Electrochemical behavior of tartaric acid at CuGeO3 nanowire modified glassy carbon electrode

The electrochemical behavior of tartaric acid at the CuGeO₃ nanowire modified glassy carbon electrode has been investigated by cyclic voltammetry (CV). The results show that two pairs of semireversible electrochemical peaks are observed and can be assigned to the process of oxidation–reduction and adsorption–desorption of tartaric acid at the modified glassy carbon electrode, respectively. The intensity of the CV peaks increases linearly with the increase of the content of tartaric acid in the range of 0.01–5 mM and scan rate ranging from 25–200 mV s^?1. CuGeO₃ nanowire modified glassy carbon electrode exhibits good detection ability for tartaric acid in neutral solution with the detection limit of 8.9 and 7.7 μM for cvp1 and cvp2, respectively, at a signal-to-noise ratio of 3. The CuGeO₃ nanowire modified glassy carbon electrode has good reproducibility and stability.     

Polyfurfural-Electrochemically Reduced Graphene Oxide Modified Glassy Carbon Electrode for the Direct Determination of Nitrofurazone

An electrochemical sensor based on a polyfurfural-electrochemically reduced graphene oxide modified glassy carbon electrode has been developed for the sensitive and rapid determination of nitrofurazone. The morphologies and properties of the sensor were characterized by electrochemical impedance spectroscopy, scanning electron microscopy, cyclic voltammetry, and differential pulse voltammetry (DPV). In pH 7.0 Britton–Robinson buffer solution, the as-prepared polyfurfural-electrochemically reduced graphene oxide modified glassy carbon electrode shows excellent electrocatalytic performance for the electrochemical reduction of nitrofurazone, and the reduction peak current is about 9.45, 1.31, and 1.25 times higher than that of the bare glassy carbon electrode, polyfurfural modified glassy carbon electrode, and electrochemically reduced graphene oxide modified glassy carbon electrode, respectively. The DPV determination of nitrofurazone indicates that the linear range and detection limit of nitrofurazone are 1–50 and 0.25?µmol/dm³, respectively. In addition, this sensor exhibits high selectivity, reproducibility, stability, and also was successfully used to directly determine nitrofurazone in the commercial antibacterial lotion with comparative sensitivity to high-performance liquid chromatography, showing its promising application prospects.     

Electrochemical determination of L-cysteine using polyaniline/CuGeO3 nanowire modified electrode

The 10 wt % polyaniline/CuGeO₃ nanowire modified glassy carbon electrode has been used for the electrochemical determination of L-cysteine. The electrochemical behavior of L-cysteine at the 10 wt % polyaniline/CuGeO₃ nanowire modified glassy carbon electrode has been investigated. The intensities of the anodic cyclic voltammogram (CV) peaks of L-cysteine at the modified electrode increase linearly with the increase of the L-cysteine content in the range of 0.001–2 mM and scan rate ranging from 25 to 200 mV s^?1. 10 wt % polyaniline/CuGeO₃ nanowire modified glassy carbon electrode exhibits good reproducibility, stability and low detection limit of 1.7 and 0.44 μM for cvpl and cvp2, respectively. The polyaniline combined with the CuGeO₃ nanowires can improve the electrochemical detection ability of L-cysteine.     

Voltammertric Behaviour of Clonixin and its Differential Pulse Polarographic Determination in Tablets

ABSTRACT

Clonixin, a non-steroid analgesic, can be both reduced at the mercury electrode and oxidised at the glassy carbon electrode. The anodic response shows well-defined waves in a pH range between pH 2-12. The polarographic response shows two irreversible waves or peaks in the range between pH 1-6 shifting cathodically when pH increases. Above pH 7.0 all the signals disappeared. The first signal in the dpp mode at pH 1.8 was selected for analytical use. The polarographic     

Amperometric Nitric Oxide Sensor Based on Poly(Thionine)/Nafion‐Modified Electrode and Its Application in Monitoring Nitric Oxide Release from Rat Kidney

Abstract

A novel amperometric nitric oxide (NO) sensor based on a glassy carbon electrode modified with thionine and Nafion films has been developed. The oxidation peak current of NO increased significantly at the poly(thionine)/Nafion‐modified glassy carbon electrode (GCE), which can be used for the detection of NO. The oxidation peak current was linear with the concentration of nitric oxide over the range from 3.6×10^?7 to 6.8×10^?5 mol · L^?1, and the detection limit was 7.2×10^?8 mol · L^?1. This nitric oxide sensor showed high selectivity to nitric oxide determination, and some potential interference could be eliminated effectively. The nitric oxide sensor has been applied to monitor NO release from rat kidney stimulated by L‐arginine. The results indicated the applicability of the NO sensor to biomedical samples.     

