Multivariate Analysis for the Classification Differentiation of Brazilian Sugarcane Spirits by Analysis of Organic and Inorganic Compounds

Abstract

Brazilian sugarcane spirits were analyzed to elucidate similarities and dissimilarities by principal component analysis. Nine aldehydes, six alcohols, and six metal cations were identified and quantified. Isobutanol (LD 202.9 µg L^?1), butiraldehyde (0.08–0.5 µg L^?1), ethanol (39–47% v/v), and copper (371–6068 µg L^?1) showed marked similarities, but the concentration levels of n-butanol (1.6–7.3 µg L^?1), sec-butanol (LD 89 µg L^?1), formaldehyde (0.1–0.74 µg L^?1), valeraldehyde (0.04–0.31 µg L^?1), iron (8.6–139.1 µg L^?1), and magnesium (LD 1149 µg L^?1) exhibited differences from samples.     

Separation and Sensitive Analysis of Chlorophenols by MEEKC

A new microemulsion electrokinetic chromatographic method has been established for separation and sensitive analysis of the three chlorophenols 2-chlorophenol, 4-chlorophenol, and 2,4-dichlorophenol. The optimum microemulsion system was 15 mM SDS, 112 mM n-butanol, and 10 mM n-octane in 20 mM sodium tetraborate (pH 9.0). Under the optimum conditions, baseline separation was achieved within 8 min. The method was used for analysis of a real water sample previously pretreated by SPE. The linear ranges, precision of migration time and peak area, and limits of detection (LOD) were in the ranges of 0.5–50 μg L^?1, 4.85–9.75%, 0.49–0.706% (n = 6), and 0.6–1 μg L^?1, respectively, for the three chlorophenols.     

Trace Determination of Manganese in Urine by Graphite Furnace Atomic Absorption Spectrometry and Inductively Coupled Plasma–Mass Spectrometry

This paper describes a simple and sensitive method for the determination of manganese in human urine by graphite furnace atomic absorption spectroscopy (GFAAS), which includes sample preparation by microwave digestion. Matrix modifier combinations, the digestion power, pyrolysis, and atomization temperatures were optimized. A mixture of 5.0 µg Pd(NO₃)₂ and 3.2 µg Mg(NO₃)₂ modifier presented the best performance. The optimal temperatures for pyrolysis and atomization were 1500°C and 1950°C, respectively. The GFAAS method was compared to inductively coupled plasma–mass spectrometry (ICP–MS) for the determination of manganese in urine. Analytical figures of merit for GFAAS and ICP–MS were: accuracy (3.46%, 2.19%), precision (3.61%, 5.84%), LOD (0.109 µg · L^?1, 0.015 µg · L^?1), LOQ (0.327 µg · L^?1, 0.045 µg · L^?1), and recovery (80–100%, 74–89%). Both methods were employed for the determination of Mn in urine and the results were compared statistically.     

Use of ionic liquid based chitosan as sorbent for preconcentration of fluoroquinolones in milk,egg, fish,bovine, and chicken meat samples by solid phase extraction prior to HPLC determination

The possibility of using ionic liquid based chitosan sorbent for the separation and preconcentration of fluoroquinolone antibiotics (marbofloxacin, enoxacin, ofloxacin, ciprofloxacin, and enrofloxacin) has been studied. For this reason, different ionic liquids were prepared and coated on the chitosan sorbent. The conditions of the preconcentration of fluoroquinolones on a microcolumn have been optimized and the extraction efficiencies of the prepared sorbents have been compared. The compounds were eluted with 5 mL of 20% NH₃ (v/v, MeOH) solution and determined by HPLC with diode array and fluorescence detector. The limits of detection were found as 4.23 µ g L^?1 for marbofloxacin, and 1.09 µg L^?1 for enoxacin; 3.23 × 10^?3 µg L^?1 for ofloxacin; 8.39 × 10^?3 µg L^?1 for ciprofloxacin; and 19.50 × 10^?3 µg L^?1 for enrofloxacin. The developed method was applied for the analysis of fluoroquinolone in milk, egg, fish, bovine, and chicken samples and the recoveries were obtained in the range 70–100%.     

