Modified Screen-Printed Electrode for Potentiometric Determination of Copper(II) in Water Samples

Modified screen printed (SPE) and carbon paste electrodes (CPE) with phenanthroline–tetraphenyl borate ionophore [Phen:TPB] were fabricated for the determination of copper(II). The modified electrodes have linear responses over a wide concentration range (1 × 10^?6–1 × 10^?2 mol·L^?1) of copper(II) ion at 25 °C with divalent cationic slopes of 29.85 ± 0.58 and 29.45 ± 0.81 mV·decade^?1 and exhibit a detection limit of 1 × 10^?6 mol·L^?1 for SPE and CPE. The selectivity coefficient was measured using the match potential method in acetate buffer of pH = 4.2. The modified SPE and CPE sensors show high selectivity and sensitivity for determination of copper(II) and also show stable and reproducible response over a period of five and three months for SPE and CPE sensors, respectively. This method can be used for determination of copper(II) in water, soil, plant and fish tissue samples and the results obtained agreed with those obtained with atomic absorption spectrometer (AAS).     

Highly Sensitive Flow-Injection Chemiluminescence Detection of Carbonyl Compounds in Wine Samples

A modified Trautz–Schorigin reaction, by using tannic acid-H₂O₂ system for the oxidation and determination of two kinds of carbonyl compounds was developed in this paper. It was found that formaldehyde and acetaldehyde could effectively enhance the chemiluminescence signals of tannic acid–H₂O₂ system in alkaline medium. Under optimized conditions, the proposed method has a linear range of 7 × 10^?9–1 × 10^?4 mol L^?1 for formaldehyde and 1 × 10^?8–1 × 10^?4 mol L^?1 for acetaldehyde with detection limits of 9 × 10^?11 and 3 × 10^?10 mol L^?1, respectively. The relative standard deviations for 15 repeated measurements of 1 × 10^?6 mol L^?1 HCHO and CH₃CHO are 1.13% and 1.65%, respectively. Analysis time per sample is 35 seconds. A comparison of results found by the proposed method with those obtained by a standard reference method provided good agreement. The proposed method is simple, rapid, convenient, and sensitive.     

Simultaneous Analysis of Sugars and Polyphenols in Tobacco by CZE with Amperometric Detection Based on a Cu2O/MWCNT-COOH Composite Electrode

A composite electrode was fabricated from Cu₂O powder, carboxyl-functionalized multi-wall carbon nanotubes (MWCNT-COOH), and paraffin oil in the proportions 51:17:32 (w/w). This composite electrode was used for amperometric detection (CZE–AD) in simultaneous capillary zone electrophoretic analysis of chlorogenic acid, rutin, sucrose, glucose, mannose, and fructose in tobacco samples. Under the optimum conditions, the six analytes could be separated in 100 mmol L^?1 NaOH buffer within 30 min. Good linearity was achieved in the range 1 × 10^?7–1 × 10^?4 mol L^?1 for the two polyphenols and 5 × 10^?6–1 × 10^?3 mol L^?1 for the four sugars. The detection limits (S/N = 3) for the polyphenols and sugars were as low as 10^?8 mol L^?1 and 10^?6 mol L^?1, respectively.     

Static and Hydrodynamic Monitoring of Citalopram Based on its Electro-oxidation Behavior at a Glassy-Carbon Surface

Abstract

The electrooxidative behavior of citalopram (CTL) in aqueous media was studied by cyclic voltammetry (CV) and square-wave voltammetry (SWV) at a glassy-carbon electrode. The electrochemical behaviour of CTL involves two electrons and two protons in the irreversible and diffusion controlled oxidation of the tertiary amine group. The maximum analytical signal was obtained in a phosphate buffer (pH = 8.2). For analytical purposes, an SWV method and a flow-injection analysis (FIA) system with amperometric detection were developed. The optimised SWV method showed a linear range between 1.10 × 10^?5–1.20 × 10^?4 mol L^?1, with a limit of detection (LOD) of 9.5 × 10^?6 mol L^?1. Using the FIA method, a linear range between 2.00 × 10^?6–9.00 × 10^?5 mol L^?1 and an LOD of 1.9 × 10^?6 mol L^?1 were obtained. The validation of both methods revealed good performance characteristics confirming applicability for the quantification of CTL in several pharmaceutical products.     

