Determination of Trace Amounts of Palladium(II) by Solid-Phase Spectrophotometry

A simple and sensitive method for solid-phase spectrophotometric determination of palladium(II) at µgL^–1 level based on the reaction product of Pd²⁺ with disodium 1-nitroso-2-hydroxynaphthalene-3,6-disulphonate (Nitroso R salt) previously immobilized on Dowex 1×1 anion exchanger has been developed. The experimental factors (wavelength, pH, amount of resin, concentration of Pd²⁺ solution, volume of solution sample, equilibration time) were optimized. The advantages of this procedure as opposed to solution methods are discussed. The results obtained with synthetic solutions clearly indicate the suitability of the proposed method for real samples analysis.     

Spectrophotometric determination of palladium by solvent extraction as the Pd(II)-biacetylmonoxime 2-pyridylhydrazone complex

Determination of trace levels of palladium(II) is described. The method relies upon the extraction of palladium(II)-biacetylmonoxime 2-pyridylhydrazone (BMPH) from aqueous acidic solution into chloroform to form a purple-reddish complex. The molar absorptivity of the Pd-BMPH complex is about 7500 liters mol^?1 cm^?1 at 560 nm in the chloroform extract. The highly colored chloroform extract is suitable for spectrophotometric determination. The method devised has been applied to the determination of palladium in $\text{Pd}\text{CaCO}{}_3$ catalyst with good results.     

On-line determination of palladium by flame atomic absorption spectrometry coupled with a separation/preconcentration minicolumn containing a new sorbent

A method was developed for the on-line determination of palladium in complex matrices with flame atomic absorption spectrometry (FAAS) using Amberlite XAD-16 resin functionalized with 2-[2-(5-thiol-1,3,4-thiadiazolyl)]-azonaphthol (TTAN) reagent. Optimum experimental conditions such as pH of sample, type of eluent, amount of resin, volumes of sample and eluent solution, flow rates of sample and eluent, and effect of interfering ions were established. A 0.1?mol?L^?1 thiourea solution in 0.5?mol?L^?1 HCl was used as the eluent and subsequently transportation the analyte ions into the nebulizer–burner system for atomization. The synthesized chelating resin material showed excellent chemical and mechanical resistance, fast adsorption kinetics permitting the use of high sample flow rates without significant losses of retention efficiency. The detection limit of the method was 1.5?µg?L^?1 while the relative standard deviation (RSD%) was 2.4% at 0.1?mg?L^?1 Pd(II) level. The developed method was successfully applied to the determination of palladium in the catalytic converter and water samples.     

Isonitroso-4-Methyl-2-Pentanone for Solvent Extraction and Spectrophotometric Determination of Palladium (II) at Trace Level

Abstract

Isonitroso-4-methyl-2-pentanone (HIMP) is proposed as a new reagent for extraction and photometric determination of Pd(II). The reagent forms a yellow complex with palladium in the pH range 4.0-5.0. The complex extracted into chloroform was measured at 330 nm. The molar absorptivity was found to be 5.37 × 10³ 1 mol^?1 cm^?1 and Sandell's sensitivity 20 ng cm^?2 Beer's law was obeyed over the concentration range 0.1-10.0 μg/ml of palladium. The method is applicable for palladium estimation in Ores and catalysts.     

Simultaneous separation and extraction of Ag(I), Pb(II) and Pd(II) ions by solid phase method and determination of these ions by flame atomic absorption spectrometry

A simultaneous preconcentration and separation method for determination of trace amount of dissolved Ag⁺, Pb²⁺ and Pd²⁺ ions by modified octadecyl silica membrane disks with DBzDA18C6 was developed. The adsorbed metal complexes were eluted from disk with 10?mL of 4?M KCl and determined by flame atomic absorption spectroscopy. Several parameters such as anion effect, pH of sample solution, type of eluent, amount of ligand, sample and elution flow rate were evaluated. The effect of diverse ions on preconcentration was also investigated. A precocentration factor of 110 can easily be achieved depending on the volume of the sample. For 100?mL of the solution the linear dynamic rang were found to be 30–1000, 140–6000, 60–900?μg?l^?1 for Ag⁺, Pb²⁺ and Pd²⁺, respectively. Based on three standard deviation of the blank the detection limit was obtained as 1.8, 8.0 and 4.2?μg?L^?1 for Ag⁺, Pb²⁺, Pd²⁺, respectively. The formation constants of Ag⁺ and Pb²⁺ ions with DBzDA18C6 at 25?°C were determined from the molar conductance–mole ratio data. This method was applied for the determination of Ag⁺, Pb²⁺ and Pd²⁺ in environmental water, tea and soil samples.     

