Simultaneous extraction and determination of sulfadiazine and sulfamethoxazole in water samples and aquaculture products using [Bmim]BF4/(NH4)3C6H5O7 aqueous two-phase system coupled with HPLC

An ionic liquid aqueous two-phase system (ILATPS) of 1-butyl-3-methylimidazolium tetrafluoroborate ([Bmim]BF₄)/ammonium citrate ((NH₄)₃C₆H₅O₇) coupled with high-performance liquid chromatography was developed for the separation and determination of sulfadiazine (SD) and sulfamethoxazole (SMX) in water samples as well as aquaculture products. The effect of such parameters as the types and concentrations of salts, temperature, the concentrations of SD and SMX and the extraction time on the partitioning behavior expressed in terms of extraction efficiency has been evaluated. Under the optimal conditions, this extraction method has been successfully applied to the analysis of SD and SMX in water samples and aquaculture products with the recoveries of 98.29–99.55 % (SD) and 92.09–99.82 % (SMX). The detection limits for two analytes were 0.9 ng mL^?1 (SD) and 1.8 ng mL^?1 (SMX). In comparison with the traditional solvent extraction, ILATPS is much simpler and more environmentally friendly for the separation and enrichment of the sulfonamides antibiotics.     

Determination of Pantoprazole, Rabeprazole, Esomeprazole, Domperidone and Itopride in Pharmaceutical Products by Reversed Phase Liquid Chromatography Using Single Mobile Phase

A simple, sensitive, and precise high performance liquid chromatographic method for the analysis of pantoprazole, rabeprazole, esomeprazole, domperidone and itopride, with ultraviolet detection at 210 nm, has been developed, validated, and used for the determination of compounds in commercial pharmaceutical products. The compounds were well separated on a Hypersil BDS C18 reversed-phase column by use of a mobile phase consisting of 0.05 M, 4.70 pH, potassium dihydrogen phosphate buffer - acetonitrile (720:280 v/v) at a flow rate of 1.0 mL min^?1. The linearity ranges were 400–4,000 ng mL^?1 for pantoprazole, 200–2,000 ng mL^?1 for rabeprazole, 400–4,000 ng mL^?1 for esomeprazole, 300–3,000 ng mL^?1 for domperidone and 500–5,000 ng mL^?1 for itopride. Limits of detection (LOD) obtained were: pantoprazole 147.51 ng mL^?1, rabeprazole 65.65 ng mL^?1, esomeprazole 131.27 ng mL^?1, domperidone 98.33 ng mL^?1 and itopride 162.35 ng mL^?1. The study showed that reversed-phase liquid chromatography is sensitive and selective for the determination of pantoprazole, rabeprazole, esomeprazole, domperidone and itopride using single mobile phase.     

Quantification of Thiram in Honeybees: Development of a Chemiluminescent ELISA

Abstract

A Chemiluminescence Enzyme‐Linked Immuno‐Sorbent Assay (CL‐ELISA) for determination and quantification of the fungicide thiram in honeybees was developed in an indirect competitive format. The assay was optimized by determining: the optimal coating conjugate concentration and anti‐thiram antiserum dilution, the effect of the incubation time on the competitive step, the tolerance to organic solvents. The IC₅₀ and the limit of detection (LOD) values were 60 ng mL^?1 and 9 ng mL^?1, respectively, similar to those of colorimetric ELISA with a calibration range of 9–15,000 ng mL^?1. Cross reactivity of some related compounds such as some dithiocarbamates, a thiocarbamate, the ethylenethiourea and the tetramethylthiourea were tested. The assay was then applied to honeybees sample extracts obtained by using the liquid‐liquid extraction or the graphitized carbon‐based solid phase extraction.

The calibration curves in honeybee extracts from liquid‐liquid procedure gave an IC₅₀ of 141 ng mL^?1 and a LOD of 17 ng mL^?1. In case of extracts obtained by SPE these values were 139 ng mL^?1 and 15 ng mL^?1, respectively. The average recovery value from honeybee extracts spiked with 75 ng mL^?1 of thiram was 72% for SPE, higher than for liquid‐liquid extraction (60%). On the opposite, when the honeybees were directly spiked with 2 and 10 ppm the average recovery was higher for liquid‐liquid extraction (54%), than for SPE (31%). Finally, the assay was applied to honeybee samples collected during monitoring activities in Italy and Russia.     

