Sol—Gel Derived Carbon Ceramic Electrode Bulk—Modified with Tris（1,10—phenanthroline—5,6—dione） iron （Ⅱ）Hexafluorophosphate and Its Use as an Amperometric Iodate Sensor

A surface‐renewable tris(1, 10‐phenanthroline‐5, 6‐dione) iron (D) hexafluorophosphate (FePD) modified carbon ceramic electrode was constructed by dispersing FePD and graphite powder in methyltrimethoxysilane (MTMOS) based gels. The FePD‐modified electrode presented pH‐dependent voltammetric behavior, and its peak currents were diffusion‐controlled in 0.1 mol/L Na₂SO₄ + H₂SO₄ solution (pH = 0.4). In the presence of iodate, dear electrocatalytic reduction waves were observed and thus the chemically modified electrode was used as an amperometric sensor for iodate in common salt. The linear range, sensitivity, detection limit and response time of the iodate sensor were 5 × 10^?6–1 × 10^?2 mol/L, 7.448 μA·L/ mmol, 1.2 × 10^?6 mol/L and 5 s, respectively. A distinct advantage of this sensor is its good reproducibility of surface‐renewal by simple mechanical polishing.     

Electrode Based on Nickel‐containing SBA‐15 for the Determination of Copper in Ethanol Biofuel

A sensor based in a graphite–polyurethane composite electrode modified with the mesoporous nanostructured silica with hexagonal array of pores called Santa Barbara Amorphous type material (SBA‐15) containing nickel was built. The presence of Ni, incorporated during the synthesis of SBA‐15, resulted in an increase in sensitivity when compared to the other electrodes based on the unmodified SBA‐15. A procedure was proposed for the determination of Cu²⁺ in ethanol biofuel by square wave stripping voltammetry with linear response in concentration levels of 1.0×10^?8 and 1.0×10^?7 mol L^?1, resulting in a limit of detection of 1.83×10^?10 mol L^?1 and precision (RSD) of 2.09 %.     

Rate constants for hydrogen abstraction reactions of the sulfate radical,SO4−. Alcohols

Rate constants have been determined for the reactions of SO₄^? with a series of alcohols, including hydrated formaldehyde. The SO₄^? radical was produced by the laser-flash photolysis of persulfate, S₂O₈^2?. Rate constants for the reactions of SO₄^? with alcohols range from 1.0 × 10⁷ for methanol to 3.4 × 10⁸ M^?1 s^?1 for 1-octanol. Rate constants for the reactions of SO₄^? with deuterated methanol and ethanol are lower by about a factor of 2.5. For methanol, ethanol, and 2-propanol, the temperature dependence of the rate constant was determined over the range 10–45°C.     

Differential Pulse Voltammetric Determination of Sildenafil Citrate (Viagra®) in Pharmaceutical Formulations Using a Boron-Doped Diamond Electrode

The determination of sildenafil citrate using differential pulse voltammetry and a cathodically pre-treated boron-doped diamond electrode is described. The obtained analytical curve is linear in the sildenafil concentration range 7.3 × 10^?7 ? 7.3 × 10^?6 mol L^?1 in a 0.1 mol L^?1 H₂SO₄, with a detection limit of 6.4 × 10^?7 mol L^?1. The proposed method, which is fast and simple to carry out, was successfully applied in the determination of sildenafil citrate in Viagra® pharmaceutical formulations, with results in close agreement (at 95% confidence level) with those obtained using a comparative HPLC method.     

