Preparation of PbS Nanoparticles by Phase-Transfer Method and Application to Pb2+-Selective Electrode Based on PVC Membrane

Abstract

A novel approach to prepare homogeneous PbS nanoparticles by phase-transfer method was developed. The preparatory conditions were studied in detail, and the nanoparticles were characterized by transmission electron microscopy (TEM) and UV-vis spectroscopy. Then a novel lead ion-selective electrode of polyvinyl chloride (PVC) membrane based on these lead sulfide nanoparticles was prepared, and the optimum ratio of components in the membrane was determined. The results indicated that the sensor exhibited a wide concentration range of 1.0 × 10^?5 to 1.0 × 10^?2 mol·L^?1. The response time of the electrode was about 10 s, and the optimal pH in which the electrode could be used was from 3.0 to 7.0. Selectivity coefficients indicated that the electrode was selective to the primary ion over the interfering ion. The electrode can be used for at least 3 months without any divergence in potential. It was successfully applied to directly determine lead ions in solution and used as an indicator electrode in potentiometric titration of lead ions with EDTA.     

Studies with the Selectrode: Determination of Oxalate Ion Activity

Abstract

A solid state oxalate sensor is reported utilizing a commercial ion-selective electrode, the Selectrode^TM. Comparative measurements in aqueous solution of similar carboxylate ions and common inorganic anions, indicates appreciabl'e selectivity for oxalate. The Selectrode^TM was activated with a mixture of silver sulphide, lead sulphide, and lead oxalate.     

Zinc-Selective Membrane Electrode Based On 5, 6, 14, 15-Dibenzo-l, 4-Dioxa-8, 12-Diazacyclopentadecane-5, 14-Diene

ABSTRACT

A new PVC membrane for zinc ions based on DBDA15C4 as membrane carrier was prepared. The electrode shows a linear stable response over a wide concentration range (5.0 × 10^?5-1.0 × 10^?1 M) with a slope of 22 mV/decade and a limit of detection of 3.0 × 10^?5 M (2.0 μg/ml). It has a very short response time of less than 5 s and can be use for at least 11 months without any divergence in potential. The zinc ion-selective electrode exhibited very good selectivities with respect to alkali, alkaline earth and some transition and heavy metal ions and could be used in a pH range 1.5-7.0. It was successfully applied for the direct determination of zinc in a pharmaceutical sample and, as an indicator electrode, in potentiometric titration of Zn²⁺ ions.     

Determination of Pseudoephedrine Hydrochloride in Some Pharmaceutical Drugs by Potentiometric Membrane Sensor Based on Pseudoephedrine–Phosphotungstate Ion Pair

Abstract

An ion-selective electrode (ISE) was developed for the rapid determination of pseudoephedrine hydrochloride (PSEHCl) in pharmaceutical preparations. The electrode incorporates a PVC membrane with a pseudoephedrine–phosphotungstate ion pair complex. The influences of membrane composition, temperature, pH of the test solution, and the interfering ions on the electrode performance were investigated. The sensor exhibits a Nernstian response for pseudoephedrine hydrochloride ions over a relatively wide concentration range (1.0 × 10^?1 to 1.0 × 10^?5 mol L^?1) with a slope of 56.2 ± 0.5 mV per decade at 25°C. It can be used in the pH range 4.0–10.5. The isothermal temperature coefficient of this electrode amounted to 0.0009 V/°C. The membrane sensor was successfully applied to determination of PSEHCl in its tablets and syrup.     

New Copper(II) Ion-Selective Membrane Electrode Based on Erythromycin Ethyl Succinate as a Neutral Ionophore

Abstract

The potentiometric response characteristics of a new copper(II) ion-selective PVC membrane electrode based on erythromycin ethyl succinate (EES) as ionophore were investigated. The electrode exhibited a Nernstian response to Cu²⁺ ions over the activity range of 1.5 × 10^?2 to 2.0 × 10^?6 mol L^?1 with a limit of detection of 6.3 × 10^?7 mol L^?1. Stable potentials were obtained in the pH range of 5.5–6.5. The potentiometric selectivity coefficients were calculated by using fixed interference method and revealed no important interferences except for Ag⁺. This electrode was successfully applied as an indicator electrode in determination of copper ions in real water samples.     

