The thermodynamic properties of star-shaped fullerene-containing poly-N-vinylpyrrolidone

The temperature dependence of the heat capacity of star-shaped fullerene-containing poly-N-vinylpyrrolidone was studied over the temperature range 6–390 K by precision adiabatic vacuum and dynamic scanning calorimetry. The temperature intervals and thermodynamic characteristics of phase transitions were determined. The low-temperature dependence of the heat capacity of the substance was analyzed according to the Debye theory of the heat capacity of solids and its multifractal generalization. The data obtained were used to calculate the standard thermodynamic functions C _p ^o (T),H ^o(T)-H ^o(0), S ^o(T), and G ^o(T)-H ^o(0) of fullerene-containing poly-N-vinylpyrrolidone from T → 0 to 390 K. The standard entropy of formation of the polymer from simple substances and the entropy of its synthesis from poly-N-vinylpyrrolidone and fullerite C₆₀ at 298.15 K were calculated. The thermodynamic characteristics of fullerene-containing poly-N-vinylpyrrolidone are compared with those of the polymer-analogue without C₆₀.     

ICP-AES内标法测定分子筛的组成

首次通过ICP-AES仪研究了分子筛化学组成全分析的方法，采用HNO3-HF混合酸密闭溶样，用H3BO3配合F^-，分别采用内标法和基体消除法消除基体效应．将研究结果与经典方法比较表明：采用本文研究的分析方法，结果准确可靠，符合分析要求，尤其对杂原子分子筛以及金属氧化物修饰的分子筛的组成分析具有应用价值．     

One-Pot Synthesis of Cellulose/MXene/PVA Foam for Efficient Methylene Blue Removal

Ti₃C₂T_x MXene has attracted considerable interest as a new emerging two-dimensional material for environmental remediation due to its high adsorption capacity. However, its use is greatly limited by its poor mechanical properties, low processability and recyclability, and the low dispersity of such powder materials. In this work, a porous adsorbent (C–CMP) containing cellulose nanocrystals (CNC), Ti₃C₂T_x MXene and polyvinyl alcohol (PVA) was prepared by a simple and environmentally-friendly foaming method. Glutaraldehyde was used as crosslinker to improve the mechanical properties and boost the adsorption efficiency of methylene blue (MB) molecules. Fourier transform infrared (FT–IR), elemental analysis (EDX) and thermogravimetric analysis (TGA) further confirmed that the preparation of the C–CMP foam and cross-linking reaction were successful. Scanning electron microscope (SEM) indicated that the macropores were distributed homogeneously. The adsorption experiment showed that maximum adsorption capacity of MB can reach 239.92 mg·g⁻¹ which was much higher than anionic dye (methyl orange, 45.25 mg·g⁻¹). The adsorption behavior fitted well with the Langmuir isotherm and pseudo-second-order kinetic models. Thermodynamic analysis indicated that the adsorption process was spontaneous and endothermic. Based on FT–IR, EDX and X-ray photoelectron spectroscopy (XPS) analysis, the adsorption mechanism between C–CMP and MB molecules was attributed to electrostatic interaction.     

A Hybrid Assembly of MXene with NH2−Si Nanoparticles Boosting Lithium Storage Performance

A facile hybrid assembly between Ti₃C₂T_x MXene nanosheets and (3‐aminopropyl) triethoxylsilane‐modified Si nanoparticles (NH₂?Si NPs) was developed to construct multilayer stacking of Ti₃C₂T_x nanosheets with NH₂?Si NPs assembling together (NH₂?Si/Ti₃C₂T_x). NH₂?Si/Ti₃C₂T_x exhibits a significantly enhanced lithium storage performance compared to pristine Si, which is attributed to the robust crosslinking architecture and considerably improved electrical conductivity as well as shorter Li⁺ diffusion pathways. The optimized NH₂?Si/Ti₃C₂T_x anode with Ti₃C₂T_x: NH₂?Si mass ratio of 4 : 1 displays an enhanced capacity (864 mAh g^?1 at 0.1 C) with robust capacity retention, which is significantly higher than those of NH₂?Si NPs and Ti₃C₂T_x anodes. Furthermore, this work demonstrates the important effect of the MXene‐based electrode architecture on the electrochemical performance and can guide future work on designing high‐performance Si/MXene hybrids for energy storage applications.     

