Separation-Free Electrochemical Immunosensor Strategies

ABSTRACT

The simplification of the assay strategy is an essential development for the commercial success of immunosensors. The problems associated with assay simplification stem from the fact that immune recognition is not accompanied by an easily detectable event. Direct methods such as those based on optical systems have circumvented such problems by measuring mass changes. However, such devices are not so amenable to instrumental simplification. Electrochemical methods have so far offered the best prospects for commercial biosensors. Success has only occurred with enzyme-based biosensors measuring simple biochemical molecules such as glucose, lactate and creatinine. The use of antibody-based assay strategies requires the introduction of electrochemical labels. Introduction of such species results in greater complexity, accompanied by a series of assay steps. This extension in assay complexity is in direct opposition to the concept of the biosensor: simplicity. Several strategies have been taken to remove these assay steps and reduce the complexity of the immunoassay. Such strategies may contribute to the application of immunosensors as a serious commercial proposition.     

Piezoelectric Quartz Crystal Anti‐Protein Immunosensors Based on Immobilized Fullerene C60‐Proteins

Various fullerene C60‐proteins such as C60‐myoglobin (C60‐Mb), C60‐hemoglobin (C60‐Hb) and C60‐gliadin, coated piezoelectric quartz crystals were prepared and applied in piezoelectric quartz crystal immunosensors for protein‐antibodies such as anti‐myoglobin (Anti‐Mb), anti‐hemoglobin (Anti‐Hb) and anti‐gliadin respectively. The immobilizations of myoglobin, hemoglobin and gliadin onto Fullerene C60 were studied with a C60‐coated piezoelectric crystal detection system, respectively. The partially irreversible frequency responses for theses proteins were observed by a desorption study, implying that C60 can strongly adsorb these proteins. Thus, immobilized C60‐Mb, C60‐Hb and C60‐gliadin coating materials were successfully prepared and identified with FTIR spectrometry. The C60‐Mb, C60‐Hb and C60‐gliadin coated piezoelectric (PZ) quartz crystal immunosensors with homemade computer interfaces for signal acquisition and data processing were developed and applied for detection of Anti‐Mb, Anti‐Hb and anti‐gliadin respectively. The C60‐protein coated PZ immunosensors for Anti‐Mb, Anti‐Hb and antigliadin exhibited linear frequency responses to the concentrations of theses anti‐proteins with sensitivities of 1.43 × 10³, 2.59 × 10³ and 8.05 × 10³ Hz/(mg/mL) respectively. The detection limits of these PZ‐immunosensors were 4.36 × 10^?3, 3.23 × 10^?3 and 1.98 × 10^?3 mg/mL for Anti‐Mb, Anti‐Hb and anti‐gliadin respectively. Effects of pH and temperature on the frequency responses of the anti‐protein PZ‐immunosensors were also investigated. The optimum pH of these anti‐proteins and the optimum temperature for the PZ‐immunosensors were observed at pH = 7 and around 30 °C respectively. The interferences of various common species in human blood, e.g., cysteine, tyrosine, urea, glucose, ascorbic acid and metal ions, to these anti‐protein PZ‐immunosensors were also investigated respectively. These species showed nearly no interference or quite small interference with the anti‐protein PZ‐immunosensors. The reproducibility and lifetime of these immobilized C60‐protein coated PZ crystal immunosensors were also investigated and discussed.     

Label-free microcantilever-based immunosensors for highly sensitive determination of avian influenza virus H9

We report on label-free immunosensors for the highly sensitive detection of avian influenza virus. The method makes use of the microcantilevers of an atomic force microscope onto which monoclonal antibodies against avian influenza virus were covalently immobilized. The factors influencing the performance of the resulting immunosensors were optimized by measuring the deflections of the cantilever via optical reflection, and this resulted in low detection limits and a wide analytical range. The differential deflection signals revealed specific antigen binding and their intensity is proportional to the logarithm of the concentrations of the virus in solution. Under optimal conditions, the immunosensors exhibit a linear response in the 7.6 ng mL^?1 to 76 μg mL^?1 concentration range of avian influenza virus, and the detection limit is 1.9 ng mL^?1.

