PAH and PCB determination of the concentration gradient in moss Pleurozium schreberi near a highway,and seasonal variability at the background reference site

Moss (Pleurozium schreberi) was investigated as biomonitor of atmospheric polycyclic aromatic hydrocarbons (PAHs) and polychlorinated biphenyls (PCBs). Samples were collected at a distance of 10, 50 and 100 m from a highway and were seasonally collected in a forest stand near a regional background air pollution station situated approximately 30 km from the highway. The samples from the background area were dried using two different techniques in parallel, air-drying and freeze-drying. Simultaneous pressurised liquid extraction of PAHs and PCBs was performed, followed by purification using gel permeation chromatography of the crude extract. The concentration of the 15 most important Environmental Protection Agency (EPA) PAHs was determined by gas chromatography coupled with ion-trap mass spectrometry with a selected ion storage acquisition programme, and the PCB concentrations were determined using a mass spectrometer operated in tandem mass spectrometry (MS/MS) mode. Acceptable recoveries and quality parameters for PAHs and PCBs were achieved with the use of pressurised liquid extraction followed by gel permeation chromatography. The detection limit was <0.76 ng g^?1 for PAHs and <0.04 ng g^?1 for PCBs. Possible contamination of the moss samples by 3-ring PAHs and PCBs in the atmosphere was found during air drying. Increased PAH and PCB concentrations caused by car engine exhausts and by asphalt and oil evaporation were found near the highway. Generally, the PAH and PCB concentrations in moss decreased exponentially with distance from the highway. The organic compound concentrations close to the background station showed seasonal fluctuations corresponding to the fluctuations in the local air temperature and particle concentration.     

Matrix Solid-Phase Dispersion Combined with GC–MS/MS for the Determination of Organochlorine Pesticides and Polychlorinated Biphenyls in Marketed Seafood

An analysis method based on matrix solid-phase dispersion (MSPD) and gas chromatography tandem mass spectrometry was developed and applied for the analysis for organochlorine pesticides (OCPs) and polychlorinated biphenyls (PCBs) in the marketed seafood such as fish, shrimp and shellfish. The parameters of the method including the type and amount of the absorbent, as well as the type and volume of the elution solution were optimized. The recoveries were between 70 and 120% with RSDs less than 20%, and the LODs and LOQs were 0.011–0.046 and 0.037–0.153 ng g^?1 under optimized conditions. The results showed that most of the OCPs and PCBs were detectable in the marketed samples with the average concentration range of 0.722–14.206 and 0.034–1.184 ng g^?1, respectively. Among the 21 OCPs detected, DDTs had a relatively higher concentration level. And in the PCBs, the concentration of PCB28 was over 45% of the total PCBs determined in all the samples. The developed method was simple, fast and effective, and could successfully be applied for trace amount of OCPs and PCBs determination in seafood matrixes.     

Analysis of Dried Blood Spots for Polychlorinated Biphenyls and Organochlorine Pesticides by Gas Chromatography Coupled with Tandem Mass Spectrometry

Polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCs) are anthropogenic pollutants highly resistant to chemical degradation and readily absorbed by organic tissue. Their persistence in the environment and toxicological threat to mammals prompts swift, reliable methods of analysis. This study outlines a rapid, efficient and sensitive, validated methodology utilizing a simple liquid extraction technique, and subsequent analysis by gas chromatography coupled with tandem mass spectrometry (GC-MS/MS) for the determination of PCBs and OCs from dried blood spots. The PCBs and OCs were quantified in whole marine mammal blood spotted on Whatman Protein Saver cards (PSCs) by extracting the analytes into acetonitrile acidified with formic acid, followed by GC-MS/MS analysis. The samples were analyzed in positive electron impact (EI+) ionization mode with the electron energy set to 40?eV to preserve analyte integrity. Fortified blood with the analytes of interest was used for method validation and subsequent sample screening. The recoveries of targeted analytes ranged from 62.5% to 107.8%, with relative standard deviations ranging from 0.09% to 4.6% at a 100?ng·mL^?1 concentration level. The method detection limits were from 40.4?ng·g^?1 to 179.2?ng·g^?1 for the PCBs and 37.6?ng·g^?1 to 145.1?ng·g^?1 for the OCs. The use of dried blood spots provided for numerous advantages compared to whole blood samples while demonstrating reduced matrix effects and enhanced sample lifespan while retaining analyte sensitivity.     

