Square‐Wave Adsorptive‐Stripping Voltammetric Detection in the Quality Control of Fluoxetine

ABSTRACT

A simple and sensitive extraction-spectrophotometric method for the determination of barium and potassium is reported. The 18C6-Barium-Orange II (18C6-Ba-(OR II)₂) and 18C6-Potassium-Orange II (18C6-K-OR II) ternary complexes are quantitatively extracted into dichloromethane and their absorbances are measured at 483 nm. Linear calibration graphs were obtained over the barium concentration range of 0.1-5 μg ml^?1 and potassium concentration range of 1-8 μg ml^?1. The relative standard deviation for 2.0 μg ml^?1 barium and pottasium are, respectively, 4.16% and 3.60%. The interfering effect of a large number of diverse ions on the determination of barium and potassium was studied. The method was applied to a synthetic sample with natural matrix effects of tap water and the results showed high potential of the recommended method for the determination of Ba and K in water samples.     

Simultaneous Determination of Valsartan and Hydrochlorothiazide in Tablets by High-Performance Liquid Chromatography

ABSTRACT

A method for the simultaneous determination of valsartan and hydrochlorothiazide in tablets is described. The procedure, based on the use of reversed-phase high-performance liquid chromatography, is linear in the concentration range 5.0-10.0 μg ml^?1 for valsartan and 0.5-2.0 μg ml^?1 for hydrochlorothiazide, is simple and rapid and allows accurate and precise results. The limit of detection was 1.0 μg ml^?1 for valsartan and 0.05 μg ml^?1 for hydrochlorothiazide.     

Selective Kinetic Spectrophotometric Determination of Nitrite in Food and Water

Abstract

A highly selective and sensitive method for the kinetic spectrophothometric determination of sub-microgram amounts of nitrite has been development based on its reaction with Nile blue 2B in acidic medium. The reaction is monitored spectrophotometrically at 595 nm at a fixed time of 4.5 min. The change in absorbance at 595 nm is related to the concentration of nitrite in the range 0.005 - 1.100 μg.ml^?1 The detection limit is 0.001 μg.ml^?1. The relation standard deviation is 1% for 0.020 μg.ml^?1 of nitrite for ten replicate measurements. Most common anions and cations do not interfere. The procedure was applied to the determination of trace amounts of nitrite in sausage and water.     

Colorimetric Determination of Ampicillin and 6-Aminopenicillanic Acid Using Acenaphthenequinone as a Chromophoric Reagent

Abstract

A colorimetric method for the determination of ampicillin (Amp.) and 6-aminopenicillanic acid (6-APA) are described, based on the reaction of these drugs with acenaphthenequinone in basic media to give a highly intense red coloured product. The latter exhibits an absorption maximum at 610 nm with apparent molar absorptivities of 2.83 and 1.45 × 10⁴ l. mol^?1 cm^?1 and Sandell sensitivities of 0.013 and 0.015 μg cm^?2 for Amp. and 6-APA, respectively. The optimum concentration ranges are 0.4-10 and 0.4-14 μg ml^?1 for Amp. and 6-APA, respectively. For more accurate results, Ringbom optimum concentration ranges are 1–8.5 and 1–12 μg ml^?1 for Amp. and 6-APA, respectively. Statistical analysis indicated that there was no significant difference between the results obtained by the described method and those of the official methods. The mean recoveries percentage were found to be 99.5 × 1.1% for pharmaceutical formulations and 99.1 × 1.6% for serum and urine samples. The method is selective for the determination of Amp. or 6-APA in the presence of their degradation products, additives and excipiences that are normally encountered in dosage forms. The proposed method was applied successfully to the determination of Amp. in pharmaceutical formulations. Also, applicability of the proposed method to human serum and urine is presented and the validity assessed by applying the standard addition technique.     

Colorimetric Determination of Propofol in Bulk form,Dosage Form and Biological Fluids

ABSTRACT

Propofol is coupled with 2, 6-dichloroquinone-4-chlorimide (DCQ) in a reaction buffered at pH 9.6 to give a colored product having an analytically useful maximum at 635 nm. The factors affecting the color generation were optimized and incorporated in the procedure. The reacted propofol has a molar absorptivity of 3.9 × 10^?4 L mol^?1 cm^?1, and Beer's law is obeyed for concentrations 1-5 μg ml^?1 with detection limit 0.25 μg ml^?1. The method was found applicable to biological fluids (plasma and urine) spiked with propofol at concentration levels 1-5 μg ml^?1 for plasma and 1-5 μg 0.5 ml^?1 urine (less sensitivity is obtained with urine volumes above 0.5 ml) with detection limits 0.28 μg ml^?1 for plasma and 0.4 μg 0.5 ml^?1 urine. The average recovery for the commercial preparation (1% w/v propofol emulsion intravenous injection for infusion) was 99.54% with an RSD of 1.05%. The method was validated by an adopted HPLC method. The results obtained by the HPLC method for the commercial preparation were statistically compared with the proposed method and evaluated at the 95% confidence limits.     

