首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 312 毫秒
1.
《Analytical letters》2012,45(10):1843-1856
Abstract

A simple and sensitive ultraviolet spectrophotometric method has been devised for the determination of amikacin, kanamycin, neomycin and streptomycin in pure form and in some pharmaceutical preparations. The method depends on the nitrosation of the primary amino groups followed by reaction with cyanoacetamide in ammonia medium at 100°C for 30 min, The reaction products exhibit a characteristic absorption. maximum at 270 nm. Beer's law is obeyed within the concentration ranges 4–40 μg ml?1 for amikacin, kanamycin and neomycin and 8–80 μg ml?1 for streptomycin with apparent molar absorptivities of about 1.85 × 104 for the first three compounds and 1.3×104 1. mole?1.cm?1 for streptomycin.  相似文献   

2.
《Analytical letters》2012,45(8):1741-1750
Abstract

Ascorbic acid was determined indirectly by spectrophotometry at 666 nm based on the photochemical reduction of methylene blue using flow-injection analysis. The carrier stream was 12.7 μgml?1 methylene blue in phthalate-HCl buffer solution at pH 3.2. The reactor was irradiated with a 500-Watt halogen lamp to facilitate the development of the photochemical reaction. The system allows determination of ascorbic acid in the range 0.18–6.12 μgml?1 with relative standard deviations of 2.09 and 0.31% for 1.97 and 4.92 μgml?1 samples, respectively, and a sampling frequency of 50–55 h?1. The proposed method was applied successfully to the determination of ascorbic acid in vitamin C tablets.  相似文献   

3.
《Analytical letters》2012,45(8):1413-1427
Abstract

A flow-injection configuration for the spectrophotometric determination of oxalate, citrate and tartrate is proposed. The procedure is based on the photochemical decomposition of the complexes formed between iron(III) and these anions. The iron(II) produced in the photochemical reactions was detected by measuring the absorbance after complexation with ferrozine (λmax=562 nm). Linear calibration graphs were obtained over the concentration ranges 5.0 × 10?6 - 1.0 × 10?4 M, 8 × 10?6 - 1.8 × 10?4 M and 1.0 × 10?6 - 2 × 10?5 M for oxalate, citrate and tartrate, respectively. The relative standard deviations at the 1x10?5 M concentration level were within the range 1.29 - 1.47 %. The sampling frequency was about 40 samples h?1. The usefulness of the method was tested in the determination of oxalate in urine and spinach, of citrate in pharmaceuticals and soft drinks and of tartrate in pharmaceuticals. For the determination of oxalate in urine samples a prior separation of the analyte by precipitation with calcium chloride is recommended.  相似文献   

4.
A kinetic spectrophotometric method has been described for the determination of metoprolol tartrate in commercial dosage forms. The procedure is based on the reaction of the drug with 1‐chloro‐2, 4‐dinitrobenzene (CDNB) in dimethylsulfoxide (DMSO) at 100 ± 1 °C. The reaction is investigated by measuring the change in absorbance with time at 420 nm. Fixed‐time (ΔA) and equilibrium methods are chosen for obtaining the calibration curves. Both calibration curves were found to be linear over the concentration range of 5‐60 μg mL?1. The regression analysis of calibration data resulted in the linear regression equations of ΔA = ?1.608 × 10?4 + 3.96 × 10?3 C and A = 7.31 × 10?4 + 1.90 × 10?2 C for fixed time (ΔA) and equilibrium methods, respectively. The limit of detection (LOD) for fixed time and equilibrium methods are 1.16 and 0.415 μg mL?1, respectively. The method has been successfully applied to the quantitation of metoprolol tartrate in commercial dosage forms. Statistical comparison of the results shows that there is no significant difference between the proposed methods and El‐Ries's spectrophotometric method.  相似文献   