Detection of Aflatoxins in Capsicum Spice Using an Electrochemical Immunosensor

Abstract

Electrochemical immunosensor based on immobilized aflatoxin B1 (AFB)–albumin conjugate and polyclonal antibody against AFB1 was performed for a competitive assay of AFB1 in capsicum spice. Spiked samples were used for construction of calibration curve. The proved limit of detection was 2.4 ppb. Immunosensor long-term stability was also estimated. Decrease of immunosensor sensitivity was less than 10% when stored in a refrigerator and approximately 22% for the immunosensor preserved at laboratory temperature for two weeks. Consequent performance of immunosensors for assay of real capsicum spice samples with proven aflatoxins presence produced good correlation with the data from valid method (high-performance liquid chromatography with fluorescence detector).     

Piezoelectric Immunosensors for Environmental Monitoring

This article is a tutorial review of piezoelectric immunosensors and their application to environmental monitoring.

The basic theory and historical developments of piezoelectricity are introduced. The development of piezoelectric sensors and eventually immunosensors for the specific detection of analytes of environmental importance are mentioned. The various assay formats and their advantages as well as examples of the different approaches taken by different analysers are also mentioned. Current developments within this laboratory on the development of piezoelectric immunosensors for the detection of okadaic acid and microcystin-LR are briefly introduced. The major drawbacks of piezoelectric immunosensors and their potential future are also discussed.     

Development of an impedimetric immunosensor based on electropolymerized polytyramine films for the direct detection of Salmonella typhimurium in pure cultures of type strains and inoculated real samples

The development of a faradic impedimetric immunosensor based on electropolymerized polytyramine (Ptyr) films for the detection of S. typhimurium in milk is described for the first time. Polyclonal anti-Salmonella was cross-linked, in the presence of glutaraldehyde vapors, on Ptyr-modified gold electrodes. The dielectric behaviour of Ptyr films was evaluated with capacitance measurements, while their stability in neutral aqueous solutions was examined with impedimetric measurements. The effect of the concentration of tyramine in the forming solution on both the sensitivity and the dynamic range of the resulted immunosensors was also investigated. The alteration of the interfacial features of the electrodes due to different modification or recognition steps, was measured by faradic electrochemical impedance spectroscopy in the presence of a hexacyanoferrate(II)/(III) redox couple. At samples containing a low initial concentration of 10 cfu mL⁻¹S. typhimurium, that actually defines the LOD of the immunosensors, signal changes of 33% and 88% were achieved after 3 and 10 h incubation, respectively. To achieve the working simplicity expected by a biosensor, immunoreaction was performed directly in cultures. This resulted in the elimination of various centrifugation and washing steps, which are used for the isolation of bacteria cells from the culture, thus making the proposed immunosensors promising candidates for on-site applications. Finally, the proposed immunosensors were successfully used for the detection of S. typhimurium in experimentally inoculated milk samples.     

Determination of Free L-T4 and Free L-T3 from Blood Using the Immunosensors/Sequential Injection Analysis System

An immunosensors/sequential injection analysis system is proposed for the assay of thyroid hormones free L-T₄ and free L-T₃ in blood samples. The working concentration ranges for free L-T₄ and free L-T₃, are between 2.0 and 720.0 pmol/L and between 2.0 and 340.0 pmol/L, respectively, with detection limits of 1.0 and 1.7 pmol/L, respectively. The selectivity of the immunosensors, as well as the recovery tests done for free L-T₄ and free L-T₃ (99.90 ± 0.01% (n = 10) and 99.94 ± 0.02% (n = 10)), made the immunosensors/sequential injection analysis system suitable for the direct assay of thyroid hormones in blood samples.     

Insulin Surface Acoustic Wave Immunosensor Based on Immobilized C60/Anti‐Insulin Antibody