Spectrophotometric Determination of Metoclopramide and Oxybuprocaine Through Ion Pair Formation with Thiocyanate and Molybdenum(V) or Cobalt(II)

Abstract

Two spectrophotometric methods involve the formation of two different ion pairs between the drug and inorganic complexes, Mo(V) and Co(II) thiocyanates followed by their extraction with dichlor?methane and o-nitrotoluene, respectively. The optimum conditions for the ion pair formation are established. The methods permit the determination of metoclopramide and oxybuprocaine hydrochlorides over a concentration range of 1-20 μg ml^?1 and 20–240 μg ml^?1 using Mo(V) and Co(II) thiocyanates, respectively. Molar ratio of drug to Mo(V) or Co(II) indicates a 2:1 ratio for the two drugs studied in the presence of excess thiocyanate concentration. Results of the analysis of drug substances and their dosage forms by the proposed methods are in good agreement with those obtained by the official methods.     

Some Arylidene-2-Pyridylhydrazone Derivatives as Reagents for Spectrophotometric Determination of Palladium (II)

Abstract

A method for spectrophotometric determination of palladium by complexation with Arylidene-2-pyridylhydrazone derivatives in 50% (V/V) ethanolic solution are described-Pd(II) forms a 1:1 complex with the reagents. Beer's law is obeyed over the range 0.2-6.5 μg ml^?1. The effect of pH, effect of excess reagent, stability of complexes as well as the tolerance amount of many metal ions have been reported. The method is applied, with fair accuracy, to the determination of pd(II) in synthetic solutions.     

Flow-Injection Chemiluminescence Determination of Fluoroquinolones

ABSTRACT

A new flow-injection CL method was developed for the determination of fluoroquinolones including ofloxacin, norfloxacin, ciprofloxacin and lomefloxacin in pharmaceutical preparations, based on the chemiluminescence reaction of sulphite with cerium(IV) sensitized by these compounds. The linear ranges are 0.04 to 4.0 μg ml^?1 for ofloxacin and 0.4 to 40.0 μg ml^?1 for norfloxacin, ciprofloxacin and lomefloxacin, respectively. The detection limits are 0.016 μg ml^?1 for ofloxacin and 0.16 μg ml ^?1 for norfloxacin, ciprofloxacin and lomefloxacin, respectively. The relative standard deviations (RSD) are 2.1 to 2.6% (n=10) for these fluoroquinolones. The analytical procedure has been applied to the determination of the fluoroquinolones in pharmaceutical commercial formulations. The results are in agreement with those obtained by the official methods.     

Fluorescent Complexes of Nucleic Acids/8-Hydroxyquinoline/Lanthanum(III) and the Fluorometry of Nucleic Acids

Abstract

The ternary fluorescent complexes of nucleic acids/8-hydroxyquinoline/ lanthanum (III) were studied. Nucleic acids in the study involve natured and thermally denatured calf thymus DNA, fish sperm DNA and yeast RNA. In the range of pH 8.0–8.4 (controlled by NH₃-NH₄Cl buffer) ternary fluorescent complexes are formed which emit at 485.0 nm for calf thymus DNA and at 480.0 nm for yeast RNA (when excited at 267.0 nm) and emits at 483.0 nm for fish sperm DNA when excited at 265.0 nm. Based on the fluorescence reactions sensitive fluorometric methods for nucleic acids were proposed. Using optimal conditions, the calibration curves were linear in the range of 0.4–3.6 μg˙ml^?1 for calf thymus DNA, 0.4–4.0 μg-ml^?1 for fish sperm DNA and 0.4–4.0 μg˙ml^?1 for yeast RNA, respectively. The limits of determination (3σ) were 0.076 μg˙ml^?1 for calf thymus DNA, 0.068 μg˙ml^?1 for fish sperm DNA and 0.329 μg˙ml^?1 for yeast RNA, respectively. Five synthetic samples were determined with satisfaction.

     

Rapid spectrophotometric determination of ruthenium(III) with prochlorperazine maleate

A rapid, simple spectrophotometric method for the determination of μg amounts of ruthenium, based on the formation of a pink complex between the metal and prochlorperazine maleate (PCPM) in sulphuric or hydrochloric acid solution, is described. The complex has an absorption maximum at 530 nm and its molar absorptivity is 6.733·10³ l mol^?1 cm^?1. The sensitivity is 0.0151 μg Ru cm^?2 for log I_o/I = 0.001. Beer's law is valid over the range 0.2–10 μg Ru ml^?1 ; the optimal range for spectrophotometric determination is 0.8–8.0 μg Ru ml^?1. Job's method of continuous variation, the mole ratio method and the slope ratio method indicate a 1:1 composition for the complex. The effects of acidity, time, temperature, order of addition of reagents, reagent concentration, and the interferences from various ions are reported.     

