The cathodic stripping voltammetric determination of traces of iodide with a hanging copper amalgam drop electrode

A hanging copper amalgam drop electrode (HCADE) is used for the determination of traces of iodide by cathodic stripping voltammetry. The cathodic stripping peak of copper(I) iodide from the HCADE is better defined than that of mercury(I) iodide from a hanging mercury drop electrode. Optimum conditions and interferences are reported. With a 3-min deposition time at ?0.1 V vs. SCE, the calibration plot is linear up to 2 × 10^?6 mol dm^?3 iodide. The detection limit for iodide with the HCADE under voltammetric conditions is 4 × 10^?8 mol dm^?3; this is lowered to 8 × 10^?9 mol dm^?3 by using the differential pulse stripping technique.     

Subnanomolar Determination of Indium by Adsorptive Stripping Differential Pulse Voltammetry Using Factorial Design for Optimization

Abstract

A highly sensitive method to determine of indium is proposed by adsorption stripping differential pulse cathodic voltammetry (AdSDPCV) method. The complex of indium ions with xylenol orange is analyzed based on the adsorption collection onto a hanging mercury drop electrode (HMDE). After accumulation of the complex at ?0.20 V vs. Ag/AgCl reference electrode, the potential is scanned in a negative direction from ?0.40 to ?0.75 V with the differential pulse method. Then, the reduction peak current of In(III)–XO complex is measured. The influence of chemical and instrumental variables was studied by factorial design analysis. Under optimum conditions and accumulation time of 60 s, linear dynamic range was 0.1–10 ng/ml (8.7 × 10^?10 to 8.7 × 10^?8 M) with a limit of detection of 0.03 ng/ml (2.6 × 10^?10 M); at accumulation time of 5 min, linear dynamic range was 0.04–10 ng/ml (3.4 × 10^?10 to 8.7 × 10^?8 M) with a limit of detection of 0.013 ng/ml (1.1 × 10^?10 M). The applicability of the method to analysis of real samples was assessed by the determination of indium in water, alloy, and jarosite (zinc ore) samples.     

Adsorptive Stripping Voltammetric Determination of Albendazole at a Hanging Mercury Drop Electrode

ABSTRACT

Albendazole is determined by differential-pulse adsorptive cathodic stripping voltammetry at a hanging mercury drop electrode using the reduction peak of its copper(II) complex at ?0.28V at an accumulation potential 0.0V vs. Ag/AgCl electrode. The optimum conditions of pH, accumulation potential and accumulation time were studied. The calibration graph for the determination of albendazole was linear in the range 3.0X10^?8 - 9X10^?7M with a relative standard deviation of 2.8%. The detection limit was 1.0X10^?8M after 180s accumulation at 0.0V. The effect of common excipients and metal ions on the peak height of albendazole was studied. The presence of Cu²⁺ ions forms a stable complex with albendazole which is strongly adsorbed at the mercury electrode surface. The method was applied to the determination of the drug in commercially available dosage forms.     

Sequential extraction partitioning of metals,sulfur, and phosphorus in bottom ash from a coal-fired power plant

Abstract

The herbicide trifluralin was analysed by adsorptive stripping voltammetry on a glassy carbon electrode. The linear concentration range was 2.5 × 10^?7 M – 1.25 × 10^?6M when using 5-min preconcentration at open circuit conditions in Britton-Robinson buffer of pH 7.0. The detection limit of trifluralin was 2.5 × 10^?8M. The relative standard deviation was 3.3% at a concentration of 1.0 × 10^?6M (n=5). The method was applied to the determination of trifluralin in soil with good recovery.     

Adsorptive Cathodic Stripping Voltammetry Determination of Ultra Trace of Lead in Different Real Samples

Abstract

In the present work, an adsorptive cathodic stripping voltammetric method using a hanging mercury drop electrode (HMDE) was described in order to determine the ultra trace of lead ions with carbidopa in different real samples. The method is based on accumulation of lead metal ion on mercury electrode using carbidopa as a suitable complexing agent. The potential was scanned to the negative direction and the differential pulse stripping voltammograms were recorded. The instrumental and chemical parameters were optimized. The optimized conditions were obtained in pH of 8.4, carbidopa amount of 1.0×10^?6 M, accumulation potential of 0. 0 V, accumulation time of 100 s, scan rate of 100 mV/s and pulse height of 50 mV. The relationship between the peak current versus concentration was linear over the range of 2.4×10^?10–4.8×10^?7 M. The limits of detection were 5.8×10^?11 M and the relative standard deviation at 4.8×10^?10, 2.1×10^?8, and 2.4×10^?7 M of lead ion were obtained 3.2, 2.9, and 2.7%, respectively (n=7).     

