聚中性红修饰玻碳电极葡萄糖生物传感器

以中性红为电子媒介体,电聚合于Nafion修饰的玻碳电极表面,以戊二醛作交联剂固定葡萄糖氧化酶,最后覆盖一层Nafion膜防止酶流失,构建一种新型葡萄糖生物传感器.详细探讨了传感器的电化学性能及对葡萄糖的最佳响应条件.结果表明,30℃时,传感器在pH 7.0的PBS中对葡萄糖的线性响应范围为1.0×10-5~5.0×10-3mol.L-1.该传感器制作简单、性能优良,有潜在应用前景.     

聚对氨基吡啶化学修饰电极上酚磺乙胺的电化学行为及其溶出伏安法测定

在玻碳电极上制备了聚对氨基吡啶 (POAP)修饰膜电极 ,并用POAP电极研究了酚磺乙胺 (DIC)的电化学行为。POAP修饰电极对DIC的氧化有良好的电催化活性。循环伏安图上出现一对灵敏、可逆的氧化还原峰。在最佳条件下 ,氧化峰电流与DIC浓度在 4.0× 10 -8～ 1.0× 10 -3 mol/L范围内呈良好线性关系 ,开路富集 5min检测限达 7.6× 10 -10 mol/L。用POAP测定DIC具有良好的重现性、灵敏度和稳定性     

聚吖啶红修饰电极的制备及其应用

扑热息痛;聚吖啶红修饰电极的制备及其应用     

DNA/聚(3,4-乙烯基二氧噻吩)修饰电极的制备及其用于亚硝酸根的电化学行为及测定研究

采用恒电流和电沉积两步法制备了脱氧核糖核酸-聚(3,4-乙烯基二氧噻吩)(DNA-PEDOT)复合膜修饰玻碳电极。用电化学阻抗法(EIS)和循环伏安法(CV)表征了不同修饰电极的修饰可行性和表面的电子传递能力。结果表明,DNA可以牢固地结合在PEDOT膜上,并能改善PEDOT膜的性质。研究了NO2-在DNA-PEDOT修饰电极上的电化学行为,提出了一种新的检测NO2-的电化学方法。在0.1 mol/L pH7.0的磷酸盐缓冲溶液(PBS)中,NO2-在DNA-PEDOT修饰电极上于0.88 V左右出现1个较好的氧化峰,考察了该氧化峰的性质及其影响因素。示差脉冲伏安法(DPV)的结果表明,NO2-的DPV氧化峰电流与其浓度在0.3~1.0、1.0~20、20~100μmol/L 3个范围内呈良好的线性关系,检出限(S/N=3)为60 nmol/L,并考察了可能存在的干扰物质对测定的影响。结果显示,该复合膜修饰电极对NO2-的检测具有良好的稳定性和选择性。将其用于实际样品的检测,结果满意。     

亚铁氰化钾掺杂聚中性红膜修饰电极的制备及电分析特性

对亚铁氰化钾掺杂的聚中性红膜修饰电极的制备及其电化学行为和Ｆｅ（ＣＮ）６４－在该电极上的催化作用进行了研究。结果表明,该修饰电极对Ｆｅ（ＣＮ）６４－存在较强的电催化作用,催化峰电流与Ｆｅ（ＣＮ）６４－的浓度在 １．０×１０－５～２．０×１０－３ ｍｏｌ／Ｌ范围内呈良好的线性关系,检测限可达５×１０－６ｍｏｌ／Ｌ     

聚亚甲基蓝和纳米金修饰玻碳电极的葡萄糖生物传感器

用循环伏安法在玻碳电极上电聚合一层稳定的亚甲蓝聚合物膜,研究了这层膜在0.1mol/L磷酸缓冲溶液(pH7.0)中的电化学性质。用纳米金溶胶与聚乙烯醇缩丁醛(PVB)构成复合固酶基质,采用溶胶-凝胶法固定葡萄糖氧化酶(GOD)于亚甲蓝修饰的玻碳电极表面,制成了新型葡萄糖生物传感器。实验发现,加入纳米金后提高了酶电极对葡萄糖的电流响应,所制备的传感器具有响应快、灵敏度高、稳定性好,对葡萄糖的线性响应范围为1×10-6~3×10-3mol/L,检出限为5×10-7mol/L。并具有抗尿酸、抗坏血酸干扰的特点。     

