OH functionalized Multi-Walled Carbon Nanotube modified electrode as electrochemical sensor for the detection of Aceclofenac

ABSTRACT

The rapid electrochemical determination of Aceclofenac (ACF) has been employed by cyclic voltammetry (CV), differential pulse voltammetry (DPV) using developed OH-functionalised multiwalled carbon nanotube carbon paste electrode (OH-MWCNT/CPE). Modified electrode was characterised by scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDAX), X-ray diffraction spectroscopy (XRD), electrochemical impedance spectroscopy (EIS) and cyclic voltammetry (CV). The ACF exhibits two oxidation peaks at +0.4 V, +0.66 V and one reduction peak at +0.3 V. The active surface area of the bare carbon paste electrode (BCPE) and modified electrode have been characterised by using K₃[Fe(CN)₆] solution containing 0.1 M KCl. In DPV mode, variation of ACF gave the limit of detection (LOD = 3s/m) 0.246 μM over the concentration range 1.0 to 190.0 μM (R² = 0.9994). The developed electrode has good stability, reproducibility and could be successfully validated for the detection of ACF in pharmaceutical samples and biological fluids.     

Electrochemical determination of picric acid based on platinum nanoparticles–reduced graphene oxide composite

Platinum nanoparticles–reduced graphene oxide composite-modified glassy carbon electrode (PtNPs–rGO/GCE) was developed as a simple, selective and sensitive electrochemical sensor for determination of picric acid (PA). Cyclic voltammogram (CV) of PA showed three well-defined irreversible reduction peaks at the potentials of ?0.43, ?0.57 and ?0.66 V versus Ag/AgCl. In this work, the interference effect of other nitrophenol compounds (NPhCs) was significantly reduced by appropriate adjusting of pH. Square wave voltammetry was used for quantification of PA in the range of 5–500 µM (1.15–115 mg L^?1) with practical detection limit of 1 µM (0.23 mg L^?1). The proposed sensor was successfully applied for the determination of PA in two natural water samples.     

High-sensitive amperometric hydrazine sensor based on chemically synthesized zinc nitroprusside nanoparticle-supported carbon ceramic electrode

Zinc nitroprusside (ZnNP) nanoparticles were fabricated at the surface of zinc powder-doped carbon ceramic electrode (CCE) by a chemical derivatization process. This modified electrode was characterized by scanning electron microscopy, atomic force microscopy and cyclic voltammetry techniques. The charge transfer rate constant (k _s) and charge transfer coefficient (α) were calculated for the electron exchange reaction of the ZnNP thin film. The ZnNP nanoparticle-modified CCE (ZnNP|CCE) showed good electrocatalytic activity toward hydrazine oxidation. The limit of detection (S/N = 3) and sensitivity were found to be 0.16 µM and 0.21 µA/µM, respectively. The mechanism of hydrazine electrooxidation at the electrode surface was studied. Finally, the ZnNP|CCE was successfully used for the determination of trace amount of hydrazine in different spiked and real samples.     

Anodic Stripping Voltammetry: Arsenic Determination in Ancient Bone Samples

Abstract

A highly sensitive method for the determination of arsenic (As) content in ancient bone samples was studied using a gold tipped rotating disc electrode and differential pulse anodic stripping voltammetry. Factors affecting sensitivity and precision, including electrolyte concentration, deposition potential, deposition time, and rotation rate were investigated. Electroinactive As(V) was reduced to As(III) by HCl 30% w/v prior to electroanalytical measurements. For a deposition time of 120 sec, the lowest detection limit (LOD) for arsenic was 1.078 µg/L. Optimized working conditions are defined as a deposition potential of ?1200 mV with a deposition time of 120 sec, 10 M HCl as the supporting electrolyte, and a rotation rate of 2000 rpm. Results of electroanalytial measurements in ancient bone samples are compared with those obtained from the hydride generation atomic absorption spectroscopy (HG‐FAAS) analysis. Analytical relevancy of the two methods was then compared with the aid of statistical data treatment.     

