Determination of Phthalate Esters in Wine Using Dispersive Liquid–Liquid Microextraction and Gas Chromatography

A simple and rapid efficient method was developed for the determination of phthalate esters using dispersive liquid–liquid microextraction followed by gas chromatography with flame ionization detection. A mixture of isopropanol (0.75 mL, dispersant) and carbon tetrachloride (30 µL, extractant) with sodium chloride (1%, w/v) was used for extraction. Under optimum conditions, the method provided linear calibration curves between 0.5 and 200 µg L^?1 for dibutyl phthalate, and 1.0 and 200 µg L^?1 for butyl benzyl phthalate, diethyl phthalate, and diisooctyl phthalate. The relative standard deviations for intra-day and inter-day analyses were less than 5.8% and 6.9%, respectively, with enrichment factors between 229 and 424. Two wine samples were analyzed with recoveries between 70.1% and 119.3%.     

LC Determination of Phthalate Esters in Water Samples Using Continuous-Flow Microextraction

A novel method, continuous-flow microextraction (CFME) combined with liquid chromatography (LC) with variable-wavelength detector (VWD), has been developed for the determination of three phthalate esters (dimethyl phthalate (DMP), diethyl phthalate (DEP), and di-n-butyl phthalate (DnBP)) in water samples. Experimental parameters including extraction solvent, solvent drop volume, flow rate of sample solution, extraction time and ionic strength, which affected the extraction efficiency, were studied and optimized. Under the optimum extraction conditions, the method yields a linear calibration curve in the concentration range of 10–10,000 ng mL^?1 for target analytes. The enrichment factors of this method for DMP, DEP and DnBP reached at 27, 44 and 20, respectively, and the detection limits were 2, 1 and 5 ng mL^?1, respectively. Good repeatability of extraction was obtained with relative standard deviations below 8.6%. The results demonstrated that CFME followed by LC-VWD is a simple and reliable technique for the determination of phthalate esters in water samples.     

Cloud Point Extraction Preconcentration of Trace Cadmium as 1-Phenyl-3-methyl-4-benzoyl-5-pyrazolone Complex and Determination by Flame Atomic Absorption Spectrometry

A new method for the determination of trace cadmium in water samples by flame atomic absorption spectrometry (FAAS) after cloud point extraction (CPE) is proposed. The method is based on the complexation of Cd with 1-phenyl-3-methyl-4-benzoyl-5-pyrazolone (PMBP) in the presence of non-ionic micelles of Triton X-100. The effect of experimental conditions such as pH, concentration of chelating agent and surfactant, equilibration temperature and time on cloud point extraction was studied. Under the optimum conditions, the detection limits are 0.64 ng mL^±1 with relative standard deviations (RSDs) of 2.1% (n = 10). The proposed method was applied to the determination of trace cadmium in water samples with satisfactory results.     

Flow injection-based cloud point extraction of phosalone and ethion in seawater of Chabahar Bay and determination by high-performance liquid chromatography: study of use of carbon nanotube and nanofibers as a column filler in flow system

This study presents an easy and cost-effective flow-based cloud point extraction (CPE) method for determining partial amounts of two organophosphorus pesticides (phosalone and ethion) in seawater by HPLC–UV–Vis. In continues CPE methodology, the effect of the different column packing type such as carbon nanotube, polyacrylonitrile nanofiber and fiberglass on pesticide extraction was investigated. The Triton X-100 was utilized as nonionic surfactant, and moreover, effect of different parameters such as pH, temperature, extraction time, surfactant concentration, type and volume of the eluent solution on the extraction efficiency was optimized. Under optimum conditions, the figures of merit of the method for phosalone and ethion were obtained as: the enrichment factor (172 and 166), line range (0.8–300 and 0.5–300 µg L^?1, R ² = 0.9973 and 0.9982), relative standard deviation in concentration of 200 µg L^?1 (%RSD = %5.4 and %7.99, N = 5) and limit of detection (LOD = 0.24 and 0.14 µg L^?1). The suggested method was successfully used for determination of phosalone and ethion in Chabahar Bay seawaters with satisfactory results.     