Application of a Glassy Carbon Electrode Modified with Poly(Glutamic Acid) in Caffeic Acid Determination

Glassy carbon electrodes were coated with films of poly(glutamic acid) (PG), and the modified electrode proved to be very effective in the oxidation of caffeic acid. The performance of the film was also tested with ascorbic acid, coumaric acid, ferulic acid, sinapic acid and chlorogenic acid. At pH 5.6, all the hydroxycinnamic acids yield a higher peak current intensity when oxidized after incorporation in the PG-modified electrode, and only the oxidation of ascorbic acid exhibits overpotential reduction. At pH 3.5 only caffeic and chlorogenic acid are incorporated in the modified electrode and exhibit a well-defined oxidation wave at +0.51 V and +0.48 V, which is the base for their determination. Linear calibration graphs were obtained from 9 × 10⁻⁶ mol L⁻¹ to 4 × 10⁻⁵ mol L⁻¹ caffeic acid by linear voltammetric scan and from 4 × 10⁻⁶ mol L⁻¹ to 3 × 10⁻⁵ mol L⁻¹ by square wave voltammetric scan. The method was successfully applied to the determination of caffeic acid in red wine samples without interference from other hydroxycinnamic acids or ascorbic acid.     

咖啡因和茶碱在聚合物修饰电极上的电化学行为

研究了咖啡因 (CAF)和茶碱 (THEO)在聚对氨基吡啶 (POAP)修饰电极上的电化学行为。POAP电极对CAF和THEO的电氧化反应具有良好的催化能力 ,两反应物的电氧化呈现完全不可逆过程 ,峰电位相差 130mV左右 ,在最佳条件下测定 ,氧化峰电流与它们的浓度在 5× 10 -8～ 1× 10 -5mol/L之间均呈良好的线性关系。CAF和THEO在POAP电极上具有良好的重现性和稳定性 ,用于多种样品中CAF和THEO测定 ,结果令人满意。     

Electrochemical Biosensing of DNA Immobilized Poly(Vinylferrocenium) Modified Electrode

The polymer, poly(vinylferrocenium) (PVF⁺) modified electrode was developed as the first time herein for the improved electrochemical sensing of DNA based on the oxidation signals of polymer and guanine. The morphologies of polymer film and DNA immobilized polymer film were examined using scanning electron microscope (SEM). The electrochemical behavior of polymer modified electrode was investigated by using cyclic voltammetry (CV) and differential pulse voltammetry (DPV) in the absence/presence of DNA. Experimental parameters, such as the polymeric film thickness, the DNA immobilization time, the concentration of buffer solution, pH and DNA concentration were examined in order to obtain more sensitive and selective electrochemical signals. After optimization studies, DNA hybridization was also investigated.     

High Sensitivity and Reproducibility of a Bismuth/Poly(bromocresol purple) Film Modified Glassy Carbon Electrode for Determination of Trace Amount of Cadmium by Differential Pulse Anodic Stripping Voltammetry

This work described a novel type of bismuth/poly(bromocresol purple) film modified glassy carbon electrode (denoted as Bi/Poly(BCP)/GCE) for anodic stripping analysis of trace Cd²⁺. The Bi/Poly(BCP)/GCE was fabricated in situ by depositing simultaneously bismuth and cadmium by reduction at ?1.20 V on the poly(BCP) film using a differential pulse voltammetry. Under the optimum conditions, the anodic stripping peak current response increased linearly with the Cd²⁺ concentrations in a range of 2.0×10^?8–1.0×10^?7 M and 1.0×10^?7–6.0×10^?6 M in 0.1 M NaAc‐HAc buffer solution (pH 5.0) with the detection limit of 6.5×10^?9 M (S/N=3). The Bi/poly(BCP)/GCE performed good reproducibility and high sensitivity. Finally, this proposed method was successfully applied to determine the concentration of Cd²⁺ in water samples.     

