Separation and Gas Chromatographic Determination of Free Styrene in Unsaturated Polyester Resins

Abstract

A rapid and efficient method for the separation and determination of free styrene in unsaturated polyester resin samples by gas chromatography was developed. A 10 cm pre-column connected to 1.2 m analytical column, both packed with 20 % carbowax 20M was used at 100°C with isobutylbenzene as an internal standard. Analysis time was two minutes with an accuracy of 0.3 %.     

A Simple Method for Producing Micrometer-Sized Monodisperse Polystyrene Particles in Aqueous Media

A method was developed for producing micrometer-sized, highly monodisperse polystyrene particles in single stage polymerization in aqueous media. The method employs an amphoteric surfactant, dimethyldodecylbetaine, that is added to the reaction system of styrene/K(2)S(2)O(8)/water in early stage of reaction. Polymerizations were carried out over a range of initiator concentrations (4-8 mmol/dm(3) H(2)O). The polymerization procedure could produce particles with an average diameter of 3.4 μm with a coefficient of variation of particle size distribution of 4.0%. Copyright 2000 Academic Press.     

An Optimized Method for the quantitation of Carboxyamidotriazole (CAI) in Human Plasma with Solid Phase Extraction and reversed Phase HPLC

Abstract

The anticancer agent CAI was quantitated from human plasma using a C-18 column with a mobile phase consisting of acetonitrile and water (each containing 0.01M ammonium acetate) pumped over a gradient at a flow rate of 1.0 mL min. The detection of CAI and the internal standard, harmine, was accomplished using a photodiode-array detector set at 264 and 323 nm, respectively. The chromatographic run time was 17.5 minutes. The plasma samples were prepared for HPLC analysis using a C-18 solid phase extraction procedure. Two calibration curves were prepared. and the assay was shown to be linear in the concentration range of 0.02 to 0.5 μg/mL for the low curve and 0.25 to 10.0 μg/mL for the high curve, with average correlation coefficients of 0.9933 and 0.9938, respectively. Intra-assay and inter-assay imprecisions were less than 10.0% with an error of accuracy of less than 11.0%. The assay was reproducible with the sensitivity needed for the prediction of CAI levels in the plasma of cancer patients.     

Solid phase extraction GC/ECD method for the analysis of organochlorine pesticides in wildlife plasma

A gas chromatographic method for the analysis of nine organo-chlorine pesticides in wildlife plasma is described. Reversed-phase solid phase extraction is utilized to extract the organochlorine pesticides from plasma. This is followed by a normal phase solid phase extraction clean-up as the pesticides are recovered by elution with hexane:ethyl ether (1:1) and quantified by gas chromatogra-phy/electron capture detection. Method limits of detection range from 7.0–25 μg/L. The mean recovery for all pesticides is 81%.     

Isolation and Determination of Volatile Organic Compounds from Water by Dynamic Purge-and-Trap Technique Coupled with Capillary Gas Chromatography

The preconcentration technique of purge-and-trap has been investigated in the present work for quantitative adsorption of volatile organic pollutants purged from water samples. A dynamic purging device with variable volume size has been constructed and tested to purge different concentrations of organic compounds. With Tenax GR as the adsorbent, a dynamic purge-and-trap technique was developed combining on-column preconcentration procedures using ambient trapping/thermal desorption/cryogenic focusing/back-flash injection prior to separation and determination using capillary gas chromatography. Various aromatic compounds in water were determined, giving linear working ranges over five orders of magnitude from 0.02 to 5000 µg/L. The analytical procedures were optimized under the assistance of ultrasonication with results validated for the determination of organic contaminants in underground water and tap water, giving over 93% recoveries and a detection limit of 0.01 µg/L, two orders of magnitude lower than those obtained using commercial available instruments with on-line configuration to minimize cross-contamination. The technique provides a potential automated method for in situ monitoring of volatile organic compounds in water.     