Calix[2]furano[2]pyrrole and related compounds as the neutral carrier in silver ion-selective electrode

The performance of calix[2]furano[2]pyrrole and related compounds used as neutral carriers for silver selective polymeric membrane electrode was investigated. The silver ion-selective electrode based on calix[2]furano[2]pyrroles gave a good Nernstian response of 57.1 mV per decade for silver ion in the activity range 1×10⁻⁶ to 1×10⁻² M. The present silver ion-selective electrode displayed very good selectivity for Ag⁺ ion against alkali and alkaline earth metal ions, NH₄⁺, and H⁺. In particular, the present Ag⁺-selective electrode exhibited very low responses towards Hg²⁺ and Pb²⁺ ions. The potentiometric selectivity coefficients of the silver ion-selective electrode exhibited a strong dependence on the solution pH. In particular, the response of the electrode to the Hg²⁺ activity was greatly diminished at pH 2.5 compared to that at pH 5.0. Overall, the performance of the present silver ion-selective electrode based on the ionophore, calix[2]furano[2]pyrrole, is very comparable to that of the electrode prepared with the commercially available neutral carrier in terms of slope, linear range, and detection limits.     

Response Amplification of an Ion-Selective Electrode

Abstract

The response of an ion-selective electrode can be amplified by connecting the cell, which is composed of an ion-selective electrode and a reference electrode, in series. For a cell using 1, 2 or 3 valinomycin electrodes connected in series, the response slopes to 1 × 10^?5 ?1 × 10^?1 M K⁺ were 58, 116 and 174 mV/activity decade (a.d.) at 25°C, respectively. This amplification method would especially be useful for accurate determinations with electrodes in the range of low concentrations outside the Nernstian response or for determinations of polyvalent ions, in which both cases exhibit small emf response changes in changing the ion concentration.     

Lead-Selective Membrane Potentiometric Sensor Based on a Recently Synthesized Bis(Anthraquinone) Sulfide Derivative

Abstract

A new PVC membrane electrode for lead ions, based on bis[(1-hydroxy-9,10-anthraquinone)-2-methyl]sulfide as membrane carrier, was prepared. The sensor exhibits a Nernstian response for Pb²⁺ over a wide concentration range (5.6 × 10^?3-4.0 × 10^?6 M). It has a response time of about 30 s and can be used for at least 3 months without any divergence in potentials. The proposed membrane sensor revealed good selectivities for Pb²⁺ over a wide variety of other metal ions. It was used as an indicator electrode in potentiometric titration of lead ion.     

Lead(II)-Selective Membrane Electrode Based on Tetraphenylporphyrin

ABSTRACT

A PVC membrane electrode for Pb² ions based on tetraphenylporphyrin was prepared. The sensor exhibits a Nernstian response for lead ions over a wide concentration range (1.0 x 10^?5-1.0 x 10^?2 M). The limit of detection is 8.5 x 10^?6M. It has a response time of 15 s and can be used for at least three months without any divergence in potential. The proposed electrode shows a fairly good discriminating ability towards Pb² ion in comparison to some alkali, alkaline earth, transition and heavy metal ions. The electrode can be used in the pH range 5.0 to 7.5. It was used as an indicator electrode in potentiometric titration of lead ion.     

Solid-contact pH-selective electrode using multi-walled carbon nanotubes

Multi-walled carbon nanotubes (MWCNT) are shown to be efficient transducers of the ionic-to-electronic current. This enables the development of a new solid-contact pH-selective electrode that is based on the deposition of a 35-μm thick layer of MWCNT between the acrylic ion-selective membrane and the glassy carbon rod used as the electrical conductor. The ion-selective membrane was prepared by incorporating tridodecylamine as the ionophore, potassium tetrakis[3,5-bis(trifluoromethyl)phenyl]borate as the lipophilic additive in a polymerized methylmethacrylate and an n-butyl acrylate matrix. The potentiometric response shows Nernstian behaviour and a linear dynamic range between 2.89 and 9.90 pH values. The response time for this electrode was less than 10 s throughout the whole working range. The electrode shows a high selectivity towards interfering ions. Electrochemical impedance spectroscopy and chronopotentiometry techniques were used to characterise the electrochemical behaviour and the stability of the carbon-nanotube-based ion-selective electrodes.     