Electrochemical Behavior of 6-Mercapto-Purine at Hanging Copper Amalgam Dropping Electrode and Its Trace Determination by Differential Pulse Adsorption Cathodic Stripping Voltammetry

Abstract

The electrochemical behavior of 6-MP was studied by cyclic voltammetry at a hanging copper amalgam dropping electrode (HCADE). It was found that 6-MP could form a complex with the Cu(II) stripped from the HCADE, showing a new peak at ?0.19V in the medium of 0.1mol/L LiClO₄-0.5mol/L HClO₄ solution. The mechanism of the reaction was proposed. This new peak was sensitive and could be used for the determination of trace 6-MP by differential pulse adsorption cathodic stripping voltammetry (DPAdCSV). The linear range was from 3.6×10^?10 to 5.3×10^?6 mol/L, and the detection limit was about 1.2×10^?10 mol/L (S/N=3). The method was also successfully applied to the determination of 6-MP in pharmaceutical tablets.     

Simultaneous Determination of Antimony and Lead in Gunshot Residue by Cathodic Adsorptive Stripping Voltammetric Methods

Differential pulse cathodic adsorptive stripping (DPCAdSV) and square wave cathodic adsorptive stripping (SWCAdSV) voltammetric methods were developed for the determination of antimony and lead in gunshot residues. Linear working ranges for DPCAdSV and SWCAdSV methods were (2.0×10^?9–5.0×10^?7) M and (2.0×10^?9–7.0×10^?7) M for antimony and 2.0×10^?9–3.0×10^?7 M (both methods) for lead. The detection of antimony limits were found to be 1.3×10^?9 M for DPCAdSV and 7.3×10^?10 M for SWCAdSV while the corresponding values for lead were 3.0×10^?9 M and 5.8×10^?10 M. Antimony and lead contents obtained by these methods in gunshot residues are in good agreement with those obtained by graphite furnace atomic absorption spectrometric method within a confidence limit of 95%.     

Electrochemical Oxidation and Determination of Theophylline at a Carbon Paste Electrode Using Cetyltrimethyl Ammonium Bromide as Enhancing Agent

Abstract

The oxidation of theophylline was studied at a carbon paste electrode in the presence of cetyltrimethyl ammonium bromide by cyclic and differential pulse voltammetry. The results indicated that the electrochemical responses of theophylline are apparently improved by cetyltrimethyl ammonium bromide, due to the enhanced accumulation of theophylline at carbon paste electrode surface. Under optimal conditions the peak current was proportional to theophylline concentration in the range of 8.0 × 10^?7 to 2.0 × 10^?4 M with a detection limit of 1.85 × 10^?7 M by differential pulse voltammetry. The proposed method was applied to the determination of theophylline in tablet and urine samples.     

Investigations on Bioanalytical Chemistry Part I. On Differential Pulse Voltammetry of Bilirubin

Abstract

The electrochemical behaviour of the bilirubin in many kinds of supporting electrolytes on a glassy carbon electrode (GCE) and a hanging mercury drop electrode (HMDE) was investigated by means of anodic or cathodic differential pulse voltammetry. The influences of different methods of pre-treatment of the glassy carbon electrode was also discussed. In Na₂B₄.O₇-KH₂PO₄ buffer solution, the linear range was 2×10^?9-1×10^?9 mol/l and the detection limit was 3.3×10^?9 mol/l by anodic differential pulse voltammetry at GCE. A linear relationship holds between the peak current and the concentration of bilirubin in a concentration range of 1×10^?9-4×10^?7 mol/l with good precision and accuracy, and the limit of detection was 2×10^?10 mol/l, when cathodic differential pulse adsorption voltammetry at HMDE was used.     

Square-Wave Cathodic Stripping Voltammetry of Marcellomycine. A Sensitive Analytical Method

Abstract

Square-wave adsorptive stripping voltammetry has been applied to the determination of a new cytostatic anthracyclinic compound, marcellomycine. 100-fold and 1000-fold increases of sensitivity have been found with regard to the differential pulse stripping voltammetry and differential pulse polarography respectively. The detection limit is fixed at 5 × 10^?9 M.     