Thermodynamic investigation of several natural polyols (II)

The low-temperature heat capacity C _p,m of sorbitol was precisely measured in the temperature range from 80 to 390 K by means of a small sample automated adiabatic calorimeter. A solid-liquid phase transition was found at T=369.157 K from the experimental C _p-T curve. The dependence of heat capacity on the temperature was fitted to the following polynomial equations with least square method. In the temperature range of 80 to 355 K, C _p,m/J K⁻¹ mol⁻¹=170.17+157.75x+128.03x ²-146.44x ³-335.66x ⁴+177.71x ⁵+306.15x ⁶, x= [(T/K)−217.5]/137.5. In the temperature range of 375 to 390 K, C _p,m/J K⁻¹ mol⁻¹=518.13+3.2819x, x=[(T/K)-382.5]/7.5. The molar enthalpy and entropy of this transition were determined to be 30.35±0.15 kJ mol⁻¹ and 82.22±0.41 J K⁻¹ mol⁻¹ respectively. The thermodynamic functions [H _T-H _298.15] and [S _T-S 298.15], were derived from the heat capacity data in the temperature range of 80 to 390 K with an interval of 5 K. DSC and TG measurements were performed to study the thermostability of the compound. The results were in agreement with those obtained from heat capacity measurements.     

NaY分子筛的改性及吸附脱氮性能

采用离子交换法用NH⁺₄、Zn²⁺、Cu²⁺、Cr³⁺阳离子改性NaY分子筛,并利用XRD、FT-IR和低温N₂吸附-脱附等方法对改性的分子筛进行了表征。XRD 和FT-IR表征结果表明,改性后的分子筛骨架完好。Cr改性Y分子筛(CrY)的比表面积、孔体积及平均孔径均较小,但存在部分介孔。研究了改性分子筛对含喹啉模拟燃料的吸附脱氮,喹啉分子尺寸的模拟结果为0.711 6 nm×0.500 2 nm,说明其并不易进入Y型分子筛0.74 nm的微孔。吸附脱氮结果表明,CrY的脱氮效果最好,CuY和ZnY次之,NH₄Y效果最差,改性分子筛的吸附脱氮性能与金属离子的价态有关,同价金属离子改性后的分子筛,吸附时间对其影响趋势相同,且金属离子价态越高,改性分子筛的吸附脱氮性能越好。吸附温度对CrY和NH₄Y分子筛吸附脱除喹啉的影响不大,可在室温下使用,但高温有利于CuY和ZnY吸附脱氮。XRD表征结果表明,焙烧后CrY分子筛骨架已完全塌陷失去了绝大部分吸附脱氮性能。     

NO_x分子在[Ag]-MAPO-5(M=Si,Ti)分子筛中的吸附

采用密度泛函理论(DFT)研究了银离子交换的硅磷酸铝([Ag]-SAPO-5)和钛磷酸铝([Ag]-TAPO-5)分子筛结构及其对NOx分子的吸附,获得吸附复合物的平衡几何结构参数和吸附能.结果表明,NOx分子以η1-N模式吸附在[Ag]-SAPO-5和[Ag]-TAPO-5分子筛中的结构更稳定,其吸附作用强度的次序为NO2NON2O.[Ag]-SAPO-5和[Ag]-TAPO-5对NO和NO2分子的活化程度要比N2O大.相比[Ag]-AlMOR,[Ag]-SAPO-5和[Ag]-TAPO-5对NOx分子的活化程度较大.还对[Ag]-SAPO-5和[Ag]-TAPO-5分子筛的抗硫、抗水及抗氧化性能进行了研究和分析.另外,通过自然键轨道(NBO)计算,分析了NOx分子与平衡离子Ag+之间的作用机理.     

Toward Understanding the Enhanced Pseudocapacitive Storage in 3D SnS/MXene Architectures Enabled by Engineered Surface Reactions

The optimization of three-dimensional (3D) MXene-based electrodes with desired electrochemical performances is highly demanded. Here, a precursor-guided strategy is reported for fabricating the 3D SnS/MXene architecture with tiny SnS nanocrystals (≈5 nm in size) covalently decorated on the wrinkled Ti₃C₂T_x nanosheets through Ti−S bonds (denoted as SnS/Ti₃C₂T_x-O). The formation of Ti−S bonds between SnS and Ti₃C₂T_x was confirmed by extended X-ray absorption fine structure (EXAFS). Rather than bulky SnS plates decorated on Ti₃C₂T_x (SnS/Ti₃C₂T_x-H) by one-step hydrothermal sulfidation followed by post annealing, this SnS/Ti₃C₂T_x-O presents size-dependent structural and dynamic properties. The as-formed 3D hierarchical structure can provide short ion-diffusion pathways and electron transport distances because of the more accessible surface sites. In addition, benefiting from the tiny SnS nanocrystals that can effectively improve Na⁺ diffusion and suppress structural variation upon charge/discharge processes, the as-obtained SnS/Ti₃C₂T_x-O can generate pseudocapacitance-dominated storage behavior enabled by engineered surface reactions. As predicted, this electrode exhibits an enhanced Na storage capacity of 565 mAh g⁻¹ at 0.1 A g⁻¹ after 75 cycles, outperforming SnS/Ti₃C₂T_x-H (336 mAh g⁻¹), SnS (212 mAh g⁻¹), and Ti₃C₂T_x (104 mAh g⁻¹) electrodes.     