Determination of Inorganic and Organic Thiophosphates with Ion-Selective Membrane Electrodes

Abstract

The conditions for the determination of sodium thiophosphate and sodium S-(2-amino-ethyl)-thiophos-phate in the presence of phosphate ion using ion-selective membrane electrodes are described. Both thiophosphates (inorganic and organic) are hydrolyzed in acidic medium. The phosphate ion is determined with Pb(II) using a Pb²⁺ – selective membrane electrode.

Cysteamine is determined by potentiometric titration with Hg(I1) using a Ag⁺/S^2? – crystal membrane electrode or by direct potentiometry with a Cu²⁺ selective membrane electrode. The results were verified by the iodination method.     

Element profiles in galvanostatically polarized K+-selective all-solid-state sensors with poly(vinyl chloride)-based membranes

The influence of galvanostatic polarization on ion concentration profiles in all-solid-state ion-selective sensors was studied. As a model system K⁺-selective electrode with poly(vinyl chloride)-based membrane, ionophore–valinomycin and polypyrrole doped by chloride ions as ion-to-electron transducer was selected. The ion exchanger—a typical component of ion-selective membrane—was replaced by lipophilic salt: tetradodecylammonium tetrakis(4-chlorophenyl) borate to avoid spontaneous extraction of potassium ions. Potassium, sodium, and chlorine distribution within the sensor phases were studied using laser ablation micro-sampling followed by inductively coupled plasma mass spectrometry measurements. The experiments revealed accumulation of potassium ions in course of cathodic galvanostatic polarization, with concentration decreasing by moving inside the ion-selective membrane. The surface content of K⁺ ions was found to be linearly dependent on applied current. Influence of sequential anodic galvanostatic polarization or open circuit conditioning applied after cathodic polarization revealed only limited recovery of the initial concentration profiles in the membrane.     

Determination of Fluoride Ions in Mouthwash Samples by a PVC Membrane Samarium(III) Sensor

Abstract

In this study, a new ion-selective electrode for Sm³⁺ is described, illustrating 2-[(E)-1-(1H-pyrrol-2-yl)methylidene]-1-hydrazinecarbothioamide (PMH) in a poly(vinylchloride) (PVC) membrane with nitrobenzene (NB) as a plasticizer and sodium tetraphenyl borate (NaTPB) as an anionic additive. The proposed sensor exhibited a Nernstian response for Sm³⁺ ions over a wide concentration range between 1.0 × 10^?2 and 1 × 10^?6 M, with a detection limit of 5.2 × 10^?7 M in the pH range of 4.2–8.5. Moreover, the sensor displayed the Nernstian slope of 19.8 ± 0.3 mV per decade, having a fast response time within 10 s over the entire concentration range. This electrode presented very good selectivity and sensitivity toward the Sm³⁺ ions over a wide variety of cations, including alkali, alkaline earth, transition-metal, and heavy-metal ions. It was used as an indicator electrode in the potentiometric titration of Sm³⁺ ions with EDTA. The membrane sensor was also applied to the determination of fluoride ions in mouthwash samples.     

A mercury(II) ion-selective electrode based on neutral salicylaldehyde thiosemicarbazone

A new ion-selective PVC membrane electrode based on salicylaldehyde thiosemicarbazone as an ionophore is developed successfully as sensor for mercury(II) ions. The electrode shows excellent potentiometric response characteristics and displays a linear log[Hg²⁺] versus EMF response over a wide concentration range of 1.778×10⁻⁶-1.0×10⁻¹ M with Nernstian slope of 29 mV per decade with the detection limit of 1.0×10⁻⁶ M. The response time of the electrode is less than 30 s and the membrane electrode operates well in the pH range of 1.0-3.0. The lifetime of the sensor is about 2 months. The electrode shows better selectivity towards Hg²⁺ ions in comparison with the alkali, alkaline and some heavy metal ions; most of these metal ions do not show significant interference (K^Pot_Hg,M values of the order of 10⁻³-10⁻⁴). The present sensor showed comparable or even better performance vis-à-vis similar PVC based ion-selective electrodes reported in literature. The sensor was also applied as an indicator electrode for potentiometric titration of Hg²⁺ions with I⁻ and Cr₂O₇²⁻.     

The Potential Response Of Copper(Ii) Sulfide Ion Selective Electrode To Hg(Ii) Ions In Aqueous Solution

Abstract

The application of a cupric ion-selective electrode with a membrane of mixed Ag₂S-CuS to measure the activity of Hg(II) is presented. The linear electrode response curve which covers near three decades, from 10^?5 to 10^?2 mol dm^?3, of mercuric concentration range was obtained, under background of acetate buffer.     