Determination of triclosan in human dental plaque by gas chromatography with atomic emission detection

A validated gas chromatographic method for the determination of triclosan in human dental plaque is described. Based on plaque sample weights of 10 mg, the limit of detection (2 × S/N) is 0.5 μg/g. The method is linear (r = 0.9986) from the limit of detection to 50 μg/g. Recoveries from placebos spiked with 2.0, 25, and 50 μg/g of triclosan were 105.6%±7.5%, 107.2%±3.1%, and 99.1%±1.1%, respectively (n = 3 at each level). Twenty replicate preparations and analyses of a homogenized sample, conducted by two operators over the course of 4 days, showed agreement to within 9% RSD. Analyses of dental plaque collected from patients after brushing with dental cream containing triclosan, shows triclosan to be retained in dental plaque at concentrations above the minimum inhibitory concentration (1 μg/g) after 12 h.     

气相色谱法同时测定水中12种挥发性消毒副产物

建立液-液萃取气相色谱法电子捕获检测器(GC/ECD)同时测定饮用水中12种挥发性消毒副产物(Disinfection byproducts, DBPs)的方法.采用过程标准校正降低预处理过程中引入的误差,方法检出限为0.08~0.21 μg/L, 全部组分在21.50 min内测定完成.不同浓度的DBPs在自来水和地表水中的回收率为80.9%~115.7%,相对标准偏差在0.9%~9.9%之间.各组分在0.5~200 μg/L浓度范围内线性关系良好,相关系数R>0.99.应用本方法测定了饮用水和地表水及其氯化后样品中DBPs的含量.本方法简便、快速、稳定,满足饮用水中挥发性DBPs的检测要求.     

Comparison of On-Column and Splitless Injections for the Capillary Gc Quantitation of Organics Extracted from Landfill Leachatesl

Abstract

An extensive study of the organic components of the leachate from the University of Connecticut landfill has been carried out. A modification of EPA Method 625 for base/neutral extractable organics was used to obtain both the gas chromatographic profiles and the mass spectrometric identification of the organics in groundwater samples from six test wells and several private wells in the vicinity of the landfill. A characteristic fingerprint representing a number of components was consistently found in the analysis of the landfill leachate but not in the drinking water of the private residences located on an adjoining road. Gas chromatographic parameters for optimum qualitative and quantitative analysis of field samples were determined using an acetone solution of the model leachate sample. It was confirmed that the on-column injection mode resulted in greater flame ionization detector (FID) response and more reproducible peak areas than the splitless mode. The major variable in obtaining reproducible data was the field sampling at the landfill, not the solvent reduction step or the injection mode used to introduce the sample into the gas chromatograph.     

Detection of volatile organic sulfur compounds in water by headspace gas chromatography and membrane inlet mass spectrometry

Two gas chromatographic methods, GC-FID (flame ionization detection) and GC-ELCD (electrolytic conductivity detector) are compared in tlie analysis of volatile organic sulfur compounds (VOSCs) in water samples with a membrane inlet mass spectrometry (MIMS) technique. Carbon disulfide, ethanethiol, dimethyl sulfide, ethyl-methyl sulfide, thiophene, and dimethyl disulfide were used as test compounds. Linear dynamic ranges were found to be two decades with the GC-ELCD method and four decades with the GC-FID and MIMS methods. Detection limits were at low (μg/1 levels with the two gas chromatographic methods and clearly below μg/1 level with the MIMS method. Analysis of one sample takes 40 min with the gas chromatographic methods and five minutes with the MIMS method. The selectivity was good, especially with the GC-ELCD and the MIMS method. In addition, quantitative results obtained with spiked water samples by the three methods are compared.     

