Biphenol as an Electron Transfer Mediator for Glucose Oxidase

Abstract

Biphenol (4,4′-dihydroxy-biphenyl) was found to be an electron transfer mediator for glucose oxidase (GOD) of Aspergillus niger. At a glassy carbon electrode, a 1.44×10^-4 M solution of biphenol in phosphate-buffered saline (PBS) at pH 7.4 gives an quasi-reversible, one-electron, pH-sensitive couple at 255mV (relative to the standard calomel electrode). The apparent second-order rate constant for electron transfer from reduced GOD to oxidized biphenol was determined to be 3×10⁵ M^-1 s^-1. When biphenol and GOD are cophysiadsorbed on a graphite electrode immersed in PBS and held at 400mV, a glucose-dependent current response is noted. In addition to the predominant quasi-reversible biphenol redox couple, repetitive cyclic voltammetry at a graphite electrode gave rise to a polybiphenol polymer; this is most marked at a pH above the biphenol pK_a of about 9.5. At pH 7.4, the polymerization is less significant. Polybiphenol formed either side of the pK_a remains electrochemically active (E°_app. = 245mV) but no longer mediates GOD.     

Determination of Pseudoephedrine Hydrochloride in Some Pharmaceutical Drugs by Potentiometric Membrane Sensor Based on Pseudoephedrine–Phosphotungstate Ion Pair

Abstract

An ion-selective electrode (ISE) was developed for the rapid determination of pseudoephedrine hydrochloride (PSEHCl) in pharmaceutical preparations. The electrode incorporates a PVC membrane with a pseudoephedrine–phosphotungstate ion pair complex. The influences of membrane composition, temperature, pH of the test solution, and the interfering ions on the electrode performance were investigated. The sensor exhibits a Nernstian response for pseudoephedrine hydrochloride ions over a relatively wide concentration range (1.0 × 10^?1 to 1.0 × 10^?5 mol L^?1) with a slope of 56.2 ± 0.5 mV per decade at 25°C. It can be used in the pH range 4.0–10.5. The isothermal temperature coefficient of this electrode amounted to 0.0009 V/°C. The membrane sensor was successfully applied to determination of PSEHCl in its tablets and syrup.     

An Amperometric Glucose Electrode Based on Adsorbed Glucose Oxidase on Palladium/Gold Modified Graphite

Abstract

A glucose electrode was constructed by adsorbing glucose oxidase (GOD) on a modified electrode for H₂ O ₂ oxidation, consisting of Pd/Au sputtered on graphite. Maximally, 0.8 U cm^?2 of GOD could be adsorbed. The electrode was used in a f.i.a. manifold for determination of glucose. Linear calibration curves were obtained in the concentration range 3. 10^?6 4. 10^?3 mol L^?1 glucose. The applied potentials for glucose determination were + 300 mV vs. Ag/AgCl at pH 8.0, + 350 mV at pH 7.0, + 400 mV at pH 6.0 and + 500 mV at pH 5.0. The activity vs. pH profile of adsorbed GOD was broad having an optimum between pH 5 and 6. The apparent kinetic parameters for adsorbed GOD, K_M ^app and i_max, were found to be 50 mM and 160 uA at optimal pH.     

Amperometric Glucose Biosensor Based on Rhodium Dioxide‐Modified Carbon Ink

An amperometric method for the determination of glucose using a screen printed carbon electrode is reported. The electrode material was bulk modified with rhodium dioxide and the enzyme glucose oxidase immobilized in a Nafion‐film on the electrode surface and investigated for its ability to serve as a detector of glucose in flow injection analysis. The sensor exhibited a linear increase of the amperometric signal with the concentration of glucose in the range of 1–250 mg L^?1 with a detection limit (evaluated as 3σ) of 0.2 mg L^?1 under optimized flow rate of 0.4 mL min^?1 in 0.1 M phosphate buffer (pH 7.5) carrier. At the potential applied (?0.2 V vs. Ag/AgCl), interferences from redox species present in the sample matrix were negligible. The biosensor reported here retained its activity for more than 40 injections or 4 months of storage at 6 °C. The RSD was determined as 1.8% for a glucose concentration of 25 mg L^?1 (n=5) with a typical response time of about 28 s.     