Determination of Organotin Compounds in Wine by Microwave-Assisted Extraction and High Performance Liquid Chromatography–Inductively Coupled Plasma Mass Spectrometry

A new analytical procedure for the determination of five organotin compounds in several matrix wine samples is reported. The organotin compounds were extracted by microwave-assisted extraction with n-hexane. Extraction conditions, such as volume of n-hexane required, extraction temperature, and extraction time, were investigated and optimized by an orthogonal array experimental design. The determination of organotin compounds in the final extracts was carried out by liquid chromatography–inductively coupled plasma mass spectrometry. The procedure showed limits of detection between 0.029–0.049 µg · L^?1. The linearity was in the range of 0.5 to 100 µg · L^?1. The precision expressed as relative standard deviation (RSD) was below 9.43%. The developed method was successfully employed to analyze different matrix wine samples, and some analytes were detected at the level of 0.053 to 1.14 µg · L^?1.     

Preparation of a Robust and Sensitive Gold-Coated Fiber for Solid-Phase Microextraction of Polycyclic Aromatic Hydrocarbons in Environmental Waters

A robust gold-coated solid-phase microextraction fiber was rapidly prepared on an etched stainless-steel wire based on chemical deposition. Gold(III) was reduced to produce a mechanically robust fiber with a stable coating. Subsequently, it was applied for solid-phase microextraction of five polycyclic aromatic hydrocarbons in water samples coupled to high performance liquid chromatography with an ultraviolet-visible detector. The preconcentration conditions were optimized, including extraction and desorption time, temperature, stirring rate, and ionic strength. Under the optimized conditions, the calibration graphs were linear in the range from 1 to 500 µg · L^?1 for naphthalene and 0.20–500 µg · L^?1 for phenanthrene, anthracene, fluoranthene, and pyrene. Limits of detection were between 0.016 and 0.22 µg · L^?1 (signal-to-noise ratio = 3). The analysis of water samples showed that the recoveries ranged from 86.0% to 112.9% with relative standard deviations between 2.03% and 11.7%. The fiber coating was sensitive and suitable for the preconcentration and determination of polycyclic aromatic hydrocarbons in environmental waters. Compared with previously reported solid-phase microextraction methods, this device offered easy preparation, low cost, resistance to organic solvents, good stability, and high durability.     

An Ionic Liquid Loaded β-Cyclodextrin-Cross-Linked Polymer as the Solid Phase Extraction Material Coupled with High-Performance Liquid Chromatography for the Determination of Rhodamine B in Food

A novel method for separation and determination of rhodamine B in food samples is described. The work is based on the utilization of an ionic liquid loaded β-cyclodextrin cross-linked polymer coupled with high-performance liquid chromatography for the determination of rhodamine B. The inclusion interaction of the ionic liquid-β-cyclodextrin cross-linked polymer with rhodamine B was studied by FTIR. Under optimum conditions, the preconcentration factor achieved for this method was approximately 20. The linear range, detection limit, and relative standard deviation were 0.80 to 130.0 µg L^?1, 0.09 µg L^?1, and 0.66% (n = 3, concentration = 10.0 µg L^?1), respectively. The technique was successfully applied for determination of rhodamine B in food samples.     

Dispersive Liquid–Liquid Microextraction of Silver Prior to Determination by Microsample Introduction-Flame Atomic Absorption Spectrometry

Abstract

A new simple and sensitive method has been proposed for rapid determination of trace levels of silver in environmental water samples, using dispersive liquid–liquid microextraction (DLLME) prior to its microsample introduction-flame atomic absorption spectrometry. Under the optimum conditions, the linear range was 0.1–7 µg L^?1 and limit of detection was 0.018 µg L^?1. The relative standard deviation for 0.50 and 5.00 µg L^?1 of silver in water sample was 4.0 and 1.7%, respectively. The relative recoveries of silver from tap, well, river, and seawater samples at spiking levels of 1.00 and 5.00 µg L^?1 were in the range of 86.4–98.6%.     

Dabsyl chloride derivatisation of melamine followed by high-performance liquid chromatography determination in water samples

A new and sensitive precolumn derivatisation with dabsyl chloride was developed for the analysis of melamine in water samples by high-performance liquid chromatography (HPLC) with visible detection. Derivatisation with dabsyl chloride leads to improving sensitivity and hydrophobicity of melamine. Under optimum conditions of derivatisation and microextraction, the method yielded a linear calibration curve ranging from 10 to 2000 µg L^?1 with a determination coefficient (R²) of 0.9952. Limit of detection (LOD) and limit of quantification (LOQ) were 2.0 and 6.0 µg L^?1, respectively. The relative standard deviation per cent (RSD%) for intraday and inter-day extraction and determination at 20 and 200 µg L^?1 levels of melamine was less than 8.2% (n = 6). Finally, the proposed method was successfully applied for the determination of melamine in different water samples and satisfactory results were obtained (relative recovery ≥91%).     

