Super‐atmospheric pressure chemical ionization mass spectrometry

Super‐atmospheric pressure chemical ionization (APCI) mass spectrometry was performed using a commercial mass spectrometer by pressurizing the ion source with compressed air up to 7 atm. Similar to typical APCI source, reactant ions in the experiment were generated with corona discharge using a needle electrode. Although a higher needle potential was necessary to initiate the corona discharge, discharge current and detected ion signal were stable at all tested pressures. A Roots booster pump with variable pumping speed was installed between the evacuation port of the mass spectrometer and the original rough pumps to maintain a same pressure in the first pumping stage of the mass spectrometer regardless of ion source pressure. Measurement of gaseous methamphetamine and research department explosive showed an increase in ion intensity with the ion source pressure until an optimum pressure at around 4–5 atm. Beyond 5 atm, the ion intensity decreased with further increase of pressure, likely due to greater ion losses inside the ion transport capillary. For benzene, it was found that besides molecular ion and protonated species, ion due to [M + 2H]⁺ which was not so common in APCI, was also observed with high ion abundance under super‐atmospheric pressure condition. Copyright © 2013 John Wiley & Sons, Ltd.     

一种用于高场非对称波形离子迁移谱系统的新型敞开式化学离子源

根据高场非对称波形离子迁移谱(FAIMS)系统的要求, 本文提出了一种新型敞开式直流电晕放电化学离子源. 该离子源主要由内线电极、外筒电极和牵引电极组成, 内、外电极半径分别是0.08、2 mm. 筒壁电极上开有对称的4个槽, 用于通入样品和牵引离子. 质谱实验结果表明, 该离子源能够在敞开环境下很好地离子化丙酮、乙醇、苯胺、N,N-二甲基甲酰胺、甲基磷酸二甲酯(DMMP)、乙酸乙酯、甲酸、乙酸、苯酚等正、负电性物质. 静电计测试实验结果说明该离子源能够稳定地产生离子电流. 通过分析不同时刻的谱图发现, 在不同时间点上产生的主要离子相同, 具有很好的稳定性. 利用感应耦合等离子体(ICP)工艺在硅片上加工了该离子源, 从而验证了该结构可以由微机电系统(MEMS)加工技术实现. 该离子源具有体积小、结构简单、无辐射、工作稳定等特点, 不仅可以满足FAIMS系统的要求, 还可用于敞开式质谱、微型质谱仪、离子迁移谱(IMS)等仪器.     

Liquid sampling–atmospheric pressure glow discharge (LS-APGD) ionization source for elemental mass spectrometry: preliminary parametric evaluation and figures of merit

A new, low-power ionization source for the elemental analysis of aqueous solutions has recently been described. The liquid sampling–atmospheric pressure glow discharge (LS-APGD) source operates at relatively low currents (<20 mA) and solution flow rates (<50 μL min⁻¹), yielding a relatively simple alternative for atomic mass spectrometry applications. The LS-APGD has been interfaced to what is otherwise an organic, LC-MS mass analyzer, the Thermo Scientific Exactive Orbitrap without any modifications, other than removing the electrospray ionization source supplied with that instrument. A glow discharge is initiated between the surface of the test solution exiting a glass capillary and a metallic counter electrode mounted at a 90° angle and separated by a distance of ~5 mm. As with any plasma-based ionization source, there are key discharge operation and ion sampling parameters that affect the intensity and composition of the derived mass spectra, including signal-to-background ratios. We describe here a preliminary parametric evaluation of the roles of discharge current, solution flow rate, argon sheath gas flow rate, and ion sampling distance as they apply on this mass analyzer system. A cursive evaluation of potential matrix effects due to the presence of easily ionized elements indicate that sodium concentrations of up to 50 μg mL⁻¹ generally cause suppressions of less than 50%, dependant upon the analyte species. Based on the results of this series of studies, preliminary limits of detection (LOD) have been established through the generation of calibration functions. While solution-based concentration LOD levels of 0.02–2 μg mL⁻¹ are not impressive on the surface, the fact that they are determined via discrete 5 μL injections leads to mass-based detection limits at picogram to single-nanogram levels. The overhead costs associated with source operation (10 W d.c. power, solution flow rates of <50 μL min⁻¹, and gas flow rates <10 mL min⁻¹) are very attractive. While further optimization in the source design is suggested here, it is believed that the LS-APGD ion source may present a practical alternative to inductively coupled plasma sources typically employed in elemental mass spectrometry.     