Glucose Biosensor Based on Multi‐Walled Carbon Nanotube Modified Glassy Carbon Electrode

An amperometric glucose biosensor based on multi‐walled carbon nanotube (MWCNT) modified glassy carbon electrode has been developed. MWCNT‐modified glassy carbon electrode was obtained by casting the electrode surface with multi‐walled carbon nanotube materials. Glucose oxidase was co‐immobilized on the MWCNT‐modified glassy carbon surface by electrochemical deposition of poly(o‐phenylenediamine) film. Enhanced catalytic electroreduction behavior of oxygen at MWCNT‐modified electrode surface was observed at a potential of ?0.40 V (vs. Ag|AgCl) in neutral medium. The steady‐state amperometric response to glucose was determined at a selected potential of ?0.30 V by means of the reduction of dissolved oxygen consumed by the enzymatic reaction. Common interferents such as ascorbic acid, 4‐acetamidophenol, and uric acid did not interfere in the glucose determination. The linear range for glucose determination extended to 2.0 mM and the detection limit was estimated to be about 0.03 mM.     

NADH oxidation using modified electrodes based on lactate and glucose dehydrogenase entrapped between an electrocatalyst film and redox catalyst-modified polymers

We have developed a simple and efficient method for the enhanced loading of silver nanoparticles onto carbon nanospheres, and how this method can be used to design an electrochemical sensor for hydrogen peroxide (HP). A glassy carbon electrode was modified with hemoglobin, carbon nanospheres, and by enhanced loading of silver nanoparticles onto the carbon nanospheres via spontaneous polymerization of dopamine. The hemoglobin exhibits a remarkable electrocatalytic activity for the reduction of HP. The electrochemical response to HP is linear range in the 1.0–147.0?μM concentration range, with a detection limit of 0.3?μM at a signal-to-noise ratio of 3.

Amperometric Enzyme Based Biosensor For the Detection of Xanthine Via Superoxide

Abstract

An amperometric enzyme modified carbon paste electrode for the detection of xanthinc by the xanthine oxidase catalyzed reaction is described. the product of the enzyme reaction monitored is the highly unstable radical superoxide, detected at O mV (vs SCE) poised potential. A dual working electrode configuration consisting of an enzyme modified carboa paste electrode and an unmodified glassy carbon electrode are utilized for this purpose.     

The NADH Electrochemical Detection Performed at Carbon Nanofibers Modified Glassy Carbon Electrode

In this work, the capability of carbon nanofibers to be used for the design of catalytic electrochemical biosensors is demonstrated. The direct electrochemistry of NADH was studied at a glassy carbon electrode modified using carbon nanofibers. A decrease of the oxidation potential of NADH by more than 300 mV is observed in the case of the assembled carbon nanofiber‐glassy carbon electrode comparing with a bare glassy carbon electrode. The carbon nanofiber‐modified electrode exhibited a wide linear response range of 3×10^?5 to 2.1×10^?3 mol L^?1 with a correlation coefficient of 0.997 for the detection of NADH, a high specific sensitivity of 3637.65 (μA/M cm²), a low detection of limit (LOD=3σ) of 11 μM, and a fast response time (3 s). These results have confirmed the fact that the carbon nanofibers represent a promising material to assemble electrochemical sensors and biosensors.     

