Fabrication and Characterization of LaF3/Titania Nanotube Array Electrode for Determination of Fluoride Using a Headspace Single-Drop Microextraction System

LaF₃/titania nanotube array (TNAs) electrodes were fabricated by electrodeposition of LaF₃ on synthesized TNAs. The electrode was characterized by scanning electron microscope (SEM), X-ray diffraction (XRD), and energy dispersive X-ray spectrometer (EDS). The electrode exhibited excellent response to fluoride ion. The linear calibration range achieved four orders of magnitude of F^- concentration (10^?6–10^?2 mg/ml) and the sensitivity of the electrode is higher than that of ordinary fluoride ion selective electrodes (mode PF-1). The limit of detection (LOD) was estimated to be 4.39 × 10^?7 mg/ml (S/N = 3). The novel electrode was applied to the determination of trace fluoride ions in tap water and toothpaste. Finally, a headspace single-drop microextraction (SDME) system coupled with LaF₃/TNAs electrode was successfully applied to determine fluoride in milk samples. The results are satisfactory with an average relative standard deviation (RSD %) of 0.51% and recovery from 96.3% to 107.3%.     

Preparation of a new solid state fluoride ion selective electrode and application

A new solid state fluoride ion selective electrode composed of 70% Ag₂S, 10% Cu₂S and 20% CaF₂ has been developed. An analytically useful potential change occurred, from 1 × 10⁻⁶ to 1 × 10⁻¹ M fluoride ion. The slope of the linear portion (1 × 10⁻¹-1 × 10⁻⁵ M) was about 26 ± 2 mV/10-fold concentration changes in fluoride. It was found that pH change between 1 and 8 had no effect on the potential of the electrode. There was no interference of most common cations such as K^+, Na⁺, Ca²⁺ and Mg²⁺ and anions such as Cl⁻, NO₃⁻, SO₄²⁻ and PO₄³⁻. The lifetime of the electrode was more than 2 years, when used at least 4-5 times a day, and the response time was about 60 s.The measurements were made at constant ionic strength (0.1 M NaNO₃) and at room temperature. This electrode has been used for the determination of fluoride ion in Ankara city tap water and in bottled spring water using standard addition method. The validation of the electrode has been made with a commercial fluoride ion selective electrode (Orion) and high consistency was obtained.     

Enhancement of Demasking of Fluoride Ion From its Aluminum Complexes by Dilution in the Determination With a Fluoride Ion-Selective Electrode

Abstract

In the determination of fluoride ion with an ion-selective electrode the permissible concentration of aluminum increases markedly with decreasing the fluoride concentration in 0.5M citrate buffer solutions at pi I 6. As the accuracy is constant over a concentration range down to 10^?5 M F^? where a Nernstian relation holds fluoride determinations can be accomplished by the successive dilution method. The dilution steps are repeated until the last two results are in agreement, while the concentration of citrate is kept constant. As the ionic strength is kept constant with citrate, the addition of sodium chloride to the buffer is not necessary. Several samples, especially glasses, have been analyzed successfully.     

Differential-pulse polarographic determination of chromium and nickel in zircaloys using microsamples

Three methods were developed for the analysis of the alloying elements chromium and nickel in Zircaloy-2 and Zircaloy-4, alloys of zirconium used extensively in the nuclear industry as nuclear fuel sheathing. Zircaloy was dissolved in hydrofluoric acid followed by oxidation of Cr(III) to Cr(VI) by perchloric acid. The polarographic peak of CrO ₄ ^2– in alkaline medium was used to determine Cr. Nickel was determined, after HF dissolution, using the polarographic peak of the nickel-ammonia complex, Ni (NH₃) ₆ ²⁺ . In an alternative method for Ni, the sample was dissolved in HF and the polarographic peak of the nickel-fluoride complex, NiF ₄ ^2– , was used. Careful control of fluoride ion concentration and the pH eliminated the harmful effect of fluoride on the capillary behaviour of the dropping mercury electrode. The detection limits for chromium, nickel-ammonia and nickel-fluoride in Zircaloys were 0.0016, 0.0033, and 0.0041%, respectively.     

