Preparation and characterization of in situ carbon paste and screen-printed potentiometric sensors for determination of econazole nitrate: surface analysis using SEM and EDX

The construction and performance characteristics of new sensitive and selective in situ carbon paste (ICPE) and screen-printed (ISPE) potentiometric sensors modified with ion-pairing agents such as phosphotungstic acid, sodium tetraphenylborate, phosphomolybdic acid and ammonium reineckate for determination of econazole nitrate (ECN) have been developed. The reaction mechanism between ECN and ion-pairing agents at the electrode surface was studied through scanning electron microscope and energy-dispersive X-ray analysis. The electrodes under investigation showed potentiometric response for ECN in the concentration range from 1.0 × 10^?6 to 5.0 × 10^?3 mol L^?1 and from 1.0 × 10^?6 to 1.0 × 10^?2 mol L^?1 for ISPE (electrode I) and ICPE (electrode II) potentiometric sensors, respectively, at 25 °C. The electrode response was pH independent in the range 2.5–7.5 and 2.5–6.5 for electrodes I and II, respectively. These sensors have Nernstian slope values of 59.4 ± 0.2 and 59.10 ± 0.2 mV decade^?1 with detection limit of 1.0 × 10^?6 mol L^?1 for electrodes I and II, respectively. The electrodes showed fast response time of 4 and 9 s for electrodes I and II, respectively. The ISPE (electrode I) showed lifetime of 28 days, and this was considered as advantage over ICPE (electrode II). Selectivity for ECN with respect to a number of interfering materials was also investigated. The proposed electrodes were applied for determination of ECN in pure and pharmaceutical formulation using calibration, potentiometric titration and standard addition methods. The results showed good agreement with those obtained using official method. The t and F values indicated no significant difference between the suggested and reported methods. Method validation parameters were optimized according to ICH recommendations.     

Flow-Injection Spectrophotometric Determination of Oxalate,Citrate and Tartrate Based on Photochemical Reactions

Abstract

A flow-injection configuration for the spectrophotometric determination of oxalate, citrate and tartrate is proposed. The procedure is based on the photochemical decomposition of the complexes formed between iron(III) and these anions. The iron(II) produced in the photochemical reactions was detected by measuring the absorbance after complexation with ferrozine (λ_max=562 nm). Linear calibration graphs were obtained over the concentration ranges 5.0 × 10^?6 - 1.0 × 10^?4 M, 8 × 10^?6 - 1.8 × 10^?4 M and 1.0 × 10^?6 - 2 × 10^?5 M for oxalate, citrate and tartrate, respectively. The relative standard deviations at the 1x10^?5 M concentration level were within the range 1.29 - 1.47 %. The sampling frequency was about 40 samples h^?1. The usefulness of the method was tested in the determination of oxalate in urine and spinach, of citrate in pharmaceuticals and soft drinks and of tartrate in pharmaceuticals. For the determination of oxalate in urine samples a prior separation of the analyte by precipitation with calcium chloride is recommended.     

Novel Polymeric Membrane Sensors Based on Mn(III) Porphyrin and Co(II) Phthalocyanine Ionophores for Batch and Flow Injection Determination of Azide

Two novel potentiometric azide membrane sensors based on the use of manganese(III)porphyrin [Mn(III)P] and cobalt(II)phthalocyanine [Co(II)Pc] ionophores dispersed in plasticized poly(vinyl chloride) PVC matrix membranes are described. Under batch mode of operation, [Mn(III)P] and [Co(II)Pc] based membrane sensors display near‐ and sub‐Nernstian responses of ?56.3 and ?48.5 mV decade^?1 over the concentration ranges 1.0×10^?2?2.2×10^?5 and 1.0×10^?2?5.1×10^?5 mol L^?1 azide and detection limits of 1.5×10^?5 and 2.5×10^?5 mol L^?1, respectively. Incorporation of both membrane sensors in flow‐through tubular cell offers sensitive detectors for flow injection (FIA) determination of azide. The intrinsic characteristics of the [Mn(III)P] and [Co(II)Pc] based detectors in a low dispersion manifold show calibration slopes of ?51.2 and ?33.5 mV decade^?1 for the concentration ranges of 1.0×10^?5?1.0×10^?2 and 1.0×10^?4?1.0×10^?2 mol L^?1 azide and the detection limits are1.0×10^?5 and 3.1×10^?5 mol L^?1, respectively. The detectors are used for determining azide at an input rate of 40–60 samples per hour. The responses of the sensors are stable within ±0.9 mV for at least 8 weeks and are pH independent in the range of 3.9?6.5. No interferences are caused by most common anions normally associated with azide ion.     