5.
《Analytical letters》2012,45(10):1667-1678
Abstract

A new spectrophotoraetric method has been developed for the analysis of pheniramine maleate and chlorphenlramine maleste, based on their reaction with iron (III). Pheniramine maleate and ch lor pheniramine maleate were found to form a 2:1 complex with iron (III) with an average log. stability constant of 12.26 and 12.36, respectively. The iron (III) complexes of both drugs showed maximum absorption at 273 nm, at pH 5, with slopes equal to 0.710 and 0.898 for pheniramine maleate complex and chlorpheniramine maleate complex, respectively. The proposed method was used for the determination of pheniramine maleate and chlorpheniramine maleate in quantities ranging between 0.25 × 10?4 M to 2.5 × 10?4 M with mean percentage recoveries of 100.17 ± 1.09% and 100.00 ± 1.13% for both drugs, respectively. The results obtained were compared with that of the B.P. (1980) method.  相似文献   

6.
A flow-injection chemiluminescence (CL) method for the determination of melatonin based on the CL reaction of melatonin with hydrogen peroxide and sodium hypochlorite (NaOCl) in a basic alkaline solution was developed. The possible CL mechanism has been discussed, and a proposal for the reaction pathway was given that singlet oxygen was clarified to be produced in this reaction system and was responsible for the CL emission. Under the optimized conditions, the linear concentration range of application was 1.0×10^-7-2.5 × 10^-4 moloL-I with a de- tection limit of 5.0 ×10^-8 moloL-1 (S/N= 3). The relative standard deviation for eight repeated measurements of 1.0×10^-6 mol·L^-1 melatonin was 2.8%. The interferences of several important biological substances, some indole compound, cations and anions were studied. No interference was found for the anions, glucose, starch, most of cations and low concentration (less than 3.0 × 10^-6 mol·L^-1) of some biological substances and indole compound. The method was applied to the determination of melatonin in rat pineal gland and drug with satisfactory results. The sample throughput was 90 injections per hour.  相似文献   

7.
Several 8-quinolinol silica gel (QSG) columns were used, with metal-uptake capacities of 10–156 μmol g?1. Various transition and heavy metal ions were used as analytes in nitrate, sulfate, phosphate, citrate, tartrate, oxalate, phthalate, and maleate mobile phases. Metal-ion retention increased with column capacity and pH. Optimum capacity factors were obtained on columns of intermediate capacity (27 and 46 μmol g?1). Retention times decreased with an increase in eluent buffer concentration, typically by half with a doubling of buffer. Evidence is presented for the occurence of mobile-phase complexation of analyte ions by eluent buffer species. Multiple or split peaks were often observed when the analyte solvent differed from the mobile phase. Chromatographic separation of up to six metals on the QSG columns is demonstrated in tartrate and maleate mobile phases.  相似文献   

8.
《Analytical letters》2012,45(5):973-983
Abstract

A rapid and sensitive flow‐injection chemiluminescence (FI‐CL) method, which is based on the CL intensity that generated from the redox reaction of Ce(IV)‐rhodamine B in H2SO4 medium, for the determination of acyclovir and gancyclovir is described. For acyclovir, the determination range is 3×10?8 g mL?1–7×10?5 g mL?1, with 1.56×10?8 g mL?1 as its determination limit. During 11 repeated measurements for 1×10?6 g mL?1 acyclovir, the relative standard deviation was 2.08%. For gancyclovir, the determination range was 5×10?8 g mL?1–7×10?5 g mL?1, with 2.35×10?8 g mL?1 as its determination limit. The relative standard deviation is 2.83% with 11 repeated measurements of 1×10?6 g mL?1 gancyclovir. This method can be successfully used to determine the content of acyclovir and gancyclovir in injections, acyclovir in eye drops, and, maybe, also for other ciclovirs.  相似文献   

