多壁纳米碳管固相萃取测定水中的有机氯农药

对于水样中的有机氯农药的净化方法主要是采用传统的液液分配的方法,缺点是溶剂使用量和前处理复杂。近年来固相萃取及固相微萃取等技术被应用到水样中的有机污染物的测定。如利用键合在硅胶上的非极性(C18,LC18等)或极性物质(LC-CN,LC-NH2)对水中有机物进行富集,用GDX或XAD自填的固相柱的报道也很多。纳米技术和纳米材料的发展为开发固相萃取材料带来新契机。纳米材料是指尺寸大小在从1～100m之间物质。与普通的块体材料相比,纳米材料具有较大的比表面,因而有可能具有较大吸附容量。纳米材料在环境有机污染物分离富集方面的应用研究才刚刚开始。本文主要就纳米碳管对水样中的有机氯农药进行研究,优化固相萃取条件。     

Analysis of Organochlorine Pesticides by Solid-Phase Microextraction followed by Gas Chromatography-Mass Spectrometry

Solid-phase microextraction (SPME) followed by gas chromatography-mass spectrometry (GC-MS) was optimized for the analysis of hexachlorocyclohexanes, DDD, DDE, DDT and other organochlorine pesticides in aqueous samples. Higher extraction efficiency was observed with the SPME fibre coated with 100 µm polydimethylsiloxane than with the fibres coated with 85 µm polyacrylate or 65 µm polydimethylsiloxane/divinylbenzene. Equilibration times were longer than 60 min, except for the hexachlorocyclohexanes, in spite of rapid stirring of the sample. However, precise quantitative analysis could be performed also under non-equilibrium conditions: i.e. repeatability standard deviations below 20%. Salt addition had a positive effect on the response for the hexachlorocyclohexanes, whereas the extraction of the other analytes was affected negatively. The pH of the sample solution did not influence the extraction efficiency. The desorption was performed for 5 min at 275°C directly in the GC injector. At shorter desorption times or lower temperatures a significant carry-over was observed for the heavier analytes. Generally, detection limits in the ng/L range were obtainable.     

Solid-Phase Microextraction Gas Chromatography for Determination of Some Organophosphorus Pesticides

A simple and rapid solid-phase microextraction (SPME) method is presented based on activated charcoal–PVC fiber for determination of some organophosphorus pesticides from aqueous samples in direct mode SPME. After optimization of the experimental variables affecting SPME of the target compounds from aqueous solutions, the proposed method was applied to determine pesticides in fruit juice. The analytes in this procedure were preconcentrated for 15 min on the SPME fiber and subsequently desorbed by heating the fiber at 200 °C for 5 min in the GC injection port. Separation was on a capillary column GC followed by flame ionization detection. Recoveries of the pesticides studied in aqueous samples ranged 42%–63% and repeatability for all analytes was < 9% for a single fiber. Fiber-to-fiber reproducibility was < 18%.     

Preparation and Characterization of Metolachlor Molecularly Imprinted Polymer Coating on Stainless Steel Fibers for Solid-Phase Microextraction

A molecularly imprinted polymer (MIP) with metolachlor as the template molecule was first coated on the surface of stainless steel fibers through chemical bonding. Despite 12 times repeated coating procedures, a homogenous, porous, and highly cross-linked MIP coating was obtained with thickness of 17.4 µm (RSD of 6.1%). The specific selectivity of MIP coating to metolachlor and three metabolites could be concluded with 4.4, 4.1, 3.9, and 2.9 times higher extraction amounts of metolachlor, hydroxymetolachlor, deschlorometolachlor, and desmethylmetolachlor than that of the NIP coating, respectively, and good extraction capabilities for chloroacetanilide herbicides were found with the MIP-coated SPME stainless steel fiber. For validation, the fiber was applied for the extraction of metolachlor, propisochlor, and butachlor in spiked corn and soybean samples, and the recoveries of 90.7–92.6%, 86.4–87.9, and 85.4–87.5% were obtained, respectively.     