Determination of pharmaceutical compounds in sewage sludge using a standard addition method approach

An analytical method for the simultaneous determination of eight pharmaceutical compounds in biosolids from urban wastewater treatment plants (WWTPs) was developed and validated. The compounds evaluated were non-steroidal anti-inflammatory drugs (naproxen, diclofenac, and ibuprofen), lipid regulators (clofibric acid), and antibiotics (sulfathiazole, sulfapyridine, sulfamethazine, and sulfamethoxazole). Ultrasound assisted extraction with a water–methanol solvent mixture (1:1, v:v) was performed and the compounds were then determined by liquid chromatography coupled with tandem mass spectrometry. The design of the method was based on the application of the standard addition calibration methodology to reduce matrix interferences. Validation procedures were conducted with rabbit excrements as blank samples. Recoveries of the target analytes ranged from 76 to 131% in spiked samples at 50, 200 or 1000 ng g^?1 dry weight (dw). The relative standard deviations were in the range of 5–15% and the method detection limits ranged from 2 to 12 ng g^?1dw. The method was applied to monitor pharmaceutical concentrations in biosolids from different WWTPs over an eight-month period (May to December 2011). Diclofenac, sulfapyridine and ibuprofen were detected in most of the samples whereas sulfamethazine and ibuprofen were the pharmaceuticals found in the highest concentrations (>200 ng g^?1 dw on average).     

A Pretreatment Method for GC–MS Determination of Endocrine Disrupting Chemicals in Mollusk Tissues

Automatic soxhlet extraction followed by silica gel cartridge cleanup process was developed as a pretreatment method for GC–MS determination of seven endocrine disrupting chemicals in mollusk tissues. Operation parameters including extraction time, adsorption flow rate and elution flow rate were optimized as 140 min, 2 mL min^?1 and 2 mL min^?1, respectively. Thirty percent dichloromethane in n-hexane and 70% dichloromethane in n-hexane were used as elution solvents in turn. Recovery rates were 93.7, 91.7, 84.5, 83.3, 88.4, 81.2, and 79.7% for nonylphenols (NPs), bisphenol A (BPA), 17α-ethynylestradiol (EE2), estrone (E1), 17α-estradiol (17α-E2), 17β-estradiol (E2), and estriol (E3), respectively. Acceptable relative standard derivations ranged from 8.5 to 12.1%. Method detection limits ranged from 0.27 to 0.68 ng g^?1 dry weight (dw), and quantitative detection limits ranged from 0.62 to 1.26 ng g^?1 dw. The method was successfully applied to five mollusk species in Dapeng Bay of China to verify its practicability, and NPs, BPA, EE2, E1 and 17α-E2 were detected in the range from 1.6 to 131.5 ng g^?1 dw.     

Analysis of Six Phenolic Endocrine Disrupting Chemicals in Surface Water and Sediment

An efficient and reliable method based on gas chromatography–mass spectrometry (GC–MS) was developed for the extraction and analysis of six phenolic endocrine disrupting chemicals (EDCs), such as 4-nonylphenol (4-NP), nonylphenol-mono-ethoxylate (NP1EO), nonylphenol-di-ethoxylate (NP2EO), 4-tert-octylphenol (4-t-OP), bisphenol A (BPA) and 4-cumylphenol (4-CP) in surface water and sediment. The method was developed by using microwave-assisted extraction (MAE), solid phase extraction (SPE) and derivatization procedure. The MAE procedures were performed by optimizing three key process factors, consisted of extraction solvent, extraction temperature and holding time, affecting the extraction efficiency from sediment samples. For SPE, various parameters that may affect the recovery efficiency of water samples, such as SPE phase cartridge, elution solvent, as well as pH of water samples, were investigated. A series of derivatization conditions, such as derivatization reagent, reaction temperature and reaction time, were improved. The method achieved good repeatability and reproducibility with relative standard deviations <13% for all target EDCs in the both samples. Satisfactory recoveries for spiked water and sediment samples ranged from 85 to 101% and 74 to 105%, respectively. The limits of quantification varied from 0.20 (4-t-OP) to 11.50 ng L^?1 (NP2EO) and from 0.31 (4-t-OP) to 9.50 ng g^?1 dry weight (dw) (NP2EO) for water samples and sediment samples, respectively. The established method was successfully applied to the analysis of target EDCs in surface water and sediment samples collected from Caohai site of Dianchi Lake, China. The results showed that NP1EO, NP2EO and BPA were the three dominant phenolic EDCs in the site, reaching 114, 97 and 149 ng L^?1 in surface water, while 444, 186 and 178 ng g^?1 dw in surface sediment, respectively.     

