Chemiluminescence Determination of Benzoic Acid Using A Solid-Phase Verdigris Reactor

Benzoicacidisacommonadditiveusedwidelyasfoodpreservativeandplasticizer.Itcouldpromoteseverereactiontoallergicpopulationevenatlowconcentrationlevel1.Routinemethodsfortheassayofbenzoicacidincludeschromatographic2-6,spectrophotometry7,8,capillaryelectrophoresis9-13andelectrochemicaltitration14.Stokes15etal.monitoredairbornebenzoicacidbasedonsurface-enhancedRamanscatteringtechniques.Thereisalsoreportonamicrobialsensorusingpseudomonasforbenzoicacidandtheirderivativesinaqua16.Interestofusinglumines…     

痕量碘的四元碱流动注射分光光度法研究粮食中微量碘的测定

本文报道了基于Feigl点滴反应的痕量碘的流动注射分光光度测定方法。在痕量碘存在下,无色氯胺T和四元碱(N,N-四甲基对苯二胺)在醋酸盐介质中发生反应,反应30s时在605nm下测定其蓝色产物的吸光度。在90样/h的采样频率下检出限为0.2μg/L(3σ)。对10μg/L碘标准溶液测定的变异系数为0.6%(n=11)。粮食灰分液中加入5μg/L碘的回收率较好。     

Flow Injection Spectrophotometric Determination of N-Acetylcysteine and Captopril Employing Prussian Blue Generation Reaction

A novel flow injection procedure to determine N-acetylcysteine and captopril in pharmaceutical formulations is proposed. The flow procedure developed was based on oxidation of the analytes by Fe(III) in acidic medium and subsequent reaction of the Fe(II) generated with excess hexacyanoferrate(III) to produce soluble Prussian blue (KFe[Fe(CN)₆]) measured at 700 nm. Detection limits of 1.0 × 10^?5 mol L^?1 and 3.0 × 10^?5 mol L^?1 for N-acetylcysteine and captopril, respectively, were found. The sample throughput was 70 h^?1 for both analytes and the results obtained were in agreement at a 95% confidence level with those obtained using reference methods.     

卡托普利的单扫描示波极谱测定

基于卡托普利在汞电极上有良好的电化学特性,以汞电极为工作电极,高氯酸为支持电解质,用单扫描示波极谱法测定了片剂、尿液及血清中卡托普利含量。结果表明,本法是测定微量卡托普利含量的一种灵敏、快速而简便的方法。     

Flow-Injection Analysis Based on Extraction and Spectrophotometric Determination of Penicillins with Thiazine Dyes

Abstract

A new method for flow-injection analysis (FIA) for the determination of penicillins based on the extraction and spectrophotometric determination of ion associates with selected thiazine dyes (methylene blue, azure A, and azure B) is proposed. The reaction conditions (c_dye = 2 × 10^?4 mol l^?1, c_KCl = 1 mol l^?1, pH ? 6, λ = 635 nm) were found. The factorial design has been carried out to determine the optimum flow conditions. A wide linear dynamic range of calibration curves (5.1–700 µg ml^?1 for penicillin V with all dyes, R = 0.9985) and good repeatability (e.g., relative standard deviation [RSD] = 4.6–0.6% in this concentration range for the reaction with azure B) were found. The detection limit for penicillin V is 1.5 µg ml^?1, and the determination limit is 5.1 µg ml^?1. The maximum analysis rate is 35 samples per h. The practical samples of pharmaceutics were tested. There are no interferences from the additives in pharmaceutics.     

Flow-Injection Spectrophotometric Determination of Hydrazine

A flow-injection spectrophotometric method for the determination of hydrazine is described. The method is based on the inhibitory effect of hydrazine on the reaction of thionine with nitrite in acidic media. The decolorization of thionine by the reaction with nitrite was used to monitor the reaction spectrophotometrically at 602 nm. The variables that affected the reaction rate were fully investigated and the optimum conditions were established. Hydrazine can be determined in the range 2.0–40.0 μg/ml with a limit of detection of 1.0 μg/ml. The relative standard deviation for 10 replicate determinations of 7.0 μg/ml hydrazine is 3.3%. The method is simple, rapid, and widely applicable.     