Study and Application of Polarographic Catalytic Wave of Chlordiazepoxide in the Presence of Persulfate

ＩｎｔｒｏｄｕｃｔｉｏｎＣｈｌｏｒｄｉａｚｅｐｏｘｉｄｅ (7 ｃｈｌｏｒｏ 2 ｍｅｔｈｙｌａｍｉｎｏ 5 ｐｈｅｎｙｌ 3Ｈ 1,4 ｂｅｎｚｏｄｉａｚｅｐｉｎｅ 4 ｏｘｉｄｅ)ｓｈｏｗｉｎｇｐｏｗｅｒｆｕｌａｎ ｔｉａｎｘｉｅｔｙｅｆｆｅｃｔｈａｓｂｅｅｎｗｉｄｅｌｙｕｓｅｄａｓａｐｓｙｃｈｏｔｈｅｒａｐｅｕ ｔｉｃｄｒｕｇ .Ｃｏｎｓｅｑｕｅｎｔｌｙ ,ｔｈｅｎｅｅｄａｒｏｓｅｆｏｒｓｅｎｓｉｔｉｖｅａｎｄｒａｐｉｄｄｅｔｅｒｍｉｎａｔｉｏｎｏｆｃｈｌｏｒｄｉａｚｅｐｏｘｉｄｅｉｎｂｌｏｏｄ ,ｕｒｉｎｅａｎ…     

Reactivity of selected volatile organic compounds (VOCs) toward the sulfate radical (SO4−)

Rate constants for a series of alcohols, ethers, and esters toward the sulfate radical (SO₄^?) have been directly determined using a laser photolysis set‐up in which the radical was produced by the photodissociation of peroxodisulfate anions. The sulfate radical concentration was monitored by following its optical absorption by means of time resolved spectroscopy techniques. At room temperature the following rate constants were derived: methanol ((1.6 ± 0.2) × 10⁷ M^?1 s^?1); ethanol ((7.8 ± 1.2) × 10⁷ M^?1 s^?1); tert‐butanol ((8.9 ± 0.3) × 10⁵ M^?1 s^?1); diethyl ether ((1.8 ± 0.1) × 10⁸ M^?1 s^?1); MTBE ((3.13 ± 0.02) × 10⁷ M^?1 s^?1); tetrahydrofuran (THF) ((2.3 ± 0.2) × 10⁸ M^?1 s^?1); hydrated formaldehyde ((1.4 ± 0.2) × 10⁷ M^?1 s^?1); hydrated glyoxal ((2.4 ± 0.2) × 10⁷ M^?1 s^?1); dimethyl malonate (CH₃OC(O)CH₂C(O)OCH₃) ((1.28 ± 0.02) × 10⁶ M^?1 s^?1); and dimethyl succinate (CH₃OC(O)CH₂CH₂C(O)OCH₃) ((1.37 ± 0.08) × 10⁶ M^?1 s^?1) where the errors represent 2σ. For the two latter species, we also measured the temperature dependence of the corresponding rate constants. A correlation of these kinetics with the bond dissociation energy is also presented and discussed. © 2001 John Wiley & Sons, Inc. Int J Chem Kinet 33: 539–547, 2001     

Polarographic Behavior of Gemfibrozil in the Presence of Dissolved Oxygen and Its Analytical Application

The polarographic behavior of gemfibrozil is investigated in 0.2 mol L^?1 KH₂PO₄‐Na₂HPO₄ (pH 5.8±0.1)‐8% ethanol supporting electrolyte in the absence and the presence of dissolved oxygen. The results demonstrate that the polarographic reduction peak at ca. ?1.17 V is a catalytic hydrogen wave after deaeration, and the enhanced reduction peak in the presence of dissolved oxygen is the so‐called parallel catalytic hydrogen wave. Based on the parallel catalytic hydrogen wave, a novel method has been developed for the determination of gemfibrozil by single sweep polarography. Calibration plot is linear in the range of 1.8×10^?7–2.4×10^?6 mol L^?1 and detection limit is 9.0×10^?8 mol L^?1. The proposed method is applied to the direct determination of the gemfibrozil in pharmaceutical preparations. The proposed method is simpler, faster and more sensitive than the known methods for gemfibrozil analyses.     