Quantification of Imidacloprid in Honeybees: Development of a Chemiluminescent ELISA

A Chemiluminescent Enzyme-Linked Immuno-Sorbent Assay (CL-ELISA) for determination and quantification of the fungicide imidacloprid in honeybees was developed in an indirect competitive format. The assay was optimized by determining: the optimal coating conjugate concentration and anti-imidacloprid antiserum dilution, the effect of the incubation time on the competitive step, and the tolerance to organic solvents. The IC₅₀ and the limit of detection (LOD) values were 14.8 ng mL^?1 and 0.11 ng mL^?1, respectively, similar to those of colorimetric ELISA with a calibration range of 0.1–2600 ng mL^?1. Cross reactivity of some related compounds such as three imidacloprid metabolites, 6-chloro nicotinic acid, 5-hydroxy-imidacloprid, and imidacloprid olefin, and one other chloronicotinoid insecticide, acetamiprid, were tested. The assay was then applied to honeybee extracts obtained by using the liquid-liquid extraction. The calibration curves in honeybee extracts from the liquid-liquid procedure gave an IC₅₀ of 23.7 ng mL^?1 and a LOD 1.6 ng mL^?1. The average recovery value from honeybee extracts spiked with 100 and 1000 ng mL^?1 of imidacloprid were 73% and 76%, respectively. Finally, the assay was applied to honeybee samples collected during monitoring activities in Italy; it was found that only five of the 27 samples were positives, with low concentrations of imidacloprid ranging between 1.2 and 15.4 ng g^?1.     

An Experimental Design Approach to Selecting the Optimum LC Conditions for the Determination of Local Anaesthetics

A sensitive high performance liquid chromatographic (HPLC) method has been developed and validated for the simultaneous determination of four local anaesthetics: lidocaine, proparacaine, bupivacaine and oxybuprocaine. A full factorial design was used. The chromatographic separation was achieved using a Bondesil C₈ (4.6 × 2.5 mm i.d., particle size 5 μm) analytical column. An optimised mobile phase consisted of acetonitrile and sodium dihydrogen phosphate (pH = 3.0, 20 mM) (30:70, v/v) at a flow rate of 1.2 mL min^?1. Local anaesthetics detection was performed by UV-Vis detector at 220 nm. The retention times for lidocaine, proparacaine, bupivacaine and oxybuprocaine were 5.74, 9.28, 16.84 and 26.26 min, respectively. HPLC-UV-Vis method was linear in the range of 50–5,000 ng mL^?1 for lidocaine and proparacaine and 100–5,000 ng mL^?1 for bupivacaine and oxybuprocaine. The limit of detection (LOD) was 25 ng mL^?1 for lidocaine, proparacaine and 30 ng mL^?1 for bupivacaine and oxybuprocaine. The limit of quantification (LOQ) was found to be 50 ng mL^?1 for lidocaine, proparacaine and 100 ng mL^?1 for bupivacaine, oxybuprocaine. In intra-day and inter-day precision and accuracy analysis, the relative standard deviation was found to be less than 8%.     

Development of Immunoaffinity Sample-Purification for GC–MS Analysis of Ractopamine in Swine Tissue

A method combining immunoaffinity chromatography with gas chromatography–mass spectrometry (GC–MS) has been established for determination of ractopamine residues in swine liver and urine. After clean-up on an immunoaffinity chromatography column, GC–MS analysis revealed recovery from blank swine liver and urine fortified at 2.5–20 ng g^?1 (ng mL^?1 for urine), respectively, was 68.2–78.6 and 76.2–83.1%. The limits of detection and quantification were 0.5 ng g^?1 (or ng mL^?1) and 2.0 ng g^?1 (or ng mL^?1), respectively. The procedure was used for analysis of ractopamine residues in samples of swine liver and urine in which the levels were unknown. The amounts detected were 9–216 ng g^?1 (ng mL^?1).     