AlMCM-41介孔分子筛的合成及表征

以拟薄水铝石为铝源、水玻璃为硅源、十六烷基三甲基溴化铵为模板剂,在110℃时水热晶化合成了含Al的MCM-41介孔分子筛.采用X射线衍射(XRD)、N2吸附-脱附、固体29Si、27Al魔角旋转核磁共振技术(MASNMR)、扫描电镜(SEM)及吡啶吸附傅里叶变换红外(FTIR)光谱技术对AlMCM-41分子筛进行了表征.结果表明:AlMCM-41分子筛具有六方排列的孔道结构,同时具有很高的相对结晶度、比表面积和孔容,且孔分布单一;AlMCM-41分子筛中Si原子在骨架内键合的程度更高,使AlMCM-41分子筛具有更好的骨架晶化程度;同时具有四配位骨架铝,使AlMCM-41介孔分子筛具有适当的酸性.     

The thermodynamic functions of fullerene derivative (<Emphasis Type="Italic">t</Emphasis>-Bu)<Subscript>12</Subscript>C<Subscript>60</Subscript> over the temperature range from <Emphasis Type="Italic">T</Emphasis> → 0 to 420 K

The temperature dependence of heat capacity C _p ^o = f(T) of fullerene derivative (t-Bu)₁₂C₆₀ has been measured by a adiabatic vacuum calorimeter over the temperature range T = 6–350 K and by a differential scanning calorimeter over the temperature range T = 330–420 K for the first time. The low-temperature (T ≤ 50 K) dependence of the heat capacity was analyzed based on Debye’s the heat capacity theory of solids and its fractal variant. As a consequence, the conclusion about structure heterodynamicity is given. The experimental results have been used to calculate the standard thermodynamic functions C _p ^o (T), H ^o(T)−H ^o(0), S ^o(T) and G ^o(T) − H ^o(0) over the range from T → 0 to 420 K. The standard entropy of formation at 298.15 K of fullerene derivative under study was calculated. The temperature of decomposition onset of derivative was determined by differential scanning calorimetery and thermogravimetric analysis. The standard thermodynamic characteristics of (t-Bu)₁₂C₆₀ and C₆₀ fullerite were compared.     

Resonant two-photon ionization of LiNa. Observation and preliminary characterization of five new singlet states

Supersonic molecular beams containing rotationally and vibrationally cold LiNa were probed by one- and multi-photon ionization. Results include determination of a vertical ionization potential (5.05 ± 0.04 eV) as well as first observation of five new singlet states. Preliminary spectroscopic constants (Te, w_e and w_ex_e) and term symbols are reported for these five states (A ¹Σ⁺, C¹ Σ⁺, D ¹Π, E¹ Σ⁺ and F¹ E⁺).     

Highly Efficient Adsorption of Bilirubin by Ti3C2Tx MXene

We discovered that the 2D Ti₃C₂T_x MXene sheet displays an ultra-high removal capability for bilirubin (BR). In particular, MXene shows 47.6 times higher removal efficiency over traditional activated carbon absorbents. The effect of MXene on the removal rate of BR in BR solution containing different concentrations of bovine serum albumin (BSA) was studied. The adsorption capacity of BSA for BR at high concentration of 5 g L⁻¹ was about 85% of the best adsorption capacity. The MXene before and after adsorption was characterized by SEM, FT-IR and XPS. Furthermore, MXene beads were prepared, and the hemoperfusion simulation experiment was carried out. The results show that the adsorption capacity of MXene for bilirubin can reach 1192.9 mg g⁻¹. This study suggests that MXene may be promising in the treatment of hyperbilirubinemia.     

