Indirect Determination of Lidocaine by Atomic Absorption Spectrophotometry

Abstract

A new procedure for determining lidocaine chlorhydrate is described. The method consists of extracting an ion pair composed of Lidocaine and the inorganic complex Co(SCN)₄ ^2- into an organic solvent (1, 2 dichloroethane), then measure the Co in the organic phase by A.A.S. at 240.7 mm. Optimal experimental conditions concerning pH, Co(SCN)₄ ^?2 concentration, shaking time, phase ratio, number of extractions and linear range for calibration are studied. The method has a standard deviation of 10^?2. Two pharmaceutical preparations containing lidocaine, have been analyzed with very good results.     

Reply to W.H. Gries' comments on “Ion Implantation Standards as a Spark Source Mass Spectrometric Surface Analysis Calibration Technique.” Anal. Lett. 12(A10), 1123 (1979)

Abstract

The spectrophotometric determination of Bromhexi ne Canfosulfonate (BC) from the pair ionic makes with Co (SCN)₄ ⁼ and its extraction in chloroform was studied. The BC partition coefficient in the water-chloroform system was determined. The BC determination method was applied to syrups which contained Acetyl-Sulphamethoxi-pyridacine (ASMP), Sulphadimidine (SD), Guayacol-gly-ceryl-ether (GGE) and Sodium benzoate (SB). The method is exact and accurate.     

Bestimmung Von Molybdän Nach Extraction Mit O,O,S - Triäthyldithiophosphat

Abstract

The interaction of molybdenum(V) with potassium thiocyanate in a medium of O,O,S-triethyldithiophosphate [(C₂H₅O)₂P(S)SC₂H₅] and ethanol at a ratio 4:1 has been studied.

The stability constant of the molybdenum(V) thiocyanate complex was determined to be 7.6 × 10² with a molar ratio Mo(v) : SCN of 1:1. A new method based on the formation of the molybdenum-thiocyanate complex in the organic phase has been developed for the determination of molybdenum in steel.     

A Novel Optical Sensor for Determination of Thiocyanate

Abstract

A novel optical sensor (optode) is described for the determination of thiocyanate using methyltrioctylammonium chloride immobilized on triacetylcellulose membrane. The response to thiocyanate is the result of adsorption of [Co(SCN)₄]^2? on sensing membrane, which caused the colorless membrane to change to blue. This optode can readily be regenerated by using 0.02 mol/l sodium oxalate solution. The linear range of the method was 3.44×10^?5 to 8.61×10^?4 mol/l of thiocyanate with a limit of detection 1.51×10^?5 mol/l. The relative standard deviation for eight replicate measurements of 8.61×10^?5 and 4.30×10^?4 mol/l of thiocyanate was 3.45 and 1.23%, respectively. The sensor was successfully applied for the determination of thiocyanate in saliva of smokers, nonsmokers and various water samples.     

Analysis of Antihistamines in Cough Syrup

Abstract

An efficient and simple high performance liquid chromatography method was developed for determination of Ephedrine. Noscapine, Promethazine and Bromhexine in cough syrup. Cough syrup samples could be cleaned up by anionic exchange solid phase extraction disk. The method has been validated with good recovery, linearity, reproducibility and selectivity for simultaneous determination of common antihistamines in over-the-counter cough syrup mixtures.     

Indirect Determination of Pyrrolizidine Alkaloids by Flame Atomic Absorption Spectrometry

Abstract

This paper studies the formation and extraction of ion pairs of some alkaloids derived from pyrrolizidine. The substances studied are Nemorensine, Platyphylline, Senecionine and Seneciphylline, and the ion pairs studied and extracted are formed with Bil₄. The method consists of extracting an ion pair between the organic base and the inorganic complex, the metal is measured in the organic phase (1,2 dichloroethane) by Flame AAS. The optimal experimental conditions, pH, concentration of BiI₄ ^?, shaking time, phase ratio, number of extractions, and the range of calibration are studied for these substances. The linear range in organic phase is 0.13–1.91 mg.mL^?1. The standard deviation of the method varies between 2.4–3.2%, depending on the substance analyzed. The interferences produced by various substances are studied.     

Cyclohexane-1, 3-Dione bis (4-Methylthiosemicarbazone) as a Spectrophotometric Reagent for the Determination of Zn (II)

Abstract

The spectrophotometric study of reddish cyclohexane-1, 3-dione bis (4-methylthiosemicarbazone)-Zn(II) was made in dimethylformamide-water solution (λ_max= 475 nm, ∑ = 3.3×10⁴ 1.mole^?1. cm^?1. Sandell sensitivity = 2×10^?2 μg Zn(II).cm^?2, stoichiometry 1:1, and apparent stability constant 6.1×10⁴). A new method for the spectrophotometric determination of Zn(II) is proposed for concentrations between 0.1 and 2.5 ppm. The relative error (95% confidence level) is 0.7% for 1.0 pprn of Zn(II).