Electrocatalytic Oxidation and Direct Determination of L-Tyrosine by Square Wave Voltammetry at Multi-wall Carbon Nanotubes Modified Glassy Carbon Electrodes

The electrochemical behavior of L-tyrosine was investigated at a multi-wall carbon nanotubes modified glassy carbon electrode. L-tyrosine itself showed a poor electrochemical response at the bare glassy carbon electrode; however, a multi-wall carbon nanotubes film fabricated on the glassy carbon electrode can directly enhance the electrochemical signal of L-tyrosine when applying cyclic voltammetry and square wave stripping voltammetry without any mediator. Cyclic voltammetry was carried out to study the electrochemical oxidation mechanism of L-tyrosine, which shows a totally irreversible process and an oxidation potential of 671 mV at the modified electrode and 728 mV at the bare electrode, ΔE_p = 57 mV. The anodic peak current linearly increases with the square root of scan rate in the low range, suggesting that the oxidation of L-tyrosine on the multi-wall carbon nanotubes modified electrode is a diffusion-controlled process. The square wave stripping voltammetry currents of L-tyrosine at the multi-wall carbon nanotubes modified electrodes increased linearly with the concentration in the range of 2.0 × 10⁻⁶–5.0 × 10⁻⁴ mol L⁻¹. The detection limit was 4.0 × 10⁻⁷ mol L⁻¹. The method is simple, quick, sensitive and accurate.     

Electrochemical Behavior of 8‐Azaguanine at DNA Langmuir–Blodgett Modified Glassy Carbon Electrode and Its Analytical Application

A highly sensitive electrochemical biosensor for the detection of trace amounts of 8‐azaguanine has been designed. Double stranded (ds)DNA molecules are immobilized onto a glassy carbon electrode surface with Langmuir–Blodgett technique. The adsorptive voltammetric behaviors of 8‐azaguanine at DNA‐modified electrode were explored by means of cyclic voltammetry and square wave voltammetry. Compared with bare glassy carbon electrode (GCE), the Langmuir–Blodgett film modified electrode can greatly improve the measuring sensitivity of 8‐azaguanine. Under the optimum experimental conditions, the Langmuir–Blodgett film modified electrode in pH 3.0 Britton–Robinson buffer solutions shows a linear voltammetric response in the range of 5.0×10^?8 to 1.0×10^?5 mol L^?1 with detection limit 9.0×10^?9 mol L^?1. The method proposed was applied successfully for the determination of 8‐azaguanine in diluted human urine with wonderful satisfactory.     

Sensitive Detection of NADH by Ferrocenylalkanethiol Functionalized Multiwall Carbon Nanotubes Electrodes

Abstract

The 6-ferrocenylhexanethiol (FcC₆SH) functionalized multiwall carbon nanotubes (MWNTs) modified glassy carbon electrode (FcC₆SH/MWNTs/GCE) was easily fabricated and used for the sensitive detection of NADH. Cyclic voltammetric and amperometric methods were used to study the behavior of NADH on the FcC₆SH/MWNTs/GCE. A broader linear response range to the NADH concentration from 5 µM to 1.5 mM with a correlation coefficient of 0.9982 was obtained. The detection limit was 0.54 µM. The synergetic effects of FcC₆SH and MWNTs make the modified electrode highly sensitive to NADH. In addition, the modified electrode can decrease the fouling of the electrode surface.     

Selective Voltammetric Determination of Uric Acid in the Presence of Ascorbic Acid at Ordered Mesoporous Carbon Modified Electrodes

A novel chemically modified electrode was fabricated by immobilizing ordered mesoporous carbon (OMC) onto a glassy carbon (GC) electrode. The electrocatalytic behavior of the OMC modified electrode towards the oxidation of uric acid (UA) and ascorbic acid (AA) was studied. Compared to a glassy carbon electrode, the OMC modified electrode showed a faster electron transfer rate and reduced the overpotentials greatly. Furthermore, the OMC modified electrode resolved the overlapping voltammetric responses of UA and AA into two well‐defined voltammetric peaks with peak separation of ca. 0.38 V. All results show that the OMC modified electrode has a good electrocatalytic ability to UA and AA, and has an excellent response towards UA even in the presence of high concentration AA.     