The thermodynamic properties of bis(η6-o-xylene)chromium(I) fulleride over the temperature range from T → 0 to 340 K

The temperature dependence of the heat capacity of bis(η⁶-o-xylene)chromium(I) fulleride, [(η⁶-(o-xylene))₂Cr]^+?[C₆₀]^??, over the temperature range 6–340 K was measured on an adiabatic vacuum calorimeter. The low-temperature (20 K ≤ T ≤ 50 K) heat capacity was subjected to multifractal processing; conclusions about the heterodynamic character of the structure were drawn. The experimental data were used to calculate the standard thermodynamic functions C _p ^° (T), H ^°(T)-H ^°(0), S ^°(T), and G ^°(T)-H ^°(0) over the temperature range from T → 0 to 340 K and estimate the standard entropy of fulleride formation from simple substances at 298.15 K. The standard thermodynamic characteristics of [(η⁶-(o-xylene))₂Cr]^+?[C₆₀]^?? were compared with those of the initial fullerene C₆₀.     

Simultaneous Delamination and Rutile Formation on the Surface of Ti3C2Tx MXene for Copper Adsorption

In this work, we studied the formation of the rutile phase of titanium dioxide (TiO₂) on delaminated MXene (d‐Ti₃C₂T_x) flakes by the reaction of Ti₃C₂T_x with amino acids in water. Three types of amino acids with varied side‐chain polarity were used to delaminate Ti₃C₂T_x. d‐Ti₃C₂T_x flakes formed stable colloidal solutions due to the negative surface charges of chemisorbed amino acids on the d‐Ti₃C₂T_x. Rutile formed on d‐Ti₃C₂T_x at room temperature upon the intercalation of aromatic amino acids and subsequent sonication of the solution, while flakes intercalated with aliphatic amino acids did not oxidize. X‐Ray diffraction (XRD), transmission electron microscopy (TEM) and Raman spectroscopy revealed the nanosize rutile formation on the surface of Ti₃C₂T_x flakes. The XPS results indicated the surface functionalization of histidine on d‐Ti₃C₂T_x flakes. As‐synthesized histidine functionalized rutile TiO₂@d‐Ti₃C₂T_x hybrid was used for adsorption of Cu²⁺ ions from aqueous solution with a maximum uptake of 95 mg g^?1.     

Debye–Einstein model and anomalies of heat capacity temperature dependences of solid solutions at low temperatures

An approach is proposed for analysing the deviations of the heat capacity C_p(T) of solid solutions from the Kopp–Neumann rule (KNR) ΔC(T)?=?C_p(T)???C_KNR(T). Temperature dependences of the heat capacity C_p(T) of selected compositions of systems (InP)_x (InAs)_1?x and (GaAs)_x (InAs)_1?x at temperatures of 5–300 K are analysed in the Debye–Einstein approximation. It was established that in the case of substitution of atoms in the cation subsystem (Ga³⁺???In³⁺) with the same subsystem of anions (As^3?), the positive values of ΔC(T) at T?<?100 K are due to the appearance of the low-frequency Einstein mode, whereas the negative values of ΔC(T) at T?>?100 K are the result of a decrease in the fraction of the Debye contribution without changing the upper limit of the oscillation frequency. In the case of substitution in the cation subsystem (P^3????As^3?) with the invariant cation subsystem (In³⁺) to the low-temperature positive contribution of the additional low-frequency Einstein mode, a positive part is added from the modified Debye mode having the characteristic temperature θ_D below the additive value θ_DKNR. The adequacy of this model is confirmed by Raman scattering data.

     

Self-diffusion in melts of statistical copolymers: The effect of changes in microstructural composition

We have used nuclear reaction analysis to measure diffusion coefficients D in couples consisting of hydrogenated polybutadienes of structure (C₂H₃(C₂H₅))_x(C₄H₈)_1?x and their partly deuterated counterparts. The 1,2- and 1,4-olefinic isomers are randomly distributed along the chains and the mean vinyl fraction x varies between 0.38 and 0.94. We find that the effective monomeric mobility D₀ [defined by D = D₀(N_e/N²) for each copolymer, where N is the backbone length and N_e the entanglement spacing] decreases monotonically with increasing vinyl content x. Over the range of microstructures and temperatures T (?14?40°C) investigated we find log(D₀/T) varies smoothly with (T ? T_g), where T_g is the glass transition temperature of the respective melts. An analysis of our data in terms of a simple activated rate process model suggests that D₀ is controlled by thermally activated hopping of segments whose effective volume is close to that of the respective statistical segment lengths of the copolymeric chains. ©1995 John Wiley & Sons, Inc.     