The extraction with ethylacetate of the reddish complex was also studied spectrophotometrically (λ_max = 493 nm, ∑ in organic phase = 4.8×10⁴ 1.mole^?1.cm. Sandell sensitivity = 3.4×10^?4 μg Zn(II).cm^?2, stoichiometry 1:1, apparent extraction constant 1.4×10⁴). A new method for the extraction-spectrophotometric determination of Zn(II) is proposed for concentrations, in aqueous phase, between 0.02 and 0.30 ppm. The relative error (95% confidence level) is 1.0% for 0.15 pprn of Zn(II).     

Separation of Iron(III) with Ammonium Thiocyanate‐H2O‐n‐Propyl Alcohol Extraction System in the Presence of Sodium Chloride

The behavior and conditions of liquid‐liquid extraction‐separation of Fe(III) by ammonium thiocyanate‐H₂O‐n‐propyl alcohol system in the presence of NaCl were studied, and the possible reactive mechanism of extraction of Fe(III) was deduced. The study showed that, in the presence of a given amount of NaCl, phases were separated thoroughly between n‐propyl alcohol and water. In the process of phase separation, the complex [Fe(SCN)_n]^(3‐n) formed by NH₄SCN and Fe(III) was quantitatively extracted into the n‐propyl alcohol phase. The extracted Fe(III) exists in the n‐propyl alcohol phase mainly as the forms of Fe(SCN)₂⁺ and Fe(SCN)₃. Also, the relationship between extraction yield of Fe(III) and the amount of NH₄SCN agreed well with the quadratic equation E = 0.54 + 58.14x ? 8.39x² (E and x represent the recovery rate of Fe(III) and the volume (mL) of 0.1 M NH₄SCN respectively). The quadratic R‐Square is 0.9990. With this method, Fe(III) can be completely separated from Co(II), Ni(II), Mn(II), Al(III), Bi(III) and Cd(II) at pH 1.0?2.0. The present method was applied in determining Fe(III) in samples with satisfactory results such as relative standard deviation from 2.06% to 2.89% and recovery rate in the range of 98.4?101.4%.     

Bioorganic Chemistry of Hypothiocyanite

Abstract

Hypothiocyanite (OSCN^?) plays an important role in the human host defense system as a nonimmunological antimicrobial agent. Although many conjugate reactions of proteins have been attributed to OSCN^?, there is little precedence for such reactions in small-molecule chemistry. We will discuss the derivative species that are in equilibrium with OSCN^?, including hypothiocyanous acid (HOSCN), thiocyanogen [(SCN) ₂ ], and trithiocyanate [(SCN) ₃ ^?], the first organic derivatives of this mixture to be fully characterized, and we will describe a new method of synthesizing hypothiocyanite.     

Spectrophotometric Determination of Palladium with Sodium Ethylene-Bis-Selendglycollate

Abstract

SUMMARY

Palladium was determined spectrophotometrically with sodium ethylene-bis-selenoglycollate in acid medium. The system obeys Beer' law in the range 0.25–0, 3 5 μg.ml^?1 and the molar absorptivity is 2.4 × 10⁴ 1. mol^?1 .cm^?1. Determination of palladium in the presence of many ions is reported.

In spite of the fact that selenium compounds have rarely been used as organic analytical reagents and one finds many palladium determination methods in the literature, this paper fits into the general Purpose reported before ^1,2 :systematic comparison of organic sulphur, sellenium and tellurium compounds as analytical reagents in agreement with propositions made some years agp ^3,4

In previous work⁵ the behaviour of the ethylseleno glycollic (L₁), selenodiglycollic (L₂) and ethylene-bis-selenoglycollic (L₃) anions in acidic solutions of some “soft”, “borderline” and “hard” cations was studied.

The results obtained for Pd(II) afforded evidences that its determination could be run with the three mentioned ligands.

Nevertheless, L₃ was selected because it provides the most sensitive signal and its synthesis is very simple and its overall yield is excellent⁶

From the qualitative study⁵ the foreseen selectivity could present some restrictions, but there is little doubt about the usefulness of the method that will be proposed, in various schemes of determination. Similar comments Beamish have been made about EDTA method for Pd(II) determination⁸     

Analysis of drugs by AAS via formation of ion pairs

A new procedure for determining nitrogenated bases by forming ion pairs with Fe(SCN)6^3– is studied. The method consists of extracting the ion pair formed by a nitrogenated base and the inorganic complex Fe(SCN)6^3– into an organic phase, and measuring the iron in the organic phase by AAS at 248.3 nm. The optimal experimental conditions for determining amylocaine, avacan, bromhexine, diphenhydramine and papaverine are studied. The organic phase used is 1,2-dichloroethane. The standard deviation of the method varies between 10^–1 and 10^–2. The interferences produced by various substances are studied.     