Determination of Trace Copper by Adsorptive Voltammetry Using a Multiwalled Carbon Nanotube Modified Carbon Paste Electrode

A new method for the determination of trace copper was described. A multiwalled carbon nanotube modified carbon paste electrode was prepared and the adsorptive voltammetric behavior of copper‐alizarin red S (ARS) complex at the modified electrode was investigated. By use of the second‐order derivative linear sweep voltammetry, it was found that in 0.04 mol/L acetate buffer solution (pH 4.2) containing 4×10^?6 mol/L ARS, when accumulation potential is 0 mV, accumulation time is 60 s and scan rate is 100 mV/s, the complex can be adsorbed on the surface of the electrode, yielding one sensitive reduction peak at ?172 mV (vs. SCE). The peak current of the complex is proportional to the concentration of Cu(II) in the range of 2.0×10^?11–4.0×10^?7 mol L^?1 with a detection limit (S/N=3) of 8.0×10^?12 mol/L (4 min accumulation). The proposed method was successfully applied to the determination of copper in biological samples with satisfactory results, the recoveries were found to be 96%–102%.     

Self‐Assembly of Platinum Nanoparticle/Multiwalled Carbon Nanotube Multilayer Film on Au Substrate Electrode

A novel approach to assemble multilayer films of Pt nanoparticle/multiwalled carbon nanotube (MWNTs) composites on Au substrate has been developed for the purpose of improving the methanol oxidation efficiency by providing high catalytic surface area. MWNTs were firstly functionalized with 4‐mercaptobenzene and then assembled on an Au substrate electrode. Pt nanoparticles were fabricated and attached to the surface of the functionalized MWNTs subsequently. Thus a layer of Pt/MWNT composites were assembled on the Au substrate electrode. Repeating above process can assemble different layers of film of Pt/MWNTs composites on the Au electrode. Cyclic voltammetry shows that the Au electrode modified with two layers of film of Pt/MWNT composites exhibits high catalytic ability and long‐term stability for methanol oxidation. The layer‐by‐layer self‐assembly technique provides an efficient strategy to construct complex nanostructure for improving the methanol oxidation efficiency by providing high catalytic surface area.     

Non-Isothermal Crystallization of Poly(vinylidene Fluoride)/Multiwalled Carbon Nanotube Composites

Poly(vinylidene fluoride)/multiwalled carbon nanotube (PVDF/MWCNT) composites were prepared by the method of solution blending. The non-isothermal crystallization of PVDF and its composites was investigated by differential scanning calorimetry (DSC). The results showed that the crystallization peaks shifted to lower temperature and the exothermic trace became wider when cooling rate increased for PVDF and its composites. The MWCNTs caused an increase in crystallization temperature and initial crystallization temperature. In addition, the Jeziorny and Mo methods were used to analyze the non-isothermal crystallization kinetics. The results showed that the crystallization rate rose with an increase in cooling rate, however, the MWCNTs decreased the crystallization rates of PVDF.     

自组装金纳米粒子涂层对环境水样中紫外线吸收剂的固相微萃取

以刻蚀不锈钢丝为基体,采用化学沉积法在表面沉积金纳米粒子(AuNPs),修饰一层1,8-辛二硫醇分子后,再自组装一层AuNPs,制备了高强度AuNPs涂层固相微萃取(SPME)纤维,并与HPLC联用,以常用紫外线吸收剂为例,评价了AuNPs-SPME纤维的萃取分离性能。当萃取时间为30 min、温度为55℃、搅拌速率为800 r/min,pH=7时,萃取效果最好。在优化的萃取条件下,所建立的Au NPs-SPME-HPLC法测定4种紫外吸收剂(2-羟基-4-甲氧基二苯甲酮、2-乙基己基-4-(N,N-二甲氨基)苯甲酸酯、2-乙基己基-4-甲氧基肉桂酸酯和2-乙基己基水杨酸)的线性范围为0.004~200μg/L,检出限为0.43~570 ng/L(S/N=3),相对标准偏差(RSD)在1.9%~4.2%(n=5)之间。河水、废水处理厂的废水以及雨水样品中紫外线吸收剂的加标回收率在77.9%~108%之间,RSD为3.1%~8.0%(n=5)。     