9.
The present work describes the individual, selective and simultaneous quantification of acetaminophen (ACP) and tramadol hydrochloride (TRA) using a modification‐free boron‐doped diamond (BDD) electrode. Cyclic voltammetric measurements revealed that the profile of the binary mixtures of ACP and TRA were manifested by two irreversible oxidation peaks at about +1.04 V (for ACP) and +1.61 V (for TRA) in Britton‐Robinson (BR) buffer pH 3.0. TRA oxidation peak was significantly improved in the presence of anionic surfactant, sodium dodecyl sulfate (SDS), while ACP signal did not change. By employing square‐wave stripping mode in BR buffer pH 3.0 containing 8×10?4 mol L?1 SDS after 30 s accumulation under open‐circuit voltage, the BDD electrode could be used for quantification of ACP and TRA simultaneously in the ranges 1.0–70 μg mL?1 (6.6×10?6–4.6×10?4 mol L?1) and 1.0–70 μg mL?1 (3.3×10?6–2.3×10?4 mol L?1), with detection limits of 0.11 μg mL?1 (7.3×10?7 mol L?1) and 0.13 μg mL?1 (4.3×10?7 mol L?1), respectively. The practical applicability of the proposed approach was tested for the individual and simultaneous quantification of ACP and/or TRA in the pharmaceutical dosage forms.  相似文献   

10.
ABSTRACT

In the present study, a simple, cheap and sensitive electrochemical method based on a cathodically pretreated boron-doped diamond (CPT-BDD) electrode is described for the detection of triclosan with the cationic surfactant (cetyltrimethylammonium bromide, CTAB) media. The oxidation of triclosan was irreversible and exhibited an adsorption controlled process. The sensitivity of the adsorptive stripping voltammetric measurements was significantly improved with addition of CTAB. Using square-wave stripping mode, a linear response was obtained for triclosan determination in Britton-Robinson buffer solution at pH 9.0 containing 2.5 × 10?4 M CTAB at around + 0.67 V (vs. Ag/AgCl) (after 30 s accumulation at open-circuit condition). The method could be used in the range of 0.01–1.0 μg mL?1 (3.5 × 10?8–3.5 × 10?6 M), with a detection limit of 0.0023 μg mL?1 (7.9 × 10?9 M). The feasibility of the proposed method for the determination of triclosan in water samples was checked in spiked tap water.  相似文献   

11.
《Analytical letters》2012,45(4):675-682
Abstract

Enantioselective, potentiometric membrane electrodes (EPMEs) based on antibiotics are proposed for the enantioanalysis of L‐vesamicol. A carbon paste was modified with antibiotics (vancomycin, teicoplanin, and teicoplanin modified with acetonitrile), as chiral selectors. The EPMEs based on antibiotics were reliably used for enantiopurity tests of L‐vesamicol using the direct potentiometric technique. The following linear concentration ranges: 1.0×10?6–1.0×10?4, 1.0×10?6–1×10?3 and 1×10?7?1×10?2 mol/L; and detection limits: 1.1×10?7, 9.6×10?8, and 3.6×10?8 mol/L were determine for vancomycin, teicoplanin, and teicoplanin modified with acetonitrile–based EPMEs, respectively. The proposed EPMEs were applied for the enantioanalysis of L‐vesamicol in urine samples.  相似文献   

12.
A cobalt oxide nanoparticles (Co3O4NPs) and multi walled carbon nanotubes (MWCNTs) modified carbon paste electrodes were used to study the electrochemical behavior of linagliptin and empagliflozin in Britton Robinson buffer solution of pH 8.0 using cyclic and square wave voltammetry. The above mentioned modified electrodes showed highly sensitive sensing and gave an excellent anodic response for both drugs. The peak current varied linearly over the concentration ranges: 3.98×10?5–1.53×10?3 mol L?1 (18.82–723.00 μg/mL) and 7.94×10?6–1.07×10?4 mol L?1 (3.65–48.25 μg/mL) with determination coefficients of 0.9999 and 0.9998 for linagliptin and empagliflozin, respectively. The recoveries and relative standard deviations were found in the following ranges: 98.80 %–102.00 % and 0.23 %–1.90 % for linagliptin and 98.30 %–101.80 % and 0.11 %–1.86 % for empagliflozin. The detection and quantification limits were 1.13×10?5 and 3.76×10?5 mol L?1 (5.34and17.77 μg/mL) for linagliptin, 1.71×10?6and 5.68×10?6 mol L?1 (0.77 and 2.56 μg/mL) for empagliflozin. The proposed sensors have been successfully applied for the determination of the drugs in bulk, pharmaceutical formulations and biological fluids.  相似文献   