Ambient desorption/ionization mass spectrometry using a liquid sampling–atmospheric glow discharge (LS-APGD) ionization source

A novel approach to ambient desorption/ionization mass spectrometry (ADI-MS) is described, based on a recently developed liquid sampling–atmospheric pressure glow discharge (LS-APGD) ionization source. The device is essentially unmodified relative to its implementation in elemental mass spectrometry, where the operational space is characterized by low operation power (<10 W) and low solution delivery rates (<50 μL min^?1). In this implementation, the plasma is produced between a Ni anode and an electrolytic liquid (1 M HNO₃) cathode flowing through a glass capillary that is angled towards the sample surface, at a distance of ～2 mm away. Analyte species can be desorbed/ionized from neat solution residues and complex solid samples. The ADI-LS-APGD source is mounted onto the source interface of a Thermo Finnigan LCQ Advantage Max quadrupole ion trap mass spectrometer without modifications to the instrument faceplate or ion optics. Described here is the initial evaluation of the roles of source geometry and working parameters, including electrolytic solution composition and plasma current, on the response of caffeine residues, with preliminary limits of detection based on the relative standard deviation of the spectral background suggested to be on the 10-pg level. Demonstrative spectra are presented for green tea extracts and raw leaves, coffee beans, a dried (raw) tobacco leaf, an analgesic tablet, and paper currency. Versatility is further revealed through the determination of components in common cigarette smoke. In each case, the spectra are characterized by (M?+?H)⁺ species of the expected constituents. The capacity for a single source to perform both in solution and particulate elemental analysis (as shown previously) and ADI of molecular species is unique in the realm of mass spectrometry.     

Corona discharge ion mobility spectrometry for the determination of theophylline and guaifenesin in human serum

This paper describes the determination of theophylline and guaifenesin in human serum using ion mobility spectrometry with positive corona discharge as source ionization. The optimization of parameters that could influence ion mobility spectrometry was investigated. Under optimum conditions (Temperature; injection: 220 and oven: 175 °C, Flow rate; carrier: 300 and drift: 600 mL min^?1, Voltage; corona: 2300 and drift: 7000 V, pulse width: 100 μs), calibration curves were linear in the ranges of 2 to120 and 6 to 120 ng for theophylline and guaifenesin, respectively. The relative standard deviation (n?=?10) was below 12 %. The detection limits were found to be 0.1 ng for theophylline and 0.5 ng for guaifenesin. The recovery results for the theophylline and guaifenesin determination in human serum was about 80 % that indicate the proposed method can be applied for the two drugs analysis in real sample. Furthermore, the proposed method has been evaluated in the simultaneous determination of the two drugs.     

Spatially resolved spectroscopic measurements of a dielectric barrier discharge plasma jet applicable for soft ionization

An atmospheric pressure microplasma ionization source based on a dielectric barrier discharge with a helium plasma cone outside the electrode region has been developed for liquid chromatography/mass spectrometry and as ionization source for ion mobility spectrometry. It turned out that dielectric barrier discharge ionization could be regarded as a soft ionization technique characterized by only minor fragmentation similar to atmospheric pressure chemical ionization (APCI). Mainly protonated molecules were detected. In order to characterize the soft ionization mechanism spatially resolved optical emission spectrometry (OES) measurements were performed on plasma jets burning either in He or in Ar. Besides to spatial intensity distributions of noble gas spectral lines, in both cases a special attention was paid to lines of N₂⁺ and N₂. The obtained mapping of the plasma jet shows very different number density distributions of relevant excited species. In the case of helium plasma jet, strong N₂⁺ lines were observed. In contrast to that, the intensities of N₂ lines in Ar were below the present detection limit. The positions of N₂⁺ and N₂ distribution maxima in helium indicate the regions where the highest efficiency of the water ionization and the protonation process is expected.     

