 (v/v). The PEGMA and PEGDA were detected by UV detector at 205 nm, and quantitatively analyzed with an external standard of methyl acrylate. For PEGMA, the linear response ranged from 0.40 × 10^?5 mol · L^?1 to 2.00 × 10^?3mol · L^?1 (r² > 0.999), the detection limit was 0.12 × 10^?5 mol · L^?1, the recovery rate was found to be 93.4%–99.7%. For PEGDA, the linear response ranged from 0.20 × 10^?5 mol · L^?1 to 1.00 × 10^?3mol · L^?1 (r² > 0.999), the detection limit was 0.04 × 10^?5 mol · L^?1, the recovery rate was found to be 99.1% ～ 105.8%. This quantitative method can also be used in the HPLC analysis of other α,β-unsaturated esters.     

Flow Injection Spectrophotometric Determination of N-Acetylcysteine and Captopril Employing Prussian Blue Generation Reaction

A novel flow injection procedure to determine N-acetylcysteine and captopril in pharmaceutical formulations is proposed. The flow procedure developed was based on oxidation of the analytes by Fe(III) in acidic medium and subsequent reaction of the Fe(II) generated with excess hexacyanoferrate(III) to produce soluble Prussian blue (KFe[Fe(CN)₆]) measured at 700 nm. Detection limits of 1.0 × 10^?5 mol L^?1 and 3.0 × 10^?5 mol L^?1 for N-acetylcysteine and captopril, respectively, were found. The sample throughput was 70 h^?1 for both analytes and the results obtained were in agreement at a 95% confidence level with those obtained using reference methods.     

Fabrication of a new nanocomposite modified carbon paste Al<Superscript>3+</Superscript>-ion selective electrode based on <Emphasis Type="Italic">N,N</Emphasis>′-dipyridoxyl (1,2-cyclohexanediamine) (PYCA) as an active material

Construction and feature of a nanocomposite modified carbon paste electrode for aluminum(III) ion determination based on N,N′-dipyridoxyl (1,2-cyclohexanediamine) (PYCA) as a novel selector material will be covered by this paper. The optimum composition, Nernstian slope/linear range/detection limit in the forms of calibration graph, response time, utilizable pH range, repeatability and precision of measurements of the aluminum(III) ion using the new fabricated Al³⁺-CPE was evaluated. The optimal composition which performed over Al⁺³ ion concentration range 1.0 × 10^?8 mol L^?1–1.0 × 10^?1 mol L^?1 with near-Nernstian slope equal 20.9 ± 0.2 mV decade^?1 and low detection limit about 5.0 × 10^?9 mol L^?1, was formed of ionophore (PYCA 3 %), binder (paraffin oil 30 %), modifier [multi-wall carbon nanotubes (MWCNTs) 1 %] & [Nanosilica (NS) 0.5 %], and inert matrix (graphite powder 65.5). The request time to give rise Nernstian response of electrode for concentrations from 1.0 × 10^?8 mol L^?1 to 1.0 × 10^?1 mol L^?1 of Al³⁺ ion solution was estimated about ~6 s. The new Al³⁺-CPE was applied in pH range 2.0–5.0 with no consequential change in potential response. To verify the selectivity of electrode toward aluminum(III) ion in the presence of different metallic cations, matched potential method was used. The obtain results in analytical applications reflect the excellent ability of this electrode to play the role as endpoint indicator electrode in both titration and direct potentiometric measurements.     

Selective Determination of Harmol by Room-Temperature Phosphorimetry: A Comparative Performance with Micellar Electrokinetic Capillary Chromatography

Abstract

Selective determination of harmol in the presence of other β-carboline alkaloids without the need for previous separation of components was achieved by Solid Surface Room-Temperature Phosphorimetry (SSRTP) using HgCl₂. Detection of harmol at concentrations as low as 5.2 × 10^?7 mol L^?1 can be made in urine samples. Recovery of 100±12% was achieved. The analytical performance of SSRTP was compared to Micellar Electrokinetic Capillary Chromatography (MECC).     

Green Spectrophotometric Method for the Quantitative Analysis of Vancomycin in Pharmaceuticals and Comparison with HPLC

Abstract

A spectrophotometric method for the determination of vancomycin base, (VCM), and vancomycin hydrochloride, (HVCM), based on the reaction with copper (II) ions, is presented. The obtained detection limit is about 4.5×10^?5 mol L^?1. The working analytical range falls between 1.0×10^?3 mol L^?1 and 1.0×10^?2 mol L^?1. Recovery studies in presence of excipients were performed. The recovery results were compared with HPLC. For HVCM the proposed method presented similar recovery to that of HPLC, 100.4% vs. 100.2%, but better precision, 1.9% vs. 6.1%. In the VCM case the recovery is quite better, 100.5% vs. 89.6%, with a little smaller precision, 2.1% vs. 1.3%.     