Immobilized fullerene C₆₀/anti‐insulin antibody was prepared and applied in shear horizontal surface acoustic wave (SH‐SAW) immunosensors to detect insulin in aqueous solutions. The immobilizations of anti‐insulin onto fullerene were studied through a C₆₀/PVC coated SH‐SAW sensor system in liquid. The partially irreversible frequency response for an anti‐insulin antibody was observed by the desorption study, which implied that fullerene could chemically react with anti‐insulin. C₆₀/anti‐insulin coating materials were successfully prepared and identified with an FTIR spectrometer. The C₆₀/anti‐insulin coated SH‐SAW immunosensors were developed and applied for detection of insulin in aqueous solutions. Within the range of normal human insulin concentration, the SH‐SAW immunosensors immobilized with C₆₀/anti‐insulin exhibited linear frequency responses to the concentration of insulin with a sensitivity of 130 Hz/pM. The SH‐SAW immunosensor immobilized with C₆₀/anti‐insulin showed a detection limit of 0.58 pM for insulin in aqueous solution. The interference of various common bio‐species in human blood, e.g. urea, ascorbic acid, tyrosine, and metal ions, to the SH‐SAW immunosensor immobilized with C₆₀/anti‐insulin for insulin was investigated. These common bio‐species interferences showed nearly no interference to the SAW immunosensors coated with C₆₀/anti‐insulin. The reproducibility of the SH‐SAW immunosensor immobilized with C₆₀/anti‐insulin for insulin was also investigated and is discussed.     

New immunosensors for 2,4-D and 2,4,5-T pesticides determination

New immunosensors for 2-(2, 4-dichlorophenoxy) acetic acid (i.e. 2,4-D) and (2, 4, 5-trichlorophenoxy) acetic acid (i.e. 2,4,5-T) pesticide determination were developed using a non commercial antibody, hydrogen peroxide transducer and horseradish peroxidase as enzyme marker. The results show the full validity of these immunosensor devices, which were optimized using a ‘competition’ separation procedure. These immunosensors were also used to test pesticide recovery in common real matrices such as field grass, maize and wheat samples, for which good results were obtained. The immunosensors developed demonstrated a good selectivity versus different kinds of pesticides and may thus be considered as suitable devices for application to real matrices (LOD?=?8.0?×?10^?11?mol?L^?1; RSD%?=?5.2 for 2,4-D and LOD?=?2.8?×?10^?9?mol?L^?1; RSD%?=?6.1 for 2,4,5-T).     

Voltammetric Label‐free Immunosensors for the Diagnosis of Cystic Echinococcosis

Cystic echinococcosis (CE) or hydatid disease is a parasitic infection caused by Echinococcus granulosus. Early serodiagnosis and continuous monitoring of the disease is very important for medical treatment. Here, we report the detecting of both echinococcus antigen and antibody for the diagnosis of hydatid disease using square wave voltammetry (SWV)‐based immunosensors. The gold electrodes were functionalized using cysteamine/phenylene diisothiocyanate linkers and used for the immunosensors fabrication. The hydatid antigen and antibody immunosensors were constructed by the immobilization of either purified rabbit polyclonal antibody or recombinant antigen B (AgB), respectively on the functionalized gold electrodes surfaces. The detection in both cases was achieved by following the change in the SWV reduction peak current of the ferro/ferricyanide redox couple upon antibody or antigen binding. These immunosensors enabled the detection of echinococcus antigen and antibody within a concentration range of 1 pg.mL^?1 to 1 μg.mL^?1 with detection limits of 0.4 pg.mL^?1 and 0.3 pg.mL^?1, respectively. A preliminary application of the developed immunosensor was performed in spiked serum sample showing good recovery percentages ranging from 102 to 110 % for both hydatid antibody and antigen detection. This easy‐to‐use, sensitive, and low cost quantitative method holds great promise for the early diagnosis of hydatid disease and thus, better managements and treatment outcomes.     

Structure of the receptor layer in electrochemical immunosensors. Modern trends and prospects of development

Literature data on the modern state and prospects for the development of research in the area of receptor layer immobilization in electrochemical immunosensors were examined and systematized. The first section of the review is devoted to structural features and functions of biological immunoreceptors, viz., antibodies or their fragments. The main methods of antibody immobilization on the working electrode surface are considered in detail in the second section. The prospects for the development of electrochemical immunosensors are discussed in the third section of the review.     