单向气流负电晕放电离子迁移谱的研究及其在爆炸物检测中的应用

基于离子迁移谱的爆炸物探测仪多采用放射性电离源,发展非放射性电离源一直是该技术的研究热点。本研究基于电晕放电原理设计了一种新型负电晕放电电离源结构,结合自行研制的离子迁移谱仪,应用于痕量爆炸物的快速、高灵敏检测。单向气流模式下,对此电离源的气流、放电电压等运行参数进行了系统优化,得到最佳实验条件为：电晕放电电离源结构的电极环孔直径为3 mm,针-环距离为2 mm,放电电压为2400 V,漂气流速为1200 mL/min。在此条件下,避免了放电副产物氮氧化物和臭氧等引发的一系列复杂反应,得到了单一的反应试剂离子O-2(H2O)n。将其应用于爆炸物,如2,4,6-三硝基甲苯(TNT)、硝酸铵(AN)、硝化甘油( NG)、太安( PETN)、黑索金( RDX)等的高灵敏快速直接检测,对TNT的检测限达到200 pg/μL。结果表明,此负电晕放电电离源具有灵敏度高、结构简单、无辐射性、反应试剂离子单一等优点,在爆炸物快速高灵敏检测、公共安全保障等方面具有广阔的应用前景。     

Paper spray ionization with ion mobility spectrometry at ambient pressure

A paper spray ion source was combined with a drift tube operating at ambient pressure for mobility measurements of ions derived from pharmaceutical solutions. Paper spray ionization with solvent alone resulted in a mixture of ions convolved to a single peak with a reduced mobility of 2.19 cm²/Vs in the mobility spectrum. These were mass-identified principally as m/z 157, (MeOH)₂(HCOOH)₂H⁺ and m/z 129, (MeOH)₄(H₂O)H⁺ while pharmaceuticals with nitrogen bases formed MH⁺ product ions. The duration of response was governed by the volume of liquid added to the paper source and was limited by evaporation of solvent in gas at 58 °C venting the drift tube. Quantitative variation was attributed in part to morphologic changes in the tip of the paper spray source. This was associated with mass flow in the electrical discharge and not due alone to cycles of wetting and drying of the paper. Mobility spectra of chlorpromazine in urine, exhibited a single product ion peak and linear response was 30 to 500 ng with an estimated limit of detection of 1.5 ng. Ion flux could be prolonged by continuous addition of liquid and findings portend a combination of paper spray ionization IMS with paper chromatography.     

Determination of Malathion Using Corona Discharge – Ion Mobility Spectrometry with Solid-Phase Microextraction

A corona discharge (CD) ion mobility spectrometer combined with solid-phase microextraction was constructed. The detection limit and stability of the system for malathion detection were improved using a novel sample introduction port through which the sample desorption was performed in high-temperature drift tube and the sample was introduced directly to the ionization area. The working parameters of the distance between CD needle tip and carrier gas outlet, the drift tube and carrier gas temperature, the carrier gas flow, and the voltage on CD needle were selected. When the extraction time for standard malathion was set to 5?min, the detection limit was 0.96?µg?L^?1 based on thrice the baseline noise, the linear range was 50–500?µg?L^?1, the correlation coefficient was approximately 0.9941, and the relative standard deviation was below 10%. Malathion-spiked lake water samples were analyzed using the developed system and the recovery was 92–102%. This method is suitable for the rapid detection of organophosphorus pesticide residues.     

Sensitivity “Hot Spots” in the Direct Analysis in Real Time Mass Spectrometry of Nerve Agent Simulants

Presented here are findings describing the spatial-dependence of sensitivity and ion suppression effects observed with direct analysis in real time (DART). Continuous liquid infusion of dimethyl methyl phosphonate (DMMP) revealed that ion yield “hot spots” did not always correspond with the highest temperature regions within the ionization space. For instance, at lower concentrations (50 and 100 μM), the highest sensitivities were in the middle of the ionization region at 200 °C where there was a shorter ion transport distance, and the heat available to thermally desorb neutrals was moderate. Conversely, at higher DMMP concentrations (500 μM), the highest ion yield was directly in front of the DART source at 200 °C where it was exposed to the highest temperature for thermal desorption. In matching experiments, differential analyte volatility was observed to play a smaller role in relative ion suppression than differences in proton affinity and the relative sampling positions of analytes. At equimolar concentrations sampled at the same position, suppression was as high as 26× between isoquinoline (proton affinity 952 kJ mol^–1, boiling point 242 °C) and p-anisidine (proton affinity 900 kJ mol^–1, boiling point 243 °C). This effect was exacerbated when sampling positions of the two analytes differed, reaching levels of relative suppression as high as 4543.0× ± 1406.0. To mitigate this level of relative ion suppression, sampling positions and molar ratios of the analytes were modified to create conditions in which ion suppression was negligible.     