Flow-Injection Catalytic Spectrophotometric Determination of Trace Amounts of Nitrite

ABSTRACT

A flow-injection catalytic spectrophotometric method is proposed for the determination of nitrite based on its catalytic effect on potassium bromate oxidation of acridine orange in phosphoric acid medium. The reaction is monitored spectrophotometrically by measuring the decrease in absorbance of acridine orange at 491.5 nm coupling with the stopped-flow technique. The calibration curve was linear between 3.4 and 65 ng/mL, and the detection limit was 2.2 ng/mL. Up to 30 samples can be analyzed per hour with a relative precision of ca. 1.9%. The proposed method was successfully applied to the determination of nitrite in waters and food samples with satisfactory results.     

Spectrophotometric Determination of Polyoxyethylene Nonionic Surfactants in Ground Waters Using Triple-Stage Solid-Phase Extraction Followed by an Improved Ferric Thiocyanate Complexation Method

A practical spectrophotometric determination method for polyoxyethylene nonionic surfactants in ground waters was established, which is based on a ferric thiocyanate complexation colorimetric method preceded by a triple-stage solid-phase extraction technique using SCX, SAX, and C18 cartridges interconnected. Cationic and anionic surfactants interfere with the determination and were therefore effectively trapped and isolated by the SCX and SAX solid phases, respectively. Nonionic surfactants (NSs) were finally introduced and concentrated in the C18 cartridge. The analyte was quantitatively eluted from the C18 sorbent, and the residue was subjected to the colorimetric determination. The calibration line was linear (r² = 0.9997) up to 200µgL^–1 of heptaoxyethylenedodecylether when analyzing sample sizes of 100mL. Overall recoveries were 95–97% with an RSD of less than 3%. The method was applied to the analysis of river water, and 6.4µgL^–1 of NSs as heptaoxyethylenedodecylether was found by means of the standard addition method. The proposed method is very practical and features minimum consumption of chemicals.     

Solid-Phase Benzoylation of Phenols and Alcohols in Microwave Reactor: An Ecofriendly Protocol

An efficient solid-phase benzoylation of phenols and alcohols was developed under microwave irradiation. A stoichiometric amount of benzoyl chloride was sufficient to carry out the reaction. This benzoylation features short reaction time, good yields, and easy workup procedures. Furthermore, the scope of the reaction was extended to prepare 3,5-dinitrobenzoyl derivatives of alcohols.     

Determination of Trace Amounts of Palladium(II) by Solid-Phase Spectrophotometry

A simple and sensitive method for solid-phase spectrophotometric determination of palladium(II) at µgL^–1 level based on the reaction product of Pd²⁺ with disodium 1-nitroso-2-hydroxynaphthalene-3,6-disulphonate (Nitroso R salt) previously immobilized on Dowex 1×1 anion exchanger has been developed. The experimental factors (wavelength, pH, amount of resin, concentration of Pd²⁺ solution, volume of solution sample, equilibration time) were optimized. The advantages of this procedure as opposed to solution methods are discussed. The results obtained with synthetic solutions clearly indicate the suitability of the proposed method for real samples analysis.     

Solid-Phase Synthesis of Calcium Carbide in a Plasma Reactor

A laboratory-scale spout-fluid bed reactor with a dc plasma torch was used to study the solid-phase synthesis of calcium carbide. Calcium oxide powder with a mean particle size of 170 m was reacted with graphite powder (130 m). Argon was used to initiate the plasma and hydrogen gas was then added to increase power and raise the plasma jet enthalpy. Experimental results showed that the reaction took place in the vicinity of the plasma jet and that conversion to calcium carbide increased linearly with reaction time. The rate of conversion increased exponentially with plasma jet temperature, indicating that chemical reaction was the controlling mechanism. Microscopic analysis of the solid product showed that calcium carbide was formed around both reactants, and that the reaction followed a shrinking core model. Although melting and agglomeration of partially reacted particles occurred at high temperature, resulting in instability of the bed and impeding the reaction progress, high conversions are expected in a continuous process with optimized reactor design.     