Simultaneous Determination of Organotin Compounds in White Wine by Gas Chromatography-Mass Spectrometry

A simple, reliable, and effective analytical method was developed for the simultaneous determination of five organotin compounds (OTCs) including monobutyltin trichloride dibutyltin dichloride tributyltin chloride tetrabutyltin and triphenyltin chloride in white wines. The OTCs were derivatized with sodium tetraethylborate (NaBEt₄), and their derivatives were extracted by liquid-liquid extraction (LLE) into n-hexane. The experimental variables, such as type and volume of extraction solvents, amount of derivatization reagent NaBEt₄ and extraction time were optimized. The determination of ethylated derivatives of OTCs in the final extracts was carried out by gas chromatography-mass spectrometry (GC-MS). Under optimized conditions, good linearity was observed when analytical concentrations were in the range of 0.01–4.0 µg · mL^?1, the linearity correlation coefficients were between 0.9982 and 0.9987, with the LODs in the range of 0.2–3.0 µg · L^?1, and the LOQs varied from 0.6 to 10.0 µg · L^?1. The obtained recoveries were in the range of 78.0–120.0%, with the relative standard deviations equal to or lower than 8.1%. This method was applied to the determination of OTCs in white wines with satisfactory results.     

A SPE-LC-MS/MS Method for the Detection of Low Concentrations of Pharmaceuticals in Industrial Waste Streams

A SPE-LC-MS/MS method was developed and validated for the determination of three active pharmaceutical ingredients [API A (3-([2-(diaminomethyleneamino)thiazol-4-yl]methylthio)-N′-sulfamoyl propanimid amide, API B 5-[(2 R)-2-[2-(2-ethoxyphenoxy)ethylamino]propyl]-2-methoxybenzenesulfonamide hydrochloride, API C 1-azabicyclo[2.2.2]octan-8-yl (1S)-1-phenyl-3,4-dihydro-1H-isoquinoline-2-carboxylate] in the wastewater of a chemical synthesis production facility. The SPE-LC-MS/MS method was validated in actual influent and effluent samples. Linearity, LOD, LOQ, repeatability, intermediate precision, and recovery were determined. An LOQ of 400 μg · L^?1, 1.0 μg · L^?1, and 6 μg · L^?1, repeatability of 2.5% CV, 14.8% CV, and 11.9% CV, intermediate precision of 7.8% CV, 11.0% CV, and 8.7% CV and SPE recovery of 114%, 103%, and 91% was determined for API A, B, and C, respectively, in influent. An LOQ of 400 μg · L^?1, 0.8 μg · L^?1, and 6 μg · L^?1, repeatability of 2.0% CV, 11.0% CV, and 10.9% CV, intermediate precision of 1.7% CV, 6.8% CV, and 10.2% CV and SPE recovery of 116%, 96%, and 115% was established for API A, B, and C, respectively, in effluent. Coefficients of correlation for each analyte were >0.9301 confirming the linearity of the method. The LC-MS/MS method was used for an on-going monitoring program for these pharmaceuticals in wastewater. The method development techniques, validation procedures, and results from real wastewater samples are presented in this paper.     

Custom-Made C18 Column for Simultaneous Determination of Endocrine Disrupting Substances in Water by Diode-Array and Fluorescence Detectors

A C₁₈ stationary phase was synthesized for a custom-made HPLC column. When compared to a commercial C₁₈ column, better chromatographic performances were obtained. This column was successfully applied for simultaneous determination of p,p′-DDT, o,p′-DDT, benzo(a)anthracene, benzo(b)fluoranthene, and benzo(a)pyrene in waters by high performance liquid chromatography coupled with dual detectors (diode array and fluorescence detectors) combined with solid phase extraction. Low method detection limits were obtained, i.e., p,p′-DDT: 0.5 µg L^?1, o,p′-DDT: 1 µg L^?1, benzo(a)anthracene: 2.5 ng L^?1, benzo(b)fluoranthene: 5 ng L^?1, and benzo(a)pyrene: 2.5 ng L^?1. High recoveries that ranged from 82 to 94% were obtained for all compounds.     