Simultaneous Determination of Amoxicillin and Clavulanic Acid in Dog Plasma by High-Performance Liquid Chromatography Tandem Mass Spectrometry

A rapid, sensitive, and specific high-performance liquid chromatography tandem mass spectrometric method was developed for the simultaneous determination and confirmation of amoxicillin and clavulanic acid in plasma. Plasma sample was subjected to a simple deproteinization with acetonitrile, and then the supernatant was directly diluted by water. Analysis was performed on a Phenomenex Luna C₈ reversed-phase column by detection with mass spectrometry in negative ions multiple reaction monitoring mode. A gradient elution program with 0.1% formic acid and acetonitrile was performed at a flow of 0.25 mL min^?1. There is good linearity in the range of 0.5–500 ng mL^?1 for both amoxicillin and clavulanic acid. The decision limits of amoxicillin and clavulanic acid were 0.06 ng mL^?1 and 0.08 ng mL^?1 in plasma, respectively, and the detection capabilities of two analytes were below 0.5 ng mL^?1. Acceptable precision and accuracy were obtained for concentrations over the standard curve range. The extraction recoveries of amoxicillin and clavulanic acid were between 102% and 115% in plasma at three spiked levels of 0.5, 50, and 500 ng mL^?1, with the relative standard deviations less than 15% for each analyte. The developed method was applied to pharmacokinetic studies of amoxicillin and clavulanic acid tablets in healthy beagles.     

Development of a Sensitive LC Assay with Fluorescence Detection for the Determination of Zearalenone in Rat Serum

A simple and sensitive liquid chromatographic assay with fluorescence detection assay was developed for the determination of zearalenone levels in rat serum. The assay utilized a single liquid–liquid extraction with t-butyl methyl ether and isocratic elution using a mobile phase consisting of acetonitrile and 0.1% triethylamine in distilled water (pH = 6) (50:50, v/v). Linearity was observed over a concentration range from 10 to 1,000 ng mL^?1 (r = 0.9995), with the limit of quantification at 10 ng mL^?1 with 100 μL of rat serum. The validated assay was applied to a pharmacokinetic study in rats.     

Micro-solid phase extraction of ochratoxin A, and its determination in urine using capillary electrophoresis

We describe a simple, environmentally friendly and selective technique for the determination of ochratoxin A (OTA) in urine. It involves (a) the use of a molecularly imprinted polymer as a sorbent in micro-solid-phase extraction in which the sorbent is contained in a propylene membrane envelope, and (b) separation and detection by capillary electrophoresis (CE). Under optimized conditions, response is linear in the range between 50 and 300 ng mL^?1 (with a correlation coefficient of 0.9989), relative standard deviations range from 4 to 8 %, the detection limit for OTA in urine is 11.2 ng mL^?1 (with a quantification limits of 32.5 ng mL^?1) which is lower than those of previously reported methods for solid-phase extraction combined with CE. The recoveries of OTA from urine spiked at levels of 50, 150 and 300 ng mL^?1 ranged from 93 to 97 %.

A novel chemiluminescence reaction system for the determination of lincomycin with diperiodatonickelate(IV)

A sensitive and high selective chemiluminescence (CL) method was developed for the determination of lincomycin in acid medium using diperiodatonickelate as a reagent. The mechanism leading to luminescence is discussed by comparing the spectra of fluorescence and CL. Relative CL intensity is linear in the range from 8.0 ng mL^?1 to 1.0 µg mL^?1, the limit of detection is 2.5 ng mL^?1 (3σ), and the relative standard deviation is 4.0% at 0.1 µg mL^?1 of lincomycin (n?=?7). The method was successfully applied to the determination of lincomycin in injections, human urine, and in serum samples.     