Complexation of fluoride anion and its ion pairs with alkali metal cations by tetra-substituted lower rim calix[4]arene tryptophan derivative

Abstract

Selective binding of fluoride anion and its alkali metal cation ion pairs by a fluorescent calix[4]arene (L) derivative bearing tryptophan moieties was studied in acetonitrile at 25 °C. It was found that LF^? and LF₂^2? complexes were formed and their stability constants were determined by means of UV and ¹H NMR titrations. Both amide and indole NH groups were involved in the stabilisation of the fluoride complexes, i.e. L afforded two anion-binding sites. ¹H NMR titrations provided evidence of simultaneous complexation of both Na⁺ cation and fluoride anion resulting in the formation of a ternary NaLF complex. In this ion pair complex, the Na⁺ cation was most probably bound primarily by the calixarene ether and amide oxygen atoms, whereas the indole NH groups interacted with the fluoride ion. A highly favourable ion pairing between Na⁺ and F^– in acetonitrile was studied using potentiometric measurements. The results pointed out the importance of fluoride pairing with alkali metal cations in aprotic organic solvents and the necessity of taking these reactions into account in the course of speciation studies of such solutions.     

Potentiometric Study of Aluminium-Fluoride Complexation Equilibria and Definition of the Thermodynamic Model

Complexation constants of the Al³⁺/F⁻ system were determined at different ionic strengths in a NaClO₄ (1.0, 2.0 and 3.0 mol⋅dm⁻³) ionic medium by means of a potentiometry using two electrode systems: an ion fluoride selective electrode as well as a glass electrode. All the experimentation was performed at 25 °C. The main species in the complexation equilibria were determined as AlF²⁺, AlF₂⁺, AlF₃⁰, AlF₄⁻, AlF₅²⁻ and AlF₆³⁻. The differences found in the complexation constants for the ionic strength considered were explained by the different behavior of the interaction parameters for the AlF _n ³⁻ⁿ species. These parameters were calculated using the Modified Bromley’s Methodology (MBM). The corresponding thermodynamic quantities were also determined. From all the results obtained, it can be concluded that pH, fluoride concentration and ionic strength influenced the distribution of the fluoride-aluminium complexes.     

The formation of flouride complexes of titanium(IV)

The complex formation equilibria between titanium(IV) and fluoride ions have been studied at 25°C in 3 M(Na)Cl ionic medium by measuring, with an ion selective electrode for F^?, the free HF concentration in acid Ti(IV) solutions. The [H⁺] was kept within 0.25 and I M where the predominant form of uncomplexed metal is the dihydroxotitanium(IV) ion, Ti(OH)²⁺₂. The potentiometric data have been explained by assuming Ti(OH)₂F⁺, TiF₄ and HTiF^?₆, with equilibrium constants given in Table 3. Within the accuracy of the present e.m.f. study, ±0.2 mV, no evidence for intermediate complexes bearing 2, 3 and 5 F^? was found.From a special series of measurements, carried out by replacing a large part of the Cl^? with ClO^?₄, it is concluded that no appreciable amount of Ti(IV)Cl complexes is formed at the 3 M level employed as ionic medium.     

Capillary electrophoresis with contactless conductivity detection for the quantification of fluoride in lithium ion battery electrolytes and in ionic liquids—A comparison to the results gained with a fluoride ion‐selective electrode

In this study, an optimized method using capillary electrophoresis (CE) with a direct contactless conductivity detector (C⁴D) for a new application field is presented for the quantification of fluoride in common used lithium ion battery (LIB) electrolyte using LiPF₆ in organic carbonate solvents and in ionic liquids (ILs) after contacted to Li metal. The method development for finding the right buffer and the suitable CE conditions for the quantification of fluoride was investigated. The results of the concentration of fluoride in different LIB electrolyte samples were compared to the results from the ion‐selective electrode (ISE). The relative standard deviations (RSDs) and recovery rates for fluoride were obtained with a very high accuracy in both methods. The results of the fluoride concentration in the LIB electrolytes were in very good agreement for both methods. In addition, the limit of detection (LOD) and limit of quantification (LOQ) values were determined for the CE method. The CE method has been applied also for the quantification of fluoride in ILs. In the fresh IL sample, the concentration of fluoride was under the LOD. Another sample of the IL mixed with Li metal has been investigated as well. It was possible to quantify the fluoride concentration in this sample.     