多巴胺在聚铬黑T修饰玻碳电极上的电化学行为及其测定

制备了聚铬黑T修饰玻碳电极,研究了多巴胺(DA)在该修饰电极上的电化学行为。实验结果表明,在pH 4.0磷酸缓冲溶液中,聚铬黑T薄膜对多巴胺的电化学氧化具有明显的催化作用。此外,实验中观察到铬黑T膜能分离检测DA、抗坏血酸(AA)和尿酸(UA)三者的电化响应,DA与AA和UA之间的电位差达到210 mV和170 mV。利用差示脉冲伏安法(DPV)测定DA,其线性范围为0.1~200μmol/L,检出限为0.02μmol/L。该法已成功用于DA注射剂的含量分析,结果令人满意。     

聚对氨基苯磺酸修饰电极对桑枝中桑色素的灵敏测定

采用电聚合的方法制备了聚对氨基苯磺酸(PABSA)修饰电极,以循环伏安法和差分脉冲伏安法研究了桑色素在该修饰电极上的电化学行为。PABSA和黄酮类药物桑色素的π-π共轭作用使得桑色素在该修饰电极上产生的氧化峰更加灵敏。实验发现,在pH 7.0的磷酸盐缓冲介质中,桑色素在0.214 V处产生灵敏的氧化峰。在优化实验条件下,采用差分脉冲伏安法对桑色素进行定量测定,桑色素的氧化峰电流与其浓度呈良好的线性关系,线性范围为5.0×10-7~1.0×10-3 mol/L,检出限为1.0×10-7 mol/L。将该修饰电极用于桑枝生物样品中桑色素含量的测定,结果满意。该方法具有灵敏度高、重现性好的特点,且该修饰电极稳定性高,可重复使用。     

聚邻氨基苯甲酸-铜复合薄膜修饰电极的制备及其电化学性能

利用聚合物官能团对金属离子的配位作用,在电极表面原位制备了金属粒子。 首先在玻碳电极（GCE）表面电沉积聚邻氨基苯甲酸(PoABA),再化学吸附铜离子(Cu2+),用水合肼还原得到单质铜(Cu0)。 采用扫描电子显微镜和能谱分析表征了聚邻氨基苯甲酸 铜(PoABA-Cu0)复合薄膜的表面形貌和元素构成,研究了PoABA-Cu0修饰电极的电化学性能,并以其检测了过氧化氢（H2O2）。 结果表明,电极表面被修饰上了一层PoABA-Cu0复合薄膜;制备的修饰电极对H2O2具有良好的电催化性能,在邻氨基苯甲酸的聚合圈数为10、Cu2+的吸附时间为10 min、工作电压为-0.3 V时,该修饰电极对H2O2表现出了最佳的检测性能,其线性浓度范围为5.0×10-5～1.0×10-2 mol/L,灵敏度为96.3 μA·L/(mmol·cm),检测限为5.0×10-5 mol/L,且具有较好的稳定性。     

Ruthenium Hexacyanoferrate (III) Modified Glassy Carbon Electrode for Determination of Captopril

A glassy carbon electrode modified with a ruthenium (III) hexacyanoferrate film was investigated for the determination of captopril in pharmaceutical formulations. The RuOHCF film was deposited on the surface of the electrode after applying 50 successive cycles and subsequent stabilization in a mixture of NaNO₃ 0.50 mol L^?1+HCl 0.050 mol L^?1 used as supporting electrolyte. The main processes responsible for the redox electrode response are attributed to the system Ru^II/Ru^III/Ru^IV, and appeared at ?0.080, 0.86 and 1.01 V (vs. SCE). The redox process at ?0.080 V was selected for the determination of captopril in the present study, once it provided higher sensibility and occurs in a lower potential than the other ones which can prevent interferences. The experimental parameters used in the determination of the analyte, using differential pulse voltammetry were optimized: pulse amplitude: 50 mV, scan rate: 5 mV s^?1 and potential window: ?0.5 to 0.2 V (vs. SCE). The analytical application of the sensor in real samples demonstrated a linear range between 0.060 and 0.80 µmol L^?1 (r=0.998) with a detection limit of 0.047 µmol L^?1. A mechanism based on co‐precipitation of captopril and the Ru (III) complex in the film is presented once the signal of the Ru^II/III redox couple decreases with increasing the analyte concentration. Recoveries of 99 to 100 % were achieved in pharmaceutical samples and the proposed procedure agreed with the HPLC official method within 95 % confidence level, according to the t‐Student test.     