Cyanopropyl Bonded-Phase Cartridges for Trace Enrichment of Dioxins and Chlorinated Pesticides from Water Samples

Gas chromatography of dioxins and chlorinated pesticides in water samples has been performed after adsorption from 50 to 100 mL sample on to a cartridge containing 100 mg cyanopropyl-bonded porous silica. The dioxins and chlorinated pesticides were desorbed with 2 mL carbon disulfide, which is concentrated and analysed by gas chromatography coupled with an electron-capture detector. The average recovery of 0.20 ng mL^?1 of each chlorinated pesticide and of 0.50 ng mL^?1 of each dioxin from distilled water and river water samples (50 mL) is ≥97.2% with a standard deviation (SD) ≤ 2.6. In the dioxin separation from chlorinated pesticides the recovery of dioxins at levels of 0.1–0.5 ng mL^?1 is ≥97.9% with a SD ≤ 1.3, with traces of aldrin, heptachlorepoxide and 4,4′-DDD (≤1.7%) by the CN-Sep-Pak cartridge, while the recovery of chlorinated pesticides at levels of 0.05–0.2 ng mL^?1 is ≥97.4% with a SD ≤ 1.5, with traces of hep-dioxin (2.4%) and penta-dioxin (1.0%) by the C₁₈-Sep-Pak cartridge connected “in series” to the CN-Sep-Pak cartridge.     

Optimization of Continuous Flow Hydride Generation Inductively Coupled Plasma Optical Emission Spectrometry for Sensitivity Improvement of Bismuth

Experimental variables in continuous flow hydride generation inductively coupled plasma-optical emission spectrometry (CF-HG-ICP-OES) were optimized for determination of bismuth. Concentrations of NaBH₄, HCl, and NaOH, flow rates of NaBH₄, sample solution, waste and carrier argon, radio frequency power, lengths of reaction, and stripping coils were optimized to obtain lower detection limits. Under optimum conditions, the detection limit was calculated as 0.16 ng mL^?1, and the calibration plot was linear between 1.0–50.0 ng mL^?1. An improvement in detection limit of 5.75 times by CF-HG-ICP-OES was reached vs. ICP-OES. Relative standard deviation (RSD) for ten replicate measurements of 10.0 ng mL^?1 Bi was calculated as 3.9%. Effect of possible interferic ions on Bi signal was evaluated. Accuracy of method was verified by using a standard reference material, SRM 1643e. Results found for Bi were in satisfactory agreement with certified values. The proposed method was then employed to determine trace concentration of Bi in milk samples. Bi amounts in samples were found in the range from lower than the quantitation limit to 14.5 ng mL^?1, whereas Bi concentrations were lower than the detection limit in three samples.     

Colorimetric Determination of Lead Using Gold Nanoparticles

A combined homogeneous assay and colorimetric determination method using gold nanoparticles was developed for rapid determination of lead(II) in contaminated natural waters. The presence of lead(II) in the colloidal gold suspension causes a change in the absorbance of the suspension. An increase in the absorption property at 595 nm is accompanied by a change in the size of the gold nanoparticles. High concentrations of lead cause aggregation of the gold colloids. Colloidal gold nanoparticles were synthesized using tannic acid as the reducing agent; this reagent allowed selective determination of lead in 10 µL of water, with a detection limit of 310 ng mL^?1 with an analysis time of 5 min. The coefficient of variation for lead(II) within the working range of the assay (520 ng mL^?1–13 µg mL^?1) varied from 1.3% to 9.2%. The limit of detection using this method with a sample volume of 50 µL was 60 ng mL^?1. The coefficient of variation for lead over the working range of the determined concentrations (80 ng mL^?1–25 µg mL^?1) varied from 0.2% to 9.3%, while the values for the inter-day assay (n = 8) were less than 10%. The method was employed for the analysis of river, lake, marsh, and spring water; the recovery of lead was determined to be 72.5%–130% for 10 µL of water and 93.6%–114.7% for 50 µL.     

Catalytic Square-Wave Voltammetric Determination of Acrylamide in Potato Chips

Abstract

Square-wave voltammetry is a fast technique used for determination of trace amounts of acrylamide. When cobalt(II) ions were added to the acrylamide solution, a catalytic peak at about ?1.35 V vs. Ag/AgCl was observed, which was proportional to acrylamide concentration. The calibration curve showed good linearity in the range of 200–800 ng mL^?1 of acrylamide with a regression coefficient of 0.9989. The limit of detection of the method was 3.52 ng mL^?1, and the relative standard deviations for concentrations of 300 ng mL^?1 and 700 ng mL^?1 were 99.8% × 10^?2 and 79.7% × 10^?2, respectively.     