Development of Immunoaffinity Sample-Purification for GC–MS Analysis of Ractopamine in Swine Tissue

A method combining immunoaffinity chromatography with gas chromatography–mass spectrometry (GC–MS) has been established for determination of ractopamine residues in swine liver and urine. After clean-up on an immunoaffinity chromatography column, GC–MS analysis revealed recovery from blank swine liver and urine fortified at 2.5–20 ng g^?1 (ng mL^?1 for urine), respectively, was 68.2–78.6 and 76.2–83.1%. The limits of detection and quantification were 0.5 ng g^?1 (or ng mL^?1) and 2.0 ng g^?1 (or ng mL^?1), respectively. The procedure was used for analysis of ractopamine residues in samples of swine liver and urine in which the levels were unknown. The amounts detected were 9–216 ng g^?1 (ng mL^?1).     

A Novel Fiber with Phenyl-Functionalized MSU (Michigan State University) Coating for Solid-Phase Microextraction Combined with High Performance Liquid Chromatography for Preconcentration and Determination of Trace Polychlorinated Biphenyls in Environmental Water Samples

A novel and robust phenyl-functionalized MSU-1 (Ph-MSU) coated fiber for solid-phase microextraction (SPME) coupled to high performance liquid chromatography (HPLC) was developed for the preconcentration and the determination of 2,4,4′-trichlorobiphenyl (PCB 28), 2,4′,5-trichlorobiphenyl (PCB 31), 2,2′,5,5′-tetrachlorobiphenyl (PCB 52), 2,2′,4,5,5′-pentachlorobiphenyl (PCB 101), 2,3′,4,4′,5-pentachlorobiphenyl (PCB 118), 2,2′,3,4,4′,5′-hexachlorobiphenyl (PCB 138), 2,2′,4,4′,5,5′-hexachlorobiphenyl (PCB 153), and 2,2′,3,4,4′,5,5′-heptachlorobiphenyl (PCB 180) in environmental water samples. Experimental conditions affecting SPME were examined in detail. The Ph-MSU coating provided large porosity and short-range mesostructures necessary for high extraction capacity and rapid mass transfer of PCBs. The Ph-MSU coated fiber exhibited selectivity for PCB 28, PCB 31, PCB 118, and PCB 138 in a limited extraction time. Good linearity for all PCBs was obtained with correlation coefficients from 0.9987 to 0.9994. The recoveries were within 94.3% to 103% for the spiked water with 300 ng · L^?1 per PCB. The relative standard deviations (RSDs) ranged from 3.10% to 6.23% and the limits of detection (LODs) were between 8.73 ng · L^?1 and 13.8 ng · L^?1. The proposed method was applied for the determination of PCBs in real river water and rainwater samples. The median recoveries ranged from 85.6% to 118% with RSDs between 4.23% and 8.78%. The experimental results demonstrated that the Ph-MSU fiber coating could be reused for over 250 times without loss of the extraction efficiency. These results clearly indicate that the Ph-MSU coated fiber was rapid, sensitive, and suitable for the preconcentration and determination of trace PCBs in environmental water samples.     