Fluorimetric Determination of Certain Phenothiazine Derivatives Using Eosin

Abstract

Eosin reacts with phenothiazine derivatives in dichloroethane to give intense fluorescent compounds having their excitation maximum at 318 nm and emission maxima at 450, 460 and 465 nm for prochlorperazine dimaleate, thiethylperazine dihydrochloride and trifluoperazine dihydrochloride, respectively. Under the optimum conditions, samples of 1-10 μg ml^?1 could be determined rapidly with coefficient of variation less than 1.8 %. This fluorescence reaction was also applied successfully to the determination of phenothiazine drugs in some pharmaceutical preparations.     

Determination of Morestan Residues in Water and Foodstuffs by Transmitted Room Temperature Solid Phase Spectrophosphorimetry

Abstract

A method for the determination of the pesticide morestan by means of transmitted room temperature solid phase spectrophosphorimetry has been developed. The method is based on the native phosphorescence showed by the morestan when it is fixed in a Whatman No 4 paper as a solid support. The excitation and emission wavelengths were 362 and 527 nm, respectively. The optimum phosphorescent emission was obtained when the delay time was 0.15 ms and the gate time 12.0 ms without need of a heavy atom. The linear dynamic range was between 0.1 and 1.0 μg.ml^?1, and the detection and quantification limits were 0.03 and 0.09 μg.ml^?1, respectively. The precision of the method, expressed as the relative standard deviation of ten samples at the 0.6 μg.ml^?1 concentration level, was 3.0%. The method was applied to the determination of the pesticide in different type of waters, potatoes and vegetables.     

Spectrophotometric Assay of Certain Aminoglycosides Using Cyanoacetamide

Abstract

A simple and sensitive ultraviolet spectrophotometric method has been devised for the determination of amikacin, kanamycin, neomycin and streptomycin in pure form and in some pharmaceutical preparations. The method depends on the nitrosation of the primary amino groups followed by reaction with cyanoacetamide in ammonia medium at 100°C for 30 min, The reaction products exhibit a characteristic absorption. maximum at 270 nm. Beer's law is obeyed within the concentration ranges 4–40 μg ml^?1 for amikacin, kanamycin and neomycin and 8–80 μg ml^?1 for streptomycin with apparent molar absorptivities of about 1.85 × 10⁴ for the first three compounds and 1.3×10⁴ 1. mole^?1.cm^?1 for streptomycin.     

Zero-Crossing Derivative Spectrophotometric Determination of Mercury(II) And Palladium(II) with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1-3-thiazolidine and Cetyltrimethylammonium Bromide

Abstract

A method is proposed for the simultaneous determination of mercury(II) and palladium(II) by first-derivative spectrophotometry based on the absorption spectra of their complexes with 5-(3,4-Methoxyhydroxyphenylmethylene)-2-thioxo-1,3-thiazolidine [5-(3,4-methoxyhydroxybenzylidene) rhodanine]. Zero-crossing measurement technique is found suitable for the measurement of the first-derivative value at the specified wavelengths. Mercury(II) (0.4-1.4 μg ml^?1) and palladium(II) (0.08 - 1.8 μg ml^?1) in different ratios have been determined simultaneously. A critical evaluation of the proposed method is performed by statistical analysis of the experimental data.     

Integrated Retention/Spectrophotometric Detection Method for the Determination of Formaldehyde

Abstract

An integrated-sensor method for the determination of formaldehyde based on retention of the reaction product of the analyte with p-rosaniline and sulfite in a flow-cell packed with Dowex 1-X-8 anion exchange resin was developed. The method has a good selectivity with a detection limit of 0.3 μg ml^?1 (1 ml sample) or 75 ng ml^?1 (2 ml sample), and a linear range between 1–30 μg ml^?1. The relative standard deviations (n = 11) were 2.8 and 1.3% for 2 and 20 μg ml^?1 formaldehyde, respectively. Depending on the working conditions, the sampling frenquency ranged between 10 and 18 h^?1. The method was applied to the determination of formaldehyde in well water.     