Enhanced Specificity and Sensitivity for the Determination of Nickel(II) by Square-wave Adsorptive Cathodic Stripping Voltammetry at Disposable Graphene-modified Pencil Graphite Electrodes

Chemical sensors relying on graphene-based materials have been widely used for electrochemical determination of metal ions and have demonstrated excellent signal amplification. This study reports an electrochemically reduced graphene oxide (ERGO)/mercury film (HgF) nanocomposite-modified pencil graphite electrode (PGE) prepared through successive electrochemical reduction of graphene oxide (GO) sheets and an in situ plated HgF. The ERGO-PG-HgFE, in combination with dimethylglyoxime (DMG) and square-wave adsorptive cathodic stripping voltammetry (SW-AdCSV), was evaluated for the determination of Ni²⁺ in tap and natural river water samples. A single-step electrode pre-concentration approach was employed for the in situ Hg-film electroplating, metal-chelate complex formation, and non-electrolytic adsorption at –0.7 V. The current response due to nickel-dimethylglyoxime [Ni(II)-DMG₂] complex reduction was studied as a function of experimental paratmeters including the accumulation potential, accumulation time, rotation speed, frequency and amplitude, and carefully optimized for the determination of Ni²⁺ at low concentration levels (μg?L^?1) in pH 9.4 of 0.1 M NH₃–NH₄Cl buffer. The reduction peak currents were linear with the Ni²⁺ concentration between 2 and 16?μg?L^?1. The limits of detection and quantitation were 0.120?±?0.002?µg?L^?1 and 0.401?±?0.007?µg?L^?1 respectively, for the determination of Ni²⁺ at an accumulation time of 120?s. The ERGO-PG-HgFE further demonstrated a highly selective stripping response toward Ni²⁺ determination compared to Co²⁺. The electrode was found to be sufficiently sensitive to determine metal ions in water samples at 0.1?µg?L^?1, well below the World Health Organization standards.     

A Nitrite Electrochemical Sensor Based on Boron‐Doped Diamond Planar Electrochemical Microcells Modified with a Monolacunary Silicotungstate Polyoxoanion

A new boron doped diamond microcells (BDD) was modified, for rapid, selective and highly sensitive determination of nitrite, using a coating film of polyoxometalates (POMs), formed by cyclic voltammetry on the molecular p‐phenylenediamine (PPD) functionalized BDD. The scanning electron microscopy (SEM) technique was used to examine the morphology of (PPD/SiW₁₁) modified (BDD) electrode. It was found that (SiW₁₁) layer was uniformly formed on the electrode surface. It was observed that (BDD/PPD/SiW₁₁) showed excellent electrocatalytic activities towards nitrite ion. Under the selected conditions, the anodic peak maximum at ?0.6 V was linear versus nitrite concentration in the 40 µM–4 mM range, and the detection limit obtained was 20 µM. The newly developed electrode has been successfully applied to the determination of nitrite content in real river water samples.     

Assessment of Lead and Cadmium in Canned Foods by Square-Wave Anodic Stripping Voltammetry

Abstract

This work reports the simultaneous determination of lead and cadmium in canned foods samples using square-wave anodic striping voltammetry (SWASV) on a bismuth film electrode (BiFE). The metal ions and bismuth were simultaneously deposited by reduction at ?1 V on a rotating carbon-paste disk electrode. Then, the preconcentrated metals were oxidized by scanning the potential of the electrode from ?1 to ?0.4 V using a square-wave waveform. The electrode displayed excellent linear behavior in the examined concentration range, from 5 to 150 µg/L of cadmium and lead (r² = 0.999 for both). Using the optimized conditions, the limits of detection were 0.27 µg/L for cadmium and 0.35 µg/L for lead. The reproducibility of the proposed sensor, evaluated in terms of relative standard deviation (RSD), were 5.8% and 3.7% of Cd and Pb, respectively for five measurements. Finally, the system based on BiFEs combined with rotating disk electrode was applied to determination of lead and cadmium in canned food samples. The results obtained were validated by inductively coupled plasma optical emission spectroscopy (ICP-OES).     