Sandwich Immunoassay for Hepatitis C Virus Non-Structural 5A Protein Using a Glassy Carbon Electrode Modified with an Au-MoO3/Chitosan Nanocomposite

A novel electrochemical immunosensor was prepared for the detection of the hepatitis C virus non-structural 5A protein. A glassy carbon electrode was modified with an Au-MoO₃/Chitosan nanocomposite that warranted good conductivity and biocompatibility. Mesoporous silica with a large specific surface served as a nanocarrier for horseradish peroxidase and the polyclonal antibody as the reporter probe. The immunosensor was characterized by scanning electron microscopy, electrochemical impedance spectroscopy, and cyclic voltammetry. Following the sandwich-type immunoreaction, horseradish peroxidase was efficiently captured on the surface of the electrode to catalyze the decomposition of hydrogen peroxide. The analytical signal was obtained as an amperometric i-t curve (chronoamperometry). The assay reported here had a wide detection range (1 ng mL^?1 ?50 µg mL^?1) and detection limit as low as 1 ng mL^?1 of hepatitis C virus non-structural 5A protein. The electrochemical biosensor experiments showed excellent reproducibility, high selectivity, and outstanding stability for the determination of hepatitis C virus non-structural 5A protein, and it was successfully applied to the detection of the analyte in real serum samples.     

Simultaneous Determination of Pregabalin, Sildenafil and Its Active Metabolite in Rat Plasma Utilising SPE Followed by LC�CMS�CMS

A sensitive and selective analytical method for the quantification of pregabalin, sildenafil and the active desmethyl metabolite of sildenafil (UK-103320) has been developed. The method can simultaneously quantify the three analytes within the expected in vivo concentration ranges using 50 ??L of rat plasma. It utilises solid-phase extraction followed by high performance liquid chromatography coupled with tandem mass spectrometry. Quantitation in rat plasma demonstrated good accuracy and precision over the following dynamic ranges for each analyte: pregabalin (70?C10,000 ng mL^?1), sildenafil (1?C2,000 ng mL^?1) and UK-103320 (1?C2,000 ng mL^?1). For each analyte, the following lower limits of quantitation were obtained: 70 ng mL^?1 for pregabalin and 1 ng mL^?1 for sildenafil and UK-103320, respectively. The method was successfully used to analyse plasma samples from rats when pregabalin and sildenafil were administered in combination.     

Surfactant-assisted dispersive liquid–liquid micro-extraction combined with magnetic solid-phase extraction for analysis of polyphenols in tobacco samples

A novel and simple two-step micro-extraction technique combining surfactant-assisted dispersive liquid–liquid micro-extraction and magnetic solid-phase extraction prior to high-performance liquid chromatography was established for analysis of polyphenols including chlorogenic acid, caffeic acid, and scopoletin in tobacco samples. In the developed system, Fe₃O₄ nanoparticles were synthesized by a one-step chemical co-precipitation method and used to remove hydrophobic substances in tobacco samples by physical adsorption. Low-density solvent (1-heptanol) and cationic surfactant cethyltrimethyl ammonium bromide were employed as extraction solvent and disperser agent, respectively. Under the optimized experimental conditions, a good linearity of the method was obtained over the concentration range from 0.1 to 1000 ng mL^?1 for target analytes. The limits of detection (S/N?=?3) were 0.05 ng mL^?1 for CGA, 0.10 ng mL^?1 for CFA, and 0.12 ng mL^?1 for SP, respectively. Finally, the applicability of the developed method was evaluated by extraction and determination of these three phenolic compounds in tobacco samples and satisfactory average recoveries of spiked samples were between 96.6 and 102.7%.     