Application of H-Point standard addition method and multivariate calibration methods to the simultaneous kinetic-potentiometric determination of permanganate and dichromate

Simultaneous kinetic-potentiometric determination of binary mixture of permanganate (MnO₄ ^?) and dichromate (Cr₂O₇ ^2?) by H-point standard addition method (HPSAM), partial least squares (PLS) and principal component regression (PCR) is described. In this work, the difference between the rate of the oxidation reaction of Fe(II) to Fe(III) in the presence of MnO₄ ^? and Cr₂O₇ ^2? formed the basis of the method. The rate of the consumed fluoride ion for making the complex was detected by a fluoride ion selective electrode (FISE). The results show that the simultaneous determination of MnO₄ ^? and Cr₂O₇ ^2? could be conducted in their concentration ranges of 0.5?C10.0 and 0.1?C20.0 ??g ml^?1, respectively. The total relative standard error (RSE) for applying the PLS and PCR methods to 9 synthetic samples was 5.30 and 3.17, respectively in the concentration range of MnO₄ ^?, and 3.30 and 2.04, respectively, in the concentration range of Cr₂O₇ ^2?. In order for the selectivity of the method to be assessed, we evaluated the effects of certain foreign ions upon the reaction rate. The proposed methods (HPSAM, PLS and PCR) were evaluated using a set of synthetic sample mixtures and then applied to the simultaneous determination of MnO₄ ^? and Cr₂O₇ ^2? in different water samples.     

Determination of inorganic anions in mushrooms by ion chromatography with potentiometric detection

A simple method for determination of common inorganic anions in mushroom samples has been developed by using suppressed ion chromatography with a pH detection unit. The detection unit which was constructed in such a way that practically no additional dispersion occurred consisted of a flow-through quinhydrone pH sensor and a small reference electrode. Chromatographic separation was performed in the order F⁻, Cl⁻, NO₂⁻, Br⁻, PO₄³⁻, ClO₃⁻, NO₃⁻, and SO₄²⁻, at room temperature by using Ion Pac AS 9-HC anion exchange column. Anion extracts from dried mushroom samples at room temperature were homogenized and filtered before injection. Under optimized analytical conditions, the detection limits of the method were between 2 × 10⁻⁶ and 3 × 10⁻⁴ M, depending on the anion studied. The results showed that the concentrations of fluoride and bromide in all mushroom samples were below their limit of detection. Nitrite was found to be the lowest abundant ion, while the most abundant ion was sulfate in all the mushroom samples studied.     

Use of lithium perchlorate media in the study of protolytic equilibria

A study of the H⁺/F^– system by fluoride ion-selective electrode potentiometry over a range of ionic strengths in LiClO ₄ gives protolysis constants which differ markedly from those obtained in other media such as NaClO ₄ . This is shown to be consistent with the competitive complexation of the fluoride ion by the lithium ion. An examination of literature data indicates that lithium ion complexation is a general phenomenon and supports the conclusion that LiClO ₄ is not preferable to NaClO ₄ as a swamping electrolyte for the study of protolytic equilibria as has previously been thought.     

Speciation analysis of aluminium and aluminium fluoride complexes by HPIC-UVVIS

The study presents a new analytical method for speciation analysis in fractionation of aluminium fluoride complexes and free Al³⁺ in soil samples. Aluminium speciation was studied in model solutions and soil extract samples by means of high performance ion chromatography (HPIC) with UV-VIS detection using post-column reaction with tiron for the separation and detection of aluminium fluoride complex and Al³⁺ forms during one analysis. The paper presents particular stages of the chromatographic process optimization involving selecting the appropriate eluent strength, type of elution or concentration and quantity of derivatization reagent. HPIC was performed on a bifunctional analytical column Dionex IonPac CS5A. The use of gradient elution and the eluents A: 1 M NH₄Cl and B: water acidified to pH of eluent phase, enabled full separation of fluoride aluminium forms as AlF₂⁺, AlF₃⁰, AlF₄⁻ (first signal), AlF²⁺ (second signal) and form Al³⁺ in a single analytical procedure. The proposed new method HPIC-UVVIS was applied successfully in the quantitative and qualitative analysis of soil samples.     