Magnetic nanoparticles grafted with β-cyclodextrin for solid-phase extraction of 5-hydroxy-3-indole acetic acid

We describe the synthesis of ß-cyclodextrin modified magnetic nanoparticles (CD-mNPs) as a material for solid-phase extraction of the cancer biomarker 5-hydroxy-indole-3-acetic acid (5-HIAA) from urine. The CD-mNPs were characterized by TEM, FTIR, and XRD, and the kinetics and adsorption isotherms were studied. The strong interaction between the CD-mNPs and 5-HIAA is the main driving force for recognition and extraction, while the magnetic core of the NPs allows their separation from the sample matrix. Recovery of 5-HIAA from the adsorbent using an adequate solvent regenerated the adsorbent for further use. 5-HIAA was then quantified by fluorometry of its complex with ß-CD. The method works in the 1?×?10^?7 to 1?×?10^?5 mol L^?1 (R² 0.9982–0.9996) concentration range, and the limits of detection (3σ) and quantification (10 σ) of the method are 1.2?×?10^?8 mol L^?1 and 4.01?×?10^?8 mol L^?1 5-HIAA, respectively. The recovery of 5-HIAA from urine samples spiked with 5-HIAA in three concentrations (1.4?×?10^?6, 4.50?×?10^?6 and 1.0?×?10^?5 mol L^?1) are within 63?±?3 %.

A Direct Chemiluminescence Method for the Determination of Prulifloxacin Using Tris-(4,7-Diphenyl-1,10-Phenanthrolinedisulfonic Acid) Ruthenium(II)–Cerium(IV) System

Abstract

A simple, rapid, injection chemiluminescence method is described for the determination of prulifloxacin, a commonly used antibiotic. A strong chemiluminescence signal was detected when a mixture of the analyte and tris-(4,7-diphenyl-1,10-phenanthrolinedisulfonic acid)ruthenium(II) was injected into cerium(IV) sulfate. The chemiluminescence signal is proportional to the concentration of prulifloxacin in the range 4.0 × 10^?8–9.0 × 10^?6 mol L^?1. The detection limit is 1.0 × 10^?8 mol L^?1, and the relative standard deviation is 2.2% (n = 11) for the determination of 8.0 × 10^?7 mol L^?1 prulifloxacin. The proposed method was successfully applied to the determination of prulifloxacin in pharmaceutical preparations in capsules, spiked serum, and urine samples.     

Voltammetric determination of 17α-ethinylestradiol hormone in supply dam using BDD electrode

In this work, a simple method for electroanalytical determination of 17α-ethinylestradiol (EE2) hormone in natural waters was developed using a boron-doped diamond electrode (BDD). The analyses were performed using square wave voltammetry and the parameters were optimized. The results showed a well-defined irreversible oxidation peak (BR buffer 0.1 mol L^?1, pH 8.0) at +0.65 V (vs. Ag/AgCl). The voltammetric results showed also that the oxidation process is controlled by adsorption of species and indicated that there are two electrons involved. The obtained analytical curves for 17α-ethinylestradiol presented good linearity in the concentration range 9.9?×?10^?7 to 5.2?×?10^?6 mol L^?1 in utlrapure water and 7.9?×?10^?7 to 5.2?×?10^?6 mol L^?1 in natural water samples (supply dam). Detection limits (DL) obtained were between 2.4?×?10^?7 and 7.5?×?10^?7 mol L^?1 and quantification limits (QL) between 7.9?×?10^?7 and 2.5?×?10^?6 mol L^?1. The recovery experiments showed values between 86 and 114 % for spiked samples thus indicating the applicability of the electroanalytical methodology to quantify 17α-ethinylestradiol directly in natural water of supply Dam (Billings Dam in Diadema-SP. Brazil), without any preconcentration or derivatization.     

