Atomic Absorption Detector for Liquid-Liquid Chromatography

Abstract

A detector system specific for the measurement of chelating agents and applicable to liquid-liquid chromatography has been developed. A solution containing the chelating agent is passed over a short column of chelating ion exchange resin in the copper form, and directly into the aspirator of a recording atomic absorption spectrophotometer set to measure copper. A quantity of copper proportional to the quantity of the chelating agent is stripped from the column and recorded as a peak. Precision and accuracy compare with normal atomic absorption techniques, with an average mean standard deviation of 3%, and a corresponding accuracy. The detection limit for this method is 5x10-⁷ millimoles of EDTA or NTA. Determinations are rapid and reproducible in solutions having a pH in the range of 4 to 9. The role of interfering ions is considered. The applicability of the method as a specific detector system for liquid-liquid chromatographic separations of chelating agents is discussed. Recovery of chelating agents from solutions with an ionic strength approximating natural fresh waters is demonstrated.     

Preconcentration of copper(II) on immobilized 8-quinolinol in a flow-injection system with an ion-selective electrode detector

A column containing 8-quinolinol, immobilized on porous glass, is used for preconcentration and medium exchange in a flow-injection system with a copper ion-selective electrode detector. The metal ions are bound to the chelating ion exchanger while the anions and inert sample components pass to waste without contacting the electrode. Acid is then injected to elute the ions into a neutralizing buffer passing the electrode. Matrix effects are thus reduced because all measurements are made in the same buffer. The detection limits are 10^?7 and 3 × 10^?8 M copper(II) for sample volumes of 5 and 25 ml, respectively. The maximum throughput is 12 and 5 samples h^?1 for the two stated injection volumes.     

Column Chromatographic Preconcentration of Copper in Alloys and Complex Materials Using 9,10 Phenanthrenequinone Monoxime Supported on Naphthalene

Abstract

A solid chelating compound phenanthrenequinone monoxime PQM) supported on naphthalene provides a rapid and economical means of preconcentration and separation of copper from the aqueous samples. Copper forms a complex with PC:: supported on naphthalene in the column at pH 6.1–8.4 with a flow rate of 1 ml/min. The metal complex and naphthalene are dissolved out from the column with 5 ml of DMF and the absorbance is measured at 470 nm against reacent blank. Beer's law is obeyed in the concentration range 0.6 9.6 μg of copper in 5 ml of DMF. The molar absorptivity and sensitivity are 6.3×10⁴ L mol^?1 cm^?1 and 0.001 μg cm^?2 respectively.     

The development of an automated HPLC system for the determination of trace-metals in concentrated brines and its application to process monitoring

Methodology based on high performance liquid chromatography (HPLC) has been developed for the determination of trace-metals in concentrated brines. Metal ions, (Al, Ba, Ca, Mg, Sr and Zn) were concentrated quantitatively and isolated from the sodium chloride matrix using a chelating ion-exchange column dynamically coated with the chelating dye xylenol orange. The pH dependence of the uptake of the metals was studied. Using the chelating ion-exchange preconcentration column followed by ion chromatography all the metals studied were determined at the low ng ml^–1 level in concentrated brines and linear/workable calibrations were obtained in the concentration range of interest (<100 ng ml^–1). The methodology developed was successfully transferred to an automated on-line monitoring system for the determination of Ba, Ca, Mg and Sr in concentrated feed brines used in the chlor-alkali industry.     

The Analytical Applications of Organic Reagents in Hydrophobic Gel Media

Abstract

The use of hydrophobic gel particles containing an organic solvent solution of chelating agents is described. With the use of a column of such gel particles, it is possible to trap or concentrate metal ions selectively on the gel particles from very dilute aqueous solution. A method for the semi-quantitative determination of trace amount of metal ions is proposed.     

Simultaneous determination of free and EDTA-complexed copper ions by flame atomic absorption spectrometry with an ion-exchange flow-injection system

A simple method is described for the simultaneous determination of free and complexed copper ions in a flow-injection system comprising ion-exchange and flame atomic absorption spectrometry. Sampling rates for 400-μl samples were 90 h^?1. Typical relative standard deviations for the simultaneous determinations were 1.6% for the complexed metal (0.50 μg ml^?1) and 1.0% for the free metal (0.20 μg ml^?1).     