有序介孔碳固相微萃取涂层测定水中氯苯类有机污染物

采用溶剂挥发自组装结合提拉法,在石墨纤维表面制备有序介孔碳(Ordered mesoporous cabon,OMC)涂层,并开展其对水中氯苯类有机污染物的固相微萃取(SPME)测定.扫描电镜(SEM)结果显示,制备的OMC涂层完整,与基体结合紧密,厚度约为7μm.透射电镜(TEM)、X射线衍射(XRD)和氮吸附脱附结果证实,OMC涂层具有规整二维六方特征,比表面积和孔容分别为369.7 m2/g和0.28 cm3/g.以氯苯类污染物为分析对象,采用顶空固相微萃取与氢火焰气相色谱联用法对OMC涂层的萃取性能进行全面的评价,优化萃取时间和温度、解吸时间、搅拌速率、离子强度及顶空体积等萃取条件,并与商品化涂层进行比对.结果表明,最佳萃取条件为:萃取时间30 min,萃取温度50℃,脱附时间2 min,盐浓度0.35 g/mL,顶空体积15 mL.在最佳萃取条件下,检出限在0.05～0.15 μg/L之间;在1～1000 μg/L线性范围内,线性关系良好;7次平行样测定的相对标准偏差为4.1％ ～6.4％.制备的OMC涂层的峰面积是商用聚二甲基硅氧烷/二乙烯基苯(Polydimethylsiloxane/divinylbenzene,PDMS/DVB)涂层的2倍,商用聚丙烯酸酯(Polyacrylate,PA)涂层的18倍.将此涂层应用于两种实际水样中,4种氯苯均未检出,添加浓度为20 μg/L时,样品回收率分别为99.4％～114.5％和92.3％～ 97.0％.     

Novel Activated Carbon Fiber Solid-Phase Microextraction for Determination of Benzyl Chloride and Related Compounds in Water by Gas Chromatography–Mass Spectrometry

An activated carbon fiber (ACF) has been developed for use as an extraction fiber in solid-phase microextraction (SPME) and used to determine benzyl chloride, benzyl dichloride, and benzyl trichloride in water samples by headspace (HS) analysis. Experiments showed that ACF has excellent adsorption capacity. Its well-distributed surface makes desorption swift in a GC–MS injector. Several conditions affecting the ACF-SPME procedure, for example adsorption mode, adsorption time and temperature, and desorption time, were optimized. The optimized HS-ACF-SPME method has acceptable linearity, good precision, and reasonable RSD values for the compounds studied. The ACF is, therefore, a promising alternative for SPME.     

Use of Solid-Phase Microextraction to Monitor Gases Resulting from Thermal Plasma Pyrolysis

This paper proposes use of solid-phase microextraction to monitor the gases resulting from thermal plasma pyrolysis, instead of the traditional process using an air-tight syringe. The results confirm that thermal plasma technology can be used to eliminate carbon tetrachloride, because dioxins and furans were not detected. Some chlorinated compounds, for example tetrachloroethylene, hexachloroethane, 1,1,2,3,4,4 hexachloro-1,3-butadiene, 1,2,3,4,5,5-hexachloro-1,3-cyclopentadiene, and octachlorocyclopentadiene were detected, however. The results also confirm that this technique is more efficient than injection by means of an air-tight syringe for monitoring gases formed by the pyrolysis of carbon tetrachloride and enables detection of all viable sample constituents.Revised: 18 December 2003 and 12 February 2004     

亚临界水萃取-固相萃取联用技术对沉积物中有机氯农药的萃取研究

研究了用亚临界水萃取-固相萃取(SBwE-SPE)联用技术萃取湖泊沉积物中的有机氯农药。以活性炭纤维作为固相萃取剂,对亚临界水萃取物进行净化处理。在125℃下亚临界水萃取40min,对六氯环己烷(HCH)的四种异构体：(α-HCH,β-HCH,γ-δHCH,-HCH)和六氯代苯(HCB)的萃取回收率在70％～95％之间。该方法具有简单、快捷、只使用少量有机溶剂等优点。     

南极鲍鱼样品中有机氯农药的测定

报道了中国南极长城站周围及某国的一个排污口的鲍鱼样品中有机氯农药的残留量。测定结果显示鲍鱼样品中有机氯农药的含量HCHs为ND－1.87ng/g，DDTs为ND－6.61ng/g干重，有机氯农药的回收率为46％－75％。     

Application of Solid-Phase Microextraction for the Analysis of Nitropolycyclic Aromatic Hydrocarbons in Water

The present work investigates the applicability of solid-phase microextraction coupled to gas-chromatography mass-spectrometry for the determination of trace amounts of nitropolycyclic aromatic hydrocarbons in water samples. The main parameters affecting solid-phase microextraction (sampling mode, fibre type, sampling time, agitation rate and ionic strength of the aqueous solution) were controlled and the optimal experimental conditions found were: 65-μm polydimethylsiloxane-divinylbenzene fibre immersed for 45 min to 5 mL spiked water samples, stirred at 1250 rpm. The developed solid-phase microextraction method was found to be linear in the concentration range 0.1 to 10 μg L⁻¹, with the detection limits ranging between 0.004 and 0.060 μg L⁻¹ (under the selective ion monitoring mode) and the repeatability varying between 1.7 and 5.9% (n=5). Analysis of spiked tap and well water samples revealed that matrix had little effect on extraction. Overall, it was found that solid-phase microextraction is suitable for the trace analysis of nitropolycyclic aromatic hydrocarbons in water samples. Revised: 14 October and 14 November 2005     