Development of an immunosensor for the determination of rabbit IgG using streptavidin modified screen-printed carbon electrodes

Voltammetric enzyme immunosensors based on the employment of streptavidin modified screen-printed carbon electrodes (SPCEs) for the detection of rabbit IgG, as a model analyte, were described. Alkaline phosphatase (AP) and 3-indoxyl phosphate (3-IP) were used as the enzymatic label and substrate, respectively. The adsorption of streptavidin was performed by deposition of a drop of a streptavidin solution overnight at 4 °C on the pre-oxidized surface of the SPCEs. The analytical characteristics of these sensors were evaluated using biotin conjugated to AP.The immunosensor devices were based on a specific reaction of rabbit IgG with its biotinylated antibodies, which were immobilised on the modified screen-printed carbon electrodes through the streptavidin:biotin reaction. The immunosensors were used for a direct determination of AP labelled rabbit IgG, and for free rabbit IgG detection using a sequential competitive immunoassay. A calibration curve in the range of 5 × 10⁻¹¹ to 1 × 10⁻⁹ M of rabbit IgG was obtained with a estimated detection limit of 5 × 10⁻¹¹ M (7.0 ng/ml). These immunosensors were stable for 5 months if they were stored at 4 °C.     

Ultrasensitive electrochemical immunosensor for zeranol detection based on signal amplification strategy of nanoporous gold films and nano-montmorillonite as labels

Nano-montmorillonites belong to aluminosilicate clay minerals with innocuity, high specific surface area, ion exchange, and favorable adsorption property. Due to the excellent properties, montmorillonites can be used as labels for the electrochemical immunosensors. In this study, nano-montmorillonites were converted to sodium montmorillonites (Na-Mont) and further utilized for the immobilization of thionine (TH), horseradish peroxidase (HRP) and the secondary anti-zeranol antibody (Ab₂). The modified particles, Na-Mont-TH-HRP-Ab₂ were used as labels for immunosensors to detect zeranol. This protocol was used to prepare the immunosensor with the primary antibody (Ab₁) immobilized onto the nanoporous gold films (NPG) modified glassy carbon electrode (GCE) surface. Within zeranol concentration range (0.01–12 ng mL⁻¹), a linear calibration plot (Y = 0.4326 + 8.713 X, r = 0.9996) was obtained with a detection limit of 3 pg mL⁻¹ under optimal conditions. The proposed immunosensor showed good reproducibility, selectivity, and stability. This new type of immunosensors with montmorillonites and NPG as labels may provide potential applications for the detection of zeranol.     

Ultrasensitive Label‐free Electrochemical Immunosensors for Multiple Cell Surface Biomarkers on Liver Cancer Stem Cells

Liver cancer is one of the most widely spread cancers in the world. Cancer stem cells (CSCs) are a small subpopulation of liver cancer cells that are thought to be responsible for relapse of cancer and the resistance to chemotherapy. Detection of CSCs is highly demanded for screening patients who are at high risk for developing metastatic cancers. However, the current methodologies for CSCs detection are sophisticated, expensive and not reliable. Here, we report the development of a label‐free impedance immunosensors for liver CSC quantification using four established CSC surface biomarkers (CD44, CD90, CD133/2 and OV‐6). The immunosensors were simply fabricated by the covalent attachment of four biomarkers specific antibodies on gold electrodes using cysteamine/phenylene isothiocyanate linker. Electrochemical impedance spectroscopy was employed to detect the binding of the cells to the immunosensors. The binding of the CSCs to the gold electrode surface retards the access of ferri‐ferrocyanide redox molecules to the electrode leading to enhancement in the charge transfer resistance (R_ct) which represents the basis of the detection signal. The developed electrochemical immunosensors showed high sensitivity and selectivity for CSC detection with a wide linear range from 1 × 10¹ to 1× 10⁴ cells/mL with a limit of detection of 1 cell/ml. This work represents a new, accurate, simple and low cost method for the detection of liver CSC that might help in the early diagnosis of metastatic disease and cancer relapse.     

A Novel Label-free Chronoamperometric Immunosensor Based on a Biocomposite Material for Rapid Detection of Carcinoembryonic Antigen