Functionalized manganese-doped zinc sulfide core/shell quantum dots as selective fluorescent chemodosimeters for silver ion

Zinc sulfide quantum dots doped with Mn(II) ions and coated with a shell of zinc sulfide were prepared, and their surface was modified with iminodiacetic acid to form a QDs-conjugate (QDs-IDA). Such modification effectively improves the water-solubility and luminescence quantum yield of the quantum dots. The optical properties and structural features were characterized by photometry, ¹H NMR and fluorescence spectroscopy. The results displayed that QDs-IDA selectively respond to Ag (I) ion in phosphate buffer solution (pH 7.3) in quenching the fluorescence of QDs-IDA. A good linear relationship exists in the concentration range from 5.0?×?10^?7 mol·L^?1 to 4.5?×?10^?6 mol·L^?1 and the detection limit is 2.6?×?10^?7 mol·L^?1. The sensing mechanism was assumed to result from complex formation between the iminodiacetic acid of QDs-IDA and silver (I) ion which promoted photo-induced electron transfer.     

Determination of Catechol by a Laccase Biosensor Based on Silica-Modified Zirconia Nanoparticles

A promising nanotechnological material, zirconia nanoparticles modified with SiO₂, was used as a medium for the immobilization of laccase to construct a novel biosensor that exhibits sensitive amperometric response to catechol in 0.1 mol · L^?1 phosphate buffer (pH 6.0) using cyclic voltammetry. The linear response to catechol was from 1.0 × 10^?6 to 1.0 × 10^?4 mol · L^?1 and the detection limit was 3.5 × 10^?7 mol · L^?1 at a signal-to-noise ratio of 3. The biosensor exhibited good stability, precision, and few interferences.     

Voltammetric Determination of Dopamine in Human Serum and Urine at a Glassy Carbon Electrode Modified by Cysteic Acid Based on Electrochemical Oxidation of L ‐cysteine

Abstract

The voltammetric behavior of dopamine was studied at a glassy carbon electrode modified by cysteic acid, based on electrochemical oxidation of L ‐cysteine. The modified electrode showed strong electrocatalytic activity towards dopamine and good selectivity. In a phosphate buffer solution (pH 7.4), the anodic peak current obtain from the differential pulse voltammetry of dopamine was linearly dependent on its concentration in the range of 5×10^?9 to 4.0×10^?6mol · L^?1, with a detection limit of 2×10^?9mol · L^?1. The low‐cost modified electrode had been applied to the determination of dopamine in human serum and urine samples with satisfactory results.     

RP-LC Determination of Residual Monomers in Polycarboxylate Superplasticizers

A procedure was developed for the determination of residual monomers in polycarboxylate superplasticizer by reversed-phase high performance liquid chromatography. Seven kinds of residual monomers were quantitatively determined on a SinoChrom ODS-BP (C18) column and UV detector at 205 nm. The mobile phases which were used to determine micromolecular monomers were composed of acetonitrile and phosphate buffer solution (0.05 mol L^?1, pH = 3) in the ratio of 8:92 (v/v). While the mobile phases for long side-chain monomers testing were composed of acetonitrile and phosphate buffer solution (0.05 mol L^?1, pH = 6.5) in the ratio of 40:60 (v/v). The linear response ranged from 4.0 × 10^?6?C2.0 × 10^?3 mol L^?1. The detection limit was 0.12 × 10^?5?C0.8 × 10^?5 mol L^?1. Determination of real samples showed that relative standard deviation of high conversion rate samples was 3.1?C8.7% and standard addition recovery ratio was 91.5?C102.8%. While the relative standard deviation of low conversion rate samples was less than or close to 1% and the standard addition recovery ratio was 96.3?C103.1%.     

Determination of Polyethylene Glycol Monoester Acrylate and Polyethylene Glycol Diester Acrylate Using Reversed-Phase High-Performance Liquid Chromatography

A procedure was developed for the determination of polyethylene glycol monoester acrylate (PEGMA) and polyethylene glycol diester acrylate (PEGDA) by reversed-phase high performance liquid chromatographic (RP-HPLC) with UV detector. Sample was well separated on an SinoChrom ODS-BP (C-18) column (200 × 4.6 mm i.d., 5 μm) with mobile phases composed of acetonitrile-phosphate buffer solution (0.05 mol · L^?1 pH = 6.86) in the ratio of 42:58 (v/v). The PEGMA and PEGDA were detected by UV detector at 205 nm, and quantitatively analyzed with an external standard of methyl acrylate. For PEGMA, the linear response ranged from 0.40 × 10^?5 mol · L^?1 to 2.00 × 10^?3mol · L^?1 (r² > 0.999), the detection limit was 0.12 × 10^?5 mol · L^?1, the recovery rate was found to be 93.4%–99.7%. For PEGDA, the linear response ranged from 0.20 × 10^?5 mol · L^?1 to 1.00 × 10^?3mol · L^?1 (r² > 0.999), the detection limit was 0.04 × 10^?5 mol · L^?1, the recovery rate was found to be 99.1% ～ 105.8%. This quantitative method can also be used in the HPLC analysis of other α,β-unsaturated esters.     