SDE-GC-ECD分析水体中有机氯农药

运用单滴溶剂萃取-气相色谱-微池电子捕获检测器(SDE—GC—μECD)联用技术对水体中有机氯农药进行了分析，优化了影响单滴溶剂萃取的多种因素。该方法除了对P，P′-DDD的线性范围在0．4～4ng／mL之间外，其余的七种目标物(α-666，β-666，γ-666，δ-666，P，P′-DDE，0，P′-DDT，P，P′-DDT)线性范围均在0．04～4．0ng／mL之间，相关系数为0．9976～0．9999，回收率范围为83．3％～96．1％，相对标准偏差为2．1％～7．8％。与传统的液液萃取相比，单滴溶剂萃取不仅准确度、精密度相当，而且还具有省时、省溶剂的优点。     

Sol-Gel Method for the Preparation of Solid-Phase Microextraction Fibers

ABSTRACT

A novel sol-gel method is applied for the preparation of solid-phase microextraction (SPME) fibers. Scanning electron microscopy experiments suggested a porous structure for the poly(dimethylsiloxane) (PDMS) coating. SPME-GC analysis provided evidence that the sol-gel fibers have some advantages, such as high thermal stability, efficient extraction rates, high velocities of mass transfer, and spacious range of application.     

新固相微萃取—气相色谱法分析大气中芳烃物质

用石墨吸附质棒固相微萃取装置吸附、富集大气芳烃污染物，于气相以谱中解吸并分析。实验表明此法具有无溶剂、快速、简便、灵敏等优点，具有很大的实用性。     

Determination of Bisphenol A Using an Electrochemical Sensor Based on a Molecularly Imprinted Polymer-Modified Multiwalled Carbon Nanotube Paste Electrode

A novel electrochemical sensor for bisphenol A was developed through the combination of a molecular imprinting technique with a multiwalled carbon nanotube paste electrode. A molecularly imprinted polymer and nonimprinted polymer were synthesized in the presence and absence of bisphenol A, and then used to prepare the electrode. The bisphenol A imprinted polymer was applied as a selective recognition element in the electrochemical sensor. Differential pulse voltammetry was used to characterize the electrochemical behavior of bisphenol A at the modified electrodes. The results showed that the imprinted sensor had highest response for bisphenol A. Parameters including the carbon paste composition, pH, and adsorption time for the imprinted sensor were optimized. Under the optimized conditions, the differential pulse voltammetry peak current was linear with the concentration of bisphenol A from 0.08 to 100.0 µM, with a detection limit of 0.022 µM. The imprinted sensor for bisphenol A exhibited good selectivity, stability, and reproducibility. This sensor was successfully used for the determination of bisphenol A in real water samples.     

固相微萃取法在环境监测中的应用

固相微萃取技术(SPME)作为一种样品前处理技术,具有方便、快捷、不使用有机溶剂、灵敏、价廉等优点,已被广泛地应用于环境样品的分析。综合评述了采用SPME法对3种环境基质(气态、水体、固态)中的有机物、无机离子等近百余种污染物的监测情况,并对SPME法在环境监测中的应用进行了展望。     

玻璃纤维对碳纳米管填充聚合物/热塑性聚氨酯共混体系导电性能的影响

研究了表面带有环氧基团的玻璃纤维(GF)对聚丙烯(PP)/热塑性聚氨酯(TPU)/多壁碳纳米管(MWCNT)、 聚甲基丙烯酸甲酯(PMMA)/TPU/MWCNT和聚乳酸(PLA)/TPU/MWCNT体系导电性能的影响. 研究结果表明, 未添加GF时, 由于MWCNTs选择性地分布在TPU分散相中, PP/TPU/MWCNT, PMMA/TPU/MWCNT和PLA/TPU/MWCNT材料的导电性能很差; 加入20%的GF使3个体系的电阻率均大幅度下降, 最高下降约13个数量级, 表明填充GF是一种具有普适性的改善以TPU为分散相的共混体系导电性能的有效方法. GF使体系电阻率降低的机理主要是形成了TPU包覆GF结构, 该结构可以看作长径比较高的导电棒, 可以有效协助导电通路的构建; 同时GF还起到了体积占位的作用, 提高了体系中导电组分在基体中的有效浓度.