Preparation of Cu (II) imprinted polymer electrode and its application for potentiometric and voltammetric determination of Cu (II)

The Cu (II) imprinted polymer glassy carbon electrode (GCE/Cu-IP) was prepared by electropolymerization of pyrrole at GCE in the presence of methyl red as a dopant and then imprinting by Cu²⁺ ions. This electrode was applied for potentiometric and voltammetric detection of Cu²⁺ ion. The potentiometric response of the electrode was linear within the Cu²⁺ concentration range of 3.9 × 10^?6 to 5.0 × 10^?2 M with a near-Nernstian slope of 29.0 mV decade^?1 and a detection limit of 5.0 × 10^?7 M. The electrode was also used for preconcentration anodic stripping voltammetry and results exhibited that peak currents for the incorporated copper species were dependent on the metal ion concentration in the range of 1.0 × 10^?8 to 1.0 × 10^?3 M and detection limit was 6.5 × 10^?9 M. Also the selectivity of the prepared electrode was investigated. The imprinted polymer electrode was used for the successful assay of copper in two standard reference material samples.     

New Ni(II) Ion-Selective Electrode Based on the N-S Schiff Base Ligand as Neutral Carrier in PVC Matrix

Abstract

A nickel(II) [Ni(II)] ion-selective electrode was prepared by incorporating a new N-S Schiff base ligand, glyoxal-bis(S-benzyldithiocarbazate) (GBSB), as a neutral carrier into the PVC matrix. The proposed electrode exhibits an excellent near-Nernstian response for Ni²⁺ ions, ranging from 2.8 × 10^?7 to 1.0 × 10^?1 mol/L with a detection limit of 1.2 × 10^?7 mol/L and a slope of 31.9 ± 0.3 mV/dec in pH 4.0 nitrate buffer solution at 25°C. It has an appropriate response time and suitable reproducibility and can be used for at least 3 months. The operational pH range of the proposed electrode is 4.0–7.5. The response mechanism is discussed in view of the alternating current (AC) impedance technique. In addition, the electrode was successfully used as an indicator electrode in potentiometric titration of Ni²⁺ ion and in the direct determination of Ni²⁺ ion in milk power and chocolate samples.     

Highly Sensitive Membrane Electrode Based on a Copper(II)-bis(N-4-Methylphenyl-Salicyldenaminato) Complex for the Determination of Chromate

A highly sensitive polyvinyl chloride (PVC) membrane electrode, based on copper(II)-bis(N-4-methylphenyl-salicyldenaminato) complex, (CuL₂), as a carrier was reported for the determination of chromate ion. The influence of membrane composition, pH, and possible interfering anions on the response of the ion selective electrode was investigated. The sensor exhibited a Nernstian slope of 29.7 mV per decade when the chromate concentration was varied between 2.0 × 10^?7–1.50 × 10^?2 M in a wide pH range (6.0 to 9.0). The detection limit of the ion selective electrode was 9.2 × 10^?8 M. The proposed sensor was used for at least 4 months without any considerable divergence in potential. It was applied as indicator electrode in potentiometric titration of chromate ion with Pb²⁺ and Tl⁺.     