β二酮钛配合物/MAO催化合成间规聚苯乙烯及其热性能

间规聚合;β二酮钛配合物/MAO催化合成间规聚苯乙烯及其热性能     

Polystyrene formation on monolayer-modified nitinol effectively controls corrosion

A surface-initiated polymerization of styrene on carboxylic acid terminated phosphonic monolayers was utilized to increase the corrosion resistance of nitinol and nickel oxide surfaces. Alkyl chain ordering, organic reactions, wettability, and film quality of the monolayers and polymers were determined by infrared spectroscopy, atomic force microscopy, matrix-assisted laser desorption ionization spectrometry, and water contact angles. The polystyrene film proved to be a better corrosion barrier than phosphonic acid monolayers by analysis with cyclic voltammetry and electrochemical impedance spectroscopy. The protection efficiency of the polystyrene film on nitinol was 99.4% and the monolayer was 42%.     

Trace Analysis of Methyl Tert‐butyl Ether in Water Samples Using New Ultrasound‐assisted Dispersive Liquid‐liquid Microextraction and Gas Chromatography‐flame Ionization Detection

In this study, simple and efficient ultrasound‐assisted dispersive liquid‐liquid microextraction combined with gas chromatography (GC) was developed for the preconcentration and determination of methyl‐tert‐butyl ether (MTBE) in water samples. One hundred microliters of benzyl alcohol was injected slowly into 10 mL home‐designed centrifuge glass vial containing an aqueous sample with 30% (w/v) of NaCl that was located inside the ultrasonic water bath. The formed emulsion was centrifuged and 2 μL of separated benzyl alcohol was injected into a gas chromatographic system equipped with a flame ionization detector (GC‐FID) for analysis. Several factors influencing the extraction efficiency such as the nature and volume of organic solvent, extraction temperature, ionic strength and centrifugation times were investigated and optimized. Using optimum extraction conditions a detection limit of 0.05 μg L^‐1 and a good linearity (r² = 0.998) in a calibration range of 0.1‐500 μg L^‐1 were achieved. This proposed method was successfully applied to the analysis of MTBE in tap, well and a ground water sam ple contaminated by leaking gasoline from an underground storage tank (LUST) in a gasoline service station.     

Microstructuring of Polystyrene Surfaces with Nonsolvent Sessile Droplets

Herein, we study the microstructuring of toluene‐vapor‐softened polystyrene surfaces with nonsolvent sessile droplets. Arrays of microvessels are obtained by depositing non‐evaporating droplets of ethylene glycol/water on the original polystyrene surfaces and subsequently exposing them to saturated toluene vapor. The droplets act as a mask on the polymer, thereby impeding the toluene vapor to diffuse and soften the polystyrene surface below them. Alternatively, the formation of microcraters at random positions—with an average depth‐to‐width aspect ratio of 0.5 and a diameter as small as 1.5 μm—is achieved by condensing water droplets on a softened polystyrene surface. The cross‐sections of the microvessels and the contact angle of the sessile water droplets suggest that the structures are formed by the combined action of the Laplace pressure at the bottom of the droplet and the surface tension acting at the three‐phase contact line of the droplets. As a support, the rim height and the depth of the microvessels are fitted with an elastic theory to provide Young’s modulus of the softened polystyrene surface.     

气相色谱法测烟草中拟除虫菊酯和有机磷类农残

建立了一种测定烟草中拟除虫菊酯类农药和有机磷类农药残留量的气相色谱法.用普通的聚苯乙烯凝胶柱代替昂贵的凝胶渗透色谱仪;层析柱填料用弗罗里硅土代替硅胶;用工作标准溶液过柱曲线作为标准曲线;有机磷类农药气相检测器用PFPD代替FPD.方法的检测量为0.01μg/g～0.04 μg/g,平均加标回收率为70.18%～95.86%,RSD为4.36﹪～9.96﹪,对样品进行了拟除虫菊酯类农药和有机磷类农药残留量的测定,结果满意.     