An Improved Method for Determination of Polychlorinated Biphenyls and Polybrominated Diphenyl Ethers in Sediment by Ultrasonic Solvent Extraction Followed by Stir Bar Sorptive Extraction Coupled to TD–GC–MS

An improved simple, fast and miniaturized method for the determination of polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) in freshwater sediment using ultrasonic solvent extraction followed by stir bar sorptive extraction–thermal desorption–gas chromatography–mass spectrometry (USE-SBSE/TD–GC–MS) is presented. The sediment sample (0.2 g) is extracted with methanol (1:1.2, 2:1.0 mL) in an ultrasonic bath (two 5-min extraction cycles). The combined extracts are made up to 5 mL with water, and from the resulting solution, the analytes are preconcentrated on a stir bar coated with polydimethylsiloxane during 1 h of stirring. The loaded sorptive stir bar is then thermally desorbed and online analysed by GC–MS. For the analytes in river sediment, a linear dynamic range of 0.5–50 ng g^?1 was established and limits of detection in sub nanogram-per-gram level were achieved. Recoveries and repeatability were obtained in the ranges 62.8–91.5 % and 3.6–15.0 %, respectively. The method accuracy was confirmed by the analysis of PCBs and PBDEs in a certified reference material. The main improvement in comparison with similar published methods is in shortening the sample handling time and the method miniaturization.     

Trace analysis of benzophenone-derived compounds in surface waters and sediments using solid-phase extraction and microwave-assisted extraction followed by gas chromatography–mass spectrometry

This study describes a procedure for determining eight benzophenone-derived compounds in surface waters and sediments. These include the pharmaceutical ketoprofen, its phototransformation products 3-ethylbenzophenone and 3-acetylbenzophenone, and five benzophenone-type ultraviolet (UV) filters. The proposed analytical method involves the pre-concentration of water samples by solid-phase extraction (SPE) and microwave-assisted extraction (MAE) of sediment samples followed by derivatization and analysis by gas chromatography–mass spectrometry. Different parameters were investigated to achieve optimal method performance. Recoveries of 91 to 96 % from water samples were obtained using HLB Oasis SPE cartridges, whereas MAE of sediments (30 min at 150 °C) gave recoveries of 80 to 99 %. Limits of detection were between 0.1 and 1.9 ng L^?1 for water samples and from 0.1 to 1.4 ng g^?1 for sediment samples. The developed method was applied to environmental samples and revealed the presence of UV filters in the majority of the surface waters with up to 690 ng L^?1 of 2-hydroxy-4-methoxybenzophenone. By contrast, ketoprofen (≤2,900 ng L^?1) and its degradation products (≤320 ng L^?1) were found in only two rivers, both receiving wastewater treatment plant effluents. Sediment analysis revealed benzophenone to be present in concentrations up to 650 ng g^?1, whereas concentrations of other compounds were considerably lower (≤32 ng L^?1). For the first time, quantifiable amounts of two ketoprofen transformation products in the aqueous environment are reported.     

Determination of Triazine Herbicides and Diuron in Mud from Olive Washing Devices and Soils Using Gas Chromatography with Selective Detectors

Abstract

In the present work, a method for the simultaneous determination of five herbicides, diuron, simazine, atrazine, terbuthylazine and terbutryn by GC‐electron capture detection (ECD) and GC‐thermoionic specific detector (TSD) in soil and mud samples (from olives washing devices) has been developed. Extraction of the herbicides from soil samples was carried out by liquid–solid extraction with ciclohexane/acetone under sonication. In addition, a clean‐up step by solid phase extraction (SPE) using alumina was necessary for mud samples to remove fat residues in the extracts. Spiked soil standards were used for calibration. Limit of detection (LOD) values ranged between 0.2–1.4 ng g^?1 and limit of quantitation (LOQ) between 1.4–2.0 ng g^?1. The precision of the method was satisfactory for all the herbicides analyzed, with RSD values ranging between 7.5%–32.3% and 8.5%–17.8% for 10 and 100 ng g^?1 spiking levels, respectively. The accuracy of the method was checked at three spiking levels (10, 50, and 100 ng g^?1) with recovery values ranging from 74.2%–129.1%. In the case of mud samples, mean recovery values (100 ng g^?1 spiking level) were acceptable for diuron (69.5%) and more satisfactory in the case of triazine herbicides (81.0%–123.0%). Diuron and terbuthylazine were the herbicides most frequently detected in the analyzed samples.     