A New Reagent for Determination of Isocyanates in Working Atmospheres by HPLC Using UV or Fluorescence Detection

Abstract

A new liquid chromatographic method with increased sensitivity has been developed for the determination of isocyanates common in industrial environments. The isocyanates are converted to stable urea derivatives by reaction with 9-(N-methylaminomethyl)-anthracene. These derivatives were analyzed using high performance liquid chromatography on a bonded octadecylsilyl phase using isocratic elution with acetonitrile/water and detected either by a UV or a fluorescence detector. The method was applied to toluene 2, 4- and 2, 6-diisocyanate (2, 4- and 2, 6-TDI), hexamethylene diisocyanate (HDI) and 4, 4-diphenylmethane diisocyanate (MDI).

The influence of various salts on the retention of the reagent amine was studied, as well as the separation of the urea derivatives on different C₁₈-phases. The detection limit is about 1 · 10^?4 mg/m³ for the isocyanates investigated, using either UV or fluorescence detection. This means that the new method is ten to twenty times more sensitive than the previously described reversed phase LC method, which utilized N-4-nitrobenzyl-N-n-propylamine as reagent.     

Liquid Anion Exchange Studies and Separation of Mercury

Abstract

A new method is developed for the extractive separation of mercury from associated elements. Mercury is quantitatively extracted from 0.5 M acetic acid solution by aliquat 336 S, which acts as a liquid anion exchanger. The metal ion from the organic phase is stripped with sodium hydroxide solution and determined in the aqueous phase complexometrically. The extracted species is [2(R₄N⁺), Hg(OAc)₄ ^?2]. A working procedure for the selective separation of mercury from zinc, cadmium, nickel, cobalt, copper, bismuth and manganese is described.     

Darstellung,Kristallstruktur, Schwingungsspektren und Normalkoordinatenanalyse von [Co(NH3)6][Os(SCN)6]

Synthesis, Crystal Structure, Vibrational Spectra, and Normal Coordinate Analysis of [Co(NH₃)₆][Os(SCN)₆] From the mixture of the linkage isomers [Os(NCS)_n(SCN)_6–n]^3–, n = 0–2, pure [Os(SCN)₆]^3– has been isolated by ion exchange chromatography on diethylaminoethyl cellulose. The X‐ray structure determination on a single crystal of [Co(NH₃)₆][Os(SCN)₆] (trigonal, space group R 3, a = 12.368(2), c = 11.830(2) Å, Z = 3) reveals that the thiocyanate ligands are exclusively S‐coordinated with the Os–S distance of 2.388 Å and the Os–S–C angle of 108.8°. The IR and Raman spectra of (n‐Bu₄N)₃[Os(SCN)₆] are assigned by normal coordinate analysis based on the molecular parameters of the X‐ray determination. The valence force constant f_d(OsS) is 1.42 mdyn/Å.     

1,2-Dimorpholyl-?than als Reagens in der quantitativen Analyse

Zusammenfassung Es wird eine gravimetrische Zinkbestimmung über die Verbindungen [C₁₀H₂₀O₂N₂H₂][Zn(SCN)₄] und C₁₀H₂₀N₂O₂ · Zn(SCN)₂ berichtet.

---

Summary A method is described for the gravimetric determination of zinc via the compounds [C₁₀H₂₀O₂N₂H₂][Zn(SCN)₄] and C₁₀H₂₀N₂O₂ · Zn(SCN)₂.

---

---

Mit 7 Textabbildungen

---

IV. Mitt.: Asmus, E., u. P. Sarfert: diese Z. 198, 412 (1963).

---

Für die Durchführung dieser Arbeit wurden dankenswerterweise Forschungsmittel aus dem ERP-Sondervermögen bereitgestellt.Dem Verband der Chemischen Industrie und der Deutschen Forschungsgemeinschaft danken wir für die Unterstützung dieser Arbeit.     

Spectrophotometric Study of 1, 3-Cyclohexanedione Bisthiosemicarbazone Monohydrochloride -Bi (III) Complex. Determination of Bi (III)

Abstract

The spectrophotometric study was made of red-violet 1, 3-cyclohexanedione bis-thiosemicarbazone-Bi (III) in an acidic dimethylformamide-water solution (λ_max = 540 nm, ? = 3.3 × 10^?4 1. mol^?1. cm^?1, stoichiometry 3:1, apparent stability constant (6.0 × 10¹⁰). A new method for the spectrophotometric determination of Bi (III) is proposed for concentrations between 0.7 and 7.4 ppm. The relative error (95 % confidence level) is 0.5 % for 3.7 ppm of Bi (III).