On the study by D.S.C. of the unexpected ice melting at 0°C of emulsified aqueous saline solutions

Firstly, the behavior of droplets (Φ ≈ 1μm) of aqueous saline solutions dispersed within an emulsifying medium and subjected to steady cooling and heating is described. Droplets undergo freezing around a temperature T¹(x) and partial ice melting and total salt melting at the eutectic temperature T_E. This melting is followed by progressive melting of the remaining ice which ceases when the equilibrium temperature (T_e(x)) ice ⇆ solution is reached. Between T_e and T¹ the droplets are undercooled. Secondly, the results obtained when water crystallization occurs versus time at a fixed temperature _C, such as T¹(x) < > _C < T_e(x) are reported. During heating following crystallization at Θ_C, an unusual ice melting at 0° and/or ice melting ending at T & >; T_e(x) is noticed on the thermogram obtained by differential scanning calorimetry of the emulsion. This shows that pure ice or at all events less concentrated solutions must be present within the emulsion. A possible mechanism of crystallization at Θ_C is proposed.     

高硅 Na-ZSM-5 分子筛表面 NO 的常温吸附-氧化机理

 采用程序升温表面反应 (TPSR) 和原位漫反射红外光谱 (DRIFTS) 等手段研究了常温下 NO 和 O₂ 在高硅 Na-ZSM-5 分子筛上吸附-氧化反应机理. 结果表明, Na-ZSM-5 分子筛上 NO 的催化氧化过程中伴随着显著的 NO₂ 物理吸附, 表现为 NO 氧化和 NO₂ 吸附间的动态平衡. Na-ZSM-5 分子筛表面 NO_x 吸附物种的 TPSR 和原位 DRIFTS 表征表明, 化学吸附的 NO 和气相中的 O₂  在 Na-ZSM-5 表面反应生成吸附态的 NO₃, 并继续与 NO 作用生成弱吸附的 NO₂  和 N₂ O₄, 它们吸附饱和后释放出来; 其中, 强吸附的 NO₃ 在 NO 氧化过程中起到了反应中间体的作用, 同时也促进了 NO 的吸附.     

Chlorophyll-Based Organic Heterojunction on Ti3C2Tx MXene Nanosheets for Efficient Hydrogen Production

The Z-scheme process is a photoinduced electron-transfer pathway in natural oxygenic photosynthesis involving electron transport from photosystem II (PSII) to photosystem I (PSI). Inspired by the interesting Z-scheme process, herein a photocatalytic hydrogen evolution reaction (HER) employing chlorophyll (Chl) derivatives, Chl-1 and Chl-2, on the surface of Ti₃C₂T_x MXene with two-dimensional accordion-like morphology, forming Chl-1@Chl-2@Ti₃C₂T_x composite, is demonstrated. Due to the frontier molecular orbital energy alignments of Chl-1 and Chl-2, sublayer Chl-1 is a simulation of PSI, whereas upper layer Chl-2 is equivalent to PSII, and the resultant electron transport can take place from Chl-2 to Chl-1. Under the illumination of visible light (>420 nm), the HER performance of Chl-1@Chl-2@Ti₃C₂T_x photocatalyst was found to be as high as 143 μmol h⁻¹ g_cat⁻¹, which was substantially higher than that of photocatalysts of either Chl-1@Ti₃C₂T_x (20 μmol h⁻¹ g⁻¹) or Chl-2@Ti₃C₂T_x (15 μmol h⁻¹ g⁻¹).     

Effect of the amine type on thermal stability of modified mesoporous silica used for CO2 adsorption

In this study, the preparation by grafting of amino-functionalized SBA-15 molecular sieves was carried out. Amino-functionalized molecular sieves were synthesized using a silane coupling agent and different types of amination reagents which react with modified SBA-15. These composites were characterized by FT-IR spectroscopy, X-ray diffraction at low angles, nitrogen physisorption at 77 K, and evaluated by the adsorption of CO₂ and its temperature-programmed desorption—TPD. Thermal stability was investigated by TGA and DTA methods. In the view of a possible use of these amino-functionalized molecular sieves as sorbents for CO₂ removal, their adsorption–desorption properties towards CO₂ were also investigated by the TPD method. The mass loss of amino-functionalized molecular sieves above 215 °C was due to the oxidation and decomposition of amino propyl functional groups. This means that these composites could be used for adsorption of CO₂ at temperatures below 215 °C. The adsorption of CO₂ and its temperature programmed desorption using thermogravimetry were studied for amino-functionalized molecular sieves at 60 °C. The evolved gases during the adsorption–desorption of CO₂ on amino-functionalized molecular sieves were identified by online mass spectrometry coupled with thermogravimetry. CO₂ adsorption isotherms of functionalized samples at 60 °C showed that both the adsorption capacity (mg CO₂/g adsorbent) and the efficiency of amino groups (mol CO₂/mol NH₂) depend on the type of amination reagents and the amount of organic compound used.