Quantification of Imidacloprid in Honeybees: Development of a Chemiluminescent ELISA

A Chemiluminescent Enzyme-Linked Immuno-Sorbent Assay (CL-ELISA) for determination and quantification of the fungicide imidacloprid in honeybees was developed in an indirect competitive format. The assay was optimized by determining: the optimal coating conjugate concentration and anti-imidacloprid antiserum dilution, the effect of the incubation time on the competitive step, and the tolerance to organic solvents. The IC₅₀ and the limit of detection (LOD) values were 14.8 ng mL^?1 and 0.11 ng mL^?1, respectively, similar to those of colorimetric ELISA with a calibration range of 0.1–2600 ng mL^?1. Cross reactivity of some related compounds such as three imidacloprid metabolites, 6-chloro nicotinic acid, 5-hydroxy-imidacloprid, and imidacloprid olefin, and one other chloronicotinoid insecticide, acetamiprid, were tested. The assay was then applied to honeybee extracts obtained by using the liquid-liquid extraction. The calibration curves in honeybee extracts from the liquid-liquid procedure gave an IC₅₀ of 23.7 ng mL^?1 and a LOD 1.6 ng mL^?1. The average recovery value from honeybee extracts spiked with 100 and 1000 ng mL^?1 of imidacloprid were 73% and 76%, respectively. Finally, the assay was applied to honeybee samples collected during monitoring activities in Italy; it was found that only five of the 27 samples were positives, with low concentrations of imidacloprid ranging between 1.2 and 15.4 ng g^?1.     

Determination of Two Pesticides in Soils by Dispersive Liquid–Liquid Microextraction Combined with LC-Fluorescence Detection

In the present work, a simple, rapid and sensitive sample pre-treatment technique, dispersive liquid–liquid microextraction (DLLME) coupled with liquid chromatography-fluorescence detection (LC-FLD), has been developed to determine carbamate (carbaryl) and organophosphorus (triazophos) pesticide residues in soil samples. Methanol was first used as extraction solvent for the extraction of pesticides from the soil samples and then as dispersive solvent in the DLLME procedure. Under the optimum extraction conditions, the linearity was obtained in the concentration range of 0.1–1,000 ng g^?1 for carbaryl and 1–5,000 ng g^?1 for triazophos, respectively. Correlation coefficients varied from 0.9997 to 0.9999. The limits of detection (LODs), based on signal-to-noise ratio (S/N) of 3, ranged from 14 to 110 pg g^?1. The relative standard deviation (RSDs, for 20.0 ng g^?1 of each pesticide) varied from 1.96 to 4.24% (n = 6). The relative recoveries of two pesticides from soil A1, A2 and A3 at spiking levels of 10.0, 20.0 and 50.0 ng g^?1 were in the range of 88.2–108.8%, 80.8–110.7% and 81.0–111.1%, respectively. The results demonstrated that DLLME was a sensitive and accurate method to determine the target pesticides, at trace levels, in soils.     

Bio Availability of Polychlorinated Biphenyl Congeners in the Soil to Earthworm (L. rubellus) System

Abstract

The earthworm's (Lumbricus rubellus) uptake of polychlorinated biphenyls (PCBs) from a soil contaminated with a commercial PCB formulation (Askarel at 150 μg g^?1) and their elimination of PCBs into a low contaminated soil (15 μg g^?1) has been studied. 17 individual congeners were monitored. The uptake and the elimination rate were similar for all PCB congeners notwithstanding their different chloro-substitution pattern which suggested that bioaccumulation of PCBs in earthworms is governed by passive, possibly diffusion controlled processes. The equilibrium state in the three-phase system, soil/soil water/earthworm was reached with a half-time around 3–4 days. The soil to earthworm bioconcentration factor ranged from 4 to 20 for tetra- to octa-chlorinated biphenyls and was weakly depending on the octanol-water partition coefficient: BCF = ?(1.3?1.8) × K _OW ^(0.35?0.40).     