A Novel Screen-Printed and Carbon Paste Electrodes for Potentiometric Determination of Uranyl(II) Ion in Spiked Water Samples

Four new ion-selective electrodes (ISEs) based on poly-(1-4)-2-amino-2-deoxy-β-D-glucan (chitosan) ionophore were constructed for determination of uranyl ion (UO₂(II)) over wide concentration ranges. The linear concentration range for carbon paste electrodes (CPEs) was 1 × 10^–6–1 × 10^–2 mol/L with a detection limit of 1 × 10^–6 mol/L and that for the screen-printed electrode (SPEs) was 1 × 10^–5–1 × 10^–1 mol/L with a detection limit of 8 × 10^–6 mol/L. The slopes of the calibration graphs were 29.90 ± 0.40 and 29.10 ± 0.60 mV/decade for CPEs with dibutylphthalate (DBP) (electrode I) and o-nitrophenyloctylether (o-NPOE) (electrode II) as plasticizers, respectively. Also, the SPEs showed good potentiometric slopes of 29.70 ± 0.30 and 28.20 ± 1.20 mV/decade with DBP (electrode III) and o-NPOE (electrode IV), respectively. The electrodes showed stable and reproducible potential over a period of 54, 62, 101 and 115 days for electrodes I, II, III, and IV, respectively. The electrodes manifested advantages of low resistance, very fast response and, most importantly, good selectivities relative to a wide variety of other cations except Ce(III) ion which interfere seriously. The results obtained compared well with those obtained using atomic absorption spectrometry.     

Construction and characterization of nano iron complex ionophore for electrochemical determination of Fe(III) in pure and various real water samples

Electrochemical methods represent an important class of widely used techniques for the detection of metal ions. The unique chemical and physical properties of nanoparticles make them extremely suitable for designing new and improved sensing devices, especially electrochemical sensors and biosensors. This study focused on the synthesis of a nano‐Fe(III)–Sud complex and its characterization using various spectroscopic and analytical tools, optimized using the density functional theory method, screened for antibacterial activity and evaluated for possible binding to DNA using molecular docking study. Proceeding from the collected information, nano‐Fe(III)–Sud was used further for constructing carbon paste and screen‐printed ion‐selective electrodes. The proposed sensors were successfully applied for the determination of Fe(III) ions in various real and environmental water samples. Some texture analyses of the electrode surface were conducted using atomic force microscopy. At optimum values of various conditions, the proposed electrodes responded towards Fe(III) ions linearly in the range 2.5 × 10^?9–1 × 10^?2 and 1.0 × 10^?8–1 × 10^?2 M with slope of 19.73 ± 0.82 and 18.57 ± 0.32 mV decade^?1 of Fe(III) ion concentration and detection limit of 2.5 × 10^?9 and 1.0 × 10^?8 M for Fe(III)–Sud‐SPE (electrode I) and Fe(III)–Sud‐CPE (electrode II), respectively. The electrode response is independent of pH in the range 2.0–7.0 and 2.5–7.0, with a fast response time (4 and 7 s) at 25°C for electrode I and electrode II, respectively. Moreover, the electrodes also showed high selectivity and long lifetime (more than 6 and 3 months for electrode I and electrode II, respectively). The electrodes showed good selectivity for Fe(III) ions among a wide variety of metal ions. The results obtained compared well with those obtained using atomic absorption spectrometry.     

