Determination of Phytic Acid in Urine by ICP Atomic Emission Spectrometry.

Abstract

A method to determine phytic acid within urine in the range 0.15–2 mg/l is reported. The method is based on the ICP atomic emission spectrometric determination of phosphorus, after previous separation and concentration of phytic acid using the anionic resin AG1-X8. The method has been applied successfully to determine phytic acid in synthetic urine and human urine.     

Enzymatic—spectrophotometric determination of phytic acid with phytase from Aspergillus ficuum

A method to determine phytic acid in the range 3–60 μM based on the spectrophotometric determination of inorganic phosphate with vanadate and molybdate, after liberation by enzymatic hydrolysis of phytic acid with phytase from Aspergillus ficuum at pH 2.5 and 37 °C is reported. The method has been applied successfully to determine phytic acid in wheat flour and in a pharmaceutical product.     

Studies on 1:12 phosphomolybdic heteropoly anion film modified carbon paste electrode

A 1:12 phosphomolybdic anion film modified carbon paste electrode (PMo(12) electrode) is prepared by electrochemical deposition and its application is studied by cyclic voltammetry. The film modified electrode can adsorb PMo(12) selectively and thus be used for the determination of trace phosphorus. In a solution containing 2 mug ml(-1) phosphorus, the relative standard deviation is 4.69% (n=4), the peak height also varies linearly with the concentration of phosphorus over the range 0.4-25 mug ml(-1), and the detection limit is 0.04 mug ml(-1). The method is convenient and rapid. It has been used for the determination of inorganic phosphorus in phytic acid directly with satisfactory results.     

Direct Determination of Labile Monomeric Aluminum in Natural Waters By A.C. Oscillopolarography in the Presence of Rubeanic Acid

ABSTRACT

A simple and sensitive electrochemical method for the direct determination of labile (monomeric inorganic Al speciation) Al concentration in natural waters is developed in this paper. It is based on the use of a.c. oscillopolarography in the presence of rubeanic acid (RA). The optimal experimental conditions are: 1 mol/L NaAc-HAc buffer (pH 5.4) and a RA concentration of 6x10^?4 mol/L. The response is linear over the 2x10^?7 to 2x10^?6 mol/L concentration range. The detection limit is 1x10^?7 mol/L and the relative standard deviation (at the 1.2 x 10^?6 mol/L level) is 5.5%. The method has been applied to the direct determination of labile monomeric Al concentrations in various natural samples. The results were verified by the classic ion exchange method.     

Formation of functional phosphosilicate gels from phytic acid and tetraethyl orthosilicate

Phosphosilicate gels with high phosphorus content (P mol% > Si mol%) have been prepared using phytic acid as the phosphorus precursor, with tetraethyl orthosilicate (TEOS). It is shown that the structure of phytic acid is maintained in both the sols and those gels dried at a low temperature (i.e. ≤120 °C). Solid state ²⁹Si and ³¹P NMR suggest that the gel network is primarily based on tetrahedral silicon and that phosphorus is not chemically incorporated into the silicate network at this point. X-ray diffraction shows the gel to be amorphous at low temperatures. After heat treatment at higher temperatures (i.e. up to 450 °C), P–O–Si linkages are formed and the silicon coordination changes from tetrahedral to octahedral. At the same time, the gel crystallizes. Even after this partial calcination, ³¹P NMR shows that a large fraction of phytic acid remains in the network. The function of phytic acid as chelating agent is also maintained in the gels dried at 120 °C such that its ability to absorb Ca²⁺ from aqueous solution is preserved.     

Determination of iron-porphyrin-like complexes at nanomolar levels in seawater

A new method for the non-specific determination of iron-porphyrin-like complexes in natural waters has been developed. It is based on the chemiluminescent oxidation of the luminol in the presence of dioxygen (O₂) at pH 13. The method has been implemented in a FIA manifold that allowed the direct injection of seawater. The limit of detection is 0.11 nM of equivalent hemin (Fe-protoporphyrin IX). Fe²⁺, Fe³⁺, H₂O₂, siderophore (deferoxamin mesylate), humic acid and phytic acid did not interfere when they were present at the concentrations expected in seawater. Metal free porphyrin and Mg, Cu, Co porphyrin complexes did not induce a significant chemiluminescent signal. Poisoned unfiltered samples could be stored for several weeks before analyses. The new method was successfully applied to the determination of the Fe-porphyrin complexes contained in cultured phytoplankton and in natural samples.     

Determination of phytic acid based on inhibition of crystalline growth of calcium oxalate monohydrate

It was found that the crystalline growth of calcium oxalate monohydrate seed crystals is strongly inhibited by the presence of phytic acid. The kinetics of crystal growth were followed potentiometrically using a calcium ion-selective electrode. Investigation of the process led to the development of a kinetic method for the determination of phytic acid (30–600 ng ml^?1). The procedure was applied to the direct determination of phytic acid in urine and in a pharmaceutical product.     