Potentiometric Titration of Trace Concentrations of Penicillamine Using Ion Selective Electrodes

Abstract

Penicillamine (PA) has shown promise as a therapeutic agent in the treatment of rheumatoid arthritis (RA), and a sensitive analytical procedure applicable to physiological fluids is needed. PA is a metal chelating agent which forms very strong complexes with heavy metal ions (e.g., Hg²⁺, Cu²⁺, Pb²⁺). This characteristic has been applied to the analytical problem presented. The method developed is based on potentiometric titration of the ligand with a metal ion solution utilizing for endpoint detection an indicator electrode selective for this metal ion. The procedure described used lead (II) as the titrant and a lead (II) selective electrode. Demonstrated precision was ±2.0% when 7.5 μg PA was determined in 50 ml solution.     

Solid phase extraction studies on cellulose based chelating resin for separation,pre-concentration and estimation of Cu2+and Ni2+

Chelating resins based on biopolymers, specifically cellulose, offers a green analytical method for determination of metal ions at trace levels present in various samples. It offers a fast, accurate and simple method for separation and pre-concentration of metal ions at low concentrations, prior to their determination by instrumental method. Cellulose based chelating resin (CELL-GLY) has been synthesised by immobilising glycine on it. CELL-GLY was used for the determination of trace amounts of Cu²⁺ and Ni²⁺ from aqueous solutions before their determination by FAAS. The preparation of CELL-GLY involves simple steps, based on natural and easily available biopolymer cellulose, which makes its use as chelating resin is a green method. The Cu²⁺ and Ni²⁺ can be quantitatively recovered from the CELL-GLY in the pH range 4.8–6.9 and 6.9-7.8 respectively with a recovery of more than 95% for each of these metal ions. Recovery of these metal ions using CELL-GLY was quantitative up to 35 °C. The detection limits for copper and nickel by FAAS were 1.20 ppb and 1.40 ppb, respectively. The method was successfully employed for the determination of trace amounts of Cu²⁺ and Ni²⁺ in various samples.     

Conditional Stability Constant Determination of Metal-Fulvic Acid Complexes

Abstract

Conditional stability constants for metal complexes of a terrestrial fulvic acid were determined using an ion-exchange chromatography—atomic absorbance spectroscopy method. Employing the Scatchard model, conditional stability constants were determined for the metal (II) fulvic acid complexes of cadminum, copper, lead, nickel, manganese, and zinc. The order of metal binding by the fulvic acid was determined to be: Cu > Ni > Pb > Zn > Cd > Mn. Complexes of weakly bound metal ions were determined with an added metal ion concentration of 2 × 10^–5 M to 1 × 10^–4 M while complexes of strongly bound metal ions were determined with an added metal ion concentration of 1 × 10^–5 M to 8 × 10^–4 M. The fulvic acid concentration was kept constant at 4 × 10^–4 M. The effect of pH and ionic strength on the copper-fulvic acid complex also was investigated.     

Analytical Separation of Copper(II), Cobalt(II) and Nickel(II) Using Polymer Bound Anthrantic Acid

Abstract

The preferential complexing tendency of different nietal ions towards chelating agents anchored on a polymer has been used for separation of transition metals. the anthranilic acid group was anchored on the polymeric cellulose back-bone by successive coupling with trifunctional reagent cyanuric chloride, in diozane medium, at pH 7 and 9–10, respectively. This polymer bound chelating agent was used to separate copper(II), nickel(II) and cobalt(II) in the concentration range 1.0–0.1 mmol/L. the separation of a mixture of two components was quantitative using column chromatography.     

Binding heavy metal ions with polymerized onion skin

Red onion skin is highly effective for binding heavy metal ions from aqueous solutions. Color leaching can be prevented and the physical characteristics of the substrate can be improved by treatment with formaldehyde in an acidic medium. Batch and column experiments have been conducted with Cu²⁺, Cd²⁺, Zn²⁺, Ni²⁺, Hg²⁺, and Pb²⁺. Almost quantitative removal of the metal ions from solution can be achieved by using columns of the treated onion skin. Competition of the various metal ions for the substrate has been investigated. The capacity of the substrate in the majority of the metal ions studied is well above 1 meq/g. The use of polymerized onion skin to remove heavy metal ions from domestic and industrial wastewater to safe levels has been recommended as a cheap and effective alternative for commercial ion-exchange resins.     