High Selective Determination of Anionic Surfactant Using Its Parallel Catalytic Hydrogen Wave

IntroductionAnionicsurfactants (AS)arewidelyusedinhouse holdorindustrialcleaners ,cosmetics ,researchlaborato ries,textiles ,pharmacies ,etc .,solargeamountofASreleasedintotheenvironmentarecausingpollution .There foreitisnecessarytodevelopafast,simpleandcosteffec tivemethodforthedeterminationofAS .Theofficialmeth odsrecommendedforthedeterminationofASarespec trophotometryandpotentialtitration .SpectrophotometricmethodanditsvariationsarebasedonthemeasurementofthecoloredassociatesofASwithposi…     

Ozone reduction at Nafion modified Au electrode and the measurement of ozone concentration in highly resistive solutions

The mass transport and charge transfer kinetics of ozone reduction at Nafion coated Au electrodes were studied in 0.5 mol/L H2SO4 and highly resistive solutions such as distilled water and tap water. The diffusion coefficient and partition coefficient of ozone in Nafion coating are 1.78×10-6 cm2·s-1 and 2.75 at 25℃ (based on dry state thickness), respectively. The heterogeneous rate constants and Tafel slopes for ozone reduction at bare Au are 4.1×10-6 cm·s-1, 1.0×10-6 cm·s-1 and 181 mV, 207 mV in 0.5 mol/L H2SO4 and distilled water respectively and the corresponding values for Nafion coated Au are 5.5×10-6 cm·s-1, 1.1×10-6 cm·s-1 and 182 mV, 168 mV respectively. The Au microelectrode with 3 μm Nafion coating shows good linearity over the range 0-10 mmol/L ozone in distilled water with sensitivity 61 μA·ppm-1 ·cm-2, detection limit 10 ppb and 95% response time below 5 s at 25℃. The temperature coefficient in range of 11-30℃ is 1.3%.     

Electrochemical investigation and determination of ceftazidime in pharmaceutical dosage forms and human urine

A voltammetric study of the oxidation of Ceftazidime (CEFT) has been carried out at the glassy carbon electrode by cyclic, differential pulse (DPV) and square wave (SWV) voltammetry. The oxidation of CEFT was irreversible and exhibited diffusion controlled process depending on pH. The oxidation mechanism was proposed and discussed. According to the linear relationship between the peak current and concentration, DPV and SWV voltammetric methods for CEFT assay in pharmaceutical dosage forms and human urine were developed. For analytical purposes, a well resolved diffusion controlled voltammetric peak was obtained in 0.1 M H₂SO₄ at 1.00 and 1.02 V for differential pulse and square wave voltammetric techniques, respectively. The linear response was obtained within the range of 4 × 10^?6?8 × 10^?5 M with a detection limit of 6 × 10^?7 M for differential pulse and 4 × 10^?6–2 × 10^?4 M with a detection limit of 1 × 10^?6 M for square wave voltammetric technique. The determination of CEFT in 0.1 M H₂SO₄ was possible over the 2 × 10^?6–1 × 10^?4 M range in urine sample for both techniques. The standard addition method was used for the recovery studies.     

Anodic Stripping Voltammetric Determination of Mercury(II) in Water Using a 4‐Tert‐Butyl‐1‐(Ethoxycarbonylmethoxy)Thiacalix[4]Arene Modified Glassy Carbon Electrode

A glassy carbon electrode coated the film of 4‐tert‐butyl‐1‐(ethoxycarbonylmethoxy)thiacalix[4]arene is designed for the determination of trace amounts of Hg²⁺. Compared with bare glassy carbon electrode, the modified electrode can improve the measuring sensitivity of Hg²⁺. Under the optimum experimental condition, the modified electrode in 0.1 mol L^?1 H₂SO₄ + 0.01 mol L^?1 KCl solution shows a linear voltammetric response in the range of 8.0 × 10^?9 ～ 3.0 × 10^?6 mol L^?1 with detection limit 5.0 × 10^?9 mol L^?1 for Hg²⁺. The high sensitivity, selectivity, and stability of modified electrode also prove its practical application for a simple, rapid and economical determination of Hg²⁺ in water samples.     