Flow Injection Analysis of Tannic Acid with Inhibited Electrochemiluminescent Detection

ABSTRACT

A flow injection method has been developed for the determination of tannic acid based on its inhibition of the electrochemiluminescence of luminol. The method is simple, rapid and sensitive with a detection limit of 2×10^?8 mol/l. It is effective to determine tannic acid in the range 5×10^?8 - 1×10^?5 mol/l. The variation coefficient of eleven determinations is 1.4% for 5×10^?6 mol/l. The method has been successfully applied to the determination of tannic acid in real Chinese gall and hop pellet samples.     

Fluorimetric determination of phytic acid in urine based on replacement reaction

A sensitive fluorimetric method for determination of phytic acid in human urine samples was described. The method was based on a fluorimetric replacement reaction, in which the added phytic acid replaced the Cu²⁺ ion from Cu²⁺-gelatin complex, liberating the fluorescent gelatin molecule. The fluorescence of the solution was accordingly recovered proportionally to the amount of the foreign phytic acid. The excitation wavelength was 273.5 nm and the characteristic emission wavelength was 305.0 nm, respectively. The calibration graph was obtained by plotting the recovered fluorescent intensity at maximum 305.0 nm against the added standard phytic acid, and was divided into two sections. One section was linear over the range of 0.40-2.40 mg L⁻¹ with a linear regression equation of I_f = −0.895 + 15.146c (R² > 0.9993), and the other over the range of 2.40-9.20 mg L⁻¹ with a linear regression equation of I_f = −29.526 + 26.113c (R² > 0.9996), respectively. The relative standard deviation (R.S.D.) at 95% confidence degree for a 2.0 mg L⁻¹ of standard phytic acid within 1 month was less than 1.26% (n = 5), indicating the procedure is reproducible. The detection and the quantification limits of phytic acid were estimated to be 0.23 and 0.40 mg L⁻¹, respectively. The proposed method was applied to the determination of phytic acid in urine samples and the found concentrations of phytic acid in urine were in the range of 0.49-0.75 mg L⁻¹ with recoveries of 96.2-108.8%. Comparison of the obtained results with the reported HPLC was performed, indicating the proposed method was reliable.     

Derivative activation analysis of phosphorus at ppb levels in water samples

A neutron activation analysis procedure has been developed for the indirect determination of phosphorus as orthophosphate at ppb levels, via the formation of antimonyl phosphomolybdic acid. The complex is adsorbed on Sephadex G-25 resin and the antimony is estimated through NAA, allowing the determination of phosphorus. The procedure provides an easy method to adopt for the routine determination of phosphorus at 10 ng ml^–1 levels with good precision, in water samples.     

Purity Determination of Phosphorus Compounds by Internat- Standard31 P Nmr Spectroscopy. an Experimental Study and Validation

Abstract

Due to the proportionality between the area of the NMR signal and the number of nuclei, internal standard³¹P NMR spectroscopy is in principle a rapid and simple method for determination of the purity of phosphorus compounds.nuclei, internal standard³¹P NMR spectroscopy is in principle a rapid and simple method for determination of the purity of phosphorus compounds.nuclei, internal standard³¹P NMR spectroscopy is in principle a rapid and simple method for determination of the purity of phosphorus compounds.nuclei, internal standard³¹P NMR spectroscopy is in principle a rapid and simple method for determination of the purity of phosphorus compounds.     

Measurement of Phosphorus in Metals by RNAA

An RNAA procedure has been developed for measurement of low-level phosphorus in metals. Samples are irradiated at a neutron flux of 2.7·10¹³ n·cm^–2·s^–1 then mixed with carrier and dissolved in acid. After chemical separation and purification of the phosphorus and gravimetric determination of carrier yield, ³²P is determined using a beta proportional counter. The detection limit for a 0.1 g sample irradiated for 30 minutes is 5 g/kg. The method has been used to determine 6.4±0.6 mg/kg phosphorus in SRM 2175 refractory alloy.     

Bulk Acoustic Wave Sensor for Non-suppressed Ion Chromatographic Determination of Nitrate and Other Inorganic Anions in Vegetables

Abstract

A new type of bulk acoustic wave sensing device based on a conductivity-bulk acoustic wave frequency response is applied in ion chromatography to determine nitrate and other inorganic ions in vegetables. The present method has the advantages in its rapidity, simplicity, sensitivity and accuracy. Detection limits (peak=3[sgrave]) are obtained for NO₃ ^?, Cl^?, NO₂ ^?, H₂PO₄ ^? and SO₄ ^2? at concentrations of 1, 0.6, 1, 7 and 3 ng (on column), respectively. Neither derivatization nor a clean-up step is necessary besides filtration. For the IC analysis, the analytical column is a Shim-pack IC AI column, and the eluent is 2.0 mM phthalic acid solution with pH 4.0. A comparison of IC-SBAW with conventional IC is made. The method allows the simultaneous determination of nitrate and other inorganic ion levels in vegetables.     