Utility of p-chloranilic Acid and 2,3 Dichloro-5,6-dicyano p-Benzoquinone (DDQ) for the Spectrophotometric Determination of Triamterene

Abstract

Two simple and sensitive spectrophotometric procedures are suggested for analysis of triamterene. The first procedure is based on the reaction of triamterene with p-chloranilic acid (p-CA) in methylene chloride to form a highly stable coloured product, exhibiting maximum absorbance at λ 530 nm. Beer's law is obeyed in the range of 40–220 μg.ml^?1 with a mean percentage accuracy of 99.98 ± 0.446. Limit of determination is 20 μg.ml^?1. In the second procedure, the drug is determined via charge transfer complex formation with 2,3 dichloro-5,6-dicyano p-benzoquinone (DDQ) using methylene chloride as a solvent. Here the reaction product has two well defined maxima at 460 nm and 530 nm where each has been utilized for quantitative determination. Beer's law is obeyed in concentration ranges of 25–125 μg.ml^?1 and 25–150 μg.ml^?1 with mean percentage accuracies of 99.92 ± 0.449 and 100.00 ± 0.511 for both maxima. 460 and 530 nm. respectively. Limit of determination is 12.5 μg.ml^?1 at both maxima. Optimum conditions for each procedure have been studied and the stoichiometry of both reactions was ascertained using Job's method of continuous variation. The validity of the suggested procedures was assessed by applying the standard addition technique using the drug capsules. Both procedures are statistically analyzed as compared with BP method for analysis of triamterene (non aqueous titration) revealing good accuracy and precision as indicated by t and F tests.     

Spectrophotometric Determination of Manganese with 4(5)-Imidazolealdoxime (Imalox)

Abstract

A method is described for the spectrophotometric determination of manganese by means of its complex with 4(5)-imidazolealdoxime, IMALOX, formed in alkaline medium. The colour system has its absorption maximum at 350 nm and obeys Beer's law over the range 0.8–8.0 μg of Mn per ml. The optimum range is 1–5 μg m^?1. The molar absorptivity is 7850 1 mol^?1 cm^?1. Relatively few ions interfere, and these can be masked with cyanide, tartrate and NTA. The experimental results have been critically analyzed and a comparison with the main spectrophotometric reagents for manganese is presented.     

Fluorimetric determination of mebendazole and flubendazole in pharmaceutical dosage forms after alkaline hydrolysis

The selective and very sensitive fluorimetric determination of mebendazole and flubendazole is based on alkaline hydrolysis and adsorption on Whatman 42 filter paper. Limits of detection are 0.1 μg ml^?1 and 0.5 μg ml^?1, respectively, with linear response sponse up to 10 μg ml^?1 and 50 μg ml^t?1. The fluorescence produced is very stable (λ_em = 460 nm) and the method is applicable to anthelmintic pharmaceutical preparations.     

Spectral Studies of Palladium(II)-Allyl Thiourea System

Abstract

Palladium(II) forms 1:1 and 1:4 complexes with allyl thiourea. The molar composition of the complexes was determined by molar-ratio and continuous variation methods and confirmed by means of elemental analysis of the compounds isolated from solution.

Conformity to Beer's law was observed for up to 12 μg ml^?1 of 4 palladium in strongly acidic medium (molar absorptivity 2.28×10⁴ 1 mol^?1 cm^?1 at 292 nm);the Sandell's sensitivity of the reaction for palladium is 0.0047 μg cm^?2 per 0.001 absorbance unit.

The tolerance of the system to platinum metals and other common cations is satisfactory.

A statistical evaluation of the analytical procedure of palladium determination has been undertaken.

The infrared spectra of allyl thiourea and of its 1:1 and 1:4 palladium complexes have been measured in the 2.5–50μ region. The absorption bands have been assigned. The spectra reveal that allyl thiourea forms sulphur-to-metal bonds only, rather than nitrogen-to-metal bonds in the complexes studied.     

Batch and flow-injection determination of ethylenediamine in pharmaceutical preparations

the ethylenediamine/pyridine-2-carbaldehyde/copper(I) system is used in a new spectrophotometric method for the determination of ethylenediamine. The batch procedure involves the formation of an orange chelate between the Schiff's base and copper(I) ions at pH 8.5 (borate buffer) and measurement of the absorbances at 475 nm against water after 10/2-15 min; Beer's law is obeyed over the range 0.5/2-11.2 μg ml^?1 and the molar absorptivity is 6.21 × 10³ l mol^?1 cm^?1. Tolerance limits for different amines [36] and other organic compounds [12] are reported. In the optimized flow-injection system, ethylenediamine (1.4/2-84.6 μg ml^?1 is determined at a sample throughput of 55 h^?1. The method is sensitive and selective and is satisfactory for the determination of the diamine in aminophylline and pharmaceutical preparations (ethylenediamine contents from 0.031 to 3.23%) with relative errors ranging from ?7.4 to +11.1% and relative standard deviations of about 0.65% for both procedures.