Simple and fast voltammetric procedure of U(VI) determination in the presence of high concentrations of surface active substances

In this work, a simple and fast procedure for elimination of interfering surface active substances and for U(VI) adsorptive stripping voltammetric determination was developed. The adsorption in the form of U(VI)-cupferron complexes was performed, because as it was proved before, U(VI) forms with cupferron stable complexes, which were employed in voltammetric procedures. The procedure is based on two steps: the first is an adsorption of surface active substances onto an Amberlite XAD-16 or XAD-7 resin and the second is a voltammetric determination of U(VI) with a pulsed potential of accumulation alternate –0.65–0.3 V with the frequency of 0.5 Hz and then the differential pulse voltammogram was recorded, whereas the potential was scanned from –0.65 to –1.2 V. The detection limit estimated from three times the standard deviation for a low U(VI) concentrations was equal to 1.7 × 10^?10 mol L^?1 (7.2 × 10^?8 g L^?1). The linear range of U(VI) was observed over the concentration range from 5.0 × 10^?10 mol L^?1 (2.1 × 10^?7 g L^?1) to 2.0 × 10^?8 mol L^?1 (8.5 × 10^?6 g L^?1) for an accumulation time of 60 s. The influence of different kinds of surfactants, such as non-ionic, cationic and anionic on the uranium voltammetric signal was studied. The results confirm the possibility of U(VI) determination in water samples containing high concentrations of surface active substances even up to 50 mg L^?1.     

Preparation and characterization of in situ carbon paste and screen-printed potentiometric sensors for determination of econazole nitrate: surface analysis using SEM and EDX

The construction and performance characteristics of new sensitive and selective in situ carbon paste (ICPE) and screen-printed (ISPE) potentiometric sensors modified with ion-pairing agents such as phosphotungstic acid, sodium tetraphenylborate, phosphomolybdic acid and ammonium reineckate for determination of econazole nitrate (ECN) have been developed. The reaction mechanism between ECN and ion-pairing agents at the electrode surface was studied through scanning electron microscope and energy-dispersive X-ray analysis. The electrodes under investigation showed potentiometric response for ECN in the concentration range from 1.0 × 10^?6 to 5.0 × 10^?3 mol L^?1 and from 1.0 × 10^?6 to 1.0 × 10^?2 mol L^?1 for ISPE (electrode I) and ICPE (electrode II) potentiometric sensors, respectively, at 25 °C. The electrode response was pH independent in the range 2.5–7.5 and 2.5–6.5 for electrodes I and II, respectively. These sensors have Nernstian slope values of 59.4 ± 0.2 and 59.10 ± 0.2 mV decade^?1 with detection limit of 1.0 × 10^?6 mol L^?1 for electrodes I and II, respectively. The electrodes showed fast response time of 4 and 9 s for electrodes I and II, respectively. The ISPE (electrode I) showed lifetime of 28 days, and this was considered as advantage over ICPE (electrode II). Selectivity for ECN with respect to a number of interfering materials was also investigated. The proposed electrodes were applied for determination of ECN in pure and pharmaceutical formulation using calibration, potentiometric titration and standard addition methods. The results showed good agreement with those obtained using official method. The t and F values indicated no significant difference between the suggested and reported methods. Method validation parameters were optimized according to ICH recommendations.     

Determination of lead(II) in aqueous solution using carbon nanotubes paste electrodes modified with Amberlite IR-120

A new composite electrode is described for anodic stripping voltammetry determination of Pb(II) at trace level in aqueous solution. The electrode is based on the use of multiwalled carbon nanotubes and Amberlite IR-120. The anodic stripping voltammograms depend, to a large extent, on the composition of the modified electrode and the preconcentration conditions. Under optimum conditions, the anodic peak current at around ?0.57 V is linearly related to the concentration of Pb(II) in the range from 9.6?×?10^?8 to 1.7?×?10^?6 mol L^?1 (R?=?0.998). The detection limit is 2.1?×?10^?8 mol L^?1, and the relative standard deviation (RSD) at 0.24?×?10^?6 mol L^?1 is 1.7% (n?=?6). The modified electrode was applied to the determination of Pb(II) using the standard addition method; the results showed average relative recoveries of 95% for the samples analysed.