Size Exclusion Chromatographic Determination of PEG 3350 in Human Plasma and Urine

Abstract

A size exclusion chromatographic method is reported that quantitated PEG 3350 in human plasma and urine to a concentration of 10 μg/ml in plasma, or urine. The chromatographic system consisted of a 500 A gel permeation analytical column, a differential refractometer detector, and chloroform as the eluting solvent. Organic extraction was used as an initial separation technique. PEG 400 was used as the internal standard for PEG 3350, and showed similar extraction properties. Spiked plasma standards yielded standard calibration curves with correlation coefficients of greater than 0.99, and relative standard deviations (n=3) of 2.19% (500 μg/ml) and 6.97% (20 μg/ml). The analytical technique was used to estimate the elimination rate constant of PEG 3350 from 5 normal human subjects after oral administration of 240 grams of PEG 3350. K_E was found to be 0.1079 hr^?1 0.03781^?1 hr (mean s.d.) using the Sigma-minus data analysis method on total urines collected from the 5 subjects at varying intervals.     

Determination of volatile halogenated hydrocarbons in tap water,seawater and industrial effluents by glass capillary gas chromatography and electron capture detection

A rapid and sensitive method to determine volatile organohalides in different types of waters has been developed. The chromatographic system is based on the resolving power of the glass capillary column and the high sensitivity of the electron capture detector. The capillary columns were connected to the detector so that the eluate from the column is mixed with thermostatted purge gas to minimize band broadening due to dead volumes. The low column bleeding and decreased band spreading from capillary columns enhance the sensitivity to very low levels: 1 fg (10^?15g) for carbon tetrachloride, despite dilution of the column eluate by the purge gas. The water samples of 100 ml were extracted with 1 to 10 ml n-pentane which is the most practical alkane with respect to purity. When using high water to pentane ratios corrections had to be made, due to low extraction yield, to get accurate quantifications. A column with Carbowax 400 stationary phase permits direct tap water injection. The water peak concealed the substances eluated after CHCl₃ and CHBrCl₂. The gas chromatographic separation of haloforms in tap water could be shortened to 30 seconds using a 10 m SE–52 column with an increased film thickness. Besides tap water and seawater, industrial waste water from a pulp mill was analyzed. Ten different halogenated organic compounds, ranging from 1 ng/I to 760 μg/I, were quantified in the different waters. Bromoform, which had not previously been found in seawater, was detected. Chromatogram of a standard mixture containing 11 organohalides. Stationary phase, SE-52; 33 m × 0.3 mm i.d. inj. temp. 200°, column temp. 50°, interface 250°, detector temp. 250°. Helium carrier gas flow rate, 36 cm/s, scavenger'gas flow 30 ml/min. Split ratio 1:20, 1 = CH₂CI₂, 2 = CHC1₃, 3 = CH₃CC1₃, 4 = CC1₄, 5 = CHCICCI₂, 6 = CHBrCI₂, 7 = CBrC1₃, 8 = CHBr₂Cl, 9 = CCl₂CC1₂, 10 = CHCl₂l, 11 = CHBr₃.     

High Performance Liquid Chromatographic Determination of Pirenzepine Dihydrochloride in Its Pharmaceutical Formulation

Abstract

A high-performance liquid chromatographic procedure for the determination of pirenzepine dihydrochloride as a bulk material and in its tablet dosage form (Gastrozepin^R) is presented. Normal phase liquid chromatography has been performed on a Micro-pack Si-10 column using ammonium hydroxide (28–30% NH₃) in methanol (0.75: 99.25% v/v) as mobile phase at a flow rate of 2 ml/min. Clobazam has been used as internal standard with retention times of 1.9 and 2.8 minutes for clobazam and pirenzepine dihydrochloride, respectively at 254 nm. Analytical calibration yields a linear relationship between 5 and 25 μg/ml, with correlation coefficient of 0.999. Tablets each labelled to contain 25 mg pirenzepine dihydrochloride give mean percentage found of 99.98 ± 0.4. A plot of logarithm of concentration against time for a solution in 6 N hydrochloric acid gives a straight line with a slope of - 0.197 day^?1. The proposed method is, therefore, a stability indicating method.     

