Flow-Injection Chemiluminescence Determination of Fluoroquinolones

ABSTRACT

A new flow-injection CL method was developed for the determination of fluoroquinolones including ofloxacin, norfloxacin, ciprofloxacin and lomefloxacin in pharmaceutical preparations, based on the chemiluminescence reaction of sulphite with cerium(IV) sensitized by these compounds. The linear ranges are 0.04 to 4.0 μg ml^?1 for ofloxacin and 0.4 to 40.0 μg ml^?1 for norfloxacin, ciprofloxacin and lomefloxacin, respectively. The detection limits are 0.016 μg ml^?1 for ofloxacin and 0.16 μg ml ^?1 for norfloxacin, ciprofloxacin and lomefloxacin, respectively. The relative standard deviations (RSD) are 2.1 to 2.6% (n=10) for these fluoroquinolones. The analytical procedure has been applied to the determination of the fluoroquinolones in pharmaceutical commercial formulations. The results are in agreement with those obtained by the official methods.     

A Fluorosensor with Immobilized Cyclodextrin As A Substrate

Abstract

A flow-through optosensor for phenylalanine and tyrosine is described in this paper. The sensor is developed in conjunction with a flow-injection analysis system and uses immobilized β-cyclodextrin as the sensing agent. The analytical performance characteristics of the proposed sensor for analysis of very low levels of phenylalanine and tyrosine were as follows: the detection limits for phenylalanine and tyrosine were 0.20 μg ml^?1 and 8.9 ng ml^?1, respectively. The observed relative standard deviations were 1.03% for 50 μg ml^?1 of phenylalanine (n = 7) and 3.6% for 0.1 μg ml^?1 of tyrosine (n = 7), respectively.     

Study on Chemiluminescence Assay of Surfactant PEG-400 Using Luminol–Hydrogen Peroxide System

Abstract

Based on the fact that nonionic surfactant polyethylene glycol-400 (PEG-400) catalyzed the chemiluminescence of luminol-H₂O₂ system, a novel and simple chemiluminescence method has been developed for the determination of PEG-400. Under the optimal conditions, the standard curve was Y = 198835X–2091.8, where the correlation coefficient (R) was 0.9999. The detection limit was 4 × 10^?5 g·ml^?1 PEG-400 and the linear range was 1.0 × 10^?4–4.0 × 10^?2g·ml^?1. The relative standard deviation was 3.2% at 2.0 × 10^?3 g·ml^?1 PEG-400 (n = 7). This method has been applied to the determination of PEG-400 in cosmetic samples with satisfactory results. Furthermore, the dynamics characteristic curve of PEG-400 in luminol-H₂O₂ system was compared to typical metallic ion and other surfactants. Moreover, the mechanism of the luminol-H₂O₂-PEG-400 chemiluminescence system was studied, assisted by fluorescence spectra and UV spectra.     

A chemiluminescence flow injection system for nitrite ion determination

A chemiluminescence system is described for the determination of nitrite ion based on new designs for an ozone generator, liquid-gas separator and chemiluminescence reaction cell. The method is based on the gas-phase chemiluminescence reaction between ozone and nitric oxide, which is generated from the reduction of nitrite with iodide in sulfuric acid solution. The efficiency of the system was evaluated by investigation of the analytical performance characteristics of the system for nitrite determination in batch and flow injection procedures. Under optimal conditions, the chemiluminescence response of the system was linear against the nitrite concentration over the range 1 to 1 × 10⁴ ng ml^?1 in the batch procedure and 10 to 5 × 10³ ng ml^?1 in the flow injection procedure, with detection limits of 1 and 10 ng ml^?1, respectively. The method is highly selective and allows for the determination of nitrite in the presence of high concentrations of several cationic, anionic and nitrogen containing species. It has been successfully applied to the analysis of nitrite in natural water and soil extracts.     

Chemiluminescence Determination of Organophosphorus Pesticides Chlorpyrifos in Vegetable

Abstract

A novel chemiluminescence method for the quantitative assay of the organophosphorus pesticide chlorpyrifos in vegetable samples is presented. The determination is based on the reaction of chlorpyrifos with luminol-H₂O₂ in alkaline medium with sodium chloride being enhancer. Under the optimum conditions, the increased CL intensity was proportional with the concentration of chlorpyrifos in the range of 1.0 × 10^?8 g · ml^?1 ? 1.0 × 10^?6 g · ml^?1 and the detection limit was 3.5 × 10^?9 g · ml^?1 (3σ). The relative standard is less than 3.9% for 5.0 × 10^?7g · ml^?1 chlorpyrifos (n = 7). This method has been successfully applied to the determination of chlorpyrifos residue in vegetable sample. Further study was focused on the mechanism of chlorpyrifos and the possible mechanism was proposed.     

Simultaneous Determination of Valsartan and Hydrochlorothiazide in Tablets by High-Performance Liquid Chromatography

ABSTRACT

A method for the simultaneous determination of valsartan and hydrochlorothiazide in tablets is described. The procedure, based on the use of reversed-phase high-performance liquid chromatography, is linear in the concentration range 5.0-10.0 μg ml^?1 for valsartan and 0.5-2.0 μg ml^?1 for hydrochlorothiazide, is simple and rapid and allows accurate and precise results. The limit of detection was 1.0 μg ml^?1 for valsartan and 0.05 μg ml^?1 for hydrochlorothiazide.     

Interactions of Nile Blue Sulphate with Nucleic Acids as Studied by Resonance Light-Scattering Measurements and Determination of Nucleic Acids at Nanogram Levels

ABSTRACT

The interactions of nile blue sulphate (NBS) with nucleic acids, including calf thymus DNA, fish sperm DNA and yeast RNA, were characterized with resonance light-scattering (RLS) measurements by using a common spectrofluorometer. Accordingly a method for the determination of nucleic acids at nanogram levels was established. At pH's of 7.20～7.60 and ionic strengths lower than 0.012, the interactions of NBS with nucleic acids result in three characteristic RLS peaks at 293.4 nm, 349.4 nm and 560.4 nm. Mechanism study shows that these peaks are ascribed to the long range assembly of NBS on the molecular surface of nucleic acids, which depends on pH, ionic strength and the stranded structure of nucleic acids. A Scatchard plot was constructed by using the RLS data, yielding the assembly number and assembly constant being 6.4 and 7.13x10⁶ mol^?1 1 for NBS assembly on the molecular surface of calf thymus DNA. The same parameters are 6.6 and 4.58x10⁶ mol^?1 1 for the assembly on that of fish sperm DNA, 3.9 and 1.67x10⁶ mol^?1 1 on that of yeast RNA, respectively. Linear relationships were found between the enhanced RLS intensity at 293.4 nm and nucleic acid concentration. If 1.2x10^?5 mol I^?1 NBS was employed, 0～0.80 μg ml^?1 calf thymus DNA and fish sperm DNA, 0.20～0.60 μg ml^?1 yeast RNA can be determined with the determination limits being 3.2 ng ml^?1 for calf thymus DNA, 11.5 ng ml^?1 for fish sperm DNA and 38.3 ng ml^?1 for yeast RNA, respectively. Four synthetic samples were determined with satisfaction.     

Low-Temperature Phosphorescence Analysis of Mebendazole and Related Imidazoles

Abstract

Native low-temperature phosphorescence of mebendazole and flubendazole in ethanol is used for the determination of these imidazoles in anthelmintic preparations with wavelength maxima and detection limits of λ_EXC = 322 nm, λ_EM = 454 nm; 10 ng ml^?1 and λ_EXC = 325 nm, = λ_EM = 455 nm; 5 ng ml^?1, respectively, with linear response up to 8 μg ml^?1 and 9 μg ml^?1, respectively. The structural basis of these phenomena is discussed for both compounds and for related imidazoles and benzimidazoles. Apart from good sensitivity and excellent specificity offered by the technique, the use of cryogenic equipment (liquid nitrogen, special cuvettes, expensive dewar cells) implies some disadvantages for routine analyses.     

Application de la Polarographie Sinusoidale au Dosage Sanguin de L'indomethacine

Abstract

Alternative current polarography has been applied to indomethacin determination in serum, after dichloromethan extraction at pH 3.0. Solvent is evaporated and the residue submited to hydrolysis by NaOH. The indole derivative obtained is nitrosated by nitrous acid at pH 3,5. The indole-nitrosamine formed is measured by polarography at pH 1,3 and compared with an added quantity of the pure nitrosated product. The proposed method is selective and sensitive; it allows measurement of concentrations in serum as low as o,30 μg ml^?1 (0.83. 10^?9 moles ml^?1).     

Use of A Novel Acetone-H2O2−C10− Chemiluminescence System for the Determination of Iodide Ion

Abstract

The present paper reports a new chemiluminescence system, i.e, acetone-H₂O₂?C10^?, which can be catalyzed by iodide ion (I^?). Based on this catalysis, a new chemiluminescence method for the determination of trace iodide ion is proposed. the optimum conditions are reported in this note. the detection limit is 2 × 10^?11 g/ml I^?, the linear dynamic range is 4 × 10^?10 g/ml to 3 × 10^?7 g/ml I^?, and the variation coefficient at an iodide concentration of 5 × 10^?9 g/ml I^? (n=10) is 4.6%. the method has been satisfactorily applied to the determination of trace iodide ion in water.     

Spectrophotometric Analysis of some Phenothiazine Neuroleptics using Chloramine-T

ABSTRACT

A sensitive and selective spectrophotometric method has been developed for the determination of six phenothiazine neuroleptics. The method is based on the interaction of the drugs with chloramine-T in sulphuric acid medium to yield a red, reddish-violet, orange or greenish-blue intermediate with maximum absorption at 500-636 nm. Beer's law is obeyed over the range 5-125 μg ml^?1 of the drugs. The apparent molar absorptivities were found to be in the range 1.04x10³ to 5.46x10³ 1.mol^?1cm^?1. The investigated drugs were assayed in tablets and injections. The mean percentage recoveries were 97.65-101.75 and the relative standard deviations were found to be less than 2%.     

Colorimetric Determination of Propofol in Bulk form,Dosage Form and Biological Fluids

ABSTRACT

Propofol is coupled with 2, 6-dichloroquinone-4-chlorimide (DCQ) in a reaction buffered at pH 9.6 to give a colored product having an analytically useful maximum at 635 nm. The factors affecting the color generation were optimized and incorporated in the procedure. The reacted propofol has a molar absorptivity of 3.9 × 10^?4 L mol^?1 cm^?1, and Beer's law is obeyed for concentrations 1-5 μg ml^?1 with detection limit 0.25 μg ml^?1. The method was found applicable to biological fluids (plasma and urine) spiked with propofol at concentration levels 1-5 μg ml^?1 for plasma and 1-5 μg 0.5 ml^?1 urine (less sensitivity is obtained with urine volumes above 0.5 ml) with detection limits 0.28 μg ml^?1 for plasma and 0.4 μg 0.5 ml^?1 urine. The average recovery for the commercial preparation (1% w/v propofol emulsion intravenous injection for infusion) was 99.54% with an RSD of 1.05%. The method was validated by an adopted HPLC method. The results obtained by the HPLC method for the commercial preparation were statistically compared with the proposed method and evaluated at the 95% confidence limits.     

Sensitive Chemiluminescence Determination of Three Thiol Compounds Based on Cu(II)-Catalyzing Luminol Reaction in the Absence of an Oxidant

Abstract

A simple and sensitive flow-injection chemiluminescence method was proposed for the determination of three thiol compounds, namely cysteine, acetylcysteine, and glutathione. Weak chemiluminescence was produced directly by the reaction of these mentioned compounds with luminol in an alkaline solution without adding any special oxidants. The chemiluminescence signal could be significantly enhanced by Cu(II). The proposed method allows the determination of 4.0 × 10^?9 to 1.0 × 10^?7 g/mL cysteine, 7.0 × 10^?10 to 1.0 × 10^?7 g/mL acetylcysteine, and 4.0 × 10^?9 to 1.0 × 10^?6 g/mL glutathione with the detection limits of 8 × 10^?10 g/mL, 2 × 10^?11 g/mL, and 7 × 10^?10 g/mL, respectively. The proposed method was applied to the analysis of some commercial formulations containing acetylcysteine.     

Integrated Retention/Spectrophotometric Detection Method for the Determination of Formaldehyde

Abstract

An integrated-sensor method for the determination of formaldehyde based on retention of the reaction product of the analyte with p-rosaniline and sulfite in a flow-cell packed with Dowex 1-X-8 anion exchange resin was developed. The method has a good selectivity with a detection limit of 0.3 μg ml^?1 (1 ml sample) or 75 ng ml^?1 (2 ml sample), and a linear range between 1–30 μg ml^?1. The relative standard deviations (n = 11) were 2.8 and 1.3% for 2 and 20 μg ml^?1 formaldehyde, respectively. Depending on the working conditions, the sampling frenquency ranged between 10 and 18 h^?1. The method was applied to the determination of formaldehyde in well water.     

Determination of Steroids in Human Urine by Micellar Liquid Chromatography

Abstract

A simple and sensitive method for the determination of steroids using micellar liquid chromatography is described. The steroids, including hydroxycorticosterone. corticosterone, northisterone, testosterone, mexdroprogesterone acetate and progesterone, were separated by reversed-phase using a micelles mobile phase following UV detection at 245 nm. The parameters affecting retention of the test solutes such as the concentration of sodium dodecyl sulfate (SDS) and n-butanol-1 in the mobile phase were investigated. It was found that the retention of the solutes was dependent on the composition of mobile phase. The linear calibration plots range from 0.1 to 10 μg ml^?1 in mobile phase containing 5.0 × 10^?2 mol l^?1 SDS/9 % n-butanol-1 at pH 6.0, and the detection limit in order of 0.1 μg ml^?1 was obtained. The proposed method was used for the determination of steroids in urine using direct injection of samples without previous treatment.     

Determination of Puerarin in Pharmaceutical Injection by Flow Injection Analysis with Acidic Potassium Permanganate–Glyoxal Chemiluminescence Detection

Abstract

A simple flow injection chemiluminescence method with synergistic enhancement has been investigated for the rapid and sensitive determination of puerarin. The method is based on the enhancing effect of puerarin on the chemiluminescence emission generated by the oxidation of glyoxal with potassium permanganate in a sulfuric acid medium. The optimization of chemical variables influencing the chemiluminescence response of the method has been carried out by applying experimental design, using the proposed flow?injection manifold. Under the optimal conditions, the enhanced chemiluminescence intensity was linear with the concentration of puerarin over the range from 10.0 ng · ml^?1 to 7.0 µg · ml^?1 (R²=0.9972) with a detection limit (3σ) of 3.0 ng · ml^?1. At a flow rate of 3.0 ml · min^?1, a complete analytical process could be performed within 0.5 min, including sampling and washing, with a relative standard deviation of less than 3.0%. The proposed method was applied successfully in the assay of puerarin in pharmaceutical injection and human urine. The mechanism of chemiluminescence reaction was discussed briefly.     

Flow Injection Chemiluminescence Determination Of Tetracyclines

Abstract

A fast and simple flow injection chemiluminescence method for the determination of trace amounts of tetracyclines is proposed based on the chemiluminescence of the KMnO₄ - TCs redox reaction in acidic medium in the presence of a sensitizer, OP. The response to the concentration of tetracyclines is linear in the range of 1.00 to 1000 μg mL^?1 with a relative standard deviation < 2.3 % for determination of 50.0 μg mL^?1 of each antibiotic (n = 11). The detection limits for tetracycline, oxytetracycline and chlortetracycline are 0.40, 0.52 and 0.60 μg mL^?1, respectively. The recommended method is suitable for automatic and continuous analysis and has been successfully tested for determination of tetracyclines in commercial formulations. The chemiluminescence intensity was found to be remarkably enhanced when in the presence of OP micellar system; possible reasons for this observed micellar induced enhanced chemiluminescence is given.     

A New Spectrophotometric Method for the Determination of Maneb in Commercial Formulations

Abstract

A new rapid, selective and sensitive method has been developed for the determination of maneb using pyrocatechol-violet(PV) as chelating reagent in the pH range of 7.5–11.0 in the presence of CTAB producing a complex which shows maximum absorption at 640 nm. Working range of the method is 0.2–3.0 μg ml^?1 maneb (manganese ethylenebisdithiocarbamate). The molar absorptivity of the color system is 79600 1 mol^?1 cm^?1 and Sandell's sensitivity is 0.0033 μg cm^?2. The reproducibility of the method has been checked by the 10 replicate analysis of 15 μg of maneb in 10 ml of solution. The method is quite sensitive and has been applied for the determination of maneb in various commercial samples, crops, grains and synthetic samples.     

Post‐chemiluminescence Method of the Determination of Loperamide Hydrochloride in Human Plasma and Pharmaceutical by Using Dichlorofluorescein as Chemiluminescence Reagent

Abstract

A post‐chemiluminescence (PCL) was observed when loperamide hydrochloride solution was injected into the reaction mixture after the finish of CL reaction of alkaline N‐Chlorosuccinimide (NCS) and dichlorofluorescein. Based on this phenomenon, a simple, sensitive and fast flow injection PCL method was established for the determination of loperamide hydrochloride. The possible mechanism for the PCL reaction was discussed via the investigation of the CL kinetic characteristics, the CL spectra, the fluorescence spectra. The PCL intensity responded linearly to the concentration of loperamide hydrochloride in the range 8.0×10^?10 to 6.0×10^?7 g · ml^?1 with a linear correlation of 0.9995. The detection limit was 4×10^?10 g · ml^?1. The relative standard deviation was 2.4% for 4.0×10^?8 g · ml^?1 loperamide hydrochloride (n=11). This method has been applied to the determination of loperamide hydrochloride in human plasma and pharmaceutical samples with satisfactory results.     

A novel sensitized chemiluminescence flow injection system for the determination of adriamycin and mitomycin

A novel chemiluminescence (CL) method was established for two anticancer drugs, adriamycin (ADM) and mitomycin (MMC), based on potassium permanganate oxidation in the presence of formaldehyde. The sensitized CL emission mechanism was developed by comparing the fluorescence emission with CL spectra. Illuminant was the singlet state bi-molecule oxygen, ¹O₂ ¹O₂ (¹Δ_g ¹Δ_g), from ¹O₂ (¹Δ_g) which was produced in the reaction system, and emitted CL spectra at 639 nm or 649 nm. The presence of formaldehyde may accelerate the generation of ¹O₂ (¹Δ_g) and sensitized CL emission. The optimum conditions for CL emission were investigated and optimized. The relationships between the relative CL intensity and the concentration of the studied analytes found to be linear. The detection limit was 3 × 10^?8 g ml^?1 for ADM and 3 × 10^?9 g ml^?1 for MMC. The relative standard deviations are 2.2% and 1.8% for determinations of ADM at 2.0 × 10^?6 g ml^?1 and MMC at 2.0 × 10^?7 g ml^?1, respectively. The proposed sensitized CL system was successfully applied to the determination of ADM and MMC in their injections with satisfactory results.