Determination of Mycotoxins Using Hollow Fiber Dispersive Liquid–Liquid–Microextraction (HF-DLLME) Prior to High-Performance Liquid Chromatography – Tandem Mass Spectrometry (HPLC - MS/MS)

A modified hollow-fiber-supported dispersive liquid-liquid microextraction (HF-DLLME) method was developed for the determination of aflatoxins and ochratoxin A in food samples. The various parameters affecting the efficiency of extraction, such as pH, salt addition, extraction time, stirring rate, desorption time, type and volume of extractant and disperser solvents were carefully studied and optimized using two step strategies. The linearity of the evaluated results was 0.1 to 30?μg L^?1 for aflatoxins and 0.1 to 20?μg L^?1 for ochratoxin A, with regression coefficients (R²) exceeding 0.9990. The precision was satisfactory with relative standard deviation values less than 11%. The method accuracy was within the recommended range from 70% to 120% and analyte accuracy between 83% and 101%. The limits of detection and quantification were in the range from 0.04 to 0.06?μg L^?1 and 0.08 to 0.13?μg L^?1, respectively, for multi-aflatoxins, and 0.02 to 0.04?µg L^?1 and 0.08 to 0.10?µg L^?1, respectively, for ochratoxin A. The developed method was successfully applied for the determination of mycotoxins in food samples.     

Determination of Veterinary Pharmaceuticals in Production Wastewater by HPTLC-Videodensitometry

An SPE-HPTLC method for simultaneous identification and quantification of seven pharmaceuticals in production wastewater was optimized and validated. The studied compounds were enrofloxacine, oxytetracycline, trimethoprim, sulfamethazine, sulfadiazine, sulfaguanidine and penicillin G/procaine. The method involves solid-phase extraction on hydrophilic-lipophilic balance cartridges with methanol and HPTLC analysis of extracts on CN modified chromatographic plates followed by videodensitometry at 254 and 366 nm. Optimization of chromatographic separation was performed by systematic variation of the mobile phase composition using genetic algorithm approach and the optimum mobile phase composition for TLC separation was 0.05 M H₂C₂O₄:methanol = 0.81:0.19 (v/v). Linearity of the method was demonstrated in the ranges from 1.5 to 15.0 μg L⁻¹ for enrofloxacine, 100–500 μg L⁻¹ for oxytetracycline, 150–600 μg L⁻¹ for trimethoprim, 300–1100 μg L⁻¹ for sulfaguanidine and 100–400 μg L⁻¹ for sulfamethazine, sulfadiazine and penicillin G/procaine with coefficients of determination higher than 0.991. Mean recoveries ranged from 74.6 to 117.1% and 55.1 to 108.0% for wellspring water and production wastewater, respectively. Only sulfaguanidine showed lower results. The described method has been applied to the determination of pharmaceuticals in wastewater samples from pharmaceutical industry.     

Selective Determination of Copper in Water Samples by Atomic Absorption Spectrometry after Cloud Point Extraction

A preconcentration methodology utilizing the cloud point phenomenon is described for the determination of copper by flame atomic absorption spectrometry. The reagent Sulfathiazolylazo resorsin was used as a complexing agent. The preconcentration factor of 25-fold was obtained. The calibration curve is linear in the range of 4–400 µ g L^?1 with a limit of detection of 0.64 µ g L^?1. The relative standard deviation (n = 5, 12 µ g L^?1) was 3.5%. The cloud point is formed in the presence of phenol at room temperature. The method was successfully applied to the determination of copper in water samples and a standard reference material.     

Magnetic Stirring-Assisted Dispersive Suspended Microextraction with Solidification of a Floating Organic Droplet for the Determination of Trace Fungicides in Water and Wine

For the first time, a simple method for magnetic stirring-assisted dispersive suspended microextraction has been developed for the determination of three fungicides (azoxystrobin, diethofencarb, and pyrimethanil) in water and wine samples. The method is based on the solidification of a floating organic droplet coupled with high performance liquid chromatography. In the proposed method, the low toxicity solvent 1-dodecanol was used as the extractant. Both the extraction and phase separation process were performed with magnetic stirring. No centrifugation step was involved. After separating the two phases, the extraction solvent droplet was easily collected through solidification at lower temperature. Important parameters such as the kind and volume of organic extraction solvent, extraction and restoration speed, extraction and restoration time, and salt concentration were optimized. Under the optimal conditions, the limits of detection for the analytes varied from 0.14 to 0.26 µg L^?1. The enrichment factors ranged from 125–200. The linearity ranges were 1–2000 µg L^?1, yielding correlation coefficients (r) higher than 0.9990. The relative standard deviation (n = 6) at two spiked level of 0.2 µg mL^?1 and 4 µg L^?1 varied between 2.2% and 7.8%. Finally, the developed technique was successfully applied to determine target fungicides in real water and wine samples, where the obtained recoveries ranged from 83.8–105.3%     