Determination of 26 polychlorinated biphenyls congeners in soil samples using microwave-assisted extraction with open vessel and gas chromatography

A procedure focused on microwave-assisted extraction in open vessel (MAE-OV) and gas chromatography with electron capture detection (GC-ECD) was used for the determination of 26 congeners of polychlorinated biphenyls (PCBs) in soil samples. The limit of detection (LOD) and limit of quantification (LOQ) were evaluated for commercial PCBs mixture Aroclor1260. LOD and LOQ were calculated for each PCB congener, in the ranges (0.03–0.27?ng?g^?1) and (0.11–0.70?ng?g^?1), respectively. After optimization, 26 PCBs congeners were successfully extracted from soil samples with recovery amounts ranging between 84.7% and 117.3% for all PCBs congeners. The evaluated method of MAE-OV showed good separation and extraction of all PCBs congeners from soil samples. Extraction parameters such as solvent choice, power and extraction time were investigated. This study indicated that MAE-OV could be an interesting alternative method to extract PCBs from soils, since it is economical, easy, fast and requires low amounts of solvents.     

Polychlorinated naphthalene concentrations and profiles in cheese and butter,and comparisons with polychlorinated dibenzo-p-dioxin,polychlorinated dibenzofuran and polychlorinated biphenyl concentrations

Polychlorinated naphthalenes (PCNs) are candidates for inclusion in the Stockholm Convention on persistent organic pollutants. PCNs are structurally and toxicologically similar to 2,3,7,8-tetrachlorodibenzo-p-dioxin (2,3,7,8-TCDD) and its analogues. Intake in food is considered to be an important human exposure pathway for PCNs. In this preliminary study, cheese and butter samples were analysed for PCNs, polychlorinated dibenzo-p-dioxins (PCDDs), polychlorinated dibenzofurans (PCDFs) and polychlorinated biphenyls (PCBs) using an isotope dilution gas chromatography high-resolution mass spectrometry method. The aim of this study was to evaluate the PCN concentrations in the cheese and butter samples and to compare them with the PCDD, PCDF and PCB concentrations. The PCN concentrations were 5.6–103 pg g^?1 of wet weight in the seven cheese samples tested and 5.0–199 pg g^?1 of wet weight in the seven butter samples tested. The mass concentrations of lower chlorinated congeners were greater than those of the higher chlorinated congeners. Congeners of CN45/36, CN27/30 and CN33/34/37 were much more abundant than other congeners found in tetrachlorinated PCNs. Congeners of CN51, CN66/67 and CN73 were determined to be the predominant congeners in penta-, hexa- and heptachlorinated homologs, respectively. The PCNs contributed around 5% of the total PCN, PCDD, PCDF and PCB toxic equivalence (TEQ) values. CN73 was found to be the dominant PCN congener and contributed more than 40% to the PCN TEQ value. Congeners CN66/67, CN69 and CN63 were also found at relatively high levels. The PCB congener CB118 was the predominant congener (by mass-based concentration) of the 12 dioxin-like PCBs (dl-PCBs). The PCBs contributed 53.8% of the total TEQ, and congener CB126 contributed more than any other compound that was analysed to the total TEQ. The PCDDs and PCDFs contributed 11.6% and 29.7% of the total TEQ values, respectively.     

Determination of Protoberberine Alkaloids in Coptis chinensis by Microextraction and High Performance Liquid Chromatography

Sample preparation technique based on an organic filter membrane (pH-resolved filter membrane microextraction) (pH-RFMME) was developed, coupled with high-performance liquid chromatography, and used to determine protoberberine alkaloids (jatrorrhizine, epiberberine, coptisine, palmatine, and berberine) in Coptis chinensis at different pH values through a one-step procedure. This green procedure provides a desirable sample pretreatment technology. The main variables affecting the extraction such as filter membrane area (or volumes of extraction solvents), sample pH, eluent pH, ionic strength, extraction stirring rate, extraction time, and sample volume were optimized. Under the optimized conditions, the enrichment factors of the analytes were 40.4–52.0, the linear ranges were 3.2–6250 ng · mL^?1 for jatrorrhizine and epiberberine, 6.0–12000 ng · mL^?1 for coptisine, 1.8–3600 ng · mL^?1 for palmatine, and 18.8–18800 ng · mL^?1 for berberine, with r ² ≥ 0.9945. The limits of detection were less than 0.3 ng · mL^?1. Satisfactory recoveries (84.8%–115.5%) and precision (1.8%–10.0%) were also achieved. These results confirmed that pH-RFMME is a simple, rapid, practical, and environmentally friendly method to isolate analytes that exhibit significant differences in acidity or alkalinity from complex samples.     