A highly selective and sensitive colorimetric chemosensor based on polyurethane foam impregnated with 3-methyl-2, 6-dimercapto-1,4-thiopyrone for on-site preconcentration and determination of palladium(II)

ABSTRACT

A new sorbent and chemosensor for highly selective and sensitive on-site preconcentration and colorimetric determination of Pd(II) was developed based on its reaction with 3-methyl-2,6-dimercapto-1,4-thiopyrone (MDT) immobilised onto polyurethane foam (PUF). Complexation of Pd(II) with MDT sorbed on PUF tablets leads to a contrast change in the sorbent colour from pale yellow to reddish-brown. The developed chemosensor is highly selective with respect to the transition and platinum group metals. It has a maximum sorption capacity of 17 µmol g^?1 for Pd(II). Reaction is possible in a strongly acidic medium (up to10 M HCl), and the properties of the chemosensor do not change during storage for a long time. The colorimetric response of the chemosensor was measured using red–green–blue (RGB) colour model. The dependence of the luminosity of the G channel on the Pd(II) concentration was linear in the concentration range from 0.3 to 64 µg L^?1 with a detection limit of 0.1 µg L^?1 (R² = 0.997). The colour scale for visual detection of Pd(II) was constructed in the concentration range of 0.02–0.64 mg L^?1 for the sorption from 20 mL of an aqueous sample. The accuracy of the developed methods was assessed by the analysis of a certified reference material (platinum–palladium alloy) and by comparison with the results of gravimetric or graphite furnace atomic absorption spectrometry (GFAAS) determination of Pd. The developed method was successfully applied to determine Pd in samples of mine water and road dust, in the electrolyte bath and in the sewage sludge of a palladium electroplating bath.     

Analysis of Sub-Microgram Levels of Palladium (II) in Environmental Samples by Selective Extraction and Spectrophotometric Determination with N-p-Methoxyphenyl-2-Furylacrylohydroxamic Acid and 5-(Diethylamino)-2-(2-Pyridylazo) Phenol

Abstract

Nine new hydroxamic acids in conjunction with four pyridylazo reagents were explored for extractive separation and spectrophotometric determination of palladium in environmental samples. It was found that maximum sensitivity and selectivity was achieved by employing N-p-methoxyphenyl-2-furylacrylohydroxamic acid (MFHA) and 5-(diethylamino)-2-(2-pyridylazo) phenol (DEPAP). Palladium was first selectively extracted with MFHA in isoamyl alcohol at pH 2.7-3.5 and the extract was equilibrated with a mixture of 5 M HCl and 10^{? 3} M solution of DEPAP in ethanol. The resulting intensely green ternary complex was measured at 560 nm (σ 5.1 × 10⁴ l mole^?1 cm^?1). The extraction system is suitable for enrichment of palladium over 15 times without loss in recovery and enables determination of palladium at levels as low as 10^?4 ppm (0.1 ppb). The method tolerates the presence of a large number of diverse ions normally associated with palladium, including platinum metals, and was employed for the determination of palladium in standard catalysts, biological materials, and freshwaters.     

The Fabrication and Characterization of a Bismuth Nanoparticle Modified Boron Doped Diamond Electrode and Its Application to the Simultaneous Determination of Cadmium(II) And Lead(II)

We report the simultaneous electroanalytical determination of Pb²⁺ and Cd²⁺ by square‐wave anodic stripping voltammetry (SWASV) using a bismuth nanoparticle modified boron doped diamond (Bi‐BDD) electrode. Bi deposition was performed in situ with the analytes, from a solution of 0.1 mM Bi(NO₃)₃ in 0.1 M HClO₄ (pH 1.2), and gave detection limits of 1.9 μg L^?1 and 2.3 μg L^?1 for Pb(II) and Cd(II) respectively. Pb²⁺ and Cd²⁺ could not be detected simultaneously at a bare BDD electrode, whilst on a bulk Bi macro electrode (BiBE) the limits of detection for the simultaneous determination of Pb²⁺ and Cd²⁺ were ca. ten times higher.     