Electrochemical Behavior of 6-Mercapto-Purine at Hanging Copper Amalgam Dropping Electrode and Its Trace Determination by Differential Pulse Adsorption Cathodic Stripping Voltammetry

Abstract

The electrochemical behavior of 6-MP was studied by cyclic voltammetry at a hanging copper amalgam dropping electrode (HCADE). It was found that 6-MP could form a complex with the Cu(II) stripped from the HCADE, showing a new peak at ?0.19V in the medium of 0.1mol/L LiClO₄-0.5mol/L HClO₄ solution. The mechanism of the reaction was proposed. This new peak was sensitive and could be used for the determination of trace 6-MP by differential pulse adsorption cathodic stripping voltammetry (DPAdCSV). The linear range was from 3.6×10^?10 to 5.3×10^?6 mol/L, and the detection limit was about 1.2×10^?10 mol/L (S/N=3). The method was also successfully applied to the determination of 6-MP in pharmaceutical tablets.     

Reactivity of the 5-hexenyl radical toward the anion of 2-nitropropane and borohydride anion

The 5-hexenyl radical adds to the anion of 2-nitropropane with a rate constant of ≈ × 10⁶ L/mol-s at 40°. Hydrogen atom abstraction from BH₄^? occurs more slowly than abstraction from CH₃O^? and with a rate constant less than 1 × 10⁴ L/mol-s at 30°. The reaction of Δ⁵- hexenylmercury chloride with sodium borohydride in MeOH/NaOH proceeds via hydrogen abstraction by the hexenyl radical from RHgH and not from NaBH₄.     

Kinetics of the reaction of the sulfate radical with the oxalate anion

The kinetics of the reaction of the sulfate radical, SO₄⁻, with the oxalate anion C₂O₄²⁻ was studied in aqueous solution and second-order rate constants, corrected for the effects of ionic strength, derived. Measurements were carried out over the temperature range 24–60°C resulting in the expression k₀ = 2.10 ± 0.96 × 10⁸ exp(−1080 ± 140/T) L mol⁻¹ s⁻¹. © 1996 John Wiley & Sons, Inc.     

Simultaneous Determination of Iron and Copper in Ethanol Fuel Using Nafion/Carbon Nanotubes Electrode

This work presents the analytical method development for iron and copper determination in ethanol fuel. This method was developed using stripping voltammetry with a glassy carbon electrode modified with Nafion/Carbon‐nanotubes. With linear sweep stripping voltammetry was achieved a limit of detection of 7.1×10^?7 mol L^?1 for Fe³⁺ and 5.1×10^?8 mol L^?1 for Cu²⁺. The amperometric sensitivities were 2.0×10⁶ µA mol^?1 L for Fe³⁺ and 2.8×10⁷ µA mol^?1 L for Cu²⁺. The recovery study showed that the method has good accuracy and repeatability, with recovery of 108 and 103 % for Fe³⁺ and Cu²⁺ respectively.     

Determination of Methimazole and Carbimazole Using Polarography and Voltammetry

Abstract

Anodic waves of methimazole (I) (1-methylimidazole-2-thiol) and carbimazole (II) (1-ethoxycarbonyl-3-methyl-2-thio-4-imidazoline) on mercury electrodes correspond to mercury salt formation. Both compounds form in the thiono form a soluble complex at pH < 6, compound (I) at higher pH-values a slightly soluble salt of the thiol form. Electrode processes involving the thiol form are complicated by adsorption. Oxidation at solid electrodes occurs only at potentials more than 0.5 V more positive. For compound (I) spectrophotometry indicated pK_a=12.0 ± 0.2. By d.c. polarography in 0.1 M H₂SO₄ containing 10% ethanol the determination of both compounds is possible between 4 × 10^? and 1 × 10^?3 M, by differential pulse polarography between 1 × 10^? and 1 × 10^?4 M, by differential pulse voltammetry at HMDE between 5 × l0^?7 and 6 × 10^? M.     