浊点萃取-火焰原子吸收光谱法测定矿渣中痕量金

研究了以双硫腙为络合剂,以非离子型表面活性剂Triton X-100为萃取剂的浊点萃取-火焰原子吸收光谱法(CPE-FAAS)测定痕量金(Ⅲ)的新方法。详细考察了溶液的pH值、络合剂和表面活性剂浓度、平衡温度和时间等条件对浊点萃取效果的影响。该方法的线性范围为0.05~0.8μg/mL,检出限为7.9 ng/mL,相对标准偏差为4.12%(n=11),回收率在98.0%~102.0%之间,用于矿渣中金的测定,结果满意。     

Development of a dispersive liquid–liquid microextraction (DLLME) method coupled with GC/MS as a simple and valid method for simultaneous determination of phthalate metabolites in plasma

Phthalates are ubiquitous environmental contaminants, and frequent biological monitoring of their metabolites (as toxic species of phthalates in human body) is highly recommended. A novel dispersive liquid–liquid microextraction (DLLME) coupled with Gas Chromatography–Mass Spectrometry (GC-MS) has been developed for the determination of seven phthalate metabolites in human plasma for the first time. Plasma proteins were efficiently precipitated by adding of 0.2mg dry trichloroacetic acid to 10 mL plasma samples, incubation and centrifuging. For DLLME, a mixture of extraction solvent (chlorobenzene, 10 µL) and dispersive solvent (acetonitrile, 750 µL) were rapidly injected into 5.0 mL aqueous sample for the formation of cloudy solution, the analytes in the sample were extracted into the fine droplets of chlorobenzene. After extraction, phase separation was performed by centrifugation and the enriched analytes in the sedimented phase were subjected to GC-MS analysis. All important parameters affecting DLLME performance were investigated and optimised. Under the optimum extraction condition, the method yields a linear calibration curve for all target analytes in the concentration range from 5 to 5000 ng mL^?1. The limits of detection and relative standard deviations for all phthalate metabolites were between 1.21–2.09 ng mL^?1 and 4.8–6.8%, respectively. This is a very simple, rapid and reproducible method, which requires low volume of sample and toxic solvents.     

Analysis of PAHs in Water and Fruit Juice Samples by DLLME Combined with LC-Fluorescence Detection

A simple, rapid and efficient method termed dispersive liquid–liquid microextraction combined with liquid chromatography-fluorescence detection, has been developed for the extraction and determination of polycyclic aromatic hydrocarbons (PAHs) in water and fruit juice samples. Parameters such as the kind and volume of extraction solvent and dispersive solvent, extraction time and salt effect were optimized. Under optimum conditions, the enrichment factors ranged from 296 to 462. The linear range was 0.01–100 μg L^?1 and limits of detection were 0.001–0.01 μg L^?1. The relative standard deviations (RSDs, for 5 μg L^?1 of PAHs) varied from 1.0 to 11.5% (n = 3). The relative recoveries of PAHs from tap, river, well and sea water samples at spiking level of 5 μg L^?1 were 82.6–117.1, 74.9–113.9, 77.0–122.4 and 86.1–119.3%, respectively. The relative recoveries of PAHs from grape and apple juice samples at spiking levels of 2.5 and 5 μg L^?1 were 80.8–114.7 and 88.9–123.0%, respectively. It is concluded that the proposed method can be successfully applied for determination of PAHs in water and fruit juice samples.     

Cloud point extraction and spectrophotometric determination of amaranth in food samples using nonionic surfactant Triton X-100 and tetrabutylammonium hydrogen sulfate

Cloud point extraction methodology was successfully employed for preconcentration of trace amounts of amaranth prior to its determination by spectrophotometry. The method was based on the extraction of amaranth as an ion pair with tetrabutylammonium ion from aqueous solution using Triton X-100 as non-ionic surfactant. The extracted surfactant rich phase was diluted with ethanol and its absorbance was measured at 518 nm by a spectophotometer. An optimum set of surfactant concentration, pH, equilibration temperature and time, tetrabutylammonium hydrogen sulfate and salt concentration were obtained. The calibration graph was linear in the range of 20–1600 ng ml^?1 of amaranth in the initial solution with r = 0.9993 (n = 12). Detection limit based on three times the standard deviation of the blank (3S_b) was 13.0 ng ml^?1 (n = 10), and the relative standard deviation (R.S.D) for 100 and 1000 ng ml^?1 of amaranth was 4.2 and 1.4% (n = 10), respectively. The proposed procedure was applied to the determination of amaranth in different food samples.     