Development of ultrasound-assisted emulsification solidified floating organic drop microextraction for determination of trace amounts of iron and copper in water, food and rock samples

A simple and efficient liquid-phase microextraction technique was developed using ultrasound-assisted emulsification solidified floating organic drop microextraction combined with flame atomic absorption spectrometry, for the extraction and determination of trace amounts of iron and copper in real samples. 2-Mercaptopyridine n-oxide was used as chelating agent and 1-dodecanol was selected as extraction solvent. The factors influencing the complex formation and extraction were optimized. Under optimum conditions, an enrichment factor of ~13 was obtained for both iron and copper from only 6.7 mL of aqueous phase. The analytical curves were linear between 40–800 and 20–1,200 μg L^?1 for iron and copper respectively. Based on three SD of the blank, the detection limits were 8.6 and 4.1 μg L^?1 for iron and copper respectively. The relative SDs for ten replicate measurements of 500 μg L^?1 of metal ions were 2.9 and 1.2 for iron and copper respectively. The proposed method was successfully applied for determination of iron and copper in environmental waters and some food samples including chess, rice, honey and powdered milk. Finally, method validation was made using rock certified reference material. A student’s t test indicated that there was no significant difference between experimental results and certified values.     

Copper electrodeposition into ion-exchange materials

Electrodeposition of copper into spherical granules of ion-exchange materials KU-23 and KU-2 out of acid sulfate solutions is studied by a method of cyclic voltammetry. It is discovered that the discharge of copper ions in an ion-exchange matrix is characterized by a cathodic overvoltage that is higher than the overvoltage of the same process on a graphite substrate by 0.08 V, which is most probably connected with a limited mobility of ions localized at fixed groups [RSO ₃ ^? ]. The cyclic voltammogram exhibits an additional cathodic peak in the potential region corresponding to the reduction of single-charged copper ions that form as a result of their accumulation inside pores of the ion-exchange matrix during anodic dissolution of metal deposited previously. It is fixed microscopically that the process of deposition begins at the graphite substrate/ion-exchanger interface and passes into bulk upon the formation of an electron-conducting layer saturated with copper. Preliminary saturation of the ion-exchanger by copper deposited chemically facilitates uniform electrodeposition of copper over the entire volume of pores of the ion-exchange matrix.     

Thin-Layer Chromatographic Separation of Copper and Mercury Chelates

Abstract

Thin-layer chromatographic separation of metal ions has become immensely popular in analytical chemistry in view of its speed, selectivity and applicability at tracer level. Quinoline-2-aldehyde thiosemicarbazone^1,2 was found to form yellow coloured chelates with metal ions such as copper, nickel, zinc, mercury, iron and lead at pH 7.5 and extract into chloroform. This, however reduces the sensitivity of the reagent as a chromogenic agent but the chromatographic run of the chelates on a thin layer of silica gel coated on glass plate increases the specificity and selectivity of the reagent. In this article we propose a method for separation of copper and mercury chelates from binary mixtures containing chelates of zinc, lead, iron and nickel. The method is applicable for analysis of synthetic mixtures and standard samples.     

Speciation of Charged Complexes by Donnan Dialysis

Abstract

The assignment of metal complexes to various regimes on the basis of their dissociation kinetics is one type of metal speciation study. The most common scheme, which involves column ion-exchange as a means of separating free metal ions and metals in the form of highly labile complexes from other forms of metals in the sample, is demonstrated to categorize incorrectly stable, charged complexes such as iron(II) and nickel(II) o-phenanthroline as labile. Donnan dialysis is an alternative ion-exchange method for metal speciation studies. Data are provided which demonstrate that the above complexes are correctly assigned by the Donnan dialysis method. The relative labilities of ethylenediamine and triethylenetetramine complexes of iron (II) and nickel (II) are also correctly determined by Donnan dialysis.     

Sorption investigation on the removal of metal ions from aqueous solutions using chelating terpolymer resin

A novel chelating terpolymer resin has been synthesized from anthranilic acid, phenylhydrazine, and formaldehyde by condensation in glacial acetic acid. The structure of the chelating resin was clearly elucidated by use of a variety of spectral techniques, for example FTIR, and ¹H and ¹³C NMR spectroscopy. The average molecular weight of the terpolymer resin was determined by gel-permeation chromatography. The empirical formula and empirical weight of the resin were determined by elemental analysis. The physicochemical properties of the terpolymer resin were determined. Scanning electron microscopy was used to establish the surface features of the chelating resin. The ion-exchange behaviour of the resin for specific metal ions, viz. Fe³⁺, Co²⁺, Ni²⁺, Cu²⁺, Zn²⁺, and Pb²⁺, was evaluated by a batch equilibrium method. The study was extended to three variations: evaluation of metal ion uptake in the presence of different electrolytes at different concentrations; evaluation of metal ion uptake at different pH; and evaluation of metal ion uptake at different times. Further, the reusability of the resin was also determined to assess the efficiency of the resin after a few cycles of sorption. From the results it was observed that the resin acts as an effective chelating ion-exchanger.     