Immunofluorescent Analysis with Magnetic Nanoparticles for Simultaneous Determination of Antibiotic Residues in Milk

An analytical system for simultaneous detection of three antibiotic residues in milk (penicillin, tetracycline, and sulfadimethoxine sodium salt) was developed. The method was based on a fluorescence immunoassay. Magnetic nanoparticles (MNPs) were prepared and then coated with 3-(aminopropyl) triethoxysilane (APTES). Antibodies, against penicillin, tetracycline, and sulfadimethoxine, were immobilized on APTES-MNPs. Two immobilization methods were used: a random and an oriented method by protein A. The fluorochrome-antigen conjugates, containing FITC, ATTO 590, and ATTO 630 were obtained. Three separate immunofluorescent analyses were investigated for penicillin, tetracycline, and sulfadimethoxine, first in buffer and then in milk. Linearity values of standard curves in milk were: for penicillin 4–15 ng mL^?1, for tetracycline 50–500 ng mL^?1 (using random immobilization) and 100–500 ng mL^?1(using oriented immobilization), and for sulfadimethoxine 100–500 ng mL^?1. The linearity and sensitivity of calibration curves of determination of penicillin, tetracycline and sulfadimethoxine in milk were very close to the obtained results for separate determination of three antibiotics. It was shown that the multiple immunofluorescence analysis for antibiotic residues in milk without preliminary treatment is effective and rapid.     

An Effective High-Performance Liquid Chromatographic–Mass Spectrometric Assay for Catecholamines, as the N(O,S)-Ethoxycarbonyl Ethyl Esters, in Human Urine

The purpose of this study was to develop a simple and accurate analytical method for determination of norepinephrine, epinephrine, and dopamine in urine. The method involves liquid–liquid extraction then liquid chromatography–mass spectrometry (LC–MS). Alkyl chloroformate derivatives were prepared, as the N(O,S)-alkoxycarbonyl alkyl esters of the analytes, in the aqueous samples. The optimum derivatizing reagent for preparation of the N(O,S)-alkoxycarbonyl alkyl esters was chosen by comparing the efficiency of LC of the derivatized analytes after liquid–liquid extraction. The optimum conditions for liquid–liquid extraction from the aqueous matrix were pH 3.0, no salt, and diethyl ether as extraction solvent. Limits of detection (LOD) were 0.5 ng mL^?1 for dopamine and epinephrine and 0.1 ng mL^?1 for norepinephrine. Limits of quantification (LOQ) for urine samples were 1.0 ng mL^?1 for all three compounds. The precision of intra- and inter-day assays was 1.65–581 and 7.17–9.73% (relative standard deviation, RSD), respectively. The range of inaccuracy for intra- and inter-day assays was ?6.47 to 11.9% and ?7.5 to 7.76% (bias) at concentrations of 5 and 50 ng mL^?1, respectively.     

Diphenyl diselenide grafted onto a Fe<Subscript>3</Subscript>O<Subscript>4</Subscript>-chitosan composite as a new nanosorbent for separation of metal ions by effervescent salt-assisted dispersive magnetic micro solid-phase extraction

Diphenyl diselenide was immobilized on chitosan loaded with magnetite (Fe₃O₄) nanoparticles to give an efficient and cost-effective nanosorbent for the preconcentration of Pb(II), Cd(II), Ni(II) and Cu(II) ions by using effervescent salt-assisted dispersive magnetic micro solid-phase extraction (EA-DM-μSPE). The metal ions were desorbed from the sorbent with 3M nitric acid and then quantified via microflame AAS. The main parameters affecting the extraction were optimized using a one-at-a-time method. Under optimum condition, the limits of detection, linear dynamic ranges, and relative standard deviations (for n?=?3) are as following: Pb(II): 2.0 ng·mL^?1; 6.3–900 ng·mL^?1; 1.5%. Cd(II): 0.15 ng·mL^?1; 0.7–85 ng·mL^?1, 3.2%; Ni(II): 1.6 ng·mL^?1,.6.0–600. ng·mL^?1, 4.1%; Cu(II): 1.2 ng·mL^?1, 3.0–300 ng·mL^?1, 2.2%. The nanosorbent can be reused at least 4 times.

Open image in new window

Graphical abstract Fe₃O₄-chitosan composite was modified with diphenyl diselenide as a sorbent for separation of metal ions by effervescent salt-assisted dispersive magnetic micro solid-phase extraction.