Sodium Ion-Selective Chalcogenide Glass Electrodes

Abstract

Analytical characteristics and sensing mechanism of sodium ion-selective electrodes based on NaCl-Ga₂S₃-GeS₂ glasses have been investigated. Chalcogenide glass electrodes containing 10 mol.% NaCl in the membrane showed near-Nernstian response in the concentration range from 10-³ to 1 M sodium nitrate solution. These sensors were superior to the conventional pNa oxide glass electrodes in selectivity in the presence of hydrogen ions and in Na⁺ ion sensitivity in fluoride media. Prolonged solution treatment for several days reduces, however, the detection limit of the sensors and the slope of the electrode response. Ionic processes at the membrane surface have been investigated using XPS technique and ²²Na tracer measurements. It was shown that sodium ion-exchange governed Na⁺ ion response of chalcogenide     

Novel reusable sulfate-type zirconium alginate ion-exchanger for fluoride removal

It is still a challenge to eliminate efficiently fluoride ion from groundwater, especially to design and synthesis an adsorbent possessing high adsorption capacity, recyclability and wide pH application conditions. Herein we present millimeter-sized sulfate-type zirconium alginate hydrogel beads with 3D network structure (AHB@Zr-SO₄²⁻) that exhibited a maximum adsorption capacity of 101.3 mg/g with wide pH applicability (pH 3−9). This material have ~2.5 times higher adsorption capacity than that of pure zirconium alginate hydrogel beads (AHB@Zr) and it was ascribed to ion exchange between SO₄²⁻ and F⁻ on the surface of AHB@Zr-SO₄²⁻, which was verified via ion chromatography measurement coupled with X-ray photoelectron spectroscopy (XPS) and Fourier Transform Infrared Spectrometer (FTIR Spectrometer) analysis. Density functional theory (DFT) calculations indicated that the ion exchange process between SO₄²⁻ and F⁻ in AHB@Zr-SO₄²⁻ was energetically favorable than OH⁻ and F⁻ in AHB@Zr. In addition, 310 bed volumes (BV) of effluent was realized via column adsorption of groundwater containing fluoride on AHB@Zr-SO₄²⁻ and indicated that it is a promising candidate for mitigating the problem of fluoride-containing groundwater.     

Potentiometric determination of fluoride in geological and biological samples following pyrohydrolytic decomposition

A method for the determination of fluoride in coal, coal fly ash, phosphate rock, limestone, mineral clay, fossilised materials, oyster tissue and vegetation using pyrohydrolysis for sample decomposition is proposed. A specific apparatus was constructed and the influence of vanadium pentoxide (V₂O₅) as a catalyst for the pyrohydrolysis reaction was investigated. It was verified that V₂O₅ does not influence the release of fluoride from the vegetation, oyster tissue, coal and coal fly ash matrices analysed. However, the catalyst was necessary for the phosphate rock, fossil bone, mineral clay and limestone samples. Certified and noncertified samples were analysed using an ion selective electrode (ISE) for the analyte detection. Precise (relative standard deviation—R.S.D.<7%) and accurate (recovery in accordance to certified values) results were obtained. The limit of quantification (LOQ) of the method was 5.0 μg g⁻¹ of fluoride using 20 mg of sample and a final dilution to 10 ml. The sample frequency was five samples per hour.     

An enzyme electrode based on immobilized arylsulfatase for the selective assay of sulfate ion

An enzyme electrode has been constructed for the assay of sulfate ion based on inhibition of the reaction

The steady-state current arising from oxidation of the product, 4-nitrocatechol, is measured at +0.8 V vs. S. C. E. The competitive inhibition of this reaction by added sulfate ion causes a decrease in this steady-state current in a linear relationship to pSO₄ in the range 2–4. The enzyme arylsulfatase (arylsulfate sulfohydrolase, EC 3.1·6.1) is chemically immobilized in a layer on a platinum electrode. This enzyme electrode also gives linear calibration plots for phosphate ion (10^-2–10^-4 M) based on its competitive inhibition of the above reaction, and for fluoride ion (10^-2–10^-4 M) based on its activation of the reaction. The assay of 4-nitrocatechol sulfate (NCS) in the range 10^-6–10^-4 M is possible. By proper control of the NCS concentration the electrode can be made almost completely specific for sulfate: only molybdate interferes. To establish the best operating conditions for the electrode, the effect of pH on the V_m and K_m were determined.     