Determination of betamethasone sodium phosphate in pharmaceuticals by potentiometric membrane sensor based on its lidocaine ion pair

Betamethasone sodium phosphate (BMNaP) has been employed as an electroactive material in the design of an ion-selective electrode (ISE). The electrode incorporates PVC membrane with betamethasone sodium phosphate-lidocaine ion pair complex. The influences of membrane composition, temperature, pH of the test solution, and the interfering ions on the electrode performance were investigated. The sensor exhibits a Nernstian response for betamethasone sodium phosphate ions over a relatively wide concentration range (1.0 × 10^?1 to 1.0 × 10^?5 M) with a slope of 28.4 ± 0.9 mV per decade at 25°C. It can be used in the pH range 4.0–10.0. The isothermal temperature coefficient of this electrode amounted to ?0.0008 V/°C. The membrane sensor was successfully applied to the determination of betamethasone sodium phosphate in pharmaceutical products.     

Development of a Novel Silver Nanoparticles-Enhanced Screen-Printed Amperometric Glucose Biosensor

Abstract

A disposable glucose biosensor is developed by immobilizing glucose oxidase into silver nanoparticles-doped silica sol-gel and polyvinyl alcohol hybrid film on a Prussian blue-modified screen-printed electrode. The silver nanoparticles-enhanced biosensor shows a linear amperometric response to glucose from 1.25 × 10^?5 to 2.56 × 10^?3 with a sensitivity of 20.09 mA M^?1 cm^?2, which is almost double that of the biosensors without silver nanoparticles. The immobilized glucose oxidase retained 91% of its original activity after 30 days of storage in phosphate buffer (pH 6.9; 0.1 M) at 4°C. Blood glucose in a rabbit serum sample was successfully measured with the biosensor.     

Development of Nalbuphine‐Selective Membrane Electrode and Its Applications in Pharmaceutical Analysis

Abstract

A nalbuphine ion‐selective PVC membrane electrode based on ion‐pair complex of nalbuphine with tetra phenyl borate was prepared with di‐butyl sebacate as a plasticizer. The electrode exhibits a linear response with a Nernstain slope 59.6 mV decate^?1 at 25°C with the concentration range of 1×10^?6?1×10^?2 M nalbuphine. The electrode response was not sensitive to pH changes from 3.5–7 and not affected by possible interfering species such as common inorganic cations, sugars and amino‐acids. The electrode shows good stability, reproducibility and fast response. These characteristics of the electrode enable it to be used successfully for the determination of nalbuphine hydrochloride in pure form and in pharmaceutical preparations.     

Carbon-Paste Electrodes with Incorporated Lactate Oxidase and Mediators

Abstract

Amperometric bipelectrodes based on carbon paste modified with L-lactate oxidase and mediators are described which are sensitive to L-lactaie. Several ferrocenes and phenoxazine derivatives as mediators are evaluated, with Meldola blue exhibiting the best results.

With ferrocene derivatives the bioelectrodes were operated at potential of 0.2-0.4 V (vs SCE). The apparent Michaelis constants for the calibration curves of the bioelectrodes are different depending on the chosen mediator and varied in the range from 0.9 to 3.6 mM L-lactate. The pH optimum in the case of the 1,1′-dimethylferrocene bioelectrode was 9.3 and the limiting sensitivity was determined to be 31 μA/mM cm^?2. Covered by a Nation membrane, the electrode sensitivity was in the range of 3.2-4.4 μA/mM cm^?2 at pH 7.0 and the calibration range was linear up to 2-2.5 mM L-lactate.

The bioelectrode based on Meldola blue mediated electron transfer at potentials between 0.05-0.25 V. The Km(app) was 17.0 and 18.2 mM at 0.1 and 0.05 V, respectively. The pH optimum of the bioelectrodes was 7.9 and limiting sensitivity - 164μA/mM cm^?2.

At normal physiological level of ascorbic acid (50 μM) in blood the response of the Meldoia blue based sensors was 5.3 % at 0.1 V, whereas that of the 1,1′-dimethylferrocene bioelectrode was 83 % at 0.25 V in comparison to the response observed with physiological levels of L-lactate (2 mM).     