Application of ultrasound-assisted emulsification microextraction for the determination of triazine herbicides in soil samples by high performance liquid chromatography

Ultrasound-assisted emulsification microextraction was applied to extract the herbicides simazine, atrazine, prometon, ametryn and prometryn from soil samples. They then were determined by HPLC with diode-array detection. Parameters that affect the extraction efficiency, such as the kind and volume of the extraction solvent, emulsification time and addition of salt, were optimized. Under the optimum conditions, the following analytical figures of merits are found: enrichment factors between 145 and 222, limits of detection between 0.1 to 0.5 ng g^?1, analytical linearity in the range from 1.0 to 200 ng g^?1, correlation coefficients (r) between 0.9989 and 0.9998, relative standard deviations from 2.8% to 3.6% (at n?=?5, intraday) and 3.7% to 4.3% (interday), and recoveries (at spiking levels of 5.0 and 50.0 ng g^?1) from 82.6% to 92.0%. The technique is simple, practical, rapid, and environmentally friendly.     

Measuring mercury in wood: challenging but important

Mercury (Hg) in tree wood has been overlooked, in part because concentrations are so low as to be below detection limits of some analytical methods, but it is potentially important to forest ecosystem processes and budgets. We tested methods for the preparation and determination of Hg in tree wood by analysing samples of four tree species at the Hubbard Brook Experimental Forest, New Hampshire, USA, using thermal decomposition, catalytic conversion, amalgamation and atomic absorption spectrophotometry (USEPA Method 7473). Samples that were freeze-dried or oven-dried at 65°C were suitable for determination of Hg, whereas oven-drying at 103°C resulted in Hg losses, and air-drying resulted in Hg gains, presumably due to sorption from indoor air. Mean (±SE) concentrations of Hg tree bole wood were 1.75 ± 0.14 ng g^?1 for American beech, 1.48 ± 0.23 ng g^?1 for sugar maple, 3.96 ± 0.19 ng g^?1 for red spruce and 4.59 ± 0.06 ng g^?1 for balsam fir. Based on these concentrations and estimates of wood biomass by species based on stand inventory, we estimated the Hg content of wood in the reference watershed at Hubbard Brook to be 0.32 g ha^?1, twice the size of the foliar Hg pool (0.15 g ha^?1). Mercury in wood deserves more attention and is feasible to measure using appropriate techniques.     

Trace metal analyses in honey samples from selected countries. A potential use in bio-monitoring

Honey is a sweet product made by bees using nectar from flowers. Concentrations of Ca, K, Mg, Fe, Zn, Mn, Cu, Pb and Cd were determined in 13 honey samples from the selected regions around the world. Levels of Ca, Mg, Cu, Fe, Zn and Mn were measured using flame atomic absorption spectrometry (FAAS). Potassium concentration was determined via flame photometry. Concentrations of Cd and Pb were determined using the electrothermal technique (ETAAS). It was estimated that the examined samples of honey from Greece, Turkey, Spain, Poland, Mexico, Argentina and Italy were of good quality in terms of metal concentrations (compliant with the norms referring to food products – WHO, Fifty-third Report of the joint FAO/WHO Expert Committee on Food Additives; Technical Report Series 776, Geneva), although the analysed samples were not free of heavy metals. The concentrations of the elements in the honey samples ranged from 2.38 to 9.31 μg · g^?1 for Zn, from 3.86 to 35.10 μg · g^?1 for Fe, from 0.19 to 21.64 μg · g^?1 for Mn, from 49.53 to 1006.90 μg · g^?1 for Ca, from 388.25 to 4761.50 μg · g^?1 for K and from 0.20 to 1.53 μg · g^?1 for Cu and regarding heavy metals from 0.11 to 2.78 μg · g^?1 for Pb and from 0.02 to 0.44 μg · g^?1 for Cd. According to these results it was found that the concentrations of heavy metals in the honey samples (except for alfalfa honey and eucalyptus honey from Italy) were under the acceptable limits for foods set out by the FAO/WHO. It was confirmed that the application of chemometric tools supports the extraction of significant information from analytical data, even though the availability of samples is not fully sufficient (this problem is often encountered in environmental analyses).