In this research, poly(diallyldimethylammonium chloride)-capped gold nanoparticles, nickel ferrite particles, and carbon nanotubes were combined to form a PANC metal composite. The prepared metal composite modified onto a glassy carbon electrode was electropolymerized with poly(o-phenylenediamine) and immobilized with horseradish peroxidase, anti-carcinoembryonic antigen antibody, and bovine serum albumin to create the label-free immunosensors for rapid detection of carcinoembryonic antigen (CEA) using chronoamperometry. This developed biocomposite material modified onto a glassy carbon electrode presented an excellent electrocatalytic response to the redox reaction of hydrogen peroxide as a sensing probe, from which the kinetic parameters including of a charge transfer rate constant, a diffusion coefficient value, an electroactive surface area, and a surface concentration were calculated to be 1.85 s⁻¹, 4.28×10⁻⁶ cm² s⁻¹, 0.14 cm² and 1.87×10⁻⁸ mol cm⁻², respectively. The developed immunosensors also exhibited a wide linear range of CEA concentration from 0.01 to 25 ng mL⁻¹ with high sensitivity (96.21 μA cm⁻² ng⁻¹ mL) and low detection limit (0.72 pg mL⁻¹), excellent selectivity without interfering effects from possible species (amoxicillin, ascorbic acid, aspirin, caffeine, cholesterol, dopamine, glucose, and uric acid), outstanding stability (n=100, %I>50 %), repeatability (%RSD=0.34, n=10), reproducibility (%RSD=4.06, n=10), and rapid analysis (25 s each operation time). This proposed method was successfully applied for CEA detection in whole blood samples with satisfactory results, suggesting that this developed sensing platform may be considered to be exploited for fabrication of other label-free electrochemical immunosensors for the real sample analysis.     

Comparative evaluation of the performance of electrochemical immunosensors using magnetic microparticles and nanoparticles. Application to the determination of tyrosine kinase receptor AXL

Electrochemical sandwich immunoassay strategies involving the use of carboxyl-functionalized magnetic microbeads (cMBs) and magnetic nanoparticles (cMNPs) have been evaluated and compared. The proteolytically cleaved soluble tyrosine kinase receptor sAXL was used as the target analyte. Antibodies against AXL were covalently immobilized on cMBs or cMNPs. Immunobinding of AXL was detected by means of a secondary biotinylated antibody and a streptavidin-horseradish peroxidase conjugate. The electrochemical transduction was accomplished by capturing the cMBs or cMNPs bearing the immunoconjugates onto screen-printed carbon electrodes (SPCEs) by using a small magnet. The amperometric response was measured at ?0.20 V (vs the silver pseudo-reference electrode of the SPCE) upon the addition of H₂O₂ in the presence of hydroquinone as the redox mediator. The calibration plots for AXL extended up to 7.5 ng mL^?1 when cMBs were used for the preparation of the immunosensor and up to 40 ng mL^?1 in the case of using cMNPs. The respective slope values were 158 (cMBs) and 43 nA mL ng^?1 (cMNPs), while the achieved LODs were 74 (cMBs) and 75 pg mL^?1 (cMNPs). Although the immunosensors prepared with cMBs provided a shorter range of linearity, they exhibited a 3.7-times larger sensitivity than those constructed with cMNPs. The successful application of the new strategies was demonstrated for the determination of the endogenous content of sAXL in real human serum samples (a cut-off value of 71 ng mL^?1 have been established for patients with risk of heart failure). The immunosensors constructed using cMBs or cMNPs can be advanta geously compared, in terms of sensitivity and fabrication time, with the only immunosensor for AXL previously reported. In addition, these new immunosensors took approximately half time than ELISA to perform the assay.

Open image in new window

Graphical abstract Comparative evaluation of the performance of amperometric immunosensors for tyrosine kinase receptor AXL determination using carboxyl-modified magnetic microparticles (cMBs) and nanoparticles (cMNPs) and application to the determination of the endogeneous concentration in real human serum samples.

     

An amperometric immunosensor with a thiolated Protein G scaffold

The orientation of the analyte-specific capture antibody on the surface of electrochemical immunosensors plays an important role on their overall performance. We have employed a self-assembled layer of Protein G that was thiolated with succinimidyl-6-[3′-(2-pyridyldithio)-propionamido] hexanoate for the orientation-controlled immobilisation of a capture antibody in a flow-type amperometric immunosensor based on a two-site sandwich immunoassay. After establishing the formation of the thiolated Protein G layer on 1-mm screen printed electrodes, amperometric immunosensors for the detection of the hormone, human chorionic gonadotrophin (hCG), were successfully constructed upon this scaffold. These sensors were characterised by a limit of detection (based on three times the standard deviation of the blank signal) of 175 IU l⁻¹ and a linear response up to approximately 5000 IU l⁻¹ of hCG.     