High Molecular Weight Polystyrene Obtained by Cationic Emulsion Polymerization Catalyzed by Imidazolium‐Based Ionic Liquid

The ionic liquid 1‐n‐butyl‐3‐methylimidazolium heptachlorodiferrate (BMI.Fe₂Cl₇) is efficiently used as catalyst in the cationic emulsion polymerization of styrene. The effect of different reaction temperatures, surfactant, and ionic liquid concentrations on polymer properties as molecular weight distribution and particle size is evaluated. High weight average molecular weights, above 1000 kDa, are achieved at 70% of conversion in 100 nm polystyrene particles formed mainly by micellar nucleation. Particle sizes and molecular weights increase with the decrease of the amount of surfactant. Even at low concentrations, BMI.Fe₂Cl₇/styrene molar ratio equal to 1/1000, the ionic liquid proves to be efficient for the emulsion polymerization of styrene, and lower ionic liquid concentrations lead to the formation of longer polymer chains.     

Identification of migratable substances in recycled high density polyethylene collected from household waste

High Density polyethylene regranules reprocessed from separated household waste collection were investigated for migratable con-taminants which were not present in virgin material. Although the material originated from different European reprocessors, the de-tected recycling-specific compounds were similar in most of the investigated samples. At a chosen threshold concentration of 0.5 μg/g more than 70 compounds were tentatively identified. Aroma compounds and preservatives were found in the range of 0.5 to 10 μg/g. Limonene, di(ethylhexyl) phthalate, and the isopropyl esters of myristic and palmitic acids were detected in concentrations up to 200 μg/g. These compounds were found in almost all the regranules. Most of the substances identified are constituents of personal hygiene products and cleaning agents and are therefore absorbed by the package during the storage. Owing to European food legislation and German cosmetics regulations, the use of such recycling packaging material appears suitable only for filling with technical products.     

Reversed-Phase High Performance Liquid Chromatographic and Thin Layer Chromatographic Methods for the Simultaneous Determination of Benazepril Hydrochloride and Hydrochlorothiazide in Cibadrex Tablets

ABSTRACT

Two procedures were developed for simultaneous determination of benazepril hydrochloride (I) and hydrochlorothiazide (II) in pure, laboratory made mixtures and in pharmaceutical dosage form “Cibadrex tablets® using reversed phase high performance liquid chromatographic and thin layer chromatographic methods.

For reversed phase HPLC, a new very sensitive, rapid, selective method was developed. The linearity ranges were 32-448 ng/20 μl and 40-560 ng/20 μl for benazepril hydrochloride and hydrochlorothiazide, respectively. The corresponding recoveries were 99.38 ± 1.526 and 99.2 ± 1.123.

The minimum detection limits were 7 ng/20 μl and 14 ng/20 μl for benazepril hydrochloride and hydrochlorothiazide respectively.

On the other hand, a new, simple, sensitive and fast thin layer chromatographic scanning densitometric method was developed for simultaneous determination of benazepril hydrochloride and hydrochlorothiazide using ethyl acetate: methanol: ammonia (85: 20: 10 v/v) as the developing system. The R_f values were 0.33 & 0.68 for benazepril hydrochloride and hydrochlorothiazide respectively. The minimum detection limit obtained was 0.12 μg/spot for benazepril hydrochloride and 0.24 μg/spot for hydrochlorothiazide. The mean percentage recoveries were 100.04 ± 1.102 and 99.31 ± 1.009 for benazepril hydrochloride and hydrochlorothiazide respectively.

The two proposed methods were simple, precise, sensitive and could be successfully applied for the determination of pure, laboratory made mixtures and pharmaceutical dosage forms. The results obtained were compared with those obtained by A ^1%.