The extraction with methyl isobutyl ketone of the red-violet complex was also studied spectrophotometrically (λ_max = 550 nm, ? = 3.34 × 10⁴ 1. mol^?1.cm^?1, stoichiometry 2:1). A new method for the extraction-spectrophotometric determination of Bi (III) is proposed for concentrations, in aqueous phase, between 0.2 and 1.2 ppm. The relative error (95 % confidence level) is 0.8 % for 0.9 ppm of Bi (III).     

A Watersoluble Sulfonatomethylated Calix[4]resorcinarene as Artificial Receptor of Metal Complexes

The binding of different sized and shaped metal complexes [Co(His)₂]ClO₄(1), [Co(en)₂C₂O₄]Cl (2) and [K18-crown-6]SCN (3)(en-ethylendiamine, His-L-histidynate-anion) with a new tetrasulfonatomethylcalix[4]resorcinarene([H₈X]Na4) was investigated in neutral and alkaline aqueous media by NMR and pH-metrictitration methods and compared with those of recently studied NMe₄Br (4). The resultsobtained indicate that the outer-sphere coordination of complexes 1–3 by[H₈X]^4- proceeds via the interaction of hydrophobic fragments of the guestswith both the negatively charged rim and the hydrophobic cavity as a -base. Thenature of binding does not change for cations 1, 2 and 4 on going from[H₈X]^4- in neutral to [H₄X]^8- in alkaline media, while the inclusionof 3 decreases on going from [H₈X]^4- to [H₄X]^8-.     

Thermodynamic Dissociation Constants for [MPy4(NO3)2]*2Py Clathrates (M=Mn,Co, Ni,Cu)

Abstract

Stoichiometry and thermodynamic parameters of the title clathrates dissociation have been studied with thermoanalytical and strain method techniques. The [MPy₄(NO₃)₂]^*2Py (M = Mn, Co, Ni) clathrates dissociate with collapsing clathrate porous phase and destruction of the host complex to give the respective tripyridine complexes and gaseous pyridine. The [CuPy₄(NO₃)₂]^*2Py dissociates with collapsing clathrate phase but giving the host [CuPy₄(NO₃)₂] complex as individual phase, with the tripyridine complex forming in further course of decomposition. The comparison of the thermodynamic dissociation parameters for the [MPy₄(NO₃)₂]^*2Py series with M = Mn, Co, Ni, Cu, Zn and Cd shows that the differences in the stability of the compounds do not correlate with structural parameters of the clathrates but depend on the nature of the metal cation in the host complex. Thermodynamic stability of these clathrate phases follows the general sequence of stabilty for complexes of the 3d transition metals known as Irwing-Williams sequence: Mn<Fe<Co<Ni<Cu>Zn. These results disclose the main issue of instability of the [MPy₄(NO₃)₂]^*2Py clathrates as instability of the respective host complexes.     

Doppelkomplexsalze des Thioharnstoffs und der Thiocyanat-Ionen mit den Übergangsmetallen Cd(II), Cu(II) und Co(II)

Three new double complex compounds with the following compositions were obtained:[Cd(thio)₄]·[Cd(SCN)₄],[Cd(thio)₄]·[Co(SCN)₄], [Cu(thio)₄] [Cd₂(SCN)₆].Some of their physical properties including melting points and electric conductivity have been determined. The study of their IR-spectra shows that the metal-thiourea bond in the complex cation is formed via the sulphur atom. The Co-SCN bond in the complex anion [Co(SCN)₄]^2– is formed through the nitrogen atom, and in [Cd(SCN)₄]^2– the cadnium-thiocyanate bond is probably formed with some groups through the sulphur atom, and with others through the nitrogen.In the complex anion [Cd₂(SCN)₆]^2– the IR spectral data show that a bridging bond is also formed.     

Flow Injection Determination of Chloride Ions with Spectrophotometric Detection

Abstract

A single-line FIA system with a stream-sample splitting device for chloride determination is presented. The analytical method is based on the Fe^3+/Hg(SCN)₂/Cl^? system and the absorbance of the red Fe(SCN)²⁺ species monitored spectrophotometrically at 480 nm. Using a stream-sample splitting device, the recorded signal is composed of two merged peaks. Three calibration curves were obtained, once injecting the standard solution series, two using the maximum heights of P₁ and P₂ peaks and one using the height of T trough. The FIA system showed three linear responses to the concentration of chloride in the ranges 10-100 ppm (P₁); 10-500 ppm (P₂) and 20-1000 ppm (T), respectively. Also, it was capable of detecting chloride ions in different types of water with a throughput of 15 samples h^?1 and the RSD for 240 ppm of Cl^? (n=10) were 1.67% (P₁); 2.38% (P₂) and 1.23% (T), respectively. The interference of several ions (commonly found in water) on the FIA outputs was investigated.