Determination of Heavy Metal Content in Wild-Edible Mushroom from Jordan

The heavy metal content was investigated for six mushroom species native to Jordan. Metal (Cu, Pb, Cd, Fe, Zn, Mn, Ni, and Co) content in soil substrate and their relation to metal concentrations in mushroom and underlying soil were determined by flame and graphite furnace atomic absorption spectrometry. Mushroom species and soil were collected from different places in Jordan. The highest Cu level was 51.84 µg g^?1 for the species Lepista nuda; whereas, the lowest Cu level was found to be 18.51 µg g^?1 in Calvatia utriformis. Among the wild mushrooms, the highest Pb level was found as 4.81 µg g^?1 in Bovista plumbea, whereas the lowest Pb concentration was 2.01 µg g^?1 in Calvatia utriformis. The highest Cd level was determined as 1.9 µg g^?1 for Lepista nuda, whereas the lowest Cd level was 0.58 µg g^?1 for the species of Polyporus frondosus. The highest Zn level was 58.77 µg g^?1 for the species of Lepista nuda and the lowest Zn concentration was found 35.98 µg g^?1 in Calvatia utriformis. The highest Fe level was found as 317 µg g^?1 in Lepista nuda, whereas the lowest Fe concentration was 211.7 µg g^?1 in Calvatia utriformis. The highest Mn content was 36.55 µg g^?1 for Russula delica, whereas the lowest Mn level was 24.5 µg g^?1 for the species Bovista plumbea. The highest Ni content was found as 12.65 µg g^?1 for Russula delica, whereas the lowest Ni level was 0.17 µg g^?1 for Bovista plumbea. The highest Co content in the tested mushrooms was found as 3.5 µg g^?1 for the species of Agaricus bisporus, whereas the lowest Co level was 0.85 µg g^?1 for Polyporus frondosus. The results indicated that, in general, heavy metal contents in all mushroom species were lower than the underlying soil substrates except for some mushroom species.     

Mercury speciation by a high performance liquid chromatography—atomic fluorescence spectrometry hyphenated system with photo-induced chemical vapour generation reagent in the mobile phase

Speciation of mercury was accomplished by using a simple interface with photo-induced chemical vapour generation in a high performance liquid chromatography—atomic fluorescence spectrometry (HPLC-AFS) hyphenated system. Acetic acid and 2-mercaptoethanol in the mobile phase were used as photochemical reagent. The operating parameters were optimized to give limits of detection of 0.53 µg L^?1, 0.22 µg L^?1, 0.18 µg L^?1 and 0.25 µg L^?1 for inorganic mercury, methylmercury, ethylmercury and phenylmercury, respectively. The method was validated with the certified reference material DORM-2 and applied to the analysis of seafood samples. The HPLC-AFS hyphenated system is simple, environmentally friendly, and represents an attractive alternative to the conventional peroxothiosulfate-borohydride method.     

Flow Injection Chemiluminescence Determination of Retinol and α-Tocopherol in Blood Serum and Pharmaceuticals

A simple and sensitive flow-injection method is reported for the determination of retinol and α-tocopherol in human blood serum and pharmaceuticals. The method is based on the reduction of vanadium(V) by retinol and α-tocopherol and subsequent reaction of reduced vanadium with luminol to generate chemiluminescence signal. The optimized conditions allow a linear calibration range of 30–2850 µg L^?1 and 5–4300 µg L^?1 for retinol and α-tocopherol, with relative standard deviations of 1.2–4.6% and 1.5–5.6%, respectively. The detection limits for retinol and α-tocopherol, defined as three times the standard deviation of measured blanks were 23 µg L^?1 and 2.15 µg L^?1, respectively. The proposed method allowed up to 20 determinations h^?1. The tolerance amount of foreign ions/compounds on the determination of retinol and α-tocopherol was also examined. The method was applied to the determination of retinol and α-tocopherol in human blood serum and pharmaceutical samples using hexane extraction with recoveries in the range of 92 ± 2 to 96 ± 1%, and the results obtained were compared with HPLC reference method.     

Catalyzed Determination of Glucose with a Mimic Enzyme Constructed of Bis‐[‐6‐O‐(‐β‐ethyloic‐butanedioic Acid‐1,4‐ester‐4‐)]β‐Cyclodextrin · Fe3+

Abstract

Catalyzed determination of glucose with mimic glucose oxidase is constructed by the reaction of β‐cyclodextrin, maleic anhydride, and chloroacetic acid with iron trichloride in hydrogen peroxide. The method is simple and convenient, and sensitivity and repeatability are ideal. Beer's law is obeyed in a concentration range of 30–197 µg · ml^?1 glucose with an excellent correlation coefficient (r=0.9994), while the detection limit is 4.10 µg · ml^?1, the RSD is 0.98% (n=8). The recovery of sample is 95.8–103.1%.