13.
《Analytical letters》2012,45(5):333-345
Abstract

The results of a complete study of 8 substrates for acid and alkaline phosphatase indicated 7-hydroxycoumarin (umbelliferone) phosphate to be the best substrate for the analysis of these enzymes. Using this ester, from 10?6 to 2 × 10?2 units per ml. of alkaline phosphatase and 10?5 to 0.06 units per ml. of acid phosphatase can be determined with an accuracy and precision of about 1.5%. Samples of serum as small as 1 μ;1. can be assayed. Analysis is performed by a direct initial reaction rate method in 2–3 minutes.  相似文献   

14.
《Analytical letters》2012,45(14):2537-2548
Abstract

Chemiluminescence (CL) was achieved by oxidation of sulphide with cerium(IV) in the presence of cinchona alkaloids (quinine, quinidine or cinchonine). The CL intensity was correlated with the concentration of each cinchona alkaloid. Based on this phenomenon, sensitive CL methods for these alkaloids were described. Quinine (4×10?8~1×10?4 g/ml), quinidine (1×10?7 ~ 1×10?3 g/ml) and cinchonine (1×10?6 ~ 8×10?4 g/ml) could be determined with detection limits of 1×10?8 g/ml, 4×10?8 g/ml and 6×10?7 g/ml, respectively.  相似文献   

15.
《Analytical letters》2012,45(16):2607-2619
Abstract

This article describes the quantitative determination of Cu(II) using thermal lens spectrometry. The chromogenic reaction involving Cu(II) and 5-(4-sulphophenylazo)-8-aminoquinoline in alkaline solution was studied in different experimental conditions such as pH, ligand concentration, methanol volume, and presence of interfering ions. A collinear dual beam set-up has been used for direct quantitation in water samples without a pre-concentration step. The optimized conditions provided a linear calibration in the concentration range from 3.0 to 15.0?×?10?7?mol L?1. The detection and quantitation limits were 6.13?×?10?8? and 2.04?×?10?7?mol L?1, respectively. Resultantly, an application to Cu(II) determination in tap water (recovery 99.8–103.3%) and mining (synthetic) wastewater (95.3–98.0%) shows relative SDs ≤ 3.1%. The method is presented as a new alternative for the direct Cu(II) determination in real samples.  相似文献   

16.
《Analytical letters》2012,45(13):2175-2187
Abstract

Benzoyl peroxide (BP) was determined by differential pulse voltammetry (DPV) using a glassy carbon electrode in a dichloromethane‐acetic acid (1.5×10?2 mol l?1) solution and tetrabutyl ammonium perchlorate (0.01 mol l?1) as the supporting electrolyte. The peak potential was ?0.045 V (vs. Ag/AgCl). There was a good linear relationship between the peak current and the benzoyl peroxide concentration in the range of 2.5×10?6–1.0×10?4 mol l?1. The detection limit of the method was 2.5×10?7 mol l?1. The recovery was 94.8–106.0%. The samples of wheat flour and the pharmaceutical preparations for the treatment of acne vulgaris were directly detected with desired results. The reaction mechanism of benzoyl peroxide on the electrode was also discussed, which was two electrons and two protons irreversible reaction.  相似文献   