A polarographic and voltammetric study of some primary,secondary and tertiary thioamides of pharmaceutical importance

The d.c. polarographic, and cyclic and cathodic stripping voltammetric behaviour of some primary, secondary and tertiary thioamides based on tetrahydroquinoline, is described. Catalytic reduction occurs in all cases; the primary and secondary thioamides undergo anodic oxidation and cathodic stripping, with the formation of mercury(II) sulphide. Tertiary thioamides are not amenable to anodic electrolysis/stripping. Mechanisms for these oxidation and reduction processes are postulated. Differential pulse polarography has a limit of detection of 5 × 10^?7 M. Cathodic stripping voltammetry can be applied with a detection limit of 2 × 10^?8 M.     

Electrochemical Studies and Square‐Wave Adsorptive Stripping Voltammetry of Spironolactone Drug

Abstract

A sensitive and reliable stripping voltammetric method was developed to determine Spironolactone drug. This method is based on the adsorptive accumulation of the drug at a hanging mercury drop electrode and then a negative sweep was initiated, which yield a well defined cathodic peak at ?1000 mV versus Ag/AgCl reference electrode. To achieve high sensitivity, various experimental and instrumental variables were investigated such as supporting electrolyte, pH, accumulation time and potential, drug concentration, scan rate, frequency, pulse amplitude, convection rate and working electrode area. The monitored adsorptive current was directly proportional to the concentration of Spironolactone and it shows a linear response in the range from 1×10^?8 to 2.5×10^?7 mol l^?1 (correlation coefficient=0.999) and the detection limit (S/N=3) is 1.72×10^?10 mol l^?1 at an accumulation time of 90 sec. The developed AdSV procedure shows a good reproducibility, the relative standard deviation RSD% (n=8) at a concentration level of 1.5×10^?7 mol l^?1 was 1.4%, whereas the method accuracy was indicated via the mean recovery of 97.5%±2.04. Possible interferences by several substances usually present in the pharmaceutical formulations have been also evaluated. The applicability of this approach was illustrated by the determination of Spironolactone in pharmaceutical preparation and biological fluids such as serum and urine.     

Determination of folic acid by adsorptive stripping voltammetry at the static mercury drop electrode

Folic acid can be determined at nanomolar concentrations by controlled adsorptive accumulation of folic acid on a static mercury drop electrode held at ?0.3 V vs. Ag/AgCl followed by reduction of the surface species. In 0.1 M sulfuric acid, a cathodic scan gives peaks at ?0.47 v and ?0.75 V vs. Ag/Agcl; the latter peak provides greater sensitivity. Differential-pulse stripping is shown to be superior to normal-pulse and d.c. stripping. After a 5-min preconcentration, the detection limit is about 1 × 10^?10 M folic acid. The adsorptive stripping response is evaluated with respect to concentration dependence, preconcentration time and potential, solution acidity and the presence of gelatin and bromide. The relative standard deviation at the 5 × 10^?8 M level is 1.2%. This method is applied to the determination of folic acid in pharmaceutical tablets.     

Voltammetric sensing of triclosan in the presence of cetyltrimethylammonium bromide using a cathodically pretreated boron-doped diamond electrode

ABSTRACT

In the present study, a simple, cheap and sensitive electrochemical method based on a cathodically pretreated boron-doped diamond (CPT-BDD) electrode is described for the detection of triclosan with the cationic surfactant (cetyltrimethylammonium bromide, CTAB) media. The oxidation of triclosan was irreversible and exhibited an adsorption controlled process. The sensitivity of the adsorptive stripping voltammetric measurements was significantly improved with addition of CTAB. Using square-wave stripping mode, a linear response was obtained for triclosan determination in Britton-Robinson buffer solution at pH 9.0 containing 2.5 × 10^?4 M CTAB at around + 0.67 V (vs. Ag/AgCl) (after 30 s accumulation at open-circuit condition). The method could be used in the range of 0.01–1.0 μg mL^?1 (3.5 × 10^?8–3.5 × 10^?6 M), with a detection limit of 0.0023 μg mL^?1 (7.9 × 10^?9 M). The feasibility of the proposed method for the determination of triclosan in water samples was checked in spiked tap water.     

Determination Of Nucleic Acid Bases At Nanomolar Concentrations By Means Of Cathodic Stripping Voltammetry

Abstract

It is shown that nucleic acid bases and some of their derivatives can be determined by means of cathodic stripping voltammetry (CSV). The limit of detection of adenine is about 2 × 10^?9 M. Presence of an excess of DNA does not interfere with the determination of free bases. CSV may be used also for the determination of nucleosides and nucleotides derived from purine bases.     