Investigation of A New Catalytic Reaction of Complex Formation of Cobalt (III) With Nitroso-R-Salt for the Determination of Microquantities of Phosphate-Ions

ABSTRACT

The catalytic action of phosphate-ions on the reaction of complex formation of cobalt (III) with nitroso-R-salt in a weakly acid medium has been found. The dependence of the rate of the catalytic reaction on temperature, concentrations of reagents and catalyst, pH of the medium, as well as on the presence of some anion and non-ion surface-active substances and accompanying inorganic minerals was studied. The optimum conditions for the determination of 0.1 μg/ml PO^3- ₄ in water were determined. A technique for the determination of phosphate-ion impurity up to 9×10^-5% in the high-purity sodium iodide and 2×10^-4% cesium iodide used for the single crystals growth is suggested.     

The reduction process of phytic acid–silver ion system: A pulse radiolysis study

Reduction of silver ion in a silver–phytic acid (1:1 ratio) system has been studied using pulse radiolysis technique. Time-resolved transformation of the intermediates, Ag⁺→Ag⁰→Ag₂⁺→Ag₃²⁺, has been clearly observed in the reduction of silver–phytic acid (1:1) system. The effect of phytic acid on the formation and decay of initial silver clusters has been also studied. The surface plasmon absorption band of stable silver nanoparticle (410 nm) and dynamic light scattering technique has been used to characterize the nanoparticles and measure the average size (R_av=100 nm).     

A radioreagent method for determination of traces of phosphorus in high-purity silicon

The present study explores the feasibility of the determination of phosphorus at the extreme trace levels in high-purity silicon by radioreagent method. After silicon dissolution with hydrofluoric and nitric acids and matrix volatilization, 12-molybdophosphoric acid (12-MPA) is formed by the addition of the radioreagent,⁹⁹MoO ₄ ^2– , in nitric acid medium and then extracted into isobutyl acetate. By plotting the phosphorus content against the radioactivity of⁹⁹Mo in the organic phase, a linear relationship persisting down to 5 ng is obtained. Special effort has been made to the elimination of the unreacted⁹⁹MoO ₄ ^2– reagent and the optimal control of phosphorus blank introduced through the multistage analytical procedure in order to ensure reliable determination of phosphorus at the ppb level.     

A New Redox Initiating System for the Polymerization of Vinyl Monomers

Abstract

A new redox system, dioxane-ascorbic acid, has been investigated for the homopolymerization of vinyl monomers. Detailed kinetic studies on the aqueous polymerization of acrylamide by this initiating system have been done iodometrically at 35 ± 0.2°C. The effect of various additives, such as organic solvents, inorganic salts, surfactants, etc., on the rate of polymerization has been studied. The retardation constants for organic solvents have been evaluated by the “intercept method.” The overall energy of activation has been found to be 8.75 kcal/deg/mol, within the temperature range 25–45°C. A suitable mechanism has been suggested. The following rate expression: R_p α [acrylamide]^1.0 [dioxane]^1.0 [ascorbic acid]⁰, has been observed.     

The Determination of Trace Amounts of Phosphate in Natural Water by Flow Injection Fluorimetry

Abstract

A new method is suggested for the determination of trace amounts of phosphate by flow injection fluorimetry, based on the principle that molybdophosphate could quench the fluorescence of Rhodamine 6G. The fluorescence is excited at 350 nm and measured at 550 nm. The calibration graph is linear up to 100 ng/ml phosphorus concentration and the detection Unit is 1.9 ng/ml. The present method has been applied to the determination of soluble phosphorus in natural water samples, the recoveries were in the range of 92 – 102 %. The sampling rate is 120 samples per hour.     

Determination of Nitrilotriacetic Acid in Waters and Waste Waters by Gas-Liquid Chromatography,Differential Pulse Polarography and a Colorimetric Method

Abstract

A comparison of gas-liquid chromatography, differential-pulse polarography and a colorimetric method for the determination of nitrilotriacetic acid in settled sewage, sewage effluent, potable water, soil extracted water and deionised water has been undertaken. Differential-pulse polarography has also been applied to the determination of nitrilotriacetic acid in saline samples. By statistical analysis of replicate determinations, accuracy and precision have been evaluated, and calibration linearity assessed. Interferences were observed for sewage samples when analysed by all three methods. Precision was generally higher for differential-pulse polarography down to 100 μgl^?1, although only gas-liquid chromatography is applicable to concentrations below 25μgl^?1 in non-saline samples. The colorimetric method was not applicable to concentrations below 500 μgl^?1 of nitrilotriacetic acid.     

Capillary Electrophoretic Determination of Disodium Ethylene Bisdithiocarbamate (NABAM) and Sodium Diethyldithiocarbamate (NADDC)

Abstract

A simple and sensitive capillary elecrophoretic method has been developed for the separation and determination of Nabam and NaDDC in boric acid buffer by direct UV absorbance detection at 254 nm. The separation is dependent on pH and nature of the buffer. In this method the detection limits (S/N = 3) are 1.56 × 10^?6 mol/L and 2.48 × 10^?6 mol/L and the linear calibration range is three orders of magnitude for Nabam and NaDDC, respectively. The method has been successfully applied for the analysis of wheat samples spiked with Nabam.