High-performance electrochemical sensor based on electrodeposited iron oxide nanoparticle: catecholamine as analytical probe

In this paper, we report the synthesis and electrocatalytic activity of electrodeposited Fe₂O₃ nanoparticles modified on a glassy carbon electrode as highly sensitive sensors for determination of catecholamines. Results showed that the Fe₂O₃ nanoparticles on a glassy carbon electrode exhibit excellent catalytic activity toward catecholamines oxidation, including levodopa, dopamine, and epinephrine, resulting in a marked lowering in the peak potential and considerable improvement of the peak current as compared to the electrochemical activity at the bare glassy carbon electrode. The electrochemical characterizations of catecholamines were performed using cyclic voltammetry, chronoamperometry, and differential pulse voltammetry techniques. The electrocatalytic currents increase linearly with the levodopa, dopamine, and epinephrine concentrations in the ranges of 0.0625–1000, 0.25–1500, and 0.125–1000 µM, respectively, and the detection limits (3σ) were 24 ± 2, 14 ± 2, and 12 ± 2 nM, respectively.     

Determination of Sterically Hindered Phenols and α-Tocopherol by Cyclic Voltammetry

Sterically hindered phenols (2,6-di-tert-butyl-4-methylphenol (BHT) and its derivatives) are irreversibly oxidized at +0.96–1.30 V on glassy carbon electrode (GCE) in 0.1 M LiCIO₄ in acetonitrile in accordance to cyclic voltammetry data. α-Tocopherol gives oxidation step at +0.4 V on voltammograms under the same conditions. Oxidation process leads to formation of corresponding quinoid derivatives. Calibration graphs linearity is 1.5–2 order for all compounds under investigation. Limits of detection are in the range 9.6–44.3 µM. The approach has been applied for determination of BHT and α-tocopherol in vegetable and lubricating oils as well as pharmaceuticals and cosmetics using preliminary single extraction of analytes with acetonitrile for 15 min at oil/extractant ratio of 1:2.5.     

Lead-doped carbon ceramic electrode as a renewable surface composite electrode for the preparation of lead dioxide film and detection of <Emphasis Type="SmallCaps">l</Emphasis>-tyrosine

Lead-doped carbon ceramic electrode as a new type of renewable composite electrode was prepared by mixing the lead powder with electrode matrix before gelation. Pb on the electrode surface was then converted to lead dioxide by the potential scanning of the composite electrode in 0.1 M NaOH solution in the range of ? 0.3 to 0.7 V versus SCE. The composition and morphology of the electrodes were studied by energy dispersive X-ray spectrometry, scanning electron microscopy, and atomic force microscopy techniques. Cyclic voltammetry and chronoamperometry techniques were also used to study the electrocatalytic activity of the modified electrode toward the oxidation of the l-tyrosine. The best results were obtained at a working potential of 0.45 V (vs. SCE) in 0.1 M NaOH solution. The sensor exhibited a good linear response in the range of 5–1458 µM with a coefficient of determination of 0.9963. The detection limit was 0.77 µM, and sensitivity was 37.4 μA mM^?1. In addition, the modified electrode showed high stability and interference-free response for to detection of the l-tyrosine.     

Electrochemical Detection of Pb(II) by Glassy Carbon Electrode Modified with Amine-Functionalized Magnetite Nanoparticles

An amine-Fe₃O₄ modified glassy carbon (GC) electrode was constructed for detecting Pb(II) ions in wastewater. The electrode was characterized by cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS). Square wave anodic stripping voltammetry (SWASV) was used to detect the Pb(II), and the detection limit of Pb(II) was 0.15 µM. The sensitivity of the electrode to detect Pb(II) was about 10.07 µA/µM, with a correlation coefficient of 0.991, which was approximately 10 times bigger than that of a pure Fe₃O₄ modified electrode. The electrode also showed good selectivity and stability. This results indicated that the amine-magnetite material could have some potential applications in heavy metal ions detection in wastewater.     