Determination of lead(II) in aqueous solution using carbon nanotubes paste electrodes modified with Amberlite IR-120

A new composite electrode is described for anodic stripping voltammetry determination of Pb(II) at trace level in aqueous solution. The electrode is based on the use of multiwalled carbon nanotubes and Amberlite IR-120. The anodic stripping voltammograms depend, to a large extent, on the composition of the modified electrode and the preconcentration conditions. Under optimum conditions, the anodic peak current at around ?0.57 V is linearly related to the concentration of Pb(II) in the range from 9.6?×?10^?8 to 1.7?×?10^?6 mol L^?1 (R?=?0.998). The detection limit is 2.1?×?10^?8 mol L^?1, and the relative standard deviation (RSD) at 0.24?×?10^?6 mol L^?1 is 1.7% (n?=?6). The modified electrode was applied to the determination of Pb(II) using the standard addition method; the results showed average relative recoveries of 95% for the samples analysed.

Voltammetric Determination of Methylparaban in Cosmetics Using a Multi-Wall Carbon Nanotubes/Nafion Composite Modified Glassy Carbon Electrode

A novel voltammetric sensor using multi-wall carbon nanotubes (MWNTs) coupled with Nafion modified glassy carbon electrode (GCE) was developed for the detection of methylparaben (MP). The sensor exhibited good electrocatalytic activity toward the oxidation of MP in the phosphate buffer solution (PBS, pH 6.5). It displayed good sensitivity, repeatability, reproducibility, and long-term stability. Under the optimized conditions, the anodic peak current was linear with the concentration of MP in the range of 3 × 10^?6 mol L^?1 to 1 × 10^?4 mol L^?1. The detection limit was 1 × 10^?6 mol L^?1. The proposed method was successfully applied to determine MP in cosmetics with satisfactory results.     

Fabrication of a new nanocomposite modified carbon paste Al<Superscript>3+</Superscript>-ion selective electrode based on <Emphasis Type="Italic">N,N</Emphasis>′-dipyridoxyl (1,2-cyclohexanediamine) (PYCA) as an active material

Construction and feature of a nanocomposite modified carbon paste electrode for aluminum(III) ion determination based on N,N′-dipyridoxyl (1,2-cyclohexanediamine) (PYCA) as a novel selector material will be covered by this paper. The optimum composition, Nernstian slope/linear range/detection limit in the forms of calibration graph, response time, utilizable pH range, repeatability and precision of measurements of the aluminum(III) ion using the new fabricated Al³⁺-CPE was evaluated. The optimal composition which performed over Al⁺³ ion concentration range 1.0 × 10^?8 mol L^?1–1.0 × 10^?1 mol L^?1 with near-Nernstian slope equal 20.9 ± 0.2 mV decade^?1 and low detection limit about 5.0 × 10^?9 mol L^?1, was formed of ionophore (PYCA 3 %), binder (paraffin oil 30 %), modifier [multi-wall carbon nanotubes (MWCNTs) 1 %] & [Nanosilica (NS) 0.5 %], and inert matrix (graphite powder 65.5). The request time to give rise Nernstian response of electrode for concentrations from 1.0 × 10^?8 mol L^?1 to 1.0 × 10^?1 mol L^?1 of Al³⁺ ion solution was estimated about ~6 s. The new Al³⁺-CPE was applied in pH range 2.0–5.0 with no consequential change in potential response. To verify the selectivity of electrode toward aluminum(III) ion in the presence of different metallic cations, matched potential method was used. The obtain results in analytical applications reflect the excellent ability of this electrode to play the role as endpoint indicator electrode in both titration and direct potentiometric measurements.     