Physico‐Chemical Studies on Cu(II) Complexes of Acrylate Chelating Polymers

Abstract

Metal chelating polymers containing amide and carboxylic groups were prepared by gamma‐radiation polymerization of acrylic acid (AA) monomers in the presence of polyacrylamide (PAM). The resins obtained were loaded by copper ions and characterized by FT‐IR spectroscopy, electron spin resonance (ESR), thermogravimetric analysis (TGA), and differential scanning calorimetery (DSC). The IR spectra indicated a lower frequencies shift in the carbonyl bands due to copper ion chelation with carbonyl groups in the polymer resins. Also, the IR spectra reveal a splitting in the band at 3600–3200?cm^?1 that due to the coordination of the NH and OH groups with copper ions. The ESR spectrum was anisotropic with hyperfine structure having the following values 2.3808 and 2.07218 for g _∥ and g _⊥, respectively. These spectra for copper ions have square planar coordination with two nitrogen and two oxygen atoms. TGA and DSC studies show that radiation crosslinking and complexation with copper ion increase the thermal stability of PAM–AA resins. Meanwhile, resin complexes with copper ion showed a higher thermal stability than pure resin. The increase in thermal stability may be correlated with the metal ions coordination with NH and OH groups; this coordination prevents the splitting of ammonia and water molecules. Also, the metal ions providing a coordination crosslink between polymer chains could increase thermal stability.     

Determination of Copper in Mineral Waters from Galicia, Spain, by Flame Atomic Absorption Spectrometry Using Preconcentration with Diethyldithiocarbamate Loaded on Silica Gel

Solid phase extraction using sodium diethyldithiocarbamate (DDC) loaded on silica gel has been used for preconcentration of trace amounts of copper from commercial mineral waters prior to its determination by flame atomic absorption spectrometry. The sorption and releasing of copper have been studied under both static and dynamic conditions. A short shaking time is required for quantitative sorption using the batch method, and a high flow-rate (6 ml min⁻¹) can be used in the column method due to the fast sorption and desorption kinetics. The copper concentration found in several mineral waters from Galicia (Spain) ranged from 8.4 to 23.8 μg L⁻¹. There were no significant differences between the solid-phase extraction method and the conventional solvent extraction method which uses DDC as chelating agent.     

Polythiophene-coated Fe3O4 nanoparticles as a selective adsorbent for magnetic solid-phase extraction of silver(I), gold(III), copper(II) and palladium(II)

We have developed a fast method for sensitive extraction and determination of the metal ions silver(I), gold(III), copper(II) and palladium(II). Fe₃O₄ magnetic nanoparticles were modified with polythiophene and used for extraction the metal ions without a chelating agent. Following extraction, the ions were determined by flow injection inductively coupled plasma optical emission spectrometry. The influence of sample pH, type and volume of eluent, amount of adsorbent, sample volume and time of adsorption and desorption were optimized. Under the optimum conditions, the calibration plots are linear in the 0.75 to 100 μg L^?1 concentration range (R²?>?0.998), limits of detection in the range from 0.2 to 2.0 μg L^?1, and enhancement factors in the range from 70 to 129. Precisions, expressed as relative standard deviations, are lower than 4.2 %. The applicability of the method was demonstrated by the successful analysis of tap water, mineral water, and river water.

Removal of humic acid and surfactant interferences in trace metal determinations by differential-pulse anodic stripping voltammetry with use of adsorption and chelate ion-exchanger columns in a flow-injection system

A flow-injection differential-pulse anodic stripping voltammetry (d.p.a.s.v.) method is modified so that interferences from humic acids or surfactants are eliminated. The injected, slightly acidic sample is passed through a silica anion-exchanger column to remove compoundswith a strong tendency to adsorb to the electrode. The sample then passes to a chelate ion-exchange column containing immobilized 8-quinolinol. The metal ions are retained and later eluted with acid into the voltammetric cell. The results show that the interferences from up to 500 mg 1^–1 humic acid or at least 50 mg 1^-1 Triton X-100 can be removed and that the metal ion can be determined in a range similar to that for normal d.p.a.s.v. methods. The complete cycle time for a determination was 12 min.