Sensitive voltammetric determination of rutin at a carbon nanotubes-ionic liquid composite electrode

A new composite electrode of multiwall carbon nanotubes (MWNTs) and 1-dodecyl-3-methylimidazolium hexafluorophosphate (DDMIMPF₆) was fabricated to determine rutin. This electrode showed very attractive electrochemical performances compared to other kinds of ionic liquid modified electrodes and notably improved sensitivity and stability. Electrochemical behavior of rutin at the composite electrode had been investigated in pH 2.09 Britton–Robinson buffer solution by cyclic voltammetry and square wave voltammetry. The experimental results suggested that the composite electrode exhibited an electrocatalytic activity toward the redox of rutin. The electrochemical parameters of rutin were calculated with the results of the charge transfer coefficient (α) and the standard rate constant (k _s) as 0.48 and 2.09 s^?1. Under the selected conditions, the reduction peak current was linearly dependent on the concentration of rutin in the range of 0.03–1.5 μM, with a detection limit of 0.01 μM (S/N?=?3). The relative standard deviation for six times successive determination of 1 μM rutin was 1.6 %. The method was successfully applied to the determination of rutin in tablets and urine samples without the influence of the coexisting substances. In addition, the MWNTs/DDMIMPF₆ composite electrode exhibits a distinct advantage of simple preparation, surface renewal, good reproducibility, and stability.     

Electrodeposition and stripping voltammetry of arsenic(III) and arsenic(V) on a carbon black–polyethylene composite electrode in the presence of iron ions

In this work, a new sensor is proposed for the stripping voltammetric determination (anodic stripping voltammetry—ASV) of total arsenic(V) or arsenic(III). The sensor is based on an Fe-modified carbon composite electrode containing 30 % carbon black–high-pressure polyethylene (CB/PE). The modification with iron is achieved by the addition of Fe(III) or Fe(II) ions to the sample solution and co-electrodeposition of iron and arsenic on the CB/PE electrode. In anodic stripping voltammetry, two peaks are observed: an Fe peak at ?0.45 or ?0.29 V and a peak at 0.12?±?0.07 V which depends on the arsenic concentration and corresponds to the As(0) → As(III) oxidation, as is the case with other solid electrodes. The optimum conditions proposed for ASV determination of As(V) and As(III) in solutions in the presence of dissolved oxygen are the following: the background electrolyte is 0.005 M HCl containing 0.5–1 mg/?L Fe(III) for As(V) and containing 1.0–1.5 mg/?L Fe(III) for As(III), respectively; E _dep?=??2.3 V; rest period at ?0.10 V for 3–5 s before the potential sweep from ?0.2 to +0.4 V; scan rate is 120 mV/?s. The detection limit (LOD, t?=?120 s) for As(III) and As(V) is 0.16 and 0.8 μg/?L, respectively. Various hypotheses on the effect of Fe ions and atoms on the electrodeposition and dissolution of arsenic are considered. The new method of determination of As(III) and As(V) differs from known analogues by its simplicity, low cost, and easy accessibility of the electrode material. It allows the voltammetric determination of total arsenic after chemical reduction of all its forms to As(III) or after their oxidation to As(V).     

Voltammetric determination of herbicide molinate in river water and rice samples using solid silver amalgam electrode fabricated with nanoparticles

The evaluation of the voltammetric behaviour and the determination of herbicide molinate were performed for the first time over the surface of solid amalgam electrode fabricated with silver nanoparticles using cyclic voltammetry and square-wave voltammetry techniques. The experimental and instrumental parameters were evaluated to reach the maximum analytical response for molinate. It was achieved when a medium composed of 0.04 mol L^?1 Britton–Robinson buffer at the pH value of 4.0 was used. Under these conditions, molinate showed one pronounced reduction peak at E_p = ?0.37 V (vs. Ag/AgCl 3 mol L^?1) that was characterised as an irreversible system. An analytical curve was constructed at the concentration range from 9.36 to 243.49 µg L^?1 and a limit of detection of 2.34 µg L^?1 was obtained. The amalgam electrode presented good stability during the measurements with relative standard deviation (RSD) values of 2.9% for the repeatability and 5.4% for the reproducibility. The voltammetric method developed here could be conveniently applied for the determination of molinate in river water and rice spiked samples at levels below those established on the legislations of European Union and Brazil with good accuracy (RSD of less than 5% for all samples). Comparison with HPLC technique was carried out and the results indicated satisfactory concordance. According to the results depicted here, the silver nanoparticles solid amalgam electrode showed itself highly sensitive and an interesting alternative for the routine analysis of molinate in water and food samples. Furthermore, it introduces an environmentally acceptable alternative to the mercury electrodes, most commonly used for determination of reducible pesticides.     

Hydrogen Peroxide Biosensor Based on the Electrochemistry of the Myoglobin‐TATP Composite Film

Abstract

Direct electrochemistry of the myoglobin‐triacetone triperoxide (Mb‐TATP) composite on carbon paste (CP) electrode is reported. This electrode gives a well‐defined and quasi‐reversible cyclic voltammogram for the Mb Fe^III/Fe^II redox coupled with the formal potential (E?′) of ?0.302 V (vs. Ag/AgCl) in pH 6.92 phosphate buffer. Electronic and vibrational spectroscopies show that the Mb in the composite retains a structure similar to its native form. The enzymatic reactivity to the reduction of H₂O₂ has been studied for the Mb‐TATP film. The analytical performances have been obtained with the linear range of 78.32–1135.64 µM, the detection limit of 55 µM (S/N=3), and the apparent Michaelis‐Menten constant (K _m) of 662.8 µM. This H₂O₂ biosensor based on the electrocatalysis of the immobilized Mb presents a higher stability within two weeks.     

Anodic Oxidation of α‐Lipoic Acid at a Glassy Carbon Electrode and Its Determination in Dietary Supplements

Abstract

Direct electrochemistry of alpha‐lipoic acid (ALA) was performed at a glassy carbon electrode using cyclic, differential pulse and square wave voltammetry over a wide range of pH. The oxidation of ALA is an irreversible process, pH independent, and involves the charge transfer of one electron. The diffusion coefficient of ALA was calculated from the results obtained at pH 6.9 in 0.1 M phosphate buffer and was shown to be D ₀=1.1×10^?5 cm² s^?1. The limits of detection (LOD) and quantification (LOQ) calculated from the results obtained at this pH are 1.8 and 6.1 µM, respectively.

The lipoic acid content in two dietary supplements samples, a syrup containing ALA and capsules of ALA, has been determined directly at the glassy carbon electrode by differential pulse voltammetry using the standard addition method.     

Electrochemical Determination of Norepinephrine on Cathodically Pretreated Poly(1,5‐diaminonaphthalene) Modified Electrode

A sensitive and simple electrochemical method for norepinephrine (NE) determination was developed based on a poly(1,5‐diaminonaphthalene) film electrode (PDAN). Cathodically pretreated PDAN presents good selectivity, sensitivity, and reproducibility for NE. The polymer film can be easily electropolymerized onto a platinum electrode by cyclic voltammetry in 1.0 M HClO₄. A cathodic pretreatment, consisting of the application of a potential of ?0.7 V for 3 s (vs. Ag/AgCl) to PDAN before each voltammetric measurement, enhanced the electrochemical activity of NE with no inference of ascorbic acid (AA). In optimized conditions, PDAN presents linear responses for NE in the range of 9.90 to 90.9 µM by differential pulse voltammetry (DPV) with a detection limit of 1.82 µM. A relative standard deviation of 3.0 % was obtained for 10 consecutive measurements of 40.0 µM NE solutions. The cathodically pretreated PDAN was successfully applied for NE determination in pharmaceutical formulation samples.     

The Electro‐Oxidation of Formaldehyde at a Boron‐Doped Diamond Electrode

Abstract

The characteristics of the boron‐doped diamond (BDD) electrode in this work were studied by atomic force microscope (AFM), scanning electron microscopy, and Raman spectroscopy. The electro‐oxidation of formaldehyde at the BDD electrode in 0.5 M K₂SO₄ with different pH was studied by cyclic voltammetry and amperometry. There is no significant oxidation peak of formaldehyde in acidic solution because the oxidation of formaldehyde is at the potential range of water discharge. However, in neutral solution, there is a well‐defined oxidation peak at about +2.2 V vs. Ag/AgCl. The relation between the response current and formaldehyde concentration is linear behavior at the concentration range from 50 to 600 µM. Besides, in neutral solution, the oxidation of formaldehyde is dominated by indirect oxidation at lower formaldehyde concentration, and it is dominated by direct oxidation at higher concentration. Finally, in alkaline solution, the oxidation of formaldehyde is dominated by indirect oxidation caused by a powerful oxidant and is related to the ratio of the amounts of formaldehyde and OH molecules at the BDD electrode surface.     

Electrochemical Oxidation of Phenothiazine Derivatives at Glassy Carbon Electrodes and Their Differential Pulse and Square‐wave Voltammetric Determination in Pharmaceuticals

Abstract

Three 2,10‐disubstituted phenothiazines—chlorpromazine hydrochloride (CPM), thioridazine hydrochloride (TR) and propericiazine (PRC)—were electrochemically studied in various buffer systems at different pH values, using a glassy carbon electrode. The substances were electrochemically oxidized at potential range 0.55–0.75 V. The oxidation was reversible and exhibited diffusion‐controlled process. The mechanism of the oxidation process is discussed. According to the linear relation between peak current and concentration, differential pulse voltammetry (DPV) and square wave voltammetry (SWV) methods for quantitative determination of chlorpromazine and propericiazine in 0.1 M HClO₄, and thioridazine in pH 2 phosphate buffer, was applied. Both the repeatability and reproducibility of the methods were also determined for all studied substances. The developed procedures were successfully applied to the determination of chlorpromazine and thioridazine in pharmaceutical dosage forms.     

Simultaneous Determination of Isoproterenol,Acetaminophen and Folic Acid Using a Novel Nanostructure‐Based Electrochemical Sensor

In this study, a carbon paste electrode modified with (E)‐2‐((2‐chlorophenylimino)methyl)benzene‐1,4‐diol (CD) and titanium dioxide nanoparticles (TiO₂) was used to prepare a novel electrochemical sensor. The objective of this novel electrode modification was to seek new electrochemical performances for the detection of isoproterenol (IP) in the presence of acetaminophen (AC) and folic acid (FA). Initially, cyclic voltammetry (CV) was used to investigate the redox properties of this modified electrode at various scan rates. In the following, the mediated oxidation of IP at the modified electrode was described. The results showed an efficient catalytic activity of the electrode for the electrooxidation of IP, which leads to a reduction in its overpotential by more than 235 mV. The value of the electron transfer coefficient (α), catalytic rate constant (k_h) and diffusion coefficient (D) were calculated for IP, using electrochemical approaches. Based on differential pulse voltammetry (DPV), the oxidation of IP exhibited a dynamic range between 0.5 and 1000 µM and a detection limit (3σ) of 0.47 µM. DPV was used for simultaneous determination of IP, AC and FA at the modified electrode. Finally, this method was used for the determination of IP in real samples, using standard addition method.