Modified Glassy Carbon Electrode with Multiwall Carbon Nanotubes as a Voltammetric Sensor for Determination of Leucine in Biological and Pharmaceutical Samples

Abstract

A simple and highly sensitive method is described for voltammetric determination of leucine in blood and urine samples; namely, a glassy carbon electrode with an effective method is modified with multiwall carbon nanotubes (MWNTs). The cyclic voltammetric results indicated that MWNTs remarkably enhanced electrocatalytic activity toward the oxidation of leucine. Under the optimum condition the calibration curve was linear in the concentration range 9.0 × 10^?6 ? 1.5 × 10^?3 mol L^?1, with the detection limit of 3.0 × 10^?6 mol L^?1 and a relative standard deviation (RSD%) lower than 3.0% (n = 5). Also, some kinetic parameters were determined and a multistep mechanism for oxidation of leucine was proposed.     

Chitosan‐Based Glucose Oxidase Electrodes Enhanced by Silver Nanoparticles

Silver nanoparticles enhanced glucose oxidase electrodes were prepared on the basis of chitosan matrix. The enzyme electrodes exhibited high sensitivity and excellent response performance to glucose with a linear range from 1×10^?6 to 8×10^?3 mol · L^?1. And the time reaching the steady‐state amperometric response was less than 5 seconds. The inhibition percentage of this enzyme electrode against copper ions concentration was linear ranging from 1.2×10^?6 to 5×10^?5 mol · L^?1. These properties of enzyme electrodes are probably due to the excellent electron transfer of silver nanoparticles and the orientation of glucose oxidase molecule.     

Molecular imprinting polymer electrosensor based on gold nanoparticles for theophylline recognition and determination

An electrochemical sensor for theophylline (ThPh) was prepared by electropolymerizing o-phenylenediamine on a glassy carbon electrode in the presence of ThPh via cyclic voltammetry, followed by deposition of gold nanoparticles using a potentiostatic method. The effects of pH, ratio between template molecule and monomer, number of cycles for electropolymerization, and of the solution for extraction were optimized. The current of the electro-active model system hexacyanoferrate(III) and hexacyanoferrate(IV) decreased linearly with successive addition of ThPh in the concentration range between 4.0?×?10^?7?~?1.5?×?10^?5 mol·L^?1 and 2.4?×?10^?4?~?3.4?×?10^?3 mol·L^?1, with a detection limit of 1.0?×?10^?7 mol·L^?1. The sensor has an excellent recognition capability for ThPh compared to structurally related molecules, can be regenerated and is stable.

A Flow Injection Chemiluminescence Method for the Determination of Protein Using Copper(II)-Alizarin Red S Complex as an Efficient Chemiluminescent Probe

A sensitive flow injection chemiluminescence (CL) method is proposed for the determination of bovine serum albumin (BSA) using Copper(II)-Alizarin Red S (ARS) complex as an efficient chemiluminescent probe. The detection is based on the binding of the copper(II)-ARS complex to proteins and the catalytic activity of copper(II)-ARS in the luminol-H₂O₂ CL system. Under the selected conditions, the CL intensity is linear with the concentration of BSA in the range of 5.0 × 10^?11 to 1.0 × 10^?9 mol · L^?1. The detection limit was 2.0 × 10^?11 mol · L^?1. The method is successfully applied to the determination of protein in urine.     

Effect of silver nanoparticles concentration on the metal enhancement and quenching of ciprofloxacin fluorescence intensity

Concentration effect of silver nanoparticles (AgNPs) on the photophysical properties of ciprofloxacin (Cip) have been investigated using optical absorption and fluorescence techniques. When performed AgNPs solution was added to the Cip solution, metal-enhanced fluorescence intensity and a blue-shift of 20 nm in the maximum emission spectra of Cip has been observed. The enhanced intensity of this system is strongly dependent on the AgNPs concentration and largest at the 6.0 × 10^?6 mol L^?1. With increase of AgNPs concentration, quenching of fluorescence is observed. Stern–Volmer quenching constants have been calculated at four temperatures. The results show the quenching constants are directly correlated with temperature. It indicates the quenching mechanism is the dynamic quenching in nature rather than static quenching. From which we determined the activation energy for the quenching of Cip-AgNPs to be about 31.1 kJ mol^?1. In addition, in the presence of optimum AgNPs concentration, a sensitive fluorimetric method for the determination of ciprofloxacin at the range 5.0 × 10^?7–3.0 × 10^?5 mol L^?1 and the detection limit of 2 × 10^?8 mol L^?1 in solution is proposed.