Enantioanalysis of S-Ketoprofen Using Enantioselective,Potentiometric Membrane Electrodes

Abstract

Maltodextrins with different dextrose equivalent (DE) values (maltodextrin I: DE 4.0–7.0; maltodextrin II: DE 13.0–17.0; maltodextrin III: DE 16.5–19.5) were used for the design of three enantioselective, potentiometric membrane electrodes (EPMEs) for the assay of S-ketoprofen. The linear concentration ranges for the proposed electrodes were 10^?10 to 10^?8, 10^?9 to 10^?5, and 10^?10 to 10^?7 mol/L, with slopes of 58.0, 58.67, and 58.93 mV/decades of concentration and limits of detection of 1.49 × 10^?8, 2.43 × 10^?8, and 4.19 × 10^?11 mol/L for EPMEs based on maltodextrin I, II, and III, respectively. The EPMEs showed high reliability and effectiveness for the enantioanalysis of S-ketoprofen raw material and its pharmaceutical formulations.     

Newly selective electrochemical sensors for trace-level determination of Al(III) ions in drainage water,spiked tap water and pharmaceutical preparation samples

In this work, two newly sensitive and selective Al(III)-modified carbon paste electrodes (MCPEs) were developed based on diphenylcarbazone (DPC) modifier mixed with tricresyl phosphate plasticizer and either graphite powder (electrode I) or graphite powder mixed with graphene (electrode II). The potentiometric performance characteristics of the two electrodes were scrutinized and discussed. The proposed sensors showed a high electrochemical response in the linear concentration range of 1.0 × 10⁻⁶ to 1.0 × 10⁻² mol L⁻¹ with a good Nernstian slopes of 20.12 ± 0.30 mV decade⁻¹ and 20.63 ± 0.66 mV decade⁻¹ and limits of detection of 9.0 × 10⁻⁷ and 8.5 × 10⁻⁷ mol L⁻¹ for electrode (I) and electrode (II), respectively. Both electrodes showed a fast response time and reasonable thermal stability. The potentiometric response of the DPC-based electrodes was independent on the pH of the tested solutions in ranges of 2.5–5 and 2.5–5.5 for electrode (I) and electrode (II), respectively. The two electrodes can be also used in partially non-aqueous medium containing up to 20% (v/v) acetone or methanol with no significant changes in the working concentration ranges or the slopes. The proposed electrodes showed fairly good discriminating ability toward Al(III) ions in comparison with many other metal ions. The electrodes were applied successfully for Al(III) ions determination in drainage water, spiked tap water and pharmaceutical preparation samples. Furthermore, the electrode surfaces were characterized using energy-dispersive X-ray (EDX) and scanning electron microscopic (SEM) as surface characterization techniques and Fourier Transform Infrared (FT-IR) technique to confirm the interaction between Al(III) and DPC.

     

1‐Pyrrolidine Dicarbodithioate Based Electrodes for Determination of Iron(III) in Lubrication Oil

The lipophillic ammonium salt of 1‐pyrrolidine dicarbodithioic acid (PCDT) (I) was introduced as a new selective ionophore for an iron selective electrode. In addition, the effect of immobilization of 18‐crown‐6 (18CE6) (membrane type‐II), on the electrode performance was discussed. The slope of the PCDT‐based (I) electrode was (20 mV/decade). The linear concentration range was (10^?5–10^?1 M) after one day doping. The detection limit for electrode type‐(II) was (1.3×10^?6 M). For membrane with only 18CE6 (type‐III) the linear range and the detection limit were improved (10^?5–10^?1 M and 3.2×10^?6 M, respectively). The pH‐range was between 5–11 for type‐II, and III electrodes, while it was 7–11 for type‐I electrode. Most of the common cations were tested for the evaluation of the electrode selectivity with correlation to the ionic radii of the tested cations. Among them only Ag⁺ and Pb²⁺ were the real interference for type‐III electrode. Application of using the electrode for the determination of iron in lubrication oil samples was performed with RSD (1.77–2.7%) and (1.01–2.3%) for type‐II and III electrodes, respectively. The corresponding recovery ranges were (93.0–99.9%) and (96.3–100%). The obtained results were compared to those of an atomic absorption spectrophotometric method.     