Determination of Phthalates in Beverages by Headspace SPME-GC Using Calix[6]arene Fiber

A headspace solid-phase microextraction, in conjunction with gas chromatography using a novel sol–gel calix[6]arene-contained fiber for the determination of phthalate acid esters in non-alcoholic beverages is described for the first time. A Taguchi’s L₂₅ (5⁶) orthogonal array experimental design was introduced to optimize the extraction parameters such as extraction temperature, extraction time, salt concentration and stirring speed. Under the optimized conditions, the method showed linear response of three to five orders of magnitude with correlation coefficients (r) better than 0.995. Owing to the good selectivity and high sensitivity of this fiber to phthalate acid esters, the extraction was carried out in real beverage matrix and low detection limits of 0.015–0.298 μg L^?1 were achieved. The recoveries of standard addition tests amounted to 87.9–108.3% and the relative standard deviation values varied from 9.62 to 15.2%. The method was applied to the analysis of 12 kinds of beverages and bis-2-ethylhexyl phthalate was the sole analyte detected in these samples.     

Determination of photoinitiator 4‐methylbenzophenone in milk by cloud point extraction

An efficient and easy sample pretreatment methodology was proposed for the detection of photoinitiator 4‐methylbenzophenone from milk before high‐performance liquid chromatography. Appropriate conditions for demulsification were studied. The parameters affecting cloud point extraction, such as concentration of Tween‐20, electrolyte salt, equilibration temperature, and time, have been investigated. When the spiked level was 200–1000 μg/kg, the average addition standard recovery was 99.14–105.98% with the optimum cloud point extraction conditions (concentration of Tween‐20, 138 g/L; mass of anhydrous sodium sulfate, 0.75 g; equilibration temperature, 65°C; equilibration time, 30 min). To decrease the detection limits, further work about the organic solvent, shaking time, and ultrasonic parameters was carried. When the spiked level was 10–100 μg/kg, the average addition standard recovery was 70.40–106.91% with the optimum cloud point extraction and enrichment conditions (optimum cloud point extraction conditions; volume of cyclohexane, 30 mL; shaking time, 20 min; time of ultrasonic, 20 min; temperature of ultrasonic bath, 45°C).     

Cloud point extraction of Δ9-tetrahydrocannabinol from cannabis resin

A cloud point extraction coupled with high performance liquid chromatography (HPLC/UV) method was developed for the determination of Δ⁹-tetrahydrocannabinol (THC) in micellar phase. The nonionic surfactant “Dowfax 20B102” was used to extract and pre-concentrate THC from cannabis resin, prior to its determination with a HPLC–UV system (diode array detector) with isocratic elution. The parameters and variables affecting the extraction were investigated. Under optimum conditions (1 wt.% Dowfax 20B102, 1 wt.% Na₂SO₄, T?=?318 K, t?=?30 min), this method yielded a quite satisfactory recovery rate (~81 %). The limit of detection was 0.04 μg?mL^?1, and the relative standard deviation was less than 2 %. Compared with conventional solid–liquid extraction, this new method avoids the use of volatile organic solvents, therefore is environmentally safer.     

浊点萃取光度法测定水样中亚硝酸根

A new method for the determination of trace nitrite by spectrophotometric after cloud point extraction was proposed.The effects of experimental conditions such as acidity,concentration of chromogenic reagent and surfactant,equilibration temperature and time on cloud point extraction were discussed.Under the optimum conditions,a good linear relationship was obtained in the range of 4.0～200 μg/L of the nitrite(r=0.9998),the detection limits of 0.43 μg/L.The recoveries fell in the range from 97.7% to 102.4% an...     