17.
ABSTRACT

A simple, highly sensitive voltammetric method for the determination of urapidil at poly(sodium4-styrenesulfonate) functionalized graphene-modified electrode (PSS-Gr/GCE) was described. Based on the PSS-Gr composites-modified glassy carbon electrode as a simple voltammetric sensor, it exhibited good conductivity and high sensitivity to urapidil. Under the optimize condition, a good linear relationship was obtained between peak currents and urapidil concentrations in the wider range of 2.0 × 10?9–8.0 × 10?8 mol L?1 and 2.0 × 10?7–2.0 × 10?5 mol L?1 with detection limit of 8 × 10?10 mol L?1 (S/N = 3). Based on the high sensitivity and good selectivity of the proposed electrode, the proposed method could apply to the detect of urapidil in urapidil sustained release tablets with satisfactory results.  相似文献   

18.
《Analytical letters》2012,45(7):1337-1348
Abstract

A colorimetric method for the determination of ampicillin (Amp.) and 6-aminopenicillanic acid (6-APA) are described, based on the reaction of these drugs with acenaphthenequinone in basic media to give a highly intense red coloured product. The latter exhibits an absorption maximum at 610 nm with apparent molar absorptivities of 2.83 and 1.45 × 104 l. mol?1 cm?1 and Sandell sensitivities of 0.013 and 0.015 μg cm?2 for Amp. and 6-APA, respectively. The optimum concentration ranges are 0.4-10 and 0.4-14 μg ml?1 for Amp. and 6-APA, respectively. For more accurate results, Ringbom optimum concentration ranges are 1–8.5 and 1–12 μg ml?1 for Amp. and 6-APA, respectively. Statistical analysis indicated that there was no significant difference between the results obtained by the described method and those of the official methods. The mean recoveries percentage were found to be 99.5 × 1.1% for pharmaceutical formulations and 99.1 × 1.6% for serum and urine samples. The method is selective for the determination of Amp. or 6-APA in the presence of their degradation products, additives and excipiences that are normally encountered in dosage forms. The proposed method was applied successfully to the determination of Amp. in pharmaceutical formulations. Also, applicability of the proposed method to human serum and urine is presented and the validity assessed by applying the standard addition technique.  相似文献   

19.
The effects of organic solvent, time and temperature on the colour-forming reaction are described. For nine solvents tested, the molar absorptivities were in the range 2.0×104?6.7×104 mol?1 cm?1; best sensitivity was obtained with a 1:1 water/2-propanol solution after a standing time of 35 min; temperature should be controlled to ±2°C. Beer's law was obeyed for 0–1.45 μg ml?1 Mn(II). The improved method was applied to determinations of manganese(II) in various herbs and chemical reagents; the values found were in the range 5.4–48.4 μg g?1 in herbs, and 0.001-0.012% (w/w) in reagents.  相似文献   

20.
《Analytical letters》2012,45(15):1865-1886
Abstract

A new and sensitive spectrophotometric method has been developed for the determination of tetracyclines either in a pure form or in Pharmaceuticals, by a molybdenum blue method. The procedure is based on the observation that, in sulphuric acid medium, tetracyclines reduce ammonium molybdate to molybdenum blue, the absorbance of which is proportional to the amount of antibiotic present. The variables affecting development of the color have been investigated and the conditions optimized. Beer's law is obeyed for up to 20 μg/ml of tetracycline HCl and oxytetracycline HCl, 28 μg/ml of demeclocycline HCl, 18 μg/ml of chlortetracycline HCl, 32 μg/ml of doxycycline HCl and 40 μ/ml of rolitetracycline. Molar absorptivities (1 mol?1 cm?1) and Sandell's sensitivities (μ cm?2 per 0.001 absorbance unit) are, respectively: tetracycline HCl 4.9×104 and 0.0098, oxytetracycline HCl 5.4×104 and 0.0092, demeclocycline HCl 1.6×104 and 0.0313, chlortetracycline HCl 5.5×104 and 0.0094, doxycycline HCl 3.4×104 and 0.0141, rolitetracycline 2.7×104 and 0.0195.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号