Determination of L‐Vesamicol in Serum Samples Using Enantioselective,Potentiometric Membrane Electrodes Based on Antibiotics

Abstract

Enantioselective, potentiometric membrane electrodes (EPMEs) based on antibiotics are proposed for the enantioanalysis of L‐vesamicol. A carbon paste was modified with antibiotics (vancomycin, teicoplanin, and teicoplanin modified with acetonitrile), as chiral selectors. The EPMEs based on antibiotics were reliably used for enantiopurity tests of L‐vesamicol using the direct potentiometric technique. The following linear concentration ranges: 1.0×10^?6–1.0×10^?4, 1.0×10^?6–1×10^?3 and 1×10^?7?1×10^?2 mol/L; and detection limits: 1.1×10^?7, 9.6×10^?8, and 3.6×10^?8 mol/L were determine for vancomycin, teicoplanin, and teicoplanin modified with acetonitrile–based EPMEs, respectively. The proposed EPMEs were applied for the enantioanalysis of L‐vesamicol in urine samples.     

Iodide-Selective PVC Membrane Electrodes Based on Five Transitional Metal Chelates of bis-furfural-semi-o-tolidine

Abstract

Some new PVC membrane electrodes based on Co(II), Mn(II), Ni(II), Cu(II), and Zn(II)chelates of bis-furfural-semi-o-tolidine as carriers are described. The electrodes exhibited different selectivity behaviour compared with the electrode using a classical anion exchanger such as tetraalkyl ammonium. The results showed that the Cobalt(II) chelate-based electrodes had a Nernstian response to iodide ion ranging from 1.0 × 10^?1 to 1.0 × 10^?6 mol.L^?1 in a phosphate buffer solution of pH 2.0 with a detection limit of 6.4 × 10^?7 mol.L^?1 and a slope of 57.8 mV/dec at 25deg;C. The response mechanism was also investigated by use of both a.c. impedance and SPQC techniques. The Co(II) chelate-based electrodes were used to determine the iodide content of a drug with satisfactory results.     

Heterogeneous Membrane and Coated Wire Type Electrode with Chitosan as Ionophore in the Potentiometric Determination of Glutamate: Comparative Study

This study reports on two types of glutamate sensors based on chitosan, i) heterogeneous membrane and ii) coated wire (CWE). The linearity ranges are: i) membrane, 1.0×10^?5 to 1.0×10^?1 M and ii) CWE, 1.0×10^?5 to 1.0×10^?3 M. The LODs, and pH ranges are i) membrane, 5.0×10^?6 M and 4–8 and ii) CWE, 1.0×10^?5 M and 3–5, respectively. The presence of ionic species normally found in foodstuffs did not interfere in both electrodes. Interference in CWE was minimized by prior dilution of the sample. The CWE was further investigated for on‐line analysis. The material for proposed electrodes was cheaper and environmental friendly. Hence, they were suggested as alternative tools for the analysis of glutamate.     

Construction and Validation of New Electrochemical Carbon Nanotubes Sensors for Determination of Acebutolol Hydrochloride in Pharmaceuticals and Biological Fluids

A simple, rapid and a highly selective method for direct electrochemical determination of acebutolol hydrochloride (AC) was developed. The developed method was based on the construction of three types of sensors conventional polymer (I), carbon paste (II) and modified carbon nanotubes (MCNTs) carbon paste (III). The fabricated sensors depend mainly on the incorporation of acebutolol hydrochloride with phosphotungstic acid (PTA) forming ion exchange acebutolol‐phosphotungstate (AC‐PT). The performance characteristics of the proposed sensors were studied. The sensors exhibited Nernstian responses (55.6 ± 0.5, 57.14 ± 0.2 and 58.6 ± 0.4 mV mol L^?1) at 25 °C over drug concentration ranges (1.0 × 10^?6‐1.0 × 10^?2, 1.0 × 10^?7‐1.0 × 10^?2 and 5.0 × 10^?8‐1.0 × 10^?2 mol L^?1 with lower detection limits of (5.0 × 10^?7, 5.0 × 10^?8 and 2.5 × 10^?8 mol L^?1 for sensors (I), (II) and (III), respectively. The influence of common and possible interfering species, pharmaceutical additives and some related pharmacological action drugs was investigated using separate solution method and no interference was found. The stability indicating using forced degradation of acebutolol hydrochloride was studied. The standard addition method was used for determination of the investigated drug in its pharmaceutical dosage forms and biological fluids. The results were validated and statistically analysed and compared with those from previously reported methods.     