Captopril Electrochemical Oxidation on Fluorine‐Doped SnO2 Electrodes and Their Determination in Pharmaceutical Preparations

A novel application of fluorine‐doped tin oxide (FTO) electrodes is reported in the present work. To this end, the captopril electrochemical oxidation mechanism on FTO electrodes at various pH and its determination in pharmaceutical preparations was investigated. Captopril oxidation on FTO proceeds at pH between 2.0 and 4.0. The study revealed that interferences for captopril determination in pharmaceutical samples was totally suppressed using these electrode materials. Voltammetric survey showed an anodic peak at about 0.375 V (Ag|AgCl) for captopril oxidation, that takes place through an EC process at pH interval 2.0–4.0. The investigation demonstrated that captopril oxidation occurs through protonated species and these electroactive species interact by adsorption on FTO electrodes, with a large heterogeneous rate constant and a mechanism involving 1H⁺/1e^? in the global reaction. Moreover, a captopril sensor based upon FTO electrodes, with a linear range miliMolar, is proposed. These electrodes are promising candidates for the efficient electrochemical determination of captopril in pharmaceutical preparations.     

Flow-Injection Differential Spectrophotometric pH Selectivity System for the Determination of Cyclamate Contaminants

A flow-injection system with differential spectrophotometric detection is proposed for the simultaneous determination of aniline and cyclohexylamine based on their reaction with 1,2-naphthoquinone-4-sulfonate (NQS). The pH is chosen to achieve selectivity since only aniline reacts at acidic pH whereas the two amines are derivatized in basic medium. The flow manifold comprises two reactors and two detection cells for developing and monitoring the reaction under selective and general (non-selective) conditions. A double beam spectrophotometer is used for differential detection, with two flow cells placed in the sample and reference holders. Figures of merit such as sensitivity, linear range, detection limit and precision are established. The evaluation of accuracy using a series of synthetic mixtures indicates overall prediction errors of 3% and 5% for aniline and cyclohexylamine, respectively. The method is applied to the determination of amine impurities in commercial sweeteners. Good concordance between the proposed and the standard chromatographic methods is found.     

Captopril Modified Silver Electrode and Its Application to the Electroanalysis of Hemoglobin

Abstract

Captopril, 1-[(2S)-3-mercapto-2-methyl-1-oxopropyl]-L-Proline, can be deposited onto a silver electrode by a covalent bonding method to give a long-lived and stable chemically modified electrode(CME). Since the CME is prepared with a reaction between captopril and the substrate silver, the CME being prepared by this method is very stable. Furthermore, Hemoglobin(Hb) exhibits excellent voltammetric response at the modified electrode. Differential pulse voltammetric(DPV) measurements of the protein with this CME reveal the existence of a linear relationship between the anodic peak current and the concentration of Hb in the range of 2×10^?6 ～ 5×10^?5 mol/L. The detection limit is 8×10^?7 mol/L and the relative standard deviation of results is 5% for 6 successive determinations at 2×10_-5 mol/L. The determination of Hb for a real example is carried out.     

Determination of the Antibacterial Drug Enrofloxacin by Solid-Phase Spectrofluorimetry

A method for the determination of trace amounts of enrofloxacin based on solid-phase spectrofluorimetry has been developed. The relative fluorescence intensity of enrofloxacin fixed on Sephadex SP C-25 gel was measured directly after packing the gel beads in a 1-mm silica cell, using a solid-phase attachment. The wavelengths of excitation and emission were 277 and 448nm, respectively. The linear concentration range of application was 0.2–4.0ngmL^–1 of enrofloxacin, with a relative standard deviation of 1.2% (for a level of 2.0ngmL^–1) and a detection limit of 0.04ngmL^–1. The method was applied to the determination of enrofloxacin in commercial pharmaceutical formulations and spiked canine serum samples. It was validated using HPLC as a reference method and applying the standard addition methodology. Recovery levels of the method reached 100% in all cases.     

Automated Determination of Captopril by Flow and Sequential Injection Analysis: A Review

The present study intends to present a review of automated methods for the determination of Captopril—an angiotensin converting enzyme (ACE) inhibitor—using flow or sequential injection analysis. The review covers a range of more than fifteen years of published research on this topic (1993–today). The methods are classified according to the detection systems in three categories, namely spectrophotometric, chemiluminescence, and electroanalytical. The principles and main analytical figures of merit of the reported studies are presented and discussed.     

差分脉冲伏安法测定卡托普利

本文基于金电极表面对巯基化合物的吸附作用,提出了一种简便灵敏的测定抗高血压药物卡托普利的新方法.研究了卡托普利在金电极上的伏安响应,优化了差分脉冲伏安法测定卡托普利的实验条件.研究结果表明:在0.217～3.04 mg/L的范围内,卡托普利的氧化峰电流与其浓度呈良好的线性关系,检出限为0.152 mg/L.测定药物中卡...