Fabrication of Bismuth/Multi-walled Carbon Nanotube Composite Modified Glassy Carbon Electrode for Determination of Cobalt

A bismuth/multi‐walled carbon nanotube (Bi/MWNT) composite modified electrode for determination of cobalt by differential pulse adsorptive cathodic stripping voltammetry is described. The electrode is fabricated by potentiostatic pre‐plating bismuth film on an MWNT modified glassy carbon (GC) electrode. The Bi/MWNT composite modified electrode exhibits enhanced sensitivity for cobalt detection as compared with the bare GC, MWNT modified and bismuth film electrodes. Numerous key experimental parameters have been examined for optimum analytical performance of the proposed electrode. With an adsorptive accumulation of the Co(II)‐dimethylglyoxime complex at ?0.8 V for 200 s, the reduction peak current is proportional to the concentration of cobalt in the range of 4.0×10^?10?1.0×10^?7 mol/L with a lower detection limit of 8.1×10^?11 mol/L. The proposed method has been applied successfully to cobalt determination in seawater and lake water samples.     

Voltammetric Determination of L‐Dopa Using a Carbon Nanotubes‐Nafion Modified Glassy Carbon Electrode

Abstract

A method for determination of L‐dopa by the adsorption stripping voltammetry (ASV) using a multiwalled carbon nanotubes (MWNTs)–Nafion modified glassy carbon electrode (GMGCE) was proposed. This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed and the anodic peak potential is ca. 0.374V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of L‐dopa in samples. There is a good linear relationship between the peak current (i_p) and L‐dopa concentration in the range of 3.5×10^?7～1.5×10^?5 mol/L, with the limit of detection 5.0×10^?8 mol/L.     

Nafion‐Modified Glassy Carbon Electrode for Trace Determination of Indium

Abstract

A new method for determination of trace indium is proposed by the adsorption stripping voltammetry (ASV) using a Nafion‐modified glassy carbon electrode (NMGCE). This chemically modified electrode (CME) shows a better stability. A sensitive oxidation peak was observed, and the anodic peak potential is ca. ?0.548 V (vs. SCE). The influences of various experimental parameters on the current peak were completely studied. Under the optimized condition, the method has been applied to the determination of indium in water samples. There is a good linear relationship between the peak current (i_p) and indium(III) concentration in the range of 1.0×10^?9–1.0×10^?7 mol/l, and the limit of detection is 7.5×10^?10 mol/l.     

Electrochemical Behavior of Hydroquinone at Poly (Acridine Orange)–Modified Electrode and Its Separate Detection in the Presence of o‐Hydroquinone and m‐Hydroquinone

Abstract

Poly (acridine orange) (PAO) film–modified electrode was prepared by the electrooxidation of Acridine orange on a glassy carbon electrode (GCE) for the detection of hydroquinone in the presence of o‐hydroquinone and m‐hydroquinone. The electrochemical behavior of hydroquinone on the modified electrode was investigated with respect to different solution acidity, scan rate, and accumulation time. A pair of sharp and well‐defined peaks was obtained at 0.45 and 0.42 V [vs. a saturated calomel electrode (SCE)] at the PAO film–modified electrode. The potential difference between this pair of cathodic and anodic peaks was decreased to only 30 mV as compared to the 241 mV that was obtained on the bare glassy carbon electrode (GCE). As to o‐hydroquinone and m‐hydroquinone, their corresponding oxidation peaks appeared at 0.55 V and 0.89 V (vs. SCE), respectively. The oxidation potential differences between these three isomers enabled the separate detection of hydroquinone. Under the optimum experimental situation, the oxidation peak current of hydroquinone was proportional to the concentration at the range of 6.8×10^?7–9.6×10^?5 M. The detection limit was been estimated as 3×10^?7 M with 130 s accumulation. This method was applied to the hydroquinone detection in tap water samples.     

Determination of Atrazine in Natural Water Samples by Differential Pulse Adsorptive Stripping Voltammetry Using a Bismuth Film Electrode

A new method using differential pulse adsorptive stripping voltammetry for the determination of atrazine (ATZ) in natural water samples using a bismuth film electrode (BiFE) is proposed. The calibration curve was linear in the atrazine concentration range from 6.7×10^?7 to 2.0×10^?5 mol L^?1, with a limit of detection (LOD) of 1.4×10^?7 mol L^?1. The proposed electrode was applied for atrazine determination with satisfactory results compared with a high‐performance liquid chromatography method (HPLC).