Development of a dielectric barrier discharge ion source for ambient mass spectrometry

A new ion source based on dielectric barrier discharge was developed as an alternative ionization source for ambient mass spectrometry. The dielectric barrier discharge ionization source, termed as DBDI herein, was composed of a copper sheet electrode, a discharge electrode, and a piece of glass slide in between as dielectric barrier as well as sample plate. Stable low-temperature plasma was formed between the tip of the discharge electrode and the surface of glass slide when an alternating voltage was applied between the electrodes. Analytes deposited on the surface of the glass slide were desorbed and ionized by the plasma and the ions were introduced to the mass spectrometer for mass analysis. The capability of this new ambient ion source was demonstrated with the analysis of 20 amino acids, which were deposited on the glass slide separately. Protonated molecular ions of [M + H](+) were observed for all the amino acids except for L-arginine. This ion source was also used for a rapid discrimination of L-valine, L-proline, L-serine and L-alanine from their mixture. The limit of detection was 3.5 pmol for L-alanine using single-ion-monitoring (SIM). Relative standard deviation (RSD) was 5.78% for 17.5 nmol of L-alanine (n = 5). With the advantages of small size, simple configuration and ease operation at ambient conditions, the dielectric barrier discharge ion source would potentially be coupled to portable mass spectrometers.     

Solid-state ion selective electrode based on polypyrrole conducting polymer nanofilm as a new potentiometric sensor for Zn2+ ion

A pencil graphite electrode (PGE) electrodeposited by a polypyrrole conducting polymer doped with tartrazine (termed as PGE/PPy/Tar) was prepared and used as a zinc (II) solid-state ion-selective electrode. For the preparation of the zinc sensor electrode, electrodeposition of a polypyrrole nanofilm was carried out potentiostatically (E _app?=?0.75 V vs SCE) in a solution containing 0.010 M pyrrole and 0.001 M tartrazine trisodium salt. A pencil graphite and Pt wire were used as working and auxiliary electrodes, respectively. The introduced electrode in the current paper can be fabricated simply and was found to possess high selectivity, exhibited wide working concentration range, sufficiently rapid response, potential stability, and very good sensitivity to Zn (II) ion. The sensor electrode showed a linear Nernstian response over the range of 1.0?×?10^?5 to 1.0?×?10^?1 M with a slope of 28.23 mV per decade change in zinc ion concentration. A detection limit of 8.0?×?10^?6 M was obtained. The optimum pH working of the electrode was found to be 5.0.     

Direct Electroanalytical Determination of Fluvastatin in a Pharmaceutical Dosage Form: Batch and Flow Analysis

Abstract

The reduction of luvastatin (FLV) at a hanging mercury-drop electrode (HMDE) was studied by square-wave adsorptive-stripping voltammetry (SWAdSV). FLV can be accumulated and reduced at the electrode, with a maximum peak current intensity at a potential of approximately ?1.26 V vs. AgCl/Ag, in an aqueous electrolyte solution of pH 5.25. The method shows linearity between peak current intensity and FLV concentration between 1.0 × 10^?8 and 2.7 × 10^?6 mol L^?1. Limits of detection (LOD) and quantification (LOQ) were found to be 9.9 × 10^?9 mol L^?1 and 3.3 × 10^?8 mol L^?1, respectively.

Furthermore, FLV oxidation at a glassy carbon electrode surface was used for its hydrodynamic monitoring by amperometric detection in a flow-injection system. The amperometric signal was linear with FLV concentration over the range 1.0 × 10^?6 to 1.0 × 10^?5 mol L^?1, with an LOD of 2.4 × 10^?7 mol L^?1 and an LOQ of 8.0 × 10^?7 mol L^?1. A sample rate of 50 injections per hour was achieved.

Both methods were validated and showed to be precise and accurate, being satisfactorily applied to the determination of FLV in a commercial pharmaceutical.     

Atmospheric pressure chemical ionization of explosives using alternating current corona discharge ion source

The high‐sensitive detection of explosives is of great importance for social security and safety. In this work, the ion source for atmospheric pressure chemical ionization/mass spectrometry using alternating current corona discharge was newly designed for the analysis of explosives. An electromolded fine capillary with 115 µm inner diameter and 12 mm long was used for the inlet of the mass spectrometer. The flow rate of air through this capillary was 41 ml/min. Stable corona discharge could be maintained with the position of the discharge needle tip as close as 1 mm to the inlet capillary without causing the arc discharge. Explosives dissolved in 0.5 µl methanol were injected to the ion source. The limits of detection for five explosives with 50 pg or lower were achieved. In the ion/molecule reactions of trinitrotoluene (TNT), the discharge products of NO_x^? (x = 2,3), O₃ and HNO₃ originating from plasma‐excited air were suggested to contribute to the formation of [TNT ? H]^? (m/z 226), [TNT ? NO]^? (m/z 197) and [TNT ? NO + HNO₃]^? (m/z 260), respectively. Formation processes of these ions were traced by density functional theory calculations. Copyright © 2015 John Wiley & Sons, Ltd.     