Optical detection of cyanide by palladium(II)-dithiazolopyridine probe at the parts per billion level

Abstract

The ensemble of 2,6-bis(2-chlorophenyl)dithiazolo[4,5-b:5',4'-e]pyridine 1 with Pd²⁺ ions (1?Pd²⁺) was prepared for the detection of cyanide ions (CN^¯) in 50% aqueous methanol. Among the tested metal ions, only Pd²⁺ sensitively induced the red shift of the absorption bands and the complete decrease of fluorescence emission. The detection limit toward Pd²⁺ was 2?ppb. The ensemble 1?Pd²⁺ selectively and rapidly detected a low concentration of cyanide ions by a colorimetric change (40?ppb) as well as a “turn-on” fluorescent response (5?ppb). Job’s plot revealed the complex formation with 1:1 stoichiometry. The binding and replacement mode of 1?Pd²⁺ and CN^¯ were also confirmed by ¹H NMR titrations and IR analysis. In general, a fast and selective recognition of CN^¯ is reported.     

Simple and Simultaneous Method for Determination of Palladium(II) and Ruthenium(III) using Second-Order-Derivative Spectrophotometry

Abstract

A simple, sensitive, and selective second-order-derivative spectrophotometric method has been developed for the simultaneous determination of palladium(II) and ruthenium(III) using 2-hydroxy-3-methoxy benzaldehyde thiosemicarbazone (HMBATSC) as a chromophoric reagent. The reagent (HMBATSC) reacts with Pd(II) and Ru(III) at pH 3.0, forming soluble yellowish green and dark brown species, respectively. Palladium and ruthenium present in the mixture were simultaneously determined without solving the simultaneous equations by measuring the second derivative amplitudes at 445 nm and 385 nm, respectively. Further, the Beer's law was obeyed in the range 0.21–12.78 µg mL^?1 and 0.25–13.42 µg mL^?1 for Pd(II) and Ru(III), respectively. A large number of foreign ions did not interfere in the present method. The proposed method was successfully applied for the determination of palladium in hydrogenation catalysts and ruthenium in water samples.     

New Copper(II) Ion-Selective Membrane Electrode Based on Erythromycin Ethyl Succinate as a Neutral Ionophore

Abstract

The potentiometric response characteristics of a new copper(II) ion-selective PVC membrane electrode based on erythromycin ethyl succinate (EES) as ionophore were investigated. The electrode exhibited a Nernstian response to Cu²⁺ ions over the activity range of 1.5 × 10^?2 to 2.0 × 10^?6 mol L^?1 with a limit of detection of 6.3 × 10^?7 mol L^?1. Stable potentials were obtained in the pH range of 5.5–6.5. The potentiometric selectivity coefficients were calculated by using fixed interference method and revealed no important interferences except for Ag⁺. This electrode was successfully applied as an indicator electrode in determination of copper ions in real water samples.     

Solid phase extraction of Pd(II) on a newly synthesized chelating resin prior to determination by flame atomic absorption spectrometry

A new solid phase extraction method for the separation and preconcentration of Pd(II) was developed. As solid phase material, a new chelating polymer, poly [N-(4-bromophenyl)-2-methacrylamide-co-2-acrylamido-2-methyl-1-propanesulfonic acid - co-divinylbenzene] was synthesized. The parameters such as the effect of pH, eluent type, volume and concentration, flow rate of sample solution, sample volume and effect of interfering ions for the preconcentration of Pd(II) were investigated. The optimum pH was found to be 9. Eluent for quantitative elution was 10 mL of 1 mol L^?1 HCl. The preconcentration factor of the method was 75. At optimum conditions, the recovery for Pd(II) was found to be 101?±?4%. The limit of detection (3σ) was 1.1?µg L^?1. The method was applied to the determination of palladium in tap water and converter samples with satisfactory results.     

Cloud-point extraction,preconcentration, and spectrophotometric determination of palladium in water samples

The possibility of using Thio-Michler's Ketone (TMK), 4,4′-bis(dimethylamino) thiobenzophenone, for palladium(II) concentrated by micellar extraction at the cloud-point temperature, and later spectrophotometric determination, was investigated. Under the optimum conditions, preconcentration of 50?mL of water samples in the presence of 0.1% (w/v) octylphenoxy polyethoxy ethanol (Triton X-114), 2?×?10^?6?mol?L^?1?TMK and 1?×?10^–3?mol?L^?1 buffer solution (pH?=?3.0) gave the limit of detection of 0.47?ng?mL^?1, and the calibration graph was linear in the range of 2–50?ng?mL^–1. The recovery under optimum working conditions was higher than 97%. The proposed method has been applied to the spectrophotometric determination of palladium(II) in natural water samples after cloud-point extraction with satisfactory results.     