An Ethanol Biosensor Based on Simple Immobilization of Alcohol Dehydrogenase on Fe3O4@Au Nanoparticles

An ethanol biosensor based on alcohol dehydrogenase (ADH) attached to Au seeds decorated on magnetic nanoparticles (Fe₃O₄@Au NPs) is presented. ADH was immobilized on Fe₃O₄@Au NPs, which were subsequently fixed by a magnet on a carbon paste electrode modified with 5 % (m : m) MnO₂. Optimum conditions for the amperometric determination of ethanol with the biosensor were as follows: working potential +0.1 V (vs. Ag/AgCl); supporting electrolyte: 0.1 M phosphate buffer solution at pH 6.8 containing 0.25 mM of the coenzyme (NAD⁺); working electrode: carbon paste with magnetically attached Fe₃O₄@Au NPs (0.012 mg ? cm^?2 electrode area) with immobilized alcohol dehydrogenase (120 units per cm² of electrode area). Linearity between signal and concentration was found for the range from 0.1 to 2.0 M ethanol (r²=0.995) with a detection limit of 0.07 M, a sensitivity of 0.02 µA ? mM^?1 ? cm^?2, a reproducibility of 4.0 % RSD, and a repeatability of 2.7 % RSD. The results for the determination of ethanol in alcoholic beverages showed good agreement with gas chromatography (GC) with recovery of 96.0 – 108.8 %.     

Stability Improvement of Prussian Blue by a Protective Cellulose Acetate Membrane for Hydrogen Peroxide Sensing in Neutral Media

The cellulose acetate covered Prussian blue modified glassy carbon electrode (GCE/PB/CA) was fabricated as a novel hydrogen peroxide sensor. It was shown by scanning electron microscope (SEM) and atomic force microscope (AFM) that Prussian blue was covered and protected by cellulose acetate perfectly. The modified electrode showed a good electrocatalytic activity for H₂O₂ reduction in neutral aqueous solution. H₂O₂ was detected amperometrically in 0.05 mol/L phosphate buffer solutions (pH 7.0, containing 0.1 mol/L KCl as supporting electrolyte) at an applied potential of ?0.2 V (vs. SCE). The response current was proportional to the concentration of H₂O₂ in the range of 1.0×10^?5 mol/L to 2.5×10^?4 mol/L with the detection limit of 2.2×10^?6 mol/L at a signal to noise ratio 3.     

Electrochemical reduction and quantification of menadione in sodium dodecyl sulfate micellar media

Menadione cyclic voltammograms show a pair of redox steps on glassy carbon electrode in 0.1 M H₃PO₄ with potential separation of 343 mV. Cationic, nonionic, and anionic surfactants micellar media significantly decrease the menadione peak potential separation. Statistically significant increase of menadione reduction current (3- and 4.4-fold) has been observed in Triton X 100 and sodium dodecyl sulfate (SDS) micellar media, respectively. Electrochemical reduction of menadione in 9 mM SDS micellar media is reversible diffusion-controlled one-electron process corresponding to formation of relatively stable semiquinone anion radical. The linear dynamic ranges of menadione determination are 7–560 and 600–2,550 μM with the limits of detection and quantification of 1.66 and 5.53 μM, respectively. The current concentration sensitivity is (8.6?±?0.2)?×?10³ μA μM^?1. The voltammetric method for the determination of menadione in pharmaceutical “Aekol” based on preliminary extraction with ethanol has been developed.     

Aqueous Polymerization of Methyl Methacrylate Initiated by Pyridine-Sulfur Dioxide Complex

The aqueous polymerization of MMA was studied kinetically at 40° C using low concentrations of Py-SO₂ complex as initiator. For [Py-SO₂] < 2 × 10^?2 mol/L, R_p ∞ [PY-SO₂]^0.5 [M]^1.5, and for [Py-SO₂] > 2 × 10^?2 mol/L, R_p ∞ [Py-SO₂]^0,0[M]^1.08. Polymerization is considered to proceed by a radical mechanism. The radical generation or the initiation step is believed to proceed through equilibrium complexation between the Py-SO₂ complex and monomer molecules. For [Py-SO₂] < 2 × 10^?2 mol/L, the polymerization is characterized by bimolecular termination. Above this [Py-SO₂], chain termination by a degradative initiator transfer process assumes prominence.