Electrocatalytic reduction of NAD+ at glassy carbon electrode modified with single-walled carbon nanotubes and Ru(III) complexes

A simple procedure was developed to prepare a glassy carbon electrode modified with carbon nanotubes and Ruthenium (III) complexes. First, 25 μl of dimethyl sulfoxide–carbon nanotubes solutions (0.4 mg/ml) was cast on the surface of the glassy carbon electrode and dried in air to form a carbon nanotube film at the electrode surface. Then, the glassy carbon/carbon nanotube-modified electrode was immersed into a Ruthenium (III) complex solution (direct deposition) for a short period of time (10–20 s for multiwalled carbon nanotubes and 20–40 s for single-walled carbon nanotubes). The cyclic voltammograms of the modified electrode in aqueous solution shows a pair of well-defined, stable, and nearly reversible redox couple, Ru(III)/Ru(II), with surface-confined characteristics. The attractive mechanical and electrical characteristics of carbon nanostructures and unique properties and reactivity of Ru complexes are combined. The transfer coefficient (α), heterogeneous electron transfer rate constants (k _s), and surface concentrations (Γ) for the glassy carbon/single-walled carbon nanotubes/Ru(III) complex-, glassy carbon/multiwalled carbon nanotubes/Ru(III) complex-, and glassy carbon/Ru(III) complex-modified electrodes were calculated using the cyclic voltammetry technique. The modified electrodes showed excellent catalytic activity, fast response time, and high sensitivity toward the reduction of nicotinamide adenine dinucleotide in phosphate buffer solutions at a pH range of 4–8. The catalytic cathodic current depends on the nicotinamide adenine dinucleotide concentration. In the presence of alcohol dehydrogenase, the modified electrode exhibited a response to addition of acetaldehyde. Therefore, the main product of nicotinamide adenine dinucleotide electroreduction at the Ru(III) complex/carbon nanotube-modified electrode was the enzymatically active NADH. The purposed sensor can be used for acetaldehyde determination.     

Electrocatalytic oxidation of hydrazine on poly(4-aminobenzene sulfonic acid)-modified glassy carbon electrode

Electrocatalytic oxidation of hydrazine (HZ) was studied on an stable modified glassy carbon electrode (GCE) based on poly (4-aminobenzene sulfonic acid) (4-ABSA) film. The 4-ABSA-modified glassy carbon electrode was prepared by electrochemical polymerization technique in phosphate buffer solution (PBS) (pH 7.0) and its electrochemical behavior were studied by cyclic voltammetry (CV). The polymer filmmodified electrode has very high catalytic ability for electrooxidation of HZ, which appeared as a reduced overpotential in a wide operational pH range of 5–10. Limit of detection (LOD) and limit of quantification (LOQ) were obtained as 1.31 × 10^–7 and 4.35 × 10^–7 M for CV; 7.89 × 10^–8 and 2.63 × 10^–7 M for CA, respectively. The results of experiments showed that prepared modified electrode have good stability, sensitivity and reproducibility for at least one month if stored dry in air.     

Amperometric Biosensors for Glucose Based on Layer‐by‐Layer Assembled Functionalized Carbon Nanotube and Poly (Neutral Red) Multilayer Film

Abstract

Multiwalled carbon nanotubes (MWNTs) were treated with a mixture of concentrated sulfuric and nitric acid to introduce carboxylic acid groups to the nanotubes. Conducting polymer film was prepared by electrochemical polymerization of neutral red (NR). By using a layer‐by‐layer method, homogeneous and stable MWNTs and poly (neutral red) (PNR) multilayer films were alternately assembled on glassy carbon (GC) electrodes. With the introduction of PNR, the MWNTs/PNR multilayer film system showed synergy between the MWNTs and PNR, with a significant improvement of redox activity due to the excellent electron‐transfer ability of carbon nanotubes (CNTs) and PNR. The electropolymerization is advantageous, providing both prolonged long‐term stability and improved catalytic activity of the resulting modified electrodes. The MWNTs/PNR multilayer film modified glassy carbon electrode allows low potential detection of hydrogen peroxide with high sensitivity and fast response time. As compared to MWNTs and PNR‐modified GC electrodes, the magnitude of the amperometric response of the MWNTs/PNR composite‐modified GC electrode is more than three‐fold greater than that of the MWNTs modified GC electrode, and nine‐fold greater than that of the PNR‐modified GC electrode. With the immobilization of glucose oxidase onto the electrode surface using glutaric dialdehyde, a biosensor that responds sensitively to glucose has been constructed. In pH 6.98 phosphate buffer, nearly interference‐free determination of glucose has been realized at ?0.2 V vs. SCE with a linear range from 50 µM to 10 mM and response time <10s. The detection limit was 10 µM glucose (S/N=3).     

Electrochemical Behavior of Hydroquinone at Poly (Acridine Orange)–Modified Electrode and Its Separate Detection in the Presence of o‐Hydroquinone and m‐Hydroquinone

Abstract

Poly (acridine orange) (PAO) film–modified electrode was prepared by the electrooxidation of Acridine orange on a glassy carbon electrode (GCE) for the detection of hydroquinone in the presence of o‐hydroquinone and m‐hydroquinone. The electrochemical behavior of hydroquinone on the modified electrode was investigated with respect to different solution acidity, scan rate, and accumulation time. A pair of sharp and well‐defined peaks was obtained at 0.45 and 0.42 V [vs. a saturated calomel electrode (SCE)] at the PAO film–modified electrode. The potential difference between this pair of cathodic and anodic peaks was decreased to only 30 mV as compared to the 241 mV that was obtained on the bare glassy carbon electrode (GCE). As to o‐hydroquinone and m‐hydroquinone, their corresponding oxidation peaks appeared at 0.55 V and 0.89 V (vs. SCE), respectively. The oxidation potential differences between these three isomers enabled the separate detection of hydroquinone. Under the optimum experimental situation, the oxidation peak current of hydroquinone was proportional to the concentration at the range of 6.8×10^?7–9.6×10^?5 M. The detection limit was been estimated as 3×10^?7 M with 130 s accumulation. This method was applied to the hydroquinone detection in tap water samples.     

Electrochemical reduction of dioxygen on Alizarin modified glassy carbon electrode in acidic medium

The catalytic behaviour of glassy carbon electrode modified by 1,2-dihydroxy antraquinone (Alizarin) was investigated. The electrocatalytic ability of modified electrode for the reduction of dioxygen was examined by cyclic voltammetry and rotating disk electrode (RDE) voltammetry techniques. The Alizarin modified glassy carbon electrode possesses excellent electrocatalytic abilities for dioxygen reduction over potential 400 mV lower than at the bare glassy carbon electrode. Hydrodynamic studies were performed to determine the heterogeneous rate constant for the reduction of O₂ at the surface of modified electrode. It was determined by Koutecky-Levich plot. The apparent diffusion coefficient of O₂ in O₂ saturated acidic solutions was estimated by using Levich equation. Studies show the involvement of four electrons in dioxygen reduction at the surface of this modified electrode.     

Preconcentration of Rutin at a Poly Glutamic Acid Modified Electrode and its Determination by Square Wave Voltammetry

Abstract

The voltammetric determination of rutin in 0.04 mol l^?1 B‐R buffer (pH 4.0) by square wave voltammograms (+0.41 V vs. Ag/AgCl_(sat.)) at a poly glutamic acid modified glassy carbon electrode was found to be several orders of magnitude lower than that on a bare glassy carbon electrode. Rutin can be preconcentrated on the films of poly glutamic acid and presented linear relationship from concentration of 7×10^?7 to 1×10^?5 mol l^?1 in 0.04 mol l^?1 B‐R buffer pH 4.0. The method was successfully applied to the determination of rutin in pharmaceutical formulation without any pretreatment.     

A Review of: “Pharmaceutical Applications of Membrane Sensors by Vasile V. Cosofret and Richard P. Buck CRC Press,Inc., Boca Raton,Florida, U.S.A. 1992, x+431pp. US$95.00/Outside US$114.00, ISBN:0-8493-4406-9”

ABSTRACT

The analytical performance of two modified electrodes (a tyrosinase biosensor and a glassy carbon electrode (GCE) covered with poly[Ni-(protoporphyrin IX)dimethyl ester]) in comparison with the bare electrode has been evaluated in a flow injection system using standard solutions of oleuropein and olive oil samples. The tyrosinase biosensor appeared to be an appropriate device for the selective determination of phenols, moreover it can be easily incorporated in an on-line system. This method was used to evaluate the stability of the samples.