银掺杂聚L-甲硫氨酸修饰电极同时测定对苯二酚和邻苯二酚

用循环伏安法制备了银掺杂聚L-甲硫氨酸修饰玻碳电极,研究了对苯二酚和邻苯二酚在该修饰电极上的电化学行为,建立了同时测定对苯二酚和邻苯二酚的新方法.研究发现,在pH=5.0的磷酸盐缓冲溶液中,扫速为100 mV/s时,对苯二酚和邻苯二酚在银掺杂聚L-甲硫氨酸修饰玻碳电极上均出现1对氧化还原峰,峰电位分别为:Epa=0.228 V、Epc =0.162 V和Epa=0.347 V、Epc =0.287 V,二者的氧化峰电位差达119 mV,还原峰差达125 mV.在最佳的条件下,用差分脉冲伏安法同时测定邻苯二酚和对苯二酚的线性范围为3.00 ×10-6～1.00 ×10-4mol/L,检出限为8.0×10-7 mol/L(对苯二酚)和5.0×10-7 mol/L(邻苯二酚).此法用于废水样中对苯二酚和邻苯二酚的测定,获得满意结果.     

对乙酰氨基酚在聚刚果红修饰电极上的伏安测定

应用循环伏安法于玻碳电极修饰聚刚果红薄膜,并研究对乙酰氨基酚(ACOP)在该修饰电极上的电化学行为.实验表明,聚刚果红修饰电极对ACOP具有良好的电催化性能.在2.0×10-7~2.0×10-6mol.L-1ACOP浓度范围内,其差示脉冲伏安峰电流随浓度变化呈良好的线性关系,检测限为4.0×10-8mol.L-1.该法可用于实际样品的含量测定.     

聚碱性品红修饰电极的制备及应用

研究了碱性品红在玻碳电极上聚合的最佳实验条件及其聚合机理，发现该修饰电极的多巴胺具有良好的催化作用，能大大提高多巴胺在的玻碳电极上的响应，在ｐＨ＝７．０的磷酸盐缓冲溶液中，用修饰电极测定巴胺的线性范围为２×１０＾－７～１×１０＾－５ｍｏｌ／Ｌ，检测限为１×１０＾－７ｍｏｌ／Ｌ，并且具有稳定性好，响应快，选择性等特点。     

聚L-甲硫氨酸修饰电极的制备及对尿酸的测定

在pH9.5的磷酸盐缓冲溶液中,利用循环伏安(CV)法制备了聚L-甲硫氨酸修饰玻碳电极(PLMet/GC/CME)。研究了尿酸(UA)在该电极上的电化学行为,建立了伏安法测定UA的新方法。在pH5.0的磷酸缓冲溶液中,扫描速率为200 mV/s,循环扫描电位在-0.3~1.0 V时,UA在PLMet/GC/CME上产生一个灵敏的氧化峰,峰电位位于0.52 V(vs.Ag/AgCl)。用CV法、线性扫描伏安(LSV)法和示差脉冲伏安(DPV)法对UA进行测定,测定的线性范围分别为2.50×10-6~1.00×10-4mol/L、5.00×10-6~1.00×10-4mol/L和8.00×10-7~1.00×10-4mol/L;检出限分别为8.0×10-7mol/L(CV、LSV法)和5.0×10-7mol/L(DPV法)。用LSV法对尿样中的UA进行测定,结果满意。