Photoelectrochemical biosensing platform for the SARS-CoV-2 spike and nucleocapsid proteins

The COVID-19 pandemic is still a continuing worldwide challenge for public health systems. Early and ultrasensitive identification of the infection is essential for preventing the spread of COVID-19 by pre-symptomatic or asymptomatic individuals, particularly in the community and in-home settings. This work presents a versatile photoelectrochemical (PEC) immunosensor for SARS-CoV-2 detection based on a composite material formed by bismuth vanadate (BiVO₄) and strontium titanate (SrTiO₃). The PEC platform was denoted as BiVO₄/SrTiO₃/FTO, and it can be tuned for the detection of either Spike (S) or Nucleocapsid (N) protein by simply altering the antibody immobilized on the platform's surface. Chemical, morphological, and electrochemical characterizations were performed by X-Ray Diffraction, Scanning Electron microscopy, Energy-dispersive X-ray spectroscopy, Electrochemical Impedance Spectroscopy, and Amperometry. With a simple sensing architecture of the PEC platform, it was possible to achieve a linear response range of 0.1 pg mL⁻¹ to 1000 ng mL⁻¹ for S protein and 0.01 pg mL⁻¹ to 1000 ng mL⁻¹ for N protein. The PEC immunosensors presented recovery values for the two SARS-CoV-2 proteins in artificial saliva samples between 97 % and 107.20 % suggesting a good accuracy for the proposed immunosensors.     

Core–shell Fe3O4–Au magnetic nanoparticles based nonenzymatic ultrasensitive electrochemiluminescence immunosensor using quantum dots functionalized graphene sheet as labels

In this paper, a novel, low-cost electrochemiluminescence (ECL) immunosensor using core–shell Fe₃O₄–Au magnetic nanoparticles (AuMNPs) as the carriers of the primary antibody of carbohydrate antigen 125 (CA125) was designed. Graphene sheet (GS) with property of good conductivity and large surface area was a captivating candidate to amplify ECL signal. We successively synthesized functionalized GS by loading large amounts of quantum dots (QDs) onto the poly (diallyldimethyl-ammonium chloride) (PDDA) coated graphene sheet (P-GS@QDs) via self-assembly electrostatic reactions, which were used to label secondary antibodies. The ECL immunosensors coupled with a microfluidic strategy exhibited a wide detection range (0.005–50 U mL⁻¹) and a low detection limit (1.2 mU mL⁻¹) with the help of an external magnetic field to gather immunosensors. The method was evaluated with clinical serum sample, receiving good correlation with results from commercially available analytical procedure.     

High Sensitive Detection of Prostate Specific Antigen by Using Ferrocene Cored Asymmetric PAMAM Dendrimer Interface Screen Printed Electrodes

In this study, electrochemical immunosensors were developed for the detection of prostate specific antigen (PSA) using ferrocene (Fc) and polyamidoamine dendrimer (PAMAM) constructs. The biosensor fabrication was designed by modifying the screen‐printed gold electrode (Au) with ferrocene cored dendrimers (FcPAMAM) synthesized in three different generations. The self‐assembled monolayer principle was followed, to obtain sensitive, selective and disposable electrodes. Therefore, the Au electrodes were modified with cysteamine (Cys) to obtain a functional surface for FcPAMAM dendrimers to bind. Dendrimer generations were attached to this surface using a cross‐linker (glutaraldehyde) so that a suitable surface was obtained for binding of biological components. The Monoclonal PSA antibody (anti‐PSA) was immobilized on the Au electrode surface which coated with dendrimer, and (Au/Cys/FcPAMAM/anti‐PSA) biosensing electrode was obtained. The PSA detection performances of electrochemical impedance spectroscopy (EIS) and Amperometry based immunosensors exhibited very low detection limits; 0.001 ng mL^?1 and 0.1 pg mL^?1, respectively. In addition, EIS and Amperometry based biosensors using Au/Cys/FcPAMAM/anti‐PSA sensing electrode were represented excellent linear ranges of 0.01 ng mL^?1 to 100 ng mL^?1 and 0.001 ng mL^?1 to 100 ng mL^?1. In order to determine the applicability recovery and selectivity tests were performed using three different proteins in human serum.