Perchlorate Ion-Selective Electrodes with the Liquid Membranes of the O-Phenanthroline Chelate or its Related Compounds

Abstract

The metal chelates of o-phenanthroline, a, a′-dipyridyl or bathophenanthroline were used as the ion exchanger in the liquid membrane of the perchlorate ion-selective electrode. The electrode with a nitrobenzene membrane containing tris(bathophenanthroline)ferrous perchlorate is the highest sensitive one and gives a linear Nernstian response up to about 1 × 10 ^?5 M perchlorate. The membrane electrode having the ferrous ion-chelate of o-phenanthroline as an ion exchanger shows an excellent selectivity for perchlorate ion over nitrate or iodide Ion. The effects of the chelate concentration in the membrane and the central metal species of the chelate are examined on the electrode performance.     

A PVC-based 1,8-diaminonaphthalen electrode for selective determination of vanadyl ion

A PVC membrane vanadyl (VO²⁺) ion-selective electrode was constructed using 1,8-diaminonaphthalen (DAN) as a neutral carrier. The electrode shows good Nernstian response for VO²⁺ ions over a wide concentration range (1.0×10⁻¹-1.0×10⁻⁵ M). The optimum composition of the membrane was 55 wt.% poly(vinylchloride), 35 wt.% 2-nitrophenyl octyl ether (NPOE), 5 wt.% ionophore, and 5 wt.% potassium tetrakis(p-chlorophenyl)borate (KTpClPB). It has relatively fast response time and can be used at least for 5 weeks without any considerable divergence in potentials. The proposed electrode revealed relatively good selectivity for VO²⁺ over wide variety of other metal ions. The electrode was used for the potentiometric titration of VO²⁺ ions with EDTA.     

Determination of betamethasone sodium phosphate in pharmaceuticals by potentiometric membrane sensor based on its lidocaine ion pair

Betamethasone sodium phosphate (BMNaP) has been employed as an electroactive material in the design of an ion-selective electrode (ISE). The electrode incorporates PVC membrane with betamethasone sodium phosphate-lidocaine ion pair complex. The influences of membrane composition, temperature, pH of the test solution, and the interfering ions on the electrode performance were investigated. The sensor exhibits a Nernstian response for betamethasone sodium phosphate ions over a relatively wide concentration range (1.0 × 10^?1 to 1.0 × 10^?5 M) with a slope of 28.4 ± 0.9 mV per decade at 25°C. It can be used in the pH range 4.0–10.0. The isothermal temperature coefficient of this electrode amounted to ?0.0008 V/°C. The membrane sensor was successfully applied to the determination of betamethasone sodium phosphate in pharmaceutical products.     

Coated,Wire-Based,New Schiff Base Potentiometric Sensor for Lead(II) Ion

An ion-selective electrode for lead(II) based on a dispersion of N,N"-bis(3-methyl salicylidine)-p-phenyl methane diamine particles into a polymeric membrane using coated-wire configuration is described. Membranes based on polyvinyl chloride containing different amounts of plasticizer and ionophore are studied. The best performance in terms of slope (30.3 ± 0.6 mV per decade) and response time (<15 s) is displayed. The sensor shows a Nernstian response for Pb(II) ions over a wide concentration range of 2.0 × 10^–5 to 0.10 M. The sensors can be used for more than three months without any considerable divergence in potentials. The selectivity is also good towards the most common univalent and divalent cations and the signal is constant in the pH range 1.6–6.0. An application to lead determination in mineral rocks and wastewater proved to be a success, and it was employed as an indicator electrode in potentiometric titration of CrO^2– ₄ with lead ions.     

The determination of free long-chain quaternary ammonium species with an ion-selective electrode based on a cetyltrimethylammonium ion pair

The cetyitrimethylammonium ion-selective electrode described is based on a tetrazole ion-pair and silicone-rubber membranes. The electrode is almost Nernstian in response from 10^-6 M to the critical micelle concentration. The electrode responds little to dodecyland decyltrimethylammonium ions and inorganic ions. Selectivity coefficients for numerous compounds are given. The uses of the ion-selective electrode are discussed in terms of the ability to monitor free quaternary ammonium ions in the presence of electrolyte and complexing additives. The electrode described can be useful in developing certain pharmaceutical formulations.