Use of clinoptilolite loaded with 1-(2-pyridylazo)-2-naphthol as a sorbent for preconcentration of Pb(II), Ni(II), Cd(II) and Cu(II) prior to their determination by flame atomic absorption spectroscopy

A solid phase extraction system for separation and preconcentration of trace amounts of Pb(II), Ni(II), Cd(II) and Cu(II) is proposed. The procedure is based on the adsorption of Pb²⁺, Ni²⁺, Cd²⁺ and Cu²⁺ ions on a column of 1-(2-pyridylazo)-2-naphthol (PAN) immobilised on surfactant-coated clinoptilolite prior to their determinations by Flame Atomic Absorption Spectroscopy (FAAS). The effective parameters including pH, sample volume, sample flow rate and eluent flow rate were also studied. The analytes collected on the column were eluted with 5 mL of 1 mol L^?1 nitric acid. A concentration factor of 180 can be achieved by passing 900 mL of sample through the column. The detection limits (3 s) for Cd, Cu, Pb and Ni were found to be 0.28, 0.12, 0.44 and 0.46 µg L^?1, respectively. The relative SDs at 10 µg L^?1 (n = 10) for analytes were in the range of 1.2–1.4%. The method was applied to the determination of Pb, Ni, Cd and Cu in water samples.     

Some Arylidene-2-Pyridylhydrazone Derivatives as Reagents for Spectrophotometric Determination of Palladium (II)

Abstract

A method for spectrophotometric determination of palladium by complexation with Arylidene-2-pyridylhydrazone derivatives in 50% (V/V) ethanolic solution are described-Pd(II) forms a 1:1 complex with the reagents. Beer's law is obeyed over the range 0.2-6.5 μg ml^?1. The effect of pH, effect of excess reagent, stability of complexes as well as the tolerance amount of many metal ions have been reported. The method is applied, with fair accuracy, to the determination of pd(II) in synthetic solutions.     

Zero-Crossing Derivative Spectrophotometric Determination of Mercury(II) And Palladium(II) with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1-3-thiazolidine and Cetyltrimethylammonium Bromide

Abstract

A method is proposed for the simultaneous determination of mercury(II) and palladium(II) by first-derivative spectrophotometry based on the absorption spectra of their complexes with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1,3-thiazolidine [5-(3,4-methoxyhydroxybenzylidene) rhodanine]. Zero-crossing measurement technique is found suitable for the measurement of the first-derivative value at the specified wavelengths. Mercury(II) (0.4-1.4 μg ml^?1) and palladium(II) (0.08 - 1.8 μg ml^?1) in different ratios have been determined simultaneously. A critical evaluation of the proposed method is performed by statistical analysis of the experimental data.     

Exploring the Oxidative‐Addition Pathways of Phenyl Chloride in the Presence of PdII Abnormal N‐Heterocyclic Carbene Complexes: A DFT Study

DFT calculations were performed to elucidate the oxidative addition mechanism of the dimeric palladium(II) abnormal N‐heterocyclic carbene complex 2 in the presence of phenyl chloride and NaOMe base under the framework of a Suzuki–Miyaura cross‐coupling reaction. Pre‐catalyst 2 undergoes facile, NaOMe‐assisted dissociation, which led to monomeric palladium(II) species 5 , 6 , and 7 , each of them independently capable of initiating oxidative addition reactions with PhCl. Thereafter, three different mechanistic routes, path a, path b, and path c, which originate from the catalytic species 5 , 7 , and 6 , were calculated at M06‐L ‐D3(SMD)/LANL2TZ(f)(Pd)/6–311++G**//M06‐L/LANL2DZ(Pd)/6–31+G* level of theory. All studied routes suggested the rather uncommon Pd^II/Pd^IV oxidative addition mechanism to be favourable under the ambient reaction conditions. Although the Pd⁰/Pd^II routes are generally facile, the final reductive elimination step from the catalytic complexes were energetically formidable. The Pd^II/Pd^IV activation barriers were calculated to be 11.3, 9.0, 26.7 kcal mol^?1 (ΔΔ^≠G_L^S‐D3) more favourable than the Pd^II/Pd⁰ reductive elimination routes for path a, path b, and path c, respectively. Out of all the studied pathways, path a was the most feasible as it comprised of a Pd^II/Pd^IV activation barrier of 24.5 kcal mol^?1 (ΔG_L^S‐D3). To further elucidate the origin of transition‐state barriers, EDA calculations were performed for some key saddle points populating the energy profiles.     