Barium(II)-PVC Membrane Sensor Based on 4-4′-Methylenediantipyrine as a Neutral Carrier

Abstract

A highly selective and sensitive poly(vinyl chloride) membrane electrode, using 4-4′-Methylenediantipyrine as an ionophore, has been prepared and examined as a Ba²⁺-selective electrode. The influence of the anion excluder (sodium tetraphenyl borate, NaTPB) and the effect of the plasticizers dibutyl phthalate (DBP), nitrobenzene (NB), and benzyl acetate (BA) were studied. The best performance was obtained with the sensor having a membrane composition (w/w) of (MAP, 2.0%), (PVC, 30%), (NB, 66%), (NaTPB, 2.0%) with a wide working concentration range of 1.0 × 10^?6 to 1.0 × 10^?2 M between the pH values of 3.4 and 10.6. Furthermore, a Nernstian slope of 29.7±0.3 mV/decade of activity was demonstrated with a response time of 15 s. The sensor could be used over a period of 2 months with no potential divergence, revealing a good selectivity for a broad variety of cations including alkali, alkaline earth, heavy and transition metals. Regarding the practical applicability of this sensing device, it was successfully applied for the Ba²⁺ ions detection in a lithophone pigment and as an indicator electrode in the potentiometric titration of the under study cations.     

Cobalt(II)-selective membrane electrode based on N,N′-di(thiazol-2-yl)formimidamide

A new PVC-membrane electrode for Co²⁺ ions based on N,N′-di(thiazol-2-yl)formimidamide (TF) as membrane carrier has been developed. The electrode resulted in Nernstian response (29.5?±?0.4?mV decade^?1) for Co²⁺ ion over a wide concentration range (2.5?×?10^?7 ?1.0?×?10^?1?M) with a detection limit of 6.1?×?10^?8?M. The sensor has a response time of about 10?s, and can be used for at least 2 months without observing any deviation from the Nernstain response. The electrode revealed good selectivity towards cobalt(II) ion over a wide variety of alkali, alkaline earth, transition, and heavy metal ions and could be used in the pH range 2.0–7.0. The electrode was used for determination of Co²⁺ in real samples.     

1,1′-Dimethylferrocene Mediated L-Glutamate Electrodes Modified With Electropolymerized 1,3-Diaminobenzene Film

Abstract

A mediated L-glutamate biosensor was constructed by incorporating 1,1′-dimethylferrocene in electropolymerized 1,3-diaminobenzene and immobilizing L-glutamate oxidase on the electropolymerized film. Stabilizers (1% DEAE-dextran, 1% MgCl₂ and 10% sucrose) were added to the immobilized enzyme to improve the long-term storage stability. The electrode responded linearly to L-glutamate concentration between 0.1 and 2.0 mM and the response of the electrode did not interfere with electroactive species and oxygen. The useful lifetime of the sensor was at least 3 weeks. When stored in dry form at 28°C, the sensor with stabilizers was stable at least 6 months. The electrode was applied to determine L-glutamate in fermentation broth samples. Good correlations were achieved between results obtained with the sensor and by enzymatic analysis using glutamate dehydrogenase.     

Direct Electron Transfer of Glucose Oxidase and Glucose Biosensor Based on Nano-structural Attapulgite Clay Matrix

The direct electrochemistry of glucose oxidase (GOD) was achieved based on the immobilization of GOD on a natural nano‐structural attapulgite (ATP) clay film modified glassy carbon (GC) electrode. The immobilized GOD displayed a pair of well‐defined quasi‐reversible redox peaks with a formal potential (E^0′) of ?457.5 mV (vs. SCE) in 0.1 mol·L^?1 pH 7.0 phosphate buffer solution. The peak current was linearly dependent on the scan rate, indicating that the direct electrochemistry of GOD in that case was a surface‐controlled process. The immobilized glucose oxidase could retain bioactivity and catalyze the oxidation of glucose in the presence of ferrocene monocarboxylic acid (FMCA) as a mediator with the apparent Michaelis‐Menten constant K^app_m of 1.16 mmol·L^?1. The electrocatalytic response showed a linear dependence on the glucose concentration ranging widely from 5.0×10^?6 to 6.0×10^?4 mol·L^?1 (with correlation coefficient of 0.9960). This work demonstrated that the nano‐structural attapulgite clay was a good candidate material for the direct electrochemistry of the redox‐active enzyme and the construction of the related enzyme biosensors. The proposed biosensors were applied to determine the glucose in blood and urine samples with satisfactory results.     