Coupling electrospray corona discharge, charge reduction and ion mobility mass spectrometry: From peptides to large macromolecular protein complexes

We present the design and implementation of a home-built point-to-plane corona discharge probe, which rapidly and efficiently charge reduces biological ions generated by electrospray ionization (ESI). The molecules analysed ranged from small peptides such as Glu-fibrinopeptide B (1.5 kDa), small proteins such as myoglobin (16.9 kDa), polymers such as polyethylene glycol (PEG 10 k) which all showed intense singly charged ions; to large native multiprotein complexes such as GroEL (802 kDa) which show a broad range of charge-reduced species. The corona discharge probe operates at atmospheric pressure and was directly interfaced with a standard-ESI or nanoflow-ESI source of quadrupole ion mobility time-of-flight mass spectrometer. The corona discharge probe is completely modular and could potentially be mounted to any commercial or research grade mass spectrometer with an ESI source. The level of charge reduction is precisely controlled by the applied voltage and/or probe gas flow rate and when in operation, results in approximately a 50 % reduction in total ion current. We also present the combination of corona discharge and travelling wave ion mobility and assign helium collision cross-section values (Ω_He) to the charge reduced species of the native protein complex pyruvate kinase. It would appear that the Ω_He of the +20 charge state for pyruvate kinase is approximately 20 % smaller than the +35 charge state. Finally, we discuss the potential benefits and concerns of utilising charge reduced protein species as a means of extending the travelling wave collision cross-section calibration range over that which is already published.     

Preparation of a solid-state ion-selective electrode based on polypyrrole conducting polymer for magnesium ion

In this study, a potentiometric sensor based on a pencil graphite electrode (PGE) coated with polypyrrole doped with Titan yellow dye (PPy/TY) was prepared for potentiometric determination of magnesium ion in aqueous solutions. The structural characteristics of magnesium sensor electrode (PGE/PPy/TYMg) were studied using scanning electron microscopy and Fourier transform infrared along with energy-dispersive spectroscopy. Under the optimal conditions, the electrode reveals a good Nernstian behavior with slope of 28.27 ± 0.40 mV per decade over the concentration range of 1.0 × 10^?5–5.0 × 10^?2 M and a detection limit of 6.28 × 10^?6 M. The potentiometric response of fabricated electrode toward magnesium ion was found to be independent of the pH of the test solution in the pH range of 4.5–8.0. The electrode showed fast response time (<10 s) and good shelf lifetime (>2 months). The prepared magnesium sensor electrode can also be used as an indicator electrode in potentiometric titration of Mg²⁺ with EDTA with distinguished end point. The electrode revealed good selectivity with respect to many cations including alkali, alkaline earth, transition and heavy metal ions. The introduced magnesium electrode was used for measurement of Mg²⁺ ion in real samples without any serious interferences from other ions.     

Keto-to-enol isomerization in the molecular ion of dimethylmethylphosphonate

A mechanism for keto-to-enol isomerization in dimethylmethylphosphonate (DMMP) has been proposed based on deuterium-labeling studies, a model compound and thermodynamic data. An electron ionization study of H/D exchange occurring in CD₃-labeled DMMP suggests that rapid keto-to-enol isomerization occurs in the ion source and a reaction mechanism based on sequential 1,4-H migrations rather than by the direct 1,3-H transfer or by sequential 1,2-H migrations is proposed. The examination of the mass-analyzed ion kinetic energy/collision-induced dissociation spectrum of the methylphosphonic acid molecular ion suggests that keto-to-enol isomerization does not occur for this species and that 1,2- and 1,3-H migrations are not favored. Available thermodynamic data were employed to construct a potential energy surface for keto-to-enol isomerization of the DMMP molecular ion. The thermodynamic data show that the energy barrier to isomerization is below the internal energy required for decomposition of the DMMP molecular ion. Additionally, the ΔH_f° for the intermediate and enolic isbmers are shown to be significantly less than the ΔH_f° for the keto form of the DMMP molecular ion.