Spectrophotometric Determination of Palladium with Sodium Ethylene-Bis-Selendglycollate

Abstract

SUMMARY

Palladium was determined spectrophotometrically with sodium ethylene-bis-selenoglycollate in acid medium. The system obeys Beer' law in the range 0.25–0, 3 5 μg.ml^?1 and the molar absorptivity is 2.4 × 10⁴ 1. mol^?1 .cm^?1. Determination of palladium in the presence of many ions is reported.

In spite of the fact that selenium compounds have rarely been used as organic analytical reagents and one finds many palladium determination methods in the literature, this paper fits into the general Purpose reported before ^1,2 :systematic comparison of organic sulphur, sellenium and tellurium compounds as analytical reagents in agreement with propositions made some years agp ^3,4

In previous work⁵ the behaviour of the ethylseleno glycollic (L₁), selenodiglycollic (L₂) and ethylene-bis-selenoglycollic (L₃) anions in acidic solutions of some “soft”, “borderline” and “hard” cations was studied.

The results obtained for Pd(II) afforded evidences that its determination could be run with the three mentioned ligands.

Nevertheless, L₃ was selected because it provides the most sensitive signal and its synthesis is very simple and its overall yield is excellent⁶

From the qualitative study⁵ the foreseen selectivity could present some restrictions, but there is little doubt about the usefulness of the method that will be proposed, in various schemes of determination. Similar comments Beamish have been made about EDTA method for Pd(II) determination⁸     

Electrospun Nylon-66/5-(4-dimethylaminobenzyliden) rhodanine composite nanofibres for solid phase extraction of palladium ions from wastewater samples

In the present work, a simple procedure is presented for the extraction and determination of pre-concentrated trace amounts of palladium ions through solid phase extraction (SPE) and flame atomic absorption spectrophotometry. This process was performed using Nylon-66/5-(4-dimethylaminobenzylidene) rhodanine composite nanofibres. These nanofibres were produced under optimised conditions via two-axial electrospinning technique and characterised by scanning electron microscopy and Fourier-transform infrared spectroscopy. The effect of experimental parameters including solution pH, the type and volume of eluent and contact time was investigated in extraction and desorption process. Under the optimised conditions, good linearity in the range of 0.07–8 μg L^?1 and low detection limit of 0.015 μg L^?1 were obtained. High enrichment factor of 187.5 and good relative standard deviation of ±2.2% at 5 μg L^?1 of palladium had been achieved. The sorbent capacity for palladium adsorption was obtained 27 mg palladium per gram of nanofibres. So, the SPE was successfully applied to pre-concentrate and determine Pd(II) ions with flame atomic absorption spectrophotometer in real samples.     

Determination of Nanomolar Concentrations of Pb(II) Using Carbon Paste Electrode Modified with Zirconium Phosphated Amorphous Silica

A sensitive and selective method for the determination of Pb(II) with a zirconium phosphated silica gel (SiZrPH) modified carbon paste electrode has been developed. The measurements were carried out in three steps including an open circuit accumulation following by electrolysis of accumulated Pb(II) at the modified carbon paste electrode and differential pulse voltammetric determination. The analytical performance was evaluated with respect to the carbon paste composition, pH of solution at the accumulation step, pH and concentration of supporting electrolyte, electrolysis potential, accumulation time and electrolysis time. Two linear calibration graphs were obtained in the concentration ranges 2.5×10^?9 mol L^?1–5.0×10^?8 mol L^?1 and 5.0×10^?8 mol L^?1–5.0×10^?6 mol L^?1 with an accumulation time of 120 s. The detection limit was found to be 3.5×10^?10 mol L^?1. The effects of potential interfering ions were studied, and it was found that the proposed procedure is free from interferences of common interfering ions such as tin, thallium and etc. The developed method was applied to Pb(II) determination in a wastewater sample.