A glucose sensor based on glucose dehydrogenase adsorbed on a modified carbon electrode

A glucose sensor is prepared by adsorption of the mediator Meldola blue (N,N-dimethyl-7-amino-1,2-benzophenoxazinium ion, as well as glucose dehydrogenase, on the surface of a carbon electrode. The nicotinamide coenzyme, whhich is present in the solution, is reduced in the enzymatic reaction and is re-oxidized amperometrically at 0 mV vs. Ag/AgCl. The properties of such electrodes depend on whether the mediator or the enzyme is adsorbed first; possible models for the molecular arrangements at the surface are discussed. The modified electrode is mounted in a flow-through cell in a flow-injection system and tested with 50-μl injections of β-d-glucose. The calibration graphs were linear in the range 5 × 10^?6—2 × 10^?3 M βd glucose with the highest sensitivity at pH 6.0. The membrane-free enzyme electrode has a fast response; peak widths are 12 s at half height (flow rate 0.7 ml min^?1, making it possible to process 100 samples h^?1.     

Construction and Performance Characteristics of a Chromotropate Sensing Plastic Membrane Electrode

Abstract

The lipophilic salt hexadecylpyridinium chromotropate (HDP)₂CT is used as ion exchanger in preparation of plastic membrane electrode sensitive to chromotropate anion. the electrode has the following main characteristics: slope ?29.0. mV decade_?1 (at 25°C), response time 5–10 sec, linear concentration response 7.9 × 10_?5?3.2 × 10_?2 M, usable pH range 5.0–10.5, isothermal temperature coefficient 0.00037 V/°C and maximum working temperature 52°C. the electrode is very selective for chromotropate towards many inorganic and organic anions. the solubility product of (HDP)₂CT is determined potentiometrically using the concerned electrode. the standard addition method is used to determine CT_?2 in presence of KCl (0.1 M) with satisfactory results, confidence limit of the mean value (95 % probability) was (1.78 ± 0.03) × 10_?11.     

Amperometric Biosensor for Adenosine-5′-Triphosphate Based on a Platinum-Dispersed Carbon Paste Enzyme Electrode

Abstract

A new amperometric biosensor for adenosine-5′-triphosphate (ATP) was designed using a platinum-dispersed carbon paste into which glycerol kinase and glycerol-3-phosphate oxidase were incorporated. The biosensor is based on the detection of hydrogen peroxide produced by the enzymatic reaction of ATP with glycerol and the subsequent oxidation of glycerol-3-phosphate. The use of the platinum-dispersed carbon paste electrode lowered the oxidation potential for hydrogen peroxide, permitting the sensitive detection of ATP at 0.4 V vs. Ag/AgCl. A linear response to ATP was observed in the concentration range of 1 x 10^?5 to 2.5 x 10^?3 M.

     

Electrochemiluminescence Biosensor for Glucose Based on Graphene/Nafion/GOD Film Modified Glassy Carbon Electrode

Glucose oxidase(GOD) was encapsulated in the Graphene/Nafion film modified glassy carbon electrode(GCE) and used as an ECL sensor for glucose. The GOD retains its bioactivity after being immobilized into the composite film. The sensor gives a linear response for glucose in the range of 2.0×10^?6–1.0×10^?4 mol/L with a detection limit of 1.0×10^?6 mol/L. The sensor showed good stability, the RSD for continuous scanning for 5.0×10^?5 mol/L glucose was 4.21 % (n=5). After being stored in 0.05 mol/L pH 7.4 PBS in 4 °C for two weeks, the modified electrode maintains 80 % of its initial activity. The glucose sensor provides new opportunity for clinical diagnosis applications.     