Determination of fluoride by radiometric assay of181Hf back-extracted from HTTA in benzene

Determination of fluoride at trace level is important for the specification analysis of nuclear fuel samples. This is generally accomplished by pyrohydrolytic separation followed by ion selective electrode potentiometry. In the present work, a method has been developed for the determination of fluoride by radiometric assay of¹⁸¹Hf back-extracted from thenoyltrifluoracetone (HTTA) in benzene.¹⁸¹Hf back-extracted is proportional to the concentration of fluoride.     

Fluorometric Determination of Trace Amounts of Fluoride Ion Using an Expanded Porphyrin

A highly selective and sensitive method of fluorometry is described for determination of the fluoride ion at the parts per billion level via the ion-pair complex formation of the fluoride ion with an expanded prophyrin [2,23-diethyl-8,17-bis(2-ethoxycarbonylethyl)-3,7,12,13,18,22-hexamethylsapphyrin (H₃sap)]. The ion-pair complex gives out an enhanced fluorescence intensity at 680 nm on excitation at 450 nm. Since the present method is based on a direct reaction of the fluoride ion with the sappyrin, a 200-fold amount of the aluminum (III) ion [10⁻⁴M (M = mol dm⁻³)] and a 2000-fold amount of the iron(III) ion (10⁻³M) over the fluoride ion did not interfere with determination of the fluoride ion at concentrations as low as 5 × 10⁻⁷M in the presence of 1,2-diaminocyclohexane-N,N,N′,N′-teraacetic acid. The proposed method was applied to determination of the fluoride ion in various water samples (tap water, river water, rain water, underground water, and hot spring water) and satisfactory results were obtained.     

Determination of Total and Fluoride Bound Aluminium in Tea Infusions by Ion Selective Electrode and Flame Atomic Absorption Spectrometry

ABSTRACT

Speciation of metallic compunds is important especially for their bioavailability. In this present study fluoride bound aluminium species were determined in tea infusion. Total aluminium was measured using flame atomic absorption spectrometry (FAAS). Free fluoride and total fluoride were measured by fluoride selective ion electrode (FISE) with the assistance of TISAB buffer solution used for adjustment of pH and total ionic strength, and ALCOA buffer solution which decomposes all of the Al-fluoride complexes in solution.

During the studies, the effects of pH and time on the formation of Al-F complexes and interference of some metal ions found in tea infusion such as Al³⁺, Mg²⁺, Fe²⁺, Fe³⁺ and Mn²⁺ on the concentration of free fluoride were investigated. The concentration of each Al-fluoride complexes in tea fusion were determined indirectly by calculation using pF-Mole Fraction Diagram. It was found that 1.13±0.15 mg 1^? of 12.00±0.86 mg 1^? total aluminium is fluoride bound aluminium, which means that appoximately 10% of total aluminium in tea infusion is complexed with fluoride.     

Indirect Spectrophotometric Determination of Fluoride In Water With Zirconium-Spadns By Flow Injection Analysis

Abstract

The zirconium-SPADNS method for the determination of fluoride based on the effect of fluoride ion on the color system (Zr-SPADNS), has been adapted to the continuous flow spectrophotometry. A manifold consisting of two lines was used. the decrease in the absorbance of Zr-SPADNS reagent at 590 nm is linear with fluoride concentration in the range 0.00-3.5 ppm. the method has a detection limit of 0.02 ppm fluoride. At a sampling rate of 50 determinations per hour, the precision was about 1% relative standard deviation. the method is applied to the determination of fluoride in natural water samples. the good agreement between the results obtained by this method and those obtained by a potentiometric method using a fluoride ion-selective electrode, show that the new method is potentially suitable for routine analysis. the effects of reaction conditions, flow parameters, and interferences on the FIA-spectrophotometric signals are reported. amount of interfering ion is present in quantity great enough to produce an error of 0.1 ppm or more, the sample must be distilled¹⁷