New Validated Potentiometric Determination of Vasodilator Pentoxifylline in its Pharmaceutical Formulations and Biological Fluids

The construction and performance characteristics of pentoxifylline selective electrodes were developed. Two types of electrodes: plastic membrane I and coated wire II were constructed based on the incorporation of pentoxifylline with phosphotungstic acid (PTA). The influence of membrane composition, kind of plasticizer, pH of the test solution, soaking time, and foreign ions on the electrodes was investigated. The electrodes showed a Nernstain response with a mean calibration graph slope of 56.77 ± 0.19 and 55.76 ± 0.71 mV decade^‐1 at 25 °C for electrode I and II respectively, over pentoxifylline concentration range from 1.0 × 10^‐5‐1.0 × 10^‐2 and 9.0 × 10^‐6‐1.0 × 10^‐2 mol L^‐1, with detection limits 4.89 × 10^‐6 and 3.90 × 10^‐6 mol L^‐1 for electrode I and II, respectively. The pH range of the constructed electrodes was 4‐6. Interferences from common cations, alkaloids, sugars, amino acids and drug excipients were reported. The results obtained by the proposed electrodes were also applied successfully to the determination of the drug in its pharmaceutical preparations and biological fluids.     

Chemical Modified Carbon Paste Electrode for Potentiometric Determination of Mo(VI) and its Application in Food Analysis and Agriculture Fertilizers

Since to the best of our knowledge, there is no potentiometric sensors based on carbon paste electrodes were proposed for the potentiometric determination of molybdenum(VI) ion. In this study, 2,2′-(propane-1,3-diylbis(oxy))dibenzoic acid (PBODBA) was synthesized and used as modifier in the fabrication of carbon paste electrode (CPE) for the quantification of molybdenum(VI). The developed electrodes I and II showed hexavalent Nernstian response of 9.80±0.05 and 9.90±0.08 mV decade⁻¹ over the concentration ranges of 1.0×10⁻⁷–1.0×10⁻³ and 1.0×10⁻⁸–1.0×10⁻³ mol L⁻¹, respectively. The electrodes showed good selectivity for Mo(VI). The modified electrodes were applied for the determination of Mo(VI) concentration in masscuaje agricultural fertilizer and spiked juice extractions containing several metals.     

Enantioanalysis of Butaclamol Using Enantioselective Potentiometric Electrodes

Abstract

Three enantioselective, potentiometric electrodes were proposed for the enantioanalysis of butaclamol. The electrodes were based on immobilization of maltodextrins (MDs) of different dextrose equivalences [4.0–7.0, I; 13–17, II; 16.5–19.5, III] into carbon paste. The electrodes based on MD I and II were used for the enantioanalysis of S-butaclamol within linear concentration ranges of 10^?10 to 10^?7 and 10^?10 to 10^?8, respectively, with slopes of 51.20 and 57.59 mV/decade of concentration; whereas the electrode based on MD III was used for the enantioanalysis of R-butaclamol within a linear concentration range between 10^?10 and 10^?7 with a slope of 58.50 mV/decade of concentration. Recoveries greater than 90% were recorded for the enantioanalysis of butaclamol in synthetic and urine samples.     

Design of a Vitamin B1‐Selective Electrode Based on an Ion‐Pair and Its Application to Pharmaceutical Analysis

Vitamin B₁‐selective electrodes with PVC membrane were developed that contain ion associates of vitamin B₁ with an inorganic anion, BiI₄^?, and an organic anion, brilliant yellow, as electrode‐active substances. The linearity ranges of the electrode function are 1.0×10^?5–1.0×10^?2 and 1.0×10^?4–1.0×10^?2 M, the electrode function slopes are 33.0±1.0 and 33.1±1.1 mV decade^?1, the detection limits are 5.5×10^?6 and 8.3×10^?5 M for BiI₄^? and brilliant yellow respectively. The working range of pH is 5–12. The efficiency of the use of electrodes for the vitamin B₁ content control in multivitamin pharmaceutical preparations was shown by direct potentiometry and potentiometric titration methods.     