Mediated amperometric biosensor for hypoxanthine based on a hydroxymethylferrocene-modified carbon paste electrode

An amperometric enzyme electrode for the determination of hypoxanthine in fish meat is described. The hypoxanthine sensor was prepared from xanthine oxidase immobilized by covalent binding to cellulose triacetate and a carbon paste electrode containing hydroxymethylferrocene. The xanthine oxidase membrane was retained behind a dialysis membrane at a carbon paste electrode. The sensor showed a current response to hypoxanthine due to the bioelectrocatalytic oxidation of hypoxanthine, in which hydroxymethyiferrocene served as an electron-transfer mediator. The limit of detection is 6 × 10^?7 M, the relative standard deviation is 2.8% (n=28) and the response is linear up to 7 × 10^?4 M. The sensor responded rapidly to a low hypoxanthine concentration (7 × 10^?4 M), the steady-state current response being achieved in less than 1 min, and was stable for more than 30 days at 5 ° C. Results for tuna samples showed good agreement with the value determined by the conventional method.     

Determination of Some Phenothiazines Compounds in Pharmaceuticals and Human Body Fluid by Electrocatalytic Oxidation at a Glassy Carbon Electrode Using Methylene Blue as a Mediator

Abstract

A glassy carbon electrode plus Methylene blue as a mediator was employed to study and sense the electrocatalytic oxidation of phenothiazines, including chlorpromazine, perphenazine, promazine, and fluphenazine, using cyclic voltammetry and chronoamperometry as diagnostic techniques. The electron-transfer coefficient, alpha (= 0.45), for phenothiazines compounds at the surface of glassy carbon electrode was determined using a cyclic voltammetry technique. It was found that under a selected pH (8.6) the peak current due to the oxidation of Methylene blue at the surface of the electrode that occurrs at a potential of about ? 180 mV is proportional to the phenothiazines concentration. Linear analytical curves were obtained in the ranges of 1.0 × 10^?6 ? 2.1 × 10^?4 mol L^?1 for the phenothiazines compounds. The influences of potentially interfering substances on the current response of the system were examined. The method was used for the determination of phenothiazines compounds, including chlorpromazine, perphenazine, promazine, and fluphenazine in human.     

PPb Level Monitoring of Dy(III) Ions by a Highly Sensitive and Selective Dy(III) Sensor Based on a New Asymmetrical Schiff's Base

Abstract

A Dy(III) ion‐selective membrane sensor has been fabricated from polyvinyl chloride (PVC) matrix membrane containing a new asymmetrical Schiff's base [(E)‐N‐(2‐hydroxybenzylidene)benzohydraide] or BBH as a neutral carrier, sodium tetraphenyl borate (NaTPB) as an anionic excluder and nitrobenzene (NB) as a plasticizing solvent mediator. The membrane sensor displays linear potential response in the concentration range of 1.0×10^?2–1.0×10^?6 M of Dy(III). The electrode exhibits a nice Nernstian slope of 20.1±0.8 mV/decade in the pH range of 3.0–8.0. The sensor has a relatively short response time in whole concentration ranges (<20 s). The detection limit of the proposed sensor is 8.0×10^?7 M (～128 ng/mL), and it can be used over a period of six weeks. The selectivity of the proposed sensor with respect to other cations, (alkali, alkaline earth, transition and heavy metal ions) and especially lanthanid ions, is excellent. The practical utility of the sensor has been demonstrated by using it as an indicator electrode in the potentiometric titration of Dy(III) with EDTA.     

Response Amplification of an Ion-Selective Electrode

Abstract

The response of an ion-selective electrode can be amplified by connecting the cell, which is composed of an ion-selective electrode and a reference electrode, in series. For a cell using 1, 2 or 3 valinomycin electrodes connected in series, the response slopes to 1 × 10^?5 ?1 × 10^?1 M K⁺ were 58, 116 and 174 mV/activity decade (a.d.) at 25°C, respectively. This amplification method would especially be useful for accurate determinations with electrodes in the range of low concentrations outside the Nernstian response or for determinations of polyvalent ions, in which both cases exhibit small emf response changes in changing the ion concentration.