Utilization of homogeneous liquid–liquid extraction followed by HPLC-UV as a sensitive method for the extraction and determination of phthalate esters in environmental water samples

A simple and sensitive method for the extraction of four phthalate esters including dimethyl phthalate (DMP), diethyl phthalate (DEP), benzyl butyl phthalate (BBP) and di-n-butyl phthalate (DBP) as well as their determination in water samples was developed using homogeneous liquid–liquid extraction (HLLE) and HPLC-UV. The extraction method is based on the phase separation phenomenon by the salt addition to the ternary solvent system. The extraction parameters such as type and volume of extracting and consolute solvent, concentration of salt, pH of sample and extraction time were optimized. Under the optimal conditions (extraction solvent: 100?µL CHCl₃; consolute solvent: 2.0?mL methanol; NaCl 15% (w/v) and pH of sample: 6.5) extraction recovery was in the range of 92–102%. Linearity was observed in the range of 0.5–300?µg?L^?1 for DEP and 0.6–300?µg?L^?1 for DMP, BBP and DBP. Correlation coefficients (r ²), limits of detection (LODs) and relative standard deviations (RSDs) were in the ranges of 0.9976–0.9993, 0.18–0.25 and 1.5–4.8%, respectively. The method was successfully applied for the preconcentration and determination of these phthalate esters in the several environmental water samples.     

Simultaneous kinetic–spectrophotometric determination of mycophenolate mofetil and mycophenolic acid based on complexation with Fe(III) using chemometric techniques

Determination of pharmaceutical analytes has been subjected to many investigations, especially in transplantations in which accurate and precise detection of drugs is of importance. In this study, a simple and fast complexation reaction has been employed for simultaneous kinetic–spectrophotometric determination of two immunosuppressant drugs, mycophenolate mofetil and its active metabolite mycophenolic acid, which is based on the reaction between drugs and Fe(III) ions in the presence of sodium dodecyl sulfate as anionic surfactant by standard addition method. The effect of influential parameters including type of surfactant, concentration of Fe(III) ions and pH of the solution on the complexation reaction has been studied, and SDS was chosen as suitable surfactant, while reaction proceeds with 0.1 M Fe(III) at pH 4. Multivariate curve resolution-alternating least squares has been employed for analyzing the multiset data obtained from augmentation of resulting standard addition matrices. Values for limit of detection of method have been calculated as 4.88 and 1.62 µg mL^?1 for mycophenolic acid and mycophenolate mofetil, respectively, and Beer’s law is obeyed over the concentration ranges 10–200 µg mL^?1 for MPM and 50–250 µg mL^?1 for MPA. The proposed method was successfully applied for determination of drugs in plasma serum samples. The accuracy and reliability of the method was further ascertained by recovery studies via standard addition procedure.     

Bamboo charcoal as a novel solid-phase microextraction coating material for enrichment and determination of eleven phthalate esters in environmental water samples

This study demonstrates the potential of bamboo charcoal as a novel and inexpensive solid-phase microextraction (SPME) coating material for enrichment and determination of organic pollutants in water samples. Bamboo charcoal was prepared and used as a SPME coating material. Eleven phthalate esters (PAEs) were used as model analytes, and gas chromatography–mass spectrometry was used for separation and detection. Important extraction conditions (ionic strength, stirring rate, and extraction time) and desorption conditions (desorption temperature and time) were systematically investigated and optimized. Linearity of 0.1–100 μg?L^?1 and correlation coefficients of 0.9992–0.9998 were obtained under optimum conditions. Inter-day and intra-day repeatability were 2.15–9.93 % and 1.89–9.85 %, respectively, and fiber-to-fiber reproducibility was 5.42–9.66 %. On the basis of a chromatographic signal-to-baseline noise ratio of three, the limits of detection reached 0.004–0.023 μg?L^?1. Satisfactory results were achieved when the bamboo coating was used for determination of 11 PAEs in real water samples. The experimental results indicate that bamboo charcoal has significant potential as a SPME coating material for rapid enrichment and sensitive determination of organic pollutants in environmental samples.     

Determination of Etofenprox in environmental samples by HPLC after anionic surfactant micelle-mediated extraction (coacervation extraction)

A method is described for determination of residues of the insecticide Etofenprox in environmental samples. Anionic surfactant micelle-mediated extraction (coacervation extraction) was evaluated for isolation of Etofenprox before HPLC. The optimum conditions used for extraction included: 0.09 g sodium dodecanesulfonate (SDoS), 3.1 mL (3.3, for concentrations below 0.04 mg L⁻¹) 12 mol L⁻¹ HCl, 5 min vortex stirring, 5 min centrifugation at 4000 rpm, 2 h equilibration time. The limits of quantification (LOQ) and detection (LOD) were 0.01 and 0.004 mg L⁻¹, respectively, and recoveries obtained from five real samples ranged from 94.33±2.48 to 100.13±2.71%. The precision of the method was good; relative standard deviations (RSD) were less than 7%.      