Determination of Methimazole and Carbimazole Using Polarography and Voltammetry

Abstract

Anodic waves of methimazole (I) (1-methylimidazole-2-thiol) and carbimazole (II) (1-ethoxycarbonyl-3-methyl-2-thio-4-imidazoline) on mercury electrodes correspond to mercury salt formation. Both compounds form in the thiono form a soluble complex at pH < 6, compound (I) at higher pH-values a slightly soluble salt of the thiol form. Electrode processes involving the thiol form are complicated by adsorption. Oxidation at solid electrodes occurs only at potentials more than 0.5 V more positive. For compound (I) spectrophotometry indicated pK_a=12.0 ± 0.2. By d.c. polarography in 0.1 M H₂SO₄ containing 10% ethanol the determination of both compounds is possible between 4 × 10^? and 1 × 10^?3 M, by differential pulse polarography between 1 × 10^? and 1 × 10^?4 M, by differential pulse voltammetry at HMDE between 5 × l0^?7 and 6 × 10^? M.     

Highly Selective Chromium(III) PVC‐Membrane Electrodes Based on Some Recently Synthesized Schiff's Bases

Three recently synthesized Schiff's bases were studied to characterize their ability as Cr³⁺ ion carrier in PVC‐membrane electrodes. The polymeric membrane (PME) and coated glassy carbon (CGCE) electrodes based on 2‐hydroxybenzaldehyde‐O,O′‐(1,2‐dioxetane‐1,2‐diyl) oxime (L1) exhibited Nernstian responses for Cr³⁺ ion over wide concentration ranges (1.5×10^?6–8.0×10^?3 M for PME and 4.0×10^?7–3.0×10^?3 M for CGCE) and very low limits of detection (1.0×10^?6 M for PME and 2.0×10^?7 M for CGCE). The proposed potentiometric sensors manifest advantages of relatively fast response and, most importantly, good selectivities relative to a wide variety of other cations. The selectivity behavior of the proposed Cr³⁺ ion‐selective electrodes revealed a considerable improvement compared to the best previously PVC‐membrane electrodes for chromium(III) ion. The potentiometric responses of the electrodes are independent of pH of the test solution in the pH range 3.0–6.0. The electrodes were successfully applied to determine chromium(III) in water samples.     

Enantioselective,Potentiometric Membrane Electrodes for the Determination of L‐Pipecolic Acid in Serum

L ‐Pipecolic acid is a marker for peroxisomal disorders. Three enantioselective, potentiometric membrane electrodes were designed for the enantioanalysis of L ‐pipecolic acid. These electrodes are based on carbon paste impregnated with different maltodextrins (DE: 4.0–7.0 (I), 13.0–17.0 (II) and 16.5–19.5 (III), respectively) as chiral selectors and they can be used reliably for enantiopurity assay of L ‐pipecolic acid using a potentiometric method in the concentration ranges of 10^?8–10^?3, 10^?8–10^?5 and 10^?10–10^?6 mol/L for the maltodextrins I, II and III, respectively, based electrodes, with very low detection limits (magnitude orders of 10^?9 for I and II, respectively and 10^?12 mol/L for III). The proposed electrodes can be successfully applied for the enantioanalysis of L ‐pipecolic acid in serum samples.     

Simultaneous spectrofluorimetric determination of terbium,samarium and europium with hexafluoroacetylacetone-trioctylphosphine oxide and Triton X-100

In aqueous solution, the fluorescence intensity is a linear function of concentration in the ranges 1.0 × 10^?4-1.0 × 1.0^?6 M Sm and 1.0 × 10^?6-1.0 × 10^?8 M Tb and Eu. The optimum conditions are 1 × 10^?3 M hexafluoroacetylacetone, 1 × 10^?4 M trioctylphosphine oxide and 0.05% Triton X-100 at pH 3.0.