Determination of Triazine Herbicides in Aqueous Samples Using Solidification of a Floating Drop for Liquid-Phase Microextraction with Liquid Chromatography

Abstract

A rapid, simple, and efficient liquid-phase microextraction (LPME) method coupled with high-performance liquid chromatography and ultraviolet detection for the analysis of triazine herbicides was developed in this study. Under the optimum conditions, the enrichment factors and extraction recoveries were 33.0–72.6 and 11.2–23.2%, respectively. The detection limits (LODs) were in the range of 0.03–0.10 µg L^?1. The relative standard deviations for the determination of the triazine herbicides at μg L^?1 levels varied in the range 2.05–8.15%. The method was successfully applied in the determination of the triazine herbicides in aqueous samples with satisfactory results.     

Determination of trace vanadium in sea cucumbers by ultrasound-assisted cloud point extraction and graphite furnace atomic absorption spectrometry

An ultrasound-assisted cloud point extraction (CPE) procedure was used for preconcentration and determination of vanadium by graphite furnace atomic absorption spectrometry. The vanadyl(IV) complex with ascorbic acid form a hydrophobic complex with 4-(2-pyridylazo) resorcinol (PAR) in a micelle medium, which is stable under our working conditions, and followed by its extraction into Triton X-100 surfactant-rich phase. The main factors affecting CPE efficiency, such as pH, concentrations of PAR, ascorbic acid and Triton X-100, incubation temperature, frequency and equilibration time of ultrasonic bath were investigated in detail. Under the optimum conditions, preconcentration of 10 mL sample gave a preconcentration factor of 36.4 and a detection limit of 4.0 µg kg^?1. The proposed method was successfully applied to determination of vanadium in sea cucumbers with satisfactory results.     

Development of a cloud point extraction and preconcentration method for silver prior to flame atomic absorption spectrometry

The possibility was investigated of using 2-mercaptobenzothiazole (MBT) for Ag(I) concentration by micellar extraction at cloud point (CP) temperature and subsequent determination by flame atomic absorption spectrometry (FAAS). The method is based on the complexation of Ag(I) with 2-mercaptobenzothiazole (MBT) in the presence of non-ionic micelles of Triton X-114. The effect of experimental conditions such as pH, concentration of chelating agent and surfactant, equilibration temperature and time on cloud point extraction was studied. Under the optimum conditions, the preconcentration of 10 mL of water sample in the presence of 0.1% Triton X-114 and 2 × 10⁻⁴ mol L⁻¹ 2-mercaptobenzothiazole permitted the detection of 2.2 ng mL⁻¹ silver. The calibration graph was linear in the range of 10–200 ng mL⁻¹, and the recovery of more than 99% was achieved. The proposed method was used in FAAS determination of Ag(I) in water samples.     

Rotating disk sorptive extraction of triclosan and methyl-triclosan from water samples

A method of sample preparation based on use of rotating disk sorptive extraction (RDSE) has been developed for determination of triclosan (TCS) and methyl-triclosan (MTCS) in water samples. The sorptive and desorptive behavior of the analytes was studied by use of a rotating disk coated with polydimethylsiloxane (PDMS) on one of its surfaces. Chemical and extraction behavior were studied to establish the best conditions for extraction. The optimum conditions for both analytes were: sample volume 25 mL, pH?4.5, NaCl concentration 6 % (w/v), disk rotational velocity 1,250 rpm, and extraction time 80 min. A desorption time of 30 min was used with 5 mL methanol. The detection limits for TCS and MTCS were 46 and 34 ng?L^?1, respectively. Recovery was evaluated at two concentrations, 160 and 800 ng?L^?1, and the values obtained were between 80 and 100 %. The method was